Get Features of your vehicle Guide for Hyundai I30 4 Door Third Generation (2016-2026)

Keys / 4-2

Remote keyless entry / 4-4

Theft-alarm system / 4-6

Door locks / 4-8

Tailgate / 4-12

Windows / 4-14

Bonnet / 4-19

Fuel filler lid / 4-21

Sunroof / 4-24

Features of your vehicle

4

Steering wheel / 4-28

Mirrors / 4-30

Instrument cluster / 4-34

Rear parking assist system / 4-48

Hazard warning flasher / 4-50

Lighting / 4-51

Wipers and washers / 4-56

Interior light / 4-60

Defroster / 4-62

Manual climate control system / 4-64

Automatic climate control system / 4-73

Windshield defrosting and defogging / 4-81

Storage compartment / 4-85

Interior features / 4-89

Exterior features / 4-99

Audio system / 4-101

Features of your vehicle

KEYS

D010200AFD

Key operations

Used to start the engine, lock and unlock

the doors.

WARNING - Ignition key

Leaving children unattended in a

vehicle with the ignition key is dan-

gerous even if the key is not in the

ignition. Children copy adults and

they could place the key in the igni-

tion. The ignition key would enable

children to operate power windows

or other controls, or even make the

vehicle move, which could result in

serious bodily injury or even death.

Never leave the keys in your vehicle

with unsupervised children.

OFD047001UK

OFD047001-B

D010100AFD-EA

D010300AFD-EA

Record your key number

Immobiliser system

The key code number is stamped on the

bar code tag attached to the key set.

Should you lose your keys, this number

will enable an authorised HYUNDAI deal-

er to duplicate the keys easily. Remove

the bar code tag and store it in a safe

place. Also, record the code number and

keep it in a safe and handy place, but not

in the vehicle.

Your vehicle is equipped with an elec-

tronic engine immobiliser system to

reduce the risk of unauthorised vehicle

use.

Your immobiliser system is comprised of

a small transponder in the ignition key,

and antenna coil in the key cylinder and

Immobiliser Control Unit (or Smartra

Unit).

With this system, whenever you insert

your ignition key into the ignition switch

and turn it to ON, the antenna coil in the

ignition switch receives a signal from the

transponder in the ignition key and then

sends the signal to the ECU (Engine

Control Unit).

WARNING

Use only HYUNDAI original parts

for the ignition key in your vehicle.

If an aftermarket key is used, the

ignition switch may not return to

ON after START. If this happens,

the starter will continue to operate

causing damage to the starter

motor and possible fire due to

excessive current in the wiring.

4 2

Features of your vehicle

The ECU checks the signal whether the

ignition key is valid. If the key is deter-

mined to be valid, the engine will start. If

the key is determined to be invalid, the

engine will not start.

✽

NOTICE

CAUTION

When starting the engine, do not use the

key with other immobiliser keys around.

Otherwise the engine may not start or

may stop soon after it starts. Keep each

key separately not to have any malfunc-

tion after you receive your new vehicle.

The transponder in your ignition

key is an important part of the

immobiliser system. It is designed

to give years of trouble-free service,

however you should avoid expo-

sure to moisture, static electricity

and rough handling. Immobiliser

system malfunction could occur.

To deactivate the immobiliser sys-

tem:

Insert the ignition key into the key cylin-

der and turn it to the ON position.

CAUTION

Do not put metal accessories near

the ignition switch.

The engine may not start as the

metal accessories may interrupt the

transponder signal from normally

transmitting.

To activate the immobiliser system:

Turn the ignition key to the OFF position.

The immobiliser system activates auto-

matically. Without a valid ignition key for

your vehicle, the engine will not start.

CAUTION

Do not change, alter or adjust the

immobiliser system because it

could cause the immobiliser sys-

tem to malfunction and should only

be serviced by an authorised

HYUNDAI dealer.

WARNING

In order to prevent theft of your

vehicle, do not leave spare keys

anywhere in your vehicle.

✽

NOTICE

If you need additional keys or lose your

keys, consult an authorised HYUNDAI

dealer.

Malfunctions caused by improper

alterations, adjustments or modifi-

cations to the immobiliser system

are not covered by your vehicle

manufacturer warranty.

