2024-2026 Cupra Terramar SUV Wheels and tyres -> Tyre pressure monitor system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Tyre pressure monitor system for Your Cupra Terramar SUV First Generation (2024-2026)

Wheels and tyres
385
Tyre pressure monitor system
Tightening torque of the wheel nuts
The required tightening torque for wheel nuts
for alloy rims is 140Nm.
After changing a wheel, have the tightening
torque checked immediately with a torque
wrench that is working perfectly.
The wheel nuts should be clean and turn
easily. Before tting the spare wheel, inspect
the wheel condition and hub mounting surfa-
ces. These surfaces must be clean before t-
ting the wheel.
Before checking the tightening torque, have
any rusty wheel nuts that are diicult to screw
replaced and clean the wheel hub threads.
Never apply grease or oil to wheel nuts or to
the wheel hub threads. Even if the bolts have
been tightened to the required torque, they
could come loose while driving.
Tyres with directional tread pattern
Tyres with directional tread pattern have been
designed to operate best when rotating in only
one direction. An arrow on the tyre sidewall
indicates the rotation direction on tyres with
directional tread. Always observe the indicated
rotation direction in order to guarantee opti-
mum grip and help avoid aquaplaning, exces-
sive noise and wear.
If the tyre is mounted in the opposite rotation
direction, drive with extreme caution, as the
tyre is no longer being used correctly. This is of
particular importance when the road surface
is wet. Change the tyre as soon as possible or
remount it with the correct rotation direction.
Works after changing a wheel
●
Replace the hub caps or wheel nut caps (de-
pending on equipment).
●
Return all tools to their proper storage loca-
tion.
●
If the replaced wheel does not t in the spare
wheel housing, store it safely in the luggage
compartment ›››page314.
●
Check the tyre pressure of the newly moun-
ted tyre as soon as possible.
●
In vehicles tted with a tyre pressure indi-
cator, adjust the pressure and store it in the
memory ›››page385.
●
Have the tightening torque of the wheel nuts
checked as soon as possible with a torque
wrench ›››page384. Meanwhile, drive care-
fully.
●
Have the at tyre replaced as quickly as pos-
sible.
Tyre pressure monitor sys-
tem
Tyre pressure monitor indicator
Fig.246 Instrument cluster: warning of loss
of tyre pressure.
The tyre pressure monitoring system compares
the individual speeds of each wheel and thus
the dynamic radius with the help of the ABS
sensors.
If the rolling circumference of one or more
wheels has changed, the tyre pressure moni-
toring indicator will indicate this on the instru-
ment cluster through a warning lamp and a
warning to the driver ›››
Fig.246. If only one
tyre is aected, its position on the vehicle will
be indicated.
Loss of pressure: Check left tyre pressure!
Change in wheel diameter
The wheel diameter changes when:
386
Wheels and tyres
●
Tyre pressure is changed manually.
●
The tyre pressure is insuicient.
●
The tyre's structure is damaged.
●
The vehicle is not level due to a load.
●
The wheels on an axle are subject to a heav-
ier load (e.g. with a heavy load).
●
The vehicle is tted with snow chains.
●
The temporary spare wheel has been tted.
●
One wheel has been changed on an axle.
There may be a delay in the reaction of the tyre
pressure monitoring indicator or it may not
indicate anything under certain circumstances
(e.g. sporty driving, snow-covered or unpaved
roads, or when driving with snow chains).
Calibrate the tyre pressure monitoring indi-
cator
After changing the tyre pressure or replacing
one or more wheels, the tyre pressure mon-
itoring indicator must be recalibrated. This
should also be done, for example, when swap-
ping the front and rear tyres.
It should be calibrated with the vehicle stop-
ped and its tyres cold. If calibrated while the
tyres are hot, the pressure check and calibra-
tion procedure should be repeated when cold
before the next trip.
●
Switch the ignition on.
●
Save the new ination pressure in the info-
tainment system: function button > Ve-
hicle > Exterior > Tyres ›››page41.
●
OR: > Vehicle > Status > Tyres.
After storing the new ination pressure, a con-
rmation message will be displayed, the warn-
ing light in the instrument cluster will ash
briey and a driver alert tone will be played.
The tyre pressure loss indicator uses the ABS
sensors to compare the turns of each wheel
and, therefore, their tread circumferences,
among other aspects. The set values are col-
lected and monitored after a long journey at
dierent speeds.
For example, if the wheels are under very
heavy loads, the tyre pressure must be in-
creased to the total recommended tyre pres-
sure before calibration ›››Fig.246.
WARNING
If the tyres are inated to dierent pressures,
or to a pressure that is too low, a tyre may be
damaged and control of the vehicle may be
lost. This could lead to a serious or even fatal
accident.
●
If the lamp lights up, reduce speed im-
mediately and avoid any sudden turning or
braking manoeuvres. Stop as soon as possi-
ble, and check the pressure and status of all
tyres.
●
The tyre pressure loss indicator only works
correctly if all the tyres are at the correct
pressure when cold, and it is subsequently
calibrated according to the described proce-
dure.
●
If the tyres have no punctures and do not
need to be replaced immediately, drive to the
nearest specialist workshop at low speed and
have the tyre pressure checked and correc-
ted.
Note
●
When driving for the rst time with new
tyres at high speeds, the tyres may expand
slightly, which may result in an air pressure
warning.
●
If a low tyre pressure is detected when the
ignition is switched on, an audible warning
will sound. If the system fails, an audible sig-
nal sounds.
●
Driving on unpaved roads for a long pe-
riod of time, or sporty driving, may tempora-
rily deactivate the system. The warning lamp
shows a fault, but disappears when road con-
ditions or driving behaviour change.
●
Do not only rely on the tyre pressure mon-
itoring system. Check the tyres regularly to
ensure that the tyre pressures are correct
and that the tyres are free of damage such as
punctures, cuts, gouges and dents. Remove
any non-puncturing objects from the tyres.

Related Topics

Popular Owner Manuals