Advertisement

Advertisement

Getting To Know Your Vehicle -> Electric Vehicle App for Your Fiat 500 E 4 Door Second Generation (2020-2024)

GETTING TO KNOW YOUR VEHICLE 23  
ELECTRIC VEHICLE APP  
Within the Uconnect system is the Electric Vehicle  
App that allows you to see your vehicle’s power flow  
and set a charging schedule for your vehicle’s high  
voltage battery. To access this App, press the Apps  
or Vehicle button on the main menu bar of the  
radio’s touchscreen, and locate the Electric Vehicle  
App. Accessing the app brings you to a set of three  
pages: Power Flow, Schedules, and Charge Setting.  
2
Schedules Screen  
Power Flow Screen  
2. Select the schedule to be set (1, 2, or 3) by  
pressing the appropriate arrow on the right side  
of the screen.  
Driving History  
The Driving History screen shows the miles (km) driven  
in Full Electric kWh (battery powered) mode for both  
the previous week and the current week. The data is  
displayed in a bar graph: Electric mode in teal.  
3. Select what time Scheduled Charging should start  
and stop charging or select “Charge Until Full”. If  
“Charge Until Full” is selected a stop charging time  
cannot be selected.  
4. Set the Charge Start Time: Hours, Minutes, and  
AM/PM.  
Electric Vehicle App Location  
NOTE:  
Power Flow  
This is to occur every week (as long as the vehicle  
is connected to an EVSE).  
The Power Flow screen shows the current power  
readings for all of the following:  
Driving History Screen  
Motor - Shows the amount of power (in kW) the high  
voltage battery is currently providing/absorbing.  
Charging Schedule  
Climate - Shows the amount of power (in kW) the  
Climate Control system is using to maintain the  
current interior temperature.  
To set a charging schedule, select the Electric Vehicle  
App in the touchscreen and follow these steps:  
1. Select “Schedules”.  
Power Flow paths are indicated by the direction of the  
arrows on the touchscreen.  
Set Charge Schedule  
24 GETTING TO KNOW YOUR VEHICLE  
charging schedule start time and estimated time  
to charge the battery to 100%. If within one hour  
of selecting “Yes,” the vehicle is connected to a  
powered EVSE, the vehicle will immediately begin  
to charge (temporarily ignoring any set charge  
schedule). To fully deactivate the charge schedule,  
refer to the “Schedules” feature within the Electric  
Vehicle App.  
5. When done, press the Back Arrow in the upper  
right hand corner, then select “yes” to save the  
charge schedule. The active schedule will be  
indicated by the check mark to the right of the  
schedule event line. The event action and time will  
be displayed.  
6. To add another Scheduled Charging event, repeat  
these steps.  
The charging schedule can also be overridden if an  
EVSE is plugged in, unplugged, and then plugged in  
a second time to the vehicle. This “double  
plug sequence” will override the schedule that is set  
in the radio, and begin charging the vehicle  
immediately. The double plug sequence must be  
completed within 10 seconds for it to override the  
programmed schedule.  
Charge Setting Screen  
NOTE:  
The Charge Setting can be adjusted by selecting one of  
the levels 1 through 5, with 1 being the slowest rate of  
charge and 5 being the fastest. The display also shows  
information related to:  
A maximum of three independent Scheduled  
Charging events can be scheduled at a given time.  
NOTE:  
Battery Level — Indicates, in percentage, the high-  
voltage battery SOC.  
If the charging schedule is not enabled, the vehicle  
will charge whenever plugged in. It is not necessary  
to set up the charging schedule to charge the  
vehicle.  
If “Charge Until Full” is selected, and the vehicle is  
plugged in after the start time of the schedule, the  
vehicle will start charging when it reaches the start  
time the next day. If you would like to begin charging  
immediately, and continue charging until the vehicle  
is fully charged, you can select the “Charge Now”  
option or use the double plug override option.  
Estimate time to 100% — Corresponds to the time  
required to obtain full recharging of the high-voltage  
battery.  
If the vehicle is plugged in outside of the charging  
schedule set in the Uconnect system (and Charge  
Until Full is not selected), the vehicle’s battery will  
not charge. Charging will only begin immediately if  
the vehicle is plugged in within the time and day of  
the week set in the schedule. Otherwise, charging  
will automatically begin when the selected charge  
time/day of the week occurs or whenever the vehicle  
is plugged in with no charge schedule set.  
NOTE:  
The Charge Setting will be saved each time the  
vehicle is turned off, then back on again.  
NOTE:  
For information on jump starting your vehicle  
page 173.  
For information on jump starting your vehicle,  
173.  
page  
ð
ð
AC Charging Level— If Equipped  
KEYS  
If the vehicle is turned off outside of the charging  
window, a radio pop-up message will be displayed,  
which provides an option to begin charging the  
vehicle immediately. The pop-up message asks  
the driver if they would like to “Charge Now?” and  
provides other information, including the next  
The fourth screen within the Electric Pages App is the  
AC Charging Level screen. From this screen, you can  
select the rate at which your vehicle charges. Rate  
selections 1 (low rate of charge) through 5 (high rate  
of charge) are available. The lower the selected rate,  
the longer it will take for your vehicle to reach a full  
charge.  
KEY FOB  
Your vehicle is equipped with a key fob which supports  
Passive Entry, Remote Keyless Entry (RKE) and Keyless  
Enter ‘n Go™. The key fob allows you to lock or unlock