4 3

Features of your vehicle

REMOTE KEYLESS ENTRY (IF EQUIPPED)

D020101AUN-EE

D020104AUN-EA

Lock (1)

Tailgate unlock (3)

All doors are locked if the lock button is

pressed.

The tailgate is unlocked if the button is

pressed (for more than 0.5 seconds).

If all doors are closed, the hazard warn-

ing lights blink once to indicate that all

doors are locked. However, if any door

remains open, the hazard warning lights

will not blink. If all doors are closed after

the lock button is pressed, the hazard

warning lights blink.

The hazard warning lights will blink twice

to indicate that the tailgate is unlocked.

After depressing this button, the tailgate

will relock automatically unless you open

the tailgate within 30 seconds.

Also, once the tailgate is opened and

then closed, the tailgate will lock auto-

matically.

OFD049305

D020102AUN-EA

Remote keyless entry system

Unlock (2)

All doors are unlocked if the unlock but-

ton is pressed.

The hazard warning lights will blink twice

to indicate that all doors are unlocked.

After depressing this button, the doors

will relock automatically unless you open

any door within 30 seconds.

operations

To unfold the key, press the release but-

ton then the key will unfold automatically.

To fold the key, fold the key manually

while pressing the release button.

CAUTION

Do not fold the key without press-

ing the release button. This may

damage the key.

4 4

Features of your vehicle

D020200AFD-EA

CAUTION

Transmitter precautions

• The keyless entry system trans-

mitter is designed to give you

years of trouble-free use, howev-

er it can malfunction if exposed to

moisture or static electricity. If

you are unsure how to use your

transmitter or replace the battery,

contact an authorised HYUNDAI

dealer.

• Using the wrong battery can

cause the transmitter to malfunc-

tion. Be sure to use the correct

battery.

✽

NOTICE

The transmitter will not work if any of

following occur:

• The ignition key is in ignition switch.

• You exceed the operating distance

limit (about 10 m [30 feet]).

• The battery in the transmitter is

weak.

• Other vehicles or objects may be

blocking the signal.

OFD047003

• The weather is extremely cold.

• The transmitter is close to a radio

transmitter such as a radio station or

an airport which can interfere with

normal operation of the transmitter.

When the transmitter does not work

correctly, open and close the door with

the ignition key. If you have a problem

with the transmitter, contact an autho-

rised HYUNDAI dealer.

D020300BFD-EA

Battery replacement

• To avoid damaging the transmit-

ter, don't drop it, get it wet, or

expose it to heat or sunlight.

The transmitter uses a 3 volt lithium bat-

tery which will normally last for several

years. When replacement is necessary,

use the following procedure.

1. Insert a slim tool into the slot and gen-

tly pry open the transmitter centre

cover (1).

2. Replace the battery with new one.

When replacing the battery, make sure

the battery positive “+” symbol faces

up as indicated in the illustration.

3. Install the battery in the reverse order

of removal.

CAUTION

An inappropriately disposed bat-

tery can be harmful to the environ-

ment and human health.

Dispose the battery according to

your local law(s) or regulation.

CAUTION

Keep the transmitter away from

water or any liquid. If the keyless

entry system is inoperative due to

exposure to water or liquids, it will

not be covered by your manufactur-

er vehicle warranty.

For replacement transmitters, see an

authorised HYUNDAI dealer for repro-

gramming.

4 5

Features of your vehicle

THEFT-ALARM SYSTEM (IF EQUIPPED)

D030100AUN-EA

• Do not arm the system until all pas-

sengers have left the vehicle. If the

system is armed while a passen-

ger(s) remains in the vehicle, the

alarm may be activated when the

remaining passenger(s) leave the

vehicle. If any door (or tailgate) or

engine bonnet is opened within 30

seconds after the system enters the

armed stage, the system is dis-

armed to prevent unnecessary

alarm.

Armed stage

Park the car and stop the engine. Arm

the system as described below.

1. Remove the ignition key from the igni-

tion switch and exit the vehicle.

2. Make sure that all doors (and tailgate)

and the engine bonnet are closed and

latched.

