Get Convenient features -> Exterior lights Guide for Hyundai I20 4 Door 2021-2026

Convenient features

EXTERIOR LIGHTS

Lighting control

OBC3050029

$872ꢀOLJKWꢀSRVLWLRQꢀꢁLIꢀHTXLSSHGꢂ

OPDE046065

When the light switch is in the AUTO

position, the position light and headlight

will be turned ON or OFF automatically

depending on the amount of light

outside the vehicle.

Even with the AUTO light feature

in operation, it is recommended to

manually turn ON the lights when driving

at night or in a fog, or when you enter

dark areas, such as tunnels and parking

facilities.

To operate the lights, turn the knob at

the end of the control lever to one of the

following positions:

(1) OFF (O) position

(2) AUTO light position (if equipped)

(3) Position light position

(4) Headlight position

NOTICE

śꢀ 'RꢀQRWꢀFRYHUꢀRUꢀVSLOOꢀDQ\WKLQJꢀRQꢀWKHꢀ

sensor (1) located on the instrument

panel.

śꢀ 'RꢀQRWꢀFOHDQꢀWKHꢀVHQVRUꢀXVLQJꢀ

a window cleaner, the cleanser

may leave a light film which could

interfere with sensor operation.

śꢀ ,Iꢀ\RXUꢀYHKLFOHꢀKDVꢀZLQGRZꢀWLQWꢀRUꢀ

other types of metallic coating on

the front windscreen, the AUTO light

system may not work properly.

5-42

05

High beam operation

OAE046469L

OAE046453L

Position light position (

)

To turn on the high beam headlight,

push the lever away from you.

The high beam indicator will light when

the headlight high beams are switched

on.

The position light, license plate light and

instrument panel light are turned ON.

To turn off the high beam headlight, pull

the lever towards you. The low beams

will turn on.

WARNING

Do not use high beam when there are

other vehicles approaching you. Using

high beam could obstruct the other

driver’s vision.

OAE046467L

+HDGOLJKWꢀSRVLWLRQꢀꢁ

)

The headlight, position light, license

plate light and instrument panel light are

turned ON.

Information

7KHꢀLJQLWLRQꢀVZLWFKꢀPXVWꢀEHꢀLQꢀWKHꢀ21ꢀ

i

position to turn on the headlight.

5-43

Convenient features

Turn signals and lane change

signals

OAE046455L

To flash the high beam headlight, pull

the lever towards you, then release the

lever. The high beams will remain ON as

long as you hold the lever towards you.

OTLE045284

To signal a turn, push down on the lever

for a left turn or up for a right turn in

position (A). To signal a lane change,

move the turn signal lever slightly and

hold it in position (B).

The lever will return to the OFF position

when released or when the turn is

completed.

If an indicator stays on and does not

flash or if it flashes abnormally, one of

the turn signal bulbs may be burned out

and will require replacement.

2QHꢃWRXFKꢀWXUQꢀVLJQDOꢀIXQFWLRQꢀ

To activate a one-touch turn signal

function, move the turn signal lever

slightly and then release it. The lane

change signals will blink 3, 5 or 7 times.

You can activate or deactivate the One

Touch Turn Signal function or choose

the number of blinks (3, 5, or 7) from the

User Settings Mode on the LCD display.

)RUꢀPRUHꢀGHWDLOVꢁꢀUHIHUꢀWRꢀŕ/&'ꢀ'LVSOD\ꢀ

0RGHVŖꢀLQꢀFKDSWHUꢀꢂꢃꢀꢀ

5-44

05

Front fog light (if equipped)

Rear fog light

OPDE046064

OPDE046066

To turn on the rear fog lamp:

Fog lamps are used to provide improved

visibility when visibility is poor due to

fog, rain or snow, etc. Use the switch

next to the headlamp switch to turn the

fog lamps ON and OFF.

1. Turn on the position lamp.

2. Turn the light switch (1) to the front

fog lamp position.

3. To turn off the front fog lamp, turn

the light switch to the front fog lamp

position again or turn off the position

lamp.

Position the light switch in the position

lamp position, turn the light switch (1)

to the front fog lamp position, and then

turn the light switch (1) to the rear fog

lamp position.

To turn the rear fog lamps off, do one of

the following:

śꢀ Turn off the position light switch.

śꢀ Turn the light switch to the rear fog

lamp position again.

śꢀ When the light switch is in the position

lamp position, if you turn off the front

fog lamp, the rear fog lamp will also

turn off.

NOTICE

When in operation, the fog lights

consume large amounts of vehicle

electrical power. Only use the fog lights

when visibility is poor.

5-45

Convenient features

Battery saver function

The purpose of this feature is to prevent

the battery from being discharged.

The system automatically turns off the

position lamp when the driver turns the

engine off and opens the driver-side

door.

With this feature, the position lamps will

turn off automatically if the driver parks

on the side of road at night.

OAC3059027TU

If necessary, to keep the lamps on when

the engine is turned off, perform the

following:

Vehicle without front fog lamp

To turn on the rear fog lamp:

1) Open the driver-side door.

Position the light switch in the headlamp

position, and then turn the light switch

(1) to the rear fog lamp position.

