2024-2026 Cupra Terramar SUV Wheels and tyres -> Changing a wheel User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Changing a wheel for Your Cupra Terramar SUV First Generation (2024-2026)

380
Wheels and tyres
Remove any central wheel trims before tting
snow chains.
WARNING
The use of unsuitable or incorrectly tted
chains could lead to serious accidents and
damage.
●
Always use appropriate snow chains.
●
Observe the tting instructions provided
by the snow chain manufacturer.
●
Never exceed the speed limits when driving
with snow chains.
●
Before tting the chains, check that the
wheel/tyre combination on the table is the
one installed on your vehicle. The combina-
tion can also be found on the technical data-
sheet.
NOTICE
●
Remove the snow chains to drive on roads
without snow. Otherwise they will impair ve-
hicle handling, damage the tyres and wear
out very quickly.
●
Wheel rims may be damaged or scratched
if the chains come into direct contact with
them. CUPRA recommends the use of coated
snow chains.
Changing a wheel
Introduction
Only change a wheel yourself if you are famil-
iar with the necessary operations and safety
measures, if you have the necessary tools and
if the vehicle is parked safely.
Preliminary actions
●
Stop the vehicle on a level surface and in a
safe place, as far away from road traic as pos-
sible.
●
Apply the electronic parking brake.
●
Switch on the hazard warning lights.
●
Automatic transmission: switch on the park-
ing lock P.
●
If towing a trailer, unhitch the trailer from
your vehicle.
●
Lay out the on-board tools ›››page338 and
the wheel to be changed.
●
Follow the legal provisions of each country
(reective vest, warning triangles, light beacon,
etc.).
●
Get all occupants out of the vehicle and
keep them out of the danger zone (e.g. behind
the guard rail).
WARNING
●
Always observe the above steps and pro-
tect yourself and other road users.
●
If you change the wheel on a slope, block
the wheel on the opposite side of the car
with a stone or similar to prevent the vehicle
from moving.
Location and use of the temporary
spare wheel
Fig.239 In the luggage compartment: load
oor raised.
382
Wheels and tyres
Wheel nut caps
Fig.241 Wheel: wheel nuts with caps.
Removal
●
Fit the plastic clip (vehicle tools ›››Fig.205)
over the cap until it clicks into place
›››Fig.241.
●
Remove the cap with the plastic clip.
The caps protect the wheel nuts and should be
remounted after changing the tyre.
The anti-theft wheel locking bolt has a spe-
cial cap. This only ts on anti-theft locking
bolts and is not for use with standard wheel
nuts.
Anti-theft wheel nuts
Fig.242 Anti-theft wheel nut with cap and
adapter.
Loosening the anti-theft wheel nut
●
Remove the wheel trim or hub cap.
●
Insert the special adapter ›››Fig.242
1
(vehicle tools ›››
page338) onto the anti-theft
wheel nut and push it on as far as it will go.
●
Insert the wheel wrench (vehicle tools) onto
the adapter as far as it will go.
●
Remove the wheel nut ›››page382.
Note
Make a note of the code number of the anti-
theft wheel nut and keep it in a safe place,
but not in your vehicle. If you need a new
adapter, you can obtain it from the special-
ised CUPRA service or the SEAT Oicial Serv-
ice, by giving the code number.
Loosening wheel nuts
Fig.243 Tyre change: loosen the wheel
nuts.
Use only the wheel wrench belonging to the
car to loosen the wheel nuts.
Loosen the wheel nuts only about one turn
before raising the vehicle with the jack.
If the wheel nut is very tight, carefully push on
the end of the wheel wrench with your foot.
Hold on to the vehicle for support and take
care not to slip during this operation.
Loosening wheel nuts
●
Fit the box spanner into the bolt as far as it
will go ›››Fig.243.
●
Hold the wrench at the end and rotate
the bolt approximately one turn anticlock-
wise››› .
Wheels and tyres
383
Changing a wheel
Important information about wheel nuts
Factory-tted rims and wheel nuts are specially
matched during construction. Therefore, if dif-
ferent rims are tted, the correct wheel nuts
with the right length and heads must be used.
This ensures that wheels are tted securely
and that the brake system functions correctly.
In certain circumstances, you should not even
use wheel nuts from vehicles of the same
model.
WARNING
If the wheel nuts are not properly tightened,
they could come loose while driving and
cause an accident, serious injury and loss of
vehicle control.
●
Use only wheel nuts which correspond to
the rim in question.
●
Never use dierent wheel nuts.
●
Wheel nuts and threads should be clean,
free of oil and grease, and it should be possi-
