2024-2026 Cupra Terramar SUV Wheels and tyres -> Important information about wheels and tyres User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Important information about wheels and tyres for Your Cupra Terramar SUV First Generation (2024-2026)

374
Wheels and tyres
Wheels and tyres
Important information
about wheels and tyres
General notes
●
When driving with new tyres, be especially
careful during the rst 600 km (300 miles).
●
If you have to drive over a kerb or similar ob-
stacle, drive very slowly and as near as possible
at a right angle to the obstacle.
●
Check from time to time if the tyres are
damaged (punctures, cuts, cracks or dents).
Remove any foreign objects embedded in the
treads.
●
Damaged wheels and tyres must be replaced
immediately.
●
Keep grease, oil and fuel o the tyres.
●
Replace any missing valve caps as soon as
possible.
●
Mark the wheels before taking them o so
that they rotate in the same direction when put
back.
●
When removed, the wheels or tyres should
be stored in a cool, dry and preferably dark
place.
Low prole tyres
Low prole tyres have a wider tread, a larger
wheel diameter and a lower sidewall height.
This results in more agile driving behaviour.
Low prole tyres may deteriorate more quickly
than standard tyres, for instance due to
heavy impacts, potholes, manhole covers and
kerbs. Correct tyre pressure is very important
›››page376.
To avoid damage to tyres and wheels, drive
with special care when driving on roads in poor
condition.
Visually check your wheels every 3000 km.
If the tyres or rims have received a heavy im-
pact or have been damaged, have a special-
ised workshop check whether or not it is nec-
essary to change the tyre.
Low prole tyres may deteriorate more quickly
than standard tyres.
Concealed damage
Damage to tyres and rims is often not readily
visible. If you notice unusual vibration or the
car pulling to one side, this may indicate that
one of the tyres is damaged. Reduce speed im-
mediately if there is any reason to suspect that
damage may have occurred. Inspect the tyres
for damage. If no external damage is visible,
drive slowly and carefully to the nearest speci-
alised workshop and have the car inspected.
Foreign objects inserted in the tyre
●
Do not remove foreign bodies if they have
penetrated through the tyre wall!
●
If the vehicle comes with a tyre mobility sys-
tem, where necessary seal the damaged tyre as
shown in section ›››page388.
Use a specialised workshop for repair or re-
placement. CUPRA recommends going to a
specialised CUPRA dealer or any SEAT dealer-
ship for this purpose.
The sealant inside the tyre tread wraps around
the foreign body and provisionally seals the
tyre.
Tyres with directional tread pattern
An arrow on the tyre sidewall indicates the
rotation direction on directional tyres. Always
note the rotation direction indicated when
mounting the wheel. This makes sure that op-
timal use is made of tyre properties in terms of
aquaplaning, grip, excessive noise and wear.
Retrotting of accessories
If you wish to change or t wheels, rims or
wheel trims, we recommend that you consult
with a specialised CUPRA Service or SEAT Oi-
cial Service centre for advice regarding current
technical recommendations.
Speed symbols
The speed rating indicates the maximum
speed permitted for the tyres.
Wheels and tyres
375
Important information about wheels and tyres
P
Q
R
S
T
U
H
V
Z
W
Y
max.150 km/h (93mph)
max.160 km/h (99mph)
max.170 km/h (106mph)
max.180 km/h (112mph)
max.190 km/h (118mph)
max.200 km/h (124mph)
max.210 km/h (130mph)
max.240 km/h (149mph)
max.240km/h (149mph)
max.270 km/h (168mph)
max.300 km/h (186mph)
WARNING
●
New tyres do not have maximum grip dur-
ing the rst 600km. Drive particularly care-
fully to avoid possible accidents.
●
Never drive with damaged tyres. This may
cause an accident.
●
If you notice unusual vibrations or if the
vehicle pulls to one side when driving, stop
the vehicle immediately and check the tyres.
●
Never use old tyres or those with an un-
known history of use.
New wheels and tyres
It is best to have all wheels and tyres serviced
by a specialised workshop. There they have the
required knowledge, the special tools and the
corresponding spare parts.
●
Even winter tyres lose their grip on ice. If you
have installed new tyres, drive the rst 600 km
carefully and at a moderate speed.
