Get Getting To Know Your Vehicle -> Exterior Lights Guide for Fiat 500 E 4 Door Second Generation (2020-2024)

38 GETTING TO KNOW YOUR VEHICLE

WARNING!

HEATED MIRRORS — IF EQUIPPED

These mirrors are heated to melt frost or

ice. This feature will be activated whenever

you turn on the rear window defroster (if

Vehicles and other objects seen in the passenger

side convex mirror will look smaller and farther

away than they really are. Relying too much on your

passenger side convex mirror could cause you to

collide with another vehicle or other object. Use your

inside mirror when judging the size or distance of a

vehicle seen in the passenger side convex mirror.

equipped)

page 43.

EXTERIOR LIGHTS

MULTIFUNCTION LEVER

POWER MIRRORS

The power mirror switch is located on the driver’s door

trim panel.

The multifunction lever, located on the left side of the

steering wheel. The multifunction lever controls the

operation of the headlights, parking lights, turn signals,

headlight beam selection, and the passing lights.

Power Mirror Switch

1 — Mirror Selector Switch

2 — Mirror Adjustment Switch

To adjust the mirror, rotate the mirror selection switch

to the left or to the right and then push the mirror

adjustment switch in the four directions indicated by

arrows.

NOTE:

FOLDING MIRRORS

The headlights can only be turned on with the ignition

in the ON/RUN position.

The exterior mirrors are hinged to allow the mirror to

pivot forward or rearward to help avoid damage. The

mirror can be fold manually from the open position to

the closed postion.

NOTE:

● To adjust the power mirrors, the ignition must be in

the ON/RUN position.

● Once the mirror is adjusted, rotate the control to the

neutral position to avoid accidental movements.

● The power mirror switches will remain active for up

to three minutes after the ignition is placed in the

OFF position. Opening either front door will cancel

this feature.

Multifunction lever

Folding Exterior Mirror

GETTING TO KNOW YOUR VEHICLE 39

lever forward (toward the front of the vehicle), and

an indicator will illuminate in the instrument cluster

display. The headlights must be in the ON position.

DAYTIME RUNNING LIGHTS

The Daytime Running Lights (DRLs) are activated

with the switch in the AUTO position and in daylight

conditions.

To deactivate the high beam headlights, pull the

multifunction lever rearward (toward the rear of the

vehicle).

NOTE:

With the ignition system in the ON/RUN position and

the propulsion system not active, the daytime running

lights are switched off.

AUTOMATIC HIGH BEAM HEADLAMP CONTROL

— IF EQUIPPED

In order not to dazzle other road users, the lights

are automatically deactivated when approaching cars

travelling in the opposite direction or when following a

car travelling in the same direction.

NOTE:

On some vehicles, the Daytime Running Lights may

deactivate or reduce intensity on one side of the vehicle

(when a turn signal is activated on that side), or on both

sides of the vehicle (when the hazard warning lights are

activated).

Multifunction lever (Vehicles Sold In Canada Only)

HEADLIGHTS

NOTE:

To turn on the headlights, rotate the end of the

● The Automatic High Beam Headlamp Control can

be turned on or off by selecting “ON” under “Auto

multifunction lever to the headlight position. When the

headlight switch is on, the parking lights, taillights,

license plate light, and instrument panel lights are also

turned on. To turn off the headlights, rotate the end of

the multifunction lever back to the O (off) position.

AUTOMATIC LIGHTING CONTROL (AUTOLIGHT)

— DUSK SENSOR

The light sensor is equipped with an infrared LED,

located on the windshield. It detects changes in light

intensity outside the vehicle, based on the sensitivity

of light set by using the menu on the display or on the

Uconnect system.

Dim High Beams” within your Uconnect Settings

page 113, as well as turning the headlight switch to

the AUTO position.

● Broken, muddy, or obstructed headlights and

taillights of vehicles in the field of view will cause

headlights to remain on longer (closer to the

vehicle). Also, dirt, film, and other obstructions on

the windshield or camera lens will cause the system

to function improperly.

NOTE:

On vehicles sold in Canada, the rear parking lights, and

Daytime Running Lights (DRLs) will turn on when the

headlight switch is rotated to the O (off) position.

The higher the sensitivity, the lesser the amount of

external light required for controlling the lighting.

AUTOMATIC HEADLIGHTS

With the ignition system in the ON/RUN position,

rotate the switch to the AUTO position to activate the

"Automatic lighting control" function.

● If the windshield or Automatic High Beam Headlamp

Control mirror is replaced, the mirror must be re-

aimed to ensure proper performance. See a local

authorized dealer.

This system automatically turns the headlights on or off

according to ambient light levels. To turn the system on,

with the engine running, rotate the headlight switch to

the AUTO position.

HIGH BEAMS

To activate the high beam headlights, with the ignition

system in the ON/RUN position, push the multifunction

To turn the automatic headlights off, turn the headlight

switch out of the AUTO position.

40 GETTING TO KNOW YOUR VEHICLE

NOTE:

FLASH-TO-PASS

TURN SIGNALS

The lights must be turned off within two minutes of

placing the ignition in the OFF position to activate this

feature.

You can signal another vehicle with your headlights by

lightly pulling the multifunction lever toward you. This

will cause the high beam headlights to turn on, and

remain on, until the lever is released.

Push the multifunction lever upward to signal a

right turn or downward to signal a left turn. The

corresponding indicator in the instrument cluster

display will blink to indicate the operation of the turn

signal.

REAR FOG LIGHTS

The fog light switch is located on the instrument panel

to the left just below the steering wheel.

PARKING LIGHTS

NOTE:

The indicators will automatically turn off when the turn

has been completed and the steering wheel is returned

to a straight position.

With the ignition system turned to the OFF position,

rotating the switch from the AUTO position to the

Parking Lights will light up the side/tail lights and

number plate lights.

LANE CHANGE ASSIST

The parking light indicator in the cluster will illuminate.

If you wish to signal a lane change, place the

multifunction lever in the unstable position for less than

half a second.

FOLLOW ME HOME/HEADLIGHT DELAY

When this feature is selected, the driver can choose to

have the headlights remain on for a preset period of

time.

The turn signal will flash five times then automatically

turn off.

Headlight Delay Activation

INTERIOR LIGHTS

Rear Fog Light Switch

To activate the delay feature, place the ignition in the

OFF position while the headlights are still on. Then, turn

off the headlights within two minutes. The delay interval

begins when the headlight switch is turned off.

To activate the rear fog lights, push the button switch.

To turn off the rear fog lights, push the button switch a

second time.

FRONT COURTESY LIGHT

The courtesy lights will automatically turn on when the

door is open or closed.

Headlight Delay Deactivation

NOTE:

To turn on the rear fog lights, the low beam headlights

must first be active.

The feature is disabled by turning on the headlights, the

parking lights or by placing the ignition in the ON/RUN

position.

An indicator light in the instrument cluster illuminates

when the fog lights are turned on.

If you shut off the lights before the ignition is turned on,

they will turn off in the normal manner.

Getting To Know Your Vehicle -> Exterior Lights for Your Fiat 500 E 4 Door Second Generation (2020-2024)

Related Topics

Getting To Know Your Vehicle

Getting To Know Your Instrument Panel

Popular Owner Manuals

Latest Owner Manuals