Armed

stage

Theft-alarm

stage

Disarmed

stage

3. Lock the doors using the transmitter of

the keyless entry system.

After completion of the steps above, the

hazard warning lights will blink once to

indicate that the system is armed.

D030000AUN-EA

This system is designed to provide pro-

tection from unauthorised entry into the

car. This system is operated in three

stages: the first is the "Armed" stage, the

second is the "Theft-alarm" stage, and

the third is the "Disarmed" stage. If trig-

gered, the system provides an audible

alarm with blinking of the hazard warning

lights.

If any door (or tailgate) or engine bonnet

remains open, the hazard warning lights

will not blink and the theft-alarm will not

arm. If all doors (and tailgate) and engine

bonnet are closed after the lock button is

pressed, the hazard warning lights blink

once.

4 6

Features of your vehicle

D030200AFD-EA

D030400AFD-EA

CAUTION

Theft-alarm stage

Disarmed stage

Do not change, alter or adjust the

theft-alarm system because it could

cause the theft-alarm system to

malfunction and should only be

serviced by an authorized HYUNDAI

dealer.

Malfunctions caused by improper

alterations, adjustments or modifi-

cations to the theft-alarm system

are not covered by your vehicle

manufacturer warranty.

The alarm will be activated if any of the

following occurs while the system is

armed.

• A front or rear door is opened without

using the transmitter.

• The tailgate is opened without using

the transmitter.

• The engine bonnet is opened.

The siren will sound and the hazard

warning lights will blink continuously for

27 seconds, unless the system is dis-

armed. To turn off the system, unlock the

doors with the ignition key (*) or transmit-

ter.

(*) : To enable the ignition key to function,

consult your authorised HYUNDAI

dealer.

The system will be disarmed when the

doors are unlocked by depressing the

unlock button on the transmitter.

After depressing unlock button, the haz-

ard warning lights will blink twice to indi-

cate that the system is disarmed.

After depressing unlock button, if any

door is not opened within 30 seconds,

the system will be rearmed.

✽

NOTICE

• If the system is not disarmed with the

transmitter, insert the key into the

ignition switch and start the engine.

Then the system will be disarmed.

• If you lose your keys, consult your

authorised HYUNDAI dealer.

4 7

Features of your vehicle

DOOR LOCKS

• Doors can also be locked and

unlocked with the transmitter key (if

equipped).

• Once the doors are unlocked, they may

be opened by pulling the door handle.

• When closing the door, push the door

by hand. Make sure that doors are

closed securely.

Unlock

Lock

❈ If your vehicle is equipped with the

remote keyless entry system, there is

no key lock on the front passenger's

door.

OHD046001R

OFD047010R

D050100AUN-EA

• To lock a door without the key, push the

inside door lock button (1) or central

door lock switch (2 to the “Lock” posi-

)

Operating door locks from out-

side the vehicle

• Turn the key towards the rear of vehicle

to unlock and towards the front of vehi-

cle to lock.

• If you lock/unlock the door with a key,

all vehicle doors will lock/unlock auto-

matically.

✽

NOTICE

• In cold and wet climates, door lock

and door mechanisms may not work

properly due to freezing conditions.

• If the door is locked/unlocked multi-

ple times in rapid succession with

either the vehicle key or door lock

switch, the system may stop operating

temporarily in order to protect the

circuit and prevent damage to system

components.

tion and close the door (3).

• If you lock the door with the central

door lock switch, all vehicle doors will

lock automatically.

✽

NOTICE

Always remove the ignition key, engage

the hand brake, close all windows and

lock all doors when leaving your vehicle

unattended.

4 8

Features of your vehicle

Driver’s door

• Front doors cannot be locked if the

ignition key is in the ignition switch and

any front door is open.

WARNING - Door lock mal-

function

Lock

Unlock

If a power door lock ever fails to

function while you are in the vehi-

cle, try one or more of the following

techniques to exit:

• Operate the door unlock feature

repeatedly (both electronic and

manual) while simultaneously

pulling on the door handle.

• Operate the other door locks and

handles, front and rear.

• Lower a front window and use the

key to unlock the door from out-

side.

• Move to the cargo area and open

the tailgate.