●
All four wheels must be tted with tyres
of the same type, size (rolling circumference)
and, if possible, tread pattern.
●
When changing tyres, do not change just
one; change at least two on the same axle.
●
If you want to equip your vehicle with a com-
bination of tyres and rims that are dierent to
those tted in the factory, inform your special-
ised workshop before purchasing them
The sizes of the rims and tyres approved for
your vehicle are listed in the vehicle documen-
tation (e.g. EC Certicate of Conformity or
COC document). The vehicle documentation
varies depending on the country of residence.
If the type of spare wheel is dierent form
the normal wheels — e.g. in the case of win-
ter tyres or particularly wide tyres — the spare
wheel should only be used temporarily in the
event of a puncture, and the vehicle should be
driven with care. Ret the normal road wheel
as soon as possible.
In vehicles with four-wheel drive, the 4 wheels
must be tted with tyres of the same brand,
type and tread so that the traction system is
not damaged by a dierence in the number of
turns of the wheels. Therefore, in the event of
a puncture, only a spare wheel with the same
perimeter as normal tyres should be used.
Manufacturing date
The manufacturing date is also indicated on
the tyre sidewall (or on the inside face of the
wheel):
DOT ... 2220 ...
this means, for example, that the tyre was
manufactured in the 22nd week of 2020.
WARNING
●
Use only combinations of tyres and rims,
as well as suitable wheel nuts, approved by
CUPRA. Otherwise the vehicle may be dam-
aged, causing an accident.
●
For technical reasons it is not possible to
use wheels of other vehicles; in some ca-
ses not even wheels from the same vehicle
model should be used.
●
Always ensure that the tyres you have
chosen have adequate clearance. When se-
lecting replacement tyres, do not rely en-
tirely on the nominal tyre size marked on the
tyre, since the nominal tyre size can dier
signicantly depending on the manufacturer.
Lack of clearance can damage the tyres or
the vehicle and, as a result, endanger road
safety. Accident hazard!
376
Wheels and tyres
●
Only use tyres that are over 6 years old in
an emergency, and drive with due care.
●
The tting of tyres with run-at properties
is not permitted on your vehicle! Prohibited
use can cause accidents or can damage your
vehicle.
●
If decorative hubcaps are retrotted, make
sure that they allow enough air in to cool the
braking system. Accident hazard!
●
Models with aerodynamic wheel rims
and/or with bolt-on plastic elements (more
enclosed design) increase the likelihood of
ice and snow accumulating on the inside.
This should be taken into account, depend-
ing on the driving situations, as snow or ice
accumulated in the wheels can cause vibra-
tion in the vehicle when it drives at over 40
km/h. It is advisable to remove ice and snow
from the inside of the wheels using hot water.
●
If you drive on dirt or gravel tracks, the
likelihood of stones becoming trapped inside
wheel rims with plastic elements increases
when driving at high speed or in a sporty
manner. If you see that there are stones trap-
ped between the aluminium wheel rim and
the insert, you can attempt to remove them
using pressurised water.
For the sake of the environment
Old tyres must be disposed of according to
each country's laws.
Note
●
A CUPRA Service Centre should be consul-
ted to nd out whether wheels or tyres of
dierent sizes to those originally tted by
CUPRA can be tted, and to nd out about
the combinations allowed between the front
axle (axle 1) and the rear axle (axle 2).
●
Never mount used tyres if you are not sure
of their “previous history”.
Tyre life
Fig.236 Location of the tyre pressure
sticker.
Correct ination pressures and sensible driving
habits will increase the useful life of your tyres.
●
Check tyre pressure at least once a month,
and also prior to any long trip.
●
The tyre pressure should only be checked
when the tyres are cold. Do not reduce the
pressure of warm tyres.
●
Adjust tyre pressure to the load being carried
by the vehicle.
●
In vehicles with a tyre pressure indicator, save
the modied tyre pressure ›››page385.
●
Avoid fast cornering and hard acceleration.
●
Inspect the tyres for irregular wear from time
to time.
Tyre pressure
The tyre pressure values are shown on the
sticker located on the rear frame of the front
left door.