To turn the rear fog lamps off, do one of

the following:

śꢀ Turn off the headlamp switch.

śꢀ Turn the light switch to the rear fog

2) Turn the position lamps OFF and ON

again using the light switch on the

steering column.

Headlamps delay function

(if equipped)

If you place the ignition switch in the

ACC or OFF position with the headlamps

ON, the headlamps (and/or position

lamps) remain on for about 5 minutes.

However, with the engine off if the

GULYHUŔVꢀGRRUꢀLVꢀRSHQHGꢀDQGꢀFORVHGꢁꢀWKHꢀ

headlamps (and/or position lamps) are

turned off after 15 seconds.

lamp position again.

The headlamps (and/or position lamps)

can be turned off by pressing the lock

button on the remote key or smart

key twice or turning the light switch to

the OFF or AUTO position. However, if

you turn the light switch to the AUTO

position when it is dark outside, the

headlamps will not be turned off.

5-46

05

NOTICE

Headlight levelling device

If the driver exits the vehicle through

another door besides the driver

door, the battery saver function

does not operate and the headlight

GHOD\ꢀIXQFWLRQꢀGRHVꢀQRWꢀWXUQꢀ2))ꢀ

automatically.

This may cause the battery to

discharge. To avoid battery discharge,

WXUQꢀ2))ꢀWKHꢀKHDGOLJKWVꢀPDQXDOO\ꢀIURPꢀ

the headlight switch before exiting the

vehicle.

OBC3050009R

Daytime running light (DRL)

(if equipped)

The Daytime Running Lights (DRL) can

make it easier for others to see the front

of your vehicle during the day, especially

after dawn and before sunset.

The DRL system will turn the dedicated

light OFF when:

1. The parking brake is applied.

2. The engine is turned off.

To adjust the headlight beam level

according to the number of the

passengers and loading weight in the

luggage area, turn the beam levelling

switch.

The higher the number on the switch

position, the lower the headlight beam

level. Always keep the headlight beam

at the proper levelling position, or

headlights may dazzle other road users.

Listed below are examples of

appropriate switch settings for varying

loads. For loading conditions other than

those listed, adjust the switch position to

the most similar situation.

Switch position

Loading condition

0

Driver only

Driver + Front

passenger

0

1

Full passengers

(including driver)

Full passengers

(including driver) +

Maximum permissible

loading

2

3

Driver + Maximum

permissible loading

5-47

Convenient features

WARNING

If the function does not work properly,

we recommend that the system be

inspected by a HYUNDAI authorised

repairer. Do not attempt to inspect or

replace the wiring yourself.

Low Beam Assist-Static light

Whilst driving a corner, for greater

visibility and safety, either the left or

right side Low Beam Assist-Static light

will turn on automatically. The Low

Beam Assist-Static light will turn on

when one of the following conditions

occurs.

śꢀ Vehicle speed is less than 6 mph (10

km/h) and steering wheel angle is

turned approximately 80 degrees with

the low beam on.

śꢀ Vehicle speed is between 6 mph

(10 km/h) to 56 mph (90 km/h)

and steering wheel angle is turned

approximately 35 degrees with the low

beam on.

śꢀ When the vehicle is in reverse with

one of the conditions above satisfied,

the light opposite to the direction the

steering wheel is turned will turn on.

5-48

05

+,*+ꢀ%($0ꢀ$66,67ꢀǣ+%$Ǥꢀǣ,)ꢀ(48,33('Ǥ

)XQFWLRQꢀVHWWLQJ

The driver can activate HBA by placing

the ignition switch to the ON position

and by selecting: ‘User Settings ꢀ

Lights ꢀꢀ+%$ꢀꢂ+LJKꢀ%HDPꢀ$VVLVWꢃŔꢄꢀ,Iꢀ\RXꢀ

disable this setting, HBA will not work.

The setting of HBA will be maintained, as

selected, when the engine is re-started.

OPDE046057

Operating condition

High Beam Assist is a system that

automatically adjusts the headlight

range (switches between high beam and

low beam) according to the brightness

of other vehicles and road conditions.

1. Place the light switch in the AUTO

position.

2. Turn on the high beam by pushing the

lever away from you.

3. High Beam Assist ( ) indicator will

illuminate.

4.High Beam Assist will turn on when

vehicle speed is above 25 mph (40

km/h).

Detecting sensor

(Front view camera)

OBC3070001

[1] : Front view camera

The front view camera is used as a

detecting sensor to detect ambient light

and brightness whilst driving.

Refer to the picture above for the

detailed location of the detecting sensor.

NOTICE

good condition to maintain optimal

performance of High Beam Assist.

)RUꢀPRUHꢀGHWDLOVꢀRQꢀWKHꢀSUHFDXWLRQVꢀ

of the front view camera, refer to

ŕ)RUZDUGꢀ&ROOLVLRQꢄ$YRLGDQFHꢀ$VVLVWꢀ

ꢅ)&$ꢆŖꢀVHFWLRQꢀLQꢀFKDSWHUꢀꢇꢃꢀ

5-49

Convenient features

- If the light switch is pushed away

when High Beam Assist is operating,

High Beam Assist will turn off.