OFD047011R

OFD047012R

D050202AUN-EA

Operating door locks from inside

the vehicle

With central door lock switch

Operate by depressing the central door

lock switch.

D050201AFD

With the door lock button

• To unlock a door, push the door lock

button (1) to the “Unlock” position. The

red mark (2) on the button will be visi-

ble.

• To lock a door, push the door lock but-

ton (1) to the “Lock” position. If the door

is locked properly, the red mark (2) on

the door lock button will not be visible.

• To open a door, pull the door handle

(3) outward.

• If the inner door handle of the front

door is pulled when the door lock but-

ton is in lock position, the button is

unlocked and door opens. (if equipped)

4 9

Features of your vehicle

D050600ANF

• When pushing down on the front por-

tion (1) of the switch, all vehicle doors

will lock.

• When pushing down on the rear por-

tion (2) of the switch, all vehicle doors

will unlock.

• However, if the key is in the ignition

switch and any front door is open, the

doors will not lock when the front por-

tion of central door lock switch is

pressed.

Deadlocks (if equipped)

WARNING - Unlocked

vehicles

Some vehicles are equipped with a

deadlocking system. Deadlocks prevent

opening of a door from either inside or

outside the vehicle once the deadlocks

have been activated providing an addi-

tional measure of vehicle security.

To lock the vehicle using the deadlock

function, the doors must be locked using

the key or the Remote Keyless Entry

transmitter. To unlock the vehicle, the key

or the transmitter must again be used.

Leaving your vehicle unlocked can

invite theft or possible harm to you

or others from someone hiding in

your vehicle while you are gone.

Always remove the ignition key,

engage the hand brake, close all

windows and lock all doors when

leaving your vehicle unattended.

WARNING - Doors

To lock a vehicle without using the dead-

lock function, the doors should be locked

by depressing the central door lock

switch and closing the doors.

WARNING - Unattended

children

• The doors should always be fully

closed and locked while the vehi-

cle is in motion to prevent acci-

dental opening of the door.

Locked doors will also discour-

age potential intruders when the

vehicle stops or slows.

An enclosed vehicle can become

extremely hot, causing death or

severe injury to unattended chil-

dren or animals who cannot escape

the vehicle. Furthermore, children

might operate features of the vehi-

cle that could injure them, or they

could encounter other harm, possi-

bly from someone gaining entry to

the vehicle. Never leave children or

animals unattended in your vehicle.

WARNING

Occupants must not be allowed to

remain in the vehicle when the

deadlocking system is activated

since it will not be possible for

them, or persons outside the vehi-

cle, to open the doors and leave the

vehicle in case of an emergency.

• Be careful when opening doors

and watch for vehicles, motorcy-

cles, bicycles or pedestrians

approaching the vehicle in the

path of the door. Opening a door

when something is approaching

can cause damage or injury.

4 10

Features of your vehicle

D050300AUN-EA

D050400AFD-EA

Impact sensing door unlock sys-

tem (if equipped)

Speed sensing door lock system

(if equipped)

All doors will automatically unlock when

an impact is acknowledged by the impact

sensors while the ignition is switch ON.

However, the doors may not be unlocked

if mechanical problems occur with the

door lock system or battery.

Type A

When the speed of the vehicle reaches

above 40 km/h for 1 second, it will auto-

matically lock all doors. For activation of

this feature, contact an authorised

HYUNDAI dealer.

Type B

When the speed of the vehicle reaches

above 15 km/h for 1 second, it will auto-

matically lock all doors. For activation of

this feature, contact an authorised

HYUNDAI dealer.

OFD047013

D050500AUN

Child-protector rear door lock

The child safety lock is provided to help

prevent children from accidentally open-

ing the rear doors from inside the vehicle.

The rear door safety locks should be

used whenever children are in the vehi-

cle.

✽

NOTICE

An authorised HYUNDAI dealer can

select some auto door lock/unlock fea-

tures as follows;

1. Open the rear door.

• Speed sensing auto door locking

• Auto door unlock when the ignition

key is removed from the ignition

switch

2. Push the child safety lock located on

the rear edge of the door to the “Lock”

position. When the child safety lock is

)” position, rear door

will not open even when the inner door

handle is pulled inside the vehicle.

in the “Lock (

If you want to select a door lock/unlock

feature,

consult

an

authorised

HYUNDAI dealer.