Insuicient or excessive pressure greatly re-
duces the useful life of the tyres and adversely
aects vehicle performance and ride. Correct
ination pressures are very important, espe-
cially at high speeds.
The tyre pressure must be adjusted according
to the load the vehicle is carrying. If the vehicle
is going to be fully loaded, increase the tyre
pressure to the maximum load value shown on
the sticker.
Do not forget the spare wheel when checking
the tyre pressures: Keep this spare wheel ina-
ted to the highest pressure required for the
road wheels.
Wheels and tyres
377
Important information about wheels and tyres
In the case of a minimised temporary spare
wheel (125/70 R16 or 125/70 R18) inate to a
pressure of 4.2 bar as indicated on the tyre
pressure label.
Driving style
Fast cornering, heavy acceleration and hard
braking (squealing tyres) all increase tyre wear.
Wheel balance
The wheels on new vehicles are balanced.
However, certain circumstances may lead to
imbalance (run-out), which is detected as vi-
brations in the steering wheel.
Unbalanced wheels should be rebalanced, as
they otherwise cause excessive wear on steer-
ing, suspension and tyres. A wheel must also
be rebalanced when a new tyre is tted or if a
tyre is repaired.
Incorrect wheel alignment
Incorrect running gear alignment causes ex-
cessive tyre wear, impairing the safety of the
vehicle. If you notice excessive tyre wear, you
should check wheel alignment at a specialised
CUPRA Service or SEAT Oicial Service.
WARNING
Unsuitable handling of the wheels and tyres
may lead to sudden tyre pressure losses,
tread separation or even a blow-out.
●
The driver is responsible for ensuring that
all of the vehicle tyres are correctly inated
to the right pressure. The recommended tyre
pressure is indicated on the label.
●
Check tyre pressures regularly and ensure
they are kept at the indicated pressures. Tyre
pressure that is too low could cause over-
heating, resulting in tread detachment or
even burst tyres.
●
Tyre pressure should be as indicated on the
label when the tyres are cold at all times.
●
Regularly check the cold ination pressure
of the tyres. If necessary, change the tyre
pressure of the vehicle tyres while they are
cold.
●
Regularly check your tyres for damage and
wear.
●
Never exceed the speed limit or loads
specied for the type of tyre tted on your
vehicle.
For the sake of the environment
Under-inated tyres will increase fuel con-
sumption.
Tread wear indicators
Fig.237 Tyre prole: tread wear indicators.
Fig.238 Swapping tyres.
Wear indicators around 1.6mm high can be
found on the base of the original tyre treads,
ordered at regular intervals and running across
the tread ›››
Fig.237. The letters “TWI” or
triangles on the sidewall of the tyre mark the
position of the wear indicators.
378
Wheels and tyres
1)
Follow the regulations of the country you are driving in.
The minimum permitted prole depth
1)
have
been reached when the tyres have worn down
to the wear indicators. Replace the tyres with
new ones ›››
.
With a sporty driving style, check the tread
depth every 5,000 / 10,000km (3,000 /
6,000mi). When checking the tread depth,
check the wear indicators in all the tyre
grooves.
Changing wheels around
In order to wear the wheels in a uniform man-
ner, it is recommended to swap them regularly
according to the diagram ›››Fig.238. The
useful life of all the tyres will then be about the
same time.
WARNING
The tyres must be replaced at the latest when
the tread is worn down to the tread wear indi-
cators. Failure to follow this instruction could
result in an accident.
●
Particularly in diicult driving conditions
such as wet or icy roads. It is important that
the tyre tread be as deep as possible and be
approximately the same on the tyres of both
the front and the rear axles.
●
Lower driving safety due to insuicient
tread depth is particularly evident in vehicle
handling, when there is a risk of “aquaplan-
ing” in deep puddles of water and when driv-
ing through corners, and braking is also ad-
versely aected.
●
The speed has to be adapted accordingly,
otherwise there is a risk of losing control over
the vehicle.
Wheel nuts
The wheel nuts and rims have been designed
to be part of an assembly. When installing
dierent wheels (for instance alloy wheels or
wheels with winter tyres) it is important to use
the correct wheel nuts with the right length
and correctly shaped bolt heads. This ensures
that wheels are tted securely and that the
brake system functions correctly.