- If the light switch is pulled towards

you when the high beam is off, the

high beam will turn on. When you let

go of the light switch, the lever will

move to the middle and the high beam

will turn off.

System malfunction and

limitations

System malfunction

- If the light switch is pulled towards

you when the high beam is on by High

Beam Assist, and High Beam Assist

will turn off.

- If the light switch is placed to the

headlight position ( ), High Beam

Assist will turn off and the low beam

will be on continuously.

OTM050218L

When High Beam Assist is not working

properly, the warning message will come

on for a few seconds. After the message

disappears, the master warning light

When High Beam Assist is operating, the

high beam switches to low beam in the

following conditions.

- When the headlight of an on-coming

vehicle is detected.

- When the tail light of a vehicle in front

is detected.

- When the headlight or tail light of a

motorcycle or a bicycle is detected.

- When the surrounding ambient light is

bright enough that high beams are not

required.

- When streetlights or other lights are

detected.

- When the light switch is not in the

AUTO position.

- When High Beam Assist is off.

(

) will illuminate.

We recommend that you take your

vehicle to a HYUNDAI authorised

repairer and have the system checked.

CAUTION

The system may not operate normally if

any of the following conditions should

occur:

1. When the illumination from an

on-coming vehicle or a vehicle in

front is dim. Such examples may

include:

śꢀ When the headlights of an oncoming

vehicle or the tail lights of a vehicle

in front is covered with dust, snow,

or water

śꢀ When the headlights on an

RQꢄFRPLQJꢀYHKLFOHꢀDUHꢀ2))ꢁꢀEXWꢀWKHꢀ

fog lights are ON)

- When the vehicle speed is below 19

mph (30 km/h).

5-50

05

2. When the front view camera is

adversely affected by an external

condition. Such examples may

include:

śꢀ When the vehicle’s headlights have

been damaged or not repaired

properly

śꢀ When the vehicle headlights are not

aimed properly

śꢀ When the vehicle is driven on a

narrow curved road or rough road

śꢀ When the vehicle is driven on an

uphill road or downhill road

śꢀ When only part of the vehicle in front

is visible on a crossroad or curved

road

śꢀ When there is a traffic light,

reflecting sign, flashing sign or mirror

śꢀ When the road conditions are bad

such as being wet or covered with

snow

WARNING

śꢀ 7KHꢀIXQFWLRQꢀPD\ꢀQRWꢀZRUNꢀDURXQGꢀꢈꢉꢀ

seconds after starting the vehicle or

the initialization or rebooting of the

front view camera.

śꢀ 'RꢀQRWꢀDWWHPSWꢀWRꢀGLVDVVHPEOHꢀ

the front view camera without the

assistance of a HYUNDAI authorised

repairer technician.

If the front view camera is removed

for any reason, the system may need

to be re-calibrated. We recommend

that the system be inspected by a

HYUNDAI authorised repairer.

śꢀ ,IꢀWKHꢀZLQGVFUHHQꢀRIꢀ\RXUꢀYHKLFOHꢀ

is replaced, most likely the front

view camera will need to be

re-calibrated. If this occurs, have

your vehicle inspected and have the

system re-calibrated by a HYUNDAI

authorised repairer.

śꢀ %HꢀFDUHIXOꢀWKDWꢀZDWHUꢀGRHVQŔWꢀJHWꢀLQWRꢀ

front view camera unit and do not

remove or damage related parts of

High Beam Assist system.

śꢀ 'RꢀQRWꢀSODFHꢀREMHFWVꢀRQꢀWKHꢀFUDVKꢀ

pad that reflect light such as mirrors,

white paper, etc. The system may

malfunction if sunlight is reflected.

śꢀ $WꢀWLPHVꢁꢀ+LJKꢀ%HDPꢀ$VVLVWꢀPD\ꢀ

not work properly. The system is

for your convenience only. It is the

responsibility of the driver for safe

driving practices and always check

the road conditions for your safety.

śꢀ When a vehicle suddenly appears

from a curve

śꢀ When the vehicle is tilted from a flat

tyre or being towed

śꢀ :KHQꢀ/DQHꢀ.HHSLQJꢀ$VVLVWꢀV\VWHPꢀ

warning light illuminates

śꢀ When the light from the oncoming or

front vehicle is not detected because

of exhaust fume, smoke, fog, snow,

etc.

śꢀ When the front window is covered

with foreign matters such as ice,

dust, fog, or is damaged

3. When the forward visibility is poor.

Such examples may include:

śꢀ When the headlights of an oncoming

vehicle or a vehicle in front is not

detected due to poor outside

visibility (smog, smoke, dust, fog,

heavy rain, snow, etc.)

śꢀ :KHQꢀWKHꢀV\VWHPꢀGRHVꢀQRWꢀRSHUDWHꢀ

normally, change the light position

manually between the high beam and

low beam.

śꢀ When the windscreen visibility is

poor

5-51

Convenient features -> Exterior lights for Your Hyundai I20 4 Door 2021-2026

Related Topics

Convenient features

Popular Owner Manuals

Latest Owner Manuals