3. Close the rear door.

4 11

Features of your vehicle

TAILGATE

To open the rear door, pull the outside

door handle (1).

Even though the doors may be unlocked,

the rear door will not open by pulling the

inner door handle (2) until rear door child

✽

NOTICE

In cold and wet climates, door lock and

door mechanisms may not work proper-

ly due to freezing conditions.

safety lock is unlocked (

).

WARNING

WARNING - Rear door

locks

The tailgate swings upward. Make

sure no objects or people are near

the rear of the vehicle when open-

ing the tailgate.

If children accidentally open the

rear doors while the vehicle is in

motion, they could fall out of the

vehicle, resulting in severe injury or

death. To prevent children from

opening the rear doors from the

inside, the rear door safety locks

should be used whenever children

are in the vehicle.

OFD047014

D070100AFD

CAUTION

Opening the tailgate

Make certain that you close the tail-

gate before driving your vehicle.

Possible damage may occur to the

tailgate lift cylinders and attaching

hardware if the tailgate is not

closed prior to driving.

• The tailgate is locked or unlocked

together if all doors are locked or

unlocked with the key, transmitter or

central door lock switch.

• The tailgate is unlocked alone for 30

seconds if the tailgate unlock button on

the transmitter is pressed. Once the

tailgate is opened and then closed, the

tailgate is locked automatically.

• If unlocked, the tailgate can be opened

by pressing the handle and pulling it

up.

4 12

Features of your vehicle

D070200AUN

Closing the tailgate

WARNING

• For emergency, be fully aware of

the location of the emergency

tailgate safety release lever in

their vehicle and how to open the

tailgate if you are accidentally

locked in the luggage compart-

ment.

To close the tailgate, lower and push

down the tailgate firmly. Make sure that

the tailgate is securely latched.

WARNING - Exhaust

fumes

• No one should be allowed to

occupy the luggage compartment

of the vehicle at any time. The

luggage compartment is a highly

dangerous location in the event

of a crash.

• Use the release lever for emer-

gency only. Use extreme caution

while the vehicle is in motion.

If you drive with the tailgate open,

you will draw dangerous exhaust

fumes into your vehicle which can

cause serious injury or death to

vehicle occupants.

If you must drive with the tailgate

open, keep the air vents and all win-

dows open so that additional out-

side air comes into the vehicle.

OFD047015

D070300AUN

Emergency tailgate safety release

Your vehicle is equipped with emergency

tailgate safety release lever located on

the bottom of the tailgate. When some-

one is inadvertently locked in the lug-

gage compartment, if the lever is

pushed, the tailgate latch mechanism is

released and the tailgate is opened by

pushing backward.

WARNING - Rear cargo

area

Occupants should never ride in the

rear cargo area where no restraints

are available. To avoid injury in the

event of an accident or sudden

stops, occupants should always be

properly restrained.

4 13

Features of your vehicle

WINDOWS

D080000AFD

(1) Driver’s door power window switch

(2) Front passenger’s door power win-

dow switch

Type A

(3) Rear door (left) power window switch

(4) Rear door (right) power window

switch

(5) Window opening and closing

(6) Automatic power window up*/down*

(7) Power window lock switch

Type B

*: if equipped

✽

NOTICE

In cold and wet climates, power win-

dows may not work properly due to

freezing conditions.

Type C

OFD037029R

4 14

Features of your vehicle

D080100BFD

Power windows

The ignition switch must be in the ON

position for power windows to operate.

Each door has a power window switch

that controls the door’s window. The driv-

er has a power window lock switch which

can block the operation of rear passen-

ger windows.

The power windows can be operated for

approximately 30 seconds after the igni-

tion key is removed or turned to the ACC

or LOCK position. However, if the front

doors are opened, the power windows

cannot be operated even within the 30

seconds period after the ignition key

removal.

OFD037030R

OFD037031R

D080101AUN

D080102AUN

Window opening and closing

(if equipped)

The driver’s door has a master power

window switch that controls all the win-

dows in the vehicle.