The wheel nuts must be clean and turn easily.
A special adapter is required to turn the anti-
theft wheel nuts ›››
page382.
WARNING
Wheel nuts should never be greased or oiled.
●
Use only wheel nuts which belong to the
wheel.
●
If the required torque of the wheel nuts is
too low, they could loosen whilst the vehicle
is in motion. Risk of accident! If the tighten-
ing torque is too high, the wheel nuts and
threads can be damaged.
NOTICE
See ›››page384 to nd out the recommen-
ded tightening torque for wheel nuts for alloy
rims.
Winter tyres
●
Winter tyres must be tted on all four
wheels.
●
Only use winter tyres that are approved for
your vehicle.
●
Please note that the maximum permissible
speed for winter tyres may be lower than for
summer tyres.
●
Also note that winter tyres are no longer ef-
fective when the tread is worn down.
●
After tting the wheels you must always
check the tyre pressures. When doing so,
take into account the correct tyre pressures
listed on the rear of the front left door frame
›››page376.
In winter road conditions winter tyres will con-
siderably improve vehicle handling. The design
of summer tyres (width, rubber compound,
tread pattern) gives less grip on ice and snow.
This applies particularly to vehicles equipped
with wide section tyres or with high speed
tyres (code letters H, V or Y on the sidewall).
Wheels and tyres
379
Important information about wheels and tyres
1)
COC = certicate of conformity.
Only use winter tyres of the correct type ap-
proved for your vehicle. The sizes of these
tyres are specied in the vehicle's documents
(e.g. EC Certicate of Conformity or COC
1)
).
The vehicle documentation varies depending
on the country of residence.
Winter tyres lose a great deal of their proper-
ties when the tread is worn down to a depth of
4mm.
The performance of winter tyres is also se-
verely impaired by ageing, even if the tread is
still much deeper than 4 mm.
A code letter indicating the speed limit is stam-
ped on all winter tyres ›››
page374.
In the infotainment system's Vehicle settings
menu, a speed warning can be set in the Tyres
menu.
Vehicles capable of exceeding these speeds
must have an appropriate sticker attached so
that it is visible to the driver. Suitable stickers
are available at specialised CUPRA Services,
SEAT Oicial Service centres and specialised
workshops. Please note the regulations to this
eect in your country.
“All-weather” tyres can also be used instead of
winter tyres.
Using winter tyres with a V-rating
Please note that the generally applicable
240km/h (149mph) speed for winter tyres
with the letter V is subject to technical restric-
tions; the maximum permissible speed for
your vehicle may be signicantly lower. The
maximum speed limit for these tyres depends
directly on the maximum axle weights for your
car and on the listed weight rating of the tyres
being used.
It is best to contact a specialised CUPRA Serv-
ice or SEAT Oicial Service to check the max-
imum speed which is permissible for the V-
rated tyres tted on your car on the basis of
this information.
WARNING
Exceeding the maximum speed permitted for
the winter tyres tted on your car can cause
tyre failure, resulting in a loss of control of
the vehicle – risk of accident.
For the sake of the environment
When winter is over, change back to summer
tyres at an appropriate moment. In tempera-
tures above +7°C (+45°F), performance will be
improved if summer tyres are used. Rolling
noise, wear and energy consumption will all
be reduced.
Snow chains
Snow chains are only permitted on the front
wheels, even on 4-wheel drive vehicles.
●
Check that they are correctly seated after
driving for a few yards; correct the position
if necessary, in accordance with the manufac-
turer's tting instructions.
●
Keep your speed below 50km/h (30 mph).
●
If there is a danger of being trapped despite
having tted the chains, it is best to disable the
traction control (TCS) in the ESC ›››page191.
Snow chains will improve braking ability as well
as traction in winter conditions.
For technical reasons, the use of snow chains
is only permitted on the following rim and tyre
combinations:
Tyres Wheel rim Chains
215/55 R17 7.5Jx17 ET40 Max. link
15mm
225/55 R17 7.5Jx17 ET40
Max. link 9
mm
225/50 R18 8x18 ET40
245/45 R18 8x18 ET40
245/40 R19 8x19 ET40
Other dimensions do not allow chains

Related Topics

Popular Owner Manuals