ble to screw them easily.
●
To loosen and tighten wheel nuts, only use
the wheel wrench that came with the car
from the factory.
●
The wheel nuts should only be loosened
slightly (about one turn) before raising the
vehicle with the jack. Risk of accident!
●
Never apply grease or oil to wheel nuts or
to the wheel hub threads. Even if the bolts
have been tightened to the required torque,
they could come loose while driving.
●
Never loosen the screwed joints of wheel
rims with bolted ring trims.
●
If wheel nuts are tightened below the re-
quired torque, the bolts and rims could come
loose while driving. If tightening torque is too
high, the wheel nuts or threads can be dam-
aged.
Raise the vehicle
Fig.244 Jack position points.
Fig.245 Crossbar: mounting the jack on
the vehicle.
●
Rest the jack (vehicles tools) on rm ground.
If necessary use a large, strong board or similar
support. If the surface is slippery (for example
tiles) place the jack on a rubber mat or similar
to prevent it from slipping ››› .
●
Look on the crossbar for the mark of the
jack support point (sunken area) closest to the
wheel to be changed ›››Fig.244.
●
Turn the jack crank handle, located below
the crossbar support point, to raise it until the
tab
1
›››
Fig.245 is below the housing that is
provided.
●
Align the jack so that the tab
1
“grips”
onto the housing provided on the cross mem-
ber and the mobile base
2
is resting on the
ground. The base plate
2
should fall vertically
with respect to the support point
1
.
●
Continue turning the jack until the wheel is
slightly lifted o the ground.
384
Wheels and tyres
WARNING
The factory-supplied jack is only designed
for changing wheels on this model. On no
account attempt to use it for lifting heavier
vehicles or other loads. Risk of injury.
●
Make sure the jack remains stable. If the
surface is slippery or soft, the jack could slip
or sink, respectively, with the consequent
risk of causing injuries.
●
Lift the vehicle using only the jack supplied
from the factory. Other jacks, even those ap-
proved for other CUPRA models could slip,
with the consequent risk of injury.
●
Place the jack only at the support points
provided on the crossbar and align it. Other-
wise, the jack could slip because it does not
have suicient grip on the vehicle. Risk of
injury!
●
You should never place a body limb such as
an arm or leg under a raised vehicle that is
solely supported by the jack.
●
If you have to work underneath the vehi-
cle, you must use suitable stands additionally
to support the vehicle. Accident risk!.
●
Never raise the vehicle if it is tilting to one
side or the engine is running.
●
Never start the engine when the vehicle is
raised. The vehicle may come loose from the
jack due to the engine vibrations.
NOTICE
●
The vehicle must not be raised on the
crossbar. Place the jack only at the support
points provided on the crossbar and align it.
Otherwise, the vehicle may be damaged.
●
Any type of load or weight applied to the
external trim/door (treading on it, tting the
jack, resting heavy objects, etc.) can cause
damage to it. CUPRA accepts no responsibil-
ity for any damages caused by improper use
of the external trim or body.
Removing and installing a wheel
Change the wheel after loosening the wheel
nuts and raising the vehicle with the jack.
When removing/tting the wheel, the rim may
hit and damage the brake disc. Therefore,
please take care and get a second person to
assist you.
Taking o the wheel
●
Unscrew the nuts with the wheel wrench and
place them on a clean surface.
●
Remove the wheel.
Putting on the spare wheel
Check the rotation direction of the tyre
›››
page385.
●
Place the spare wheel or temporary spare
wheel into position.
●
Screw in the wheel nuts and tighten them a
little with the wheel wrench.
●
Use the appropriate adapter to tighten the
anti-theft wheel nuts.
●
Carefully lower the vehicle using the jack.
●
Use the wheel wrench to tighten all of the
wheel nuts clockwise. Tighten the bolts in di-
agonal pairs (not in a circle).
●
Put the caps, trim or full hubcap back on.
Fitting the minimised spare wheel (depend-
ing on the version)
For technical reasons (brake disc size), it may
not be possible to t the minimised spare
wheel on the front axle.
In the event of a puncture or damage to a front
tyre, follow the instructions below:
1. Remove the rear wheel on the same side
as the damaged front wheel.
2. Fit the minimised spare wheel on the rear
axle.
3. Replace the damaged front wheel with the
removed rear wheel.
If necessary, check that the tyre pressures are
correct as soon as possible.

Related Topics

Popular Owner Manuals