To open or close a window, press down

or pull up the front portion of the corre-

sponding switch to the first detent posi-

tion (5).

Auto down window (if equipped)

Depressing the power window switch

momentarily to the second detent posi-

tion (6) completely lowers the driver’s

window even when the switch is

released. To stop the window at the

desired position while the window is in

operation, momentarily pull the switch in

the direction opposite of the window’s

movement.

✽

NOTICE

While driving with the rear windows

down or with the sunroof (if equipped)

in an open (or partially open) position,

your vehicle may demonstrate a wind

buffeting or pulsation noise. This

noise is a normal occurrence and can be

reduced or eliminated by taking the fol-

lowing actions. If the noise occurs with

one or both of the rear windows down,

partially lower both front windows

approximately one inch. If you experi-

ence the noise with the sunroof open,

slightly reduce the size of the sunroof

opening.

4 15

Features of your vehicle

If the power window is not operated cor-

rectly, the automatic power window sys-

tem must be reset as follows:

1. Turn the ignition switch to the ON posi-

tion.

2. Close driver’s window and continue

pulling up on driver’s power window

switch for at least 1 second after the

window is completely closed.

✽

NOTICE

The automatic reverse feature for the

driver’s window is only active when the

“auto up” feature is used by fully

pulling up the switch. The automatic

reverse feature will not operate if the

window is raised using the halfway posi-

tion on the power window switch.

WARNING

Automatic reversal

Always check for obstructions

before raising any window to avoid

injuries or vehicle damage. If an

object less than 4 mm (0.16 in.) in

diameter is caught between the

window glass and the upper win-

dow channel, the automatic reverse

window may not detect the resist-

ance and will not stop and reverse

direction.

If the upward movement of the window is

blocked by an object or part of the body,

the window will detect the resistance and

will stop upward movement. The window

will then lower approximately 30 cm (11.8

in.) to allow the object to be cleared.

If the window detects the resistance

while the power window switch is pulled

up continuously, the window will stop

upward movement then lower approxi-

mately 2.5 cm (1 in.). And if the power

window switch is pulled up continuously

again within 5 seconds after the window

is lowered by the automatic window

reversal feature, the automatic window

reversal will not operate.

OFD037032R

D080103AUN

Auto up/down window (if equipped)

Depressing or pulling up the power win-

dow switch momentarily to the second

detent position (6) completely lowers or

lifts the window even when the switch is

released. To stop the window at the

desired position while the window is in

operation, pull up or depress and release

the switch to the opposite direction of the

movement.

4 16

Features of your vehicle

CAUTION

WARNING - Windows

• To prevent possible damage to

the power window system, do not

open or close two windows or

more at the same time. This will

also ensure the longevity of the

fuse.

• Never try to operate the main

switch on the driver's door and

the individual door window

switch in opposing directions at

the same time. If this is done, the

window will stop and cannot be

opened or closed.

• NEVER leave the ignition key in

the vehicle.

• NEVER leave any child unattend-

ed in the vehicle. Even very

young children may inadvertently

cause the vehicle to move, entan-

gle themselves in the windows,

or otherwise injure themselves or

others.

• Always double check to make

sure all arms, hands, head and

other obstructions are safely out

of the way before closing a win-

dow.

OFD047020R

D080104AUN

Power window lock button

• The driver can disable the power win-

dow switches on a rear passenger

door by depressing the power window

lock switch located on the driver’s door

to LOCK (pressed).

• When the power window lock switch

is ON, the driver’s master control

cannot operate the rear passenger

door power windows.

• Do not allow children to play with

the power windows. Keep the dri-

ver’s door power window lock

switch in the LOCK position

(depressed). Serious injury can

result from unintentional window

operation by the child.

• Do not extend any head or arms

outside through the window

opening while driving.

4 17

Features of your vehicle

B050A01E-R

D080200AFD

Manual windows (if equipped)

To raise or lower the window, turn the

window regulator handle clockwise or

counterclockwise.

WARNING

When opening or closing the win-

dows, make sure your passenger's

arms, hands and body are safely

out of the way.

4 18

Features of your vehicle

BONNET

OFD047021R

OFD047022

OFD047016

D090100AUN-EA

2. Go to the front of the vehicle, raise the

bonnet slightly, pull the secondary

latch (1) inside of the bonnet centre

and lift the bonnet (2).

3.Pull the support rod from the bonnet.

4.Hold the bonnet open with the support

rod.

Opening the bonnet

1. Pull the release lever to unlatch the

bonnet. The bonnet should pop open

slightly.

WARNING - Hot parts

Grasp the support rod in the area

wrapped in rubber. The rubber will

help prevent you from being burned

by hot metal when the engine is

hot.

4 19

Features of your vehicle

D090200AUN-EA

Closing the bonnet

WARNING - Bonnet

WARNING

• Before closing the bonnet,

ensure that all obstructions are

removed from the bonnet open-

ing. Closing the bonnet with an

obstruction present in the bonnet

opening may result in property

damage or severe personal

injury.

• Do not leave gloves, rags or any

other combustible material in the

engine compartment. Doing so

may cause a heat-induced fire.

• Always double check to be sure

that the bonnet is firmly latched

before driving away. If it is not

latched, the bonnet could fly

open while the vehicle is being

driven, causing a total loss of vis-

ibility, which might result in an

accident.

• The support rod must be inserted

completely into the hole provided

in the bonnet whenever you

inspect the engine compartment.

This will prevent the bonnet from

falling and possibly injuring you.

1. Before closing the bonnet, check the

following:

• All filler caps in engine compartment

must be correctly installed.

• Gloves, rags or any other com-

bustible material must be removed

from the engine compartment.

2. Return the support rod to its clip to

prevent it from rattling.

3. Lower the bonnet until it is about 30

cm (1 ft.) above the closed position

and let it drop. Make sure that it locks

into place.

• Do not move the vehicle with the

bonnet in the raised position, as

vision is obstructed and the bon-

net could fall or be damaged.

4 20

Features of your vehicle

FUEL FILLER LID

D100200AUN

Closing the fuel filer lid

1. To install the cap, turn it clockwise until

it “clicks”. This indicates that the cap is

securely tightened.

2. Close the fuel filler lid and push it in

lightly making sure that it is securely

closed.

OHD046014R

OUN026020

D100100AFD

1. Stop the engine.

Opening the fuel filer lid

2. To open the fuel filler lid, pull the fuel

filler lid opener up.

3. Pull the fuel filler lid (1) out to fully

open.

4. To remove the cap (2), turn the fuel

tank cap counterclockwise.

The fuel-filler lid must be opened from

inside the vehicle by pulling up on the

fuel-filler lid opener located on the front

floor area on the driver’s seat.

5. Refuel as needed.

✽

NOTICE

If the fuel-filler lid will not open because

ice has formed around it, tap lightly or

push on the lid to break the ice and

release the lid. Do not pry on the lid. If

necessary, spray around the lid with an

approved de-icer fluid (do not use radi-

ator anti-freeze) or move the vehicle to a

warm place and allow the ice to melt.

4 21

Features of your vehicle

D100300AFD-EA

(Continued)

WARNING - Refuelling

dangers

• Do not get back into a vehicle

once you have begun refuelling

since you can generate static

electricity by touching, rubbing

or sliding against any item or fab-

ric (polyester, satin, nylon, etc.)

capable of producing static elec-

tricity. Static electricity discharge

can ignite fuel vapours resulting

in rapid burning. If you must re-

enter the vehicle, you should

once again eliminate potentially

dangerous static electricity dis-

charge by touching a metal part

of the vehicle, away from the fuel

filler neck, nozzle or other petrol

source.

• When using a portable fuel con-

tainer be sure to place the con-

tainer on the ground prior to refu-

elling. Static electricity discharge

from the container can ignite fuel

vapours causing a fire. Once

refuelling has begun, contact

with the vehicle should be main-

tained until the filling is com-

plete.

WARNING - Refuelling

Automotive fuels are flammable

materials. When refuelling, please

note the following guidelines care-

fully. Failure to follow these guide-

lines may result in severe personal

injury, severe burns or death by fire

or explosion.

• Read and follow all warnings

posted at the petrol station facili-

ty.

• Before refuelling, note the loca-

tion of the Emergency Fuel Shut-

Off, if available, at the petrol sta-

tion facility.

• Before touching the fuel nozzle,

you should eliminate potentially

dangerous static electricity dis-

charge by touching another metal

part of the vehicle, a safe dis-

tance away from the fuel filler

neck, nozzle, or other petrol

source.

• If pressurized fuel sprays out, it

can cover your clothes or skin

and thus subject you to the risk

of fire and burns. Always remove

the fuel cap carefully and slowly.

If the cap is venting fuel or if you

hear a hissing sound, wait until

the condition stops before com-

pletely removing the cap.

• Do not "top off" after the nozzle

automatically shuts off when

refuelling.

• Always check that the fuel cap is

installed securely to prevent fuel

spillage in the event of an acci-

dent.

(Continued)

4 22

Features of your vehicle

(Continued)

• Do not spill fuel on the exterior

surfaces of the vehicle. Any type

of fuel spilled on painted surfaces

may damage the paint.

• After refuelling, make sure the

fuel cap is installed securely to

prevent fuel spillage in the event

of an accident.

Use only portable plastic fuel

containers designed to carry and

store petrol.

• Do not use mobile phones while

refuelling. Electric current and/or

electronic interference from

mobile phones can potentially

ignite fuel vapours causing a fire.

• If a fire breaks out during refu-

elling, leave the vicinity of the

vehicle, and immediately contact

the manager of the petrol station

and then contact the local fire

department. Follow any safety

instructions they provide.

• When refuelling, always shut the

engine off. Sparks produced by

electrical components related to

the engine can ignite fuel

vapours causing a fire. Once

refuelling is complete, check to

make sure the filler cap and filler

door are securely closed, before

starting the engine.

• DO NOT use matches or a lighter

and DO NOT SMOKE or leave a lit

cigarette in your vehicle while at

a petrol station especially during

refuelling. Automotive fuel is

highly flammable and can, when

ignited, result in fire.

CAUTION

• Make sure to refuel your vehicle

according to the "Fuel require-

ments" suggested in section 1.

• If the fuel filler cap requires

replacement, use only a genuine

HYUNDAI cap or the equivalent

specified for your vehicle. An

incorrect fuel filler cap can result

in a serious malfunction of the

fuel system or emission control

system.

(Continued)

4 23

Features of your vehicle

SUNROOF (IF EQUIPPED)

✽

NOTICE

• In cold and wet climates, sunroof may

not work properly due to freezing

conditions.

• After washing the car or after there is

rain, be sure to wipe off any water

that is on the sunroof before operating

it.

1

3

CAUTION

Do not continue to press the sun-

roof control button(s) after the sun-

roof is in the fully open, closed, or

tilt position(s). Damage to the motor

or system components could occur.

OFD047023

OFD047024

D110000AUN

D110100AFD

If your vehicle is equipped with this fea-

ture, you can slide or tilt your sunroof

with the sunroof control buttons located

on the overhead console.

1. Slide button

Sliding the sunroof

To open the sunroof (autoslide feature),

press the slide button (1) on the over-

head console for more than 0.5 second.

The sunroof will slide to the recommend-

ed open position (about 50mm before the

maximum slide open position).

✽

NOTICE

2. Tilt button

3. Close button

The sunroof cannot slide when it is in

the tilt position nor can it be tilted while

in an open or slide position.

To stop the sunroof sliding at any point,

press any sunroof control button.

The sunroof can only be opened, closed,

or tilted when the ignition switch is in the

ON position.

WARNING

Never adjust the sunshade while

driving. This could result in loss of

control and an accident that may

cause death, serious injury, or

property damage.

4 24

Features of your vehicle

To open the sunroof to the maximum

slide open position, press the slide but-

ton (1) once again and hold it until the

sunroof slide all the way open.

✽

NOTICE

To reduce wind noise while driving, we

recommend you to drive at the recom-

mended postion (about 50mm before the

maximum slide open positon).

2

3

To close the sunroof (autoslide feature),

press the close button (3) on the over-

head console for more than 0.5 second.

The sunroof will slide all the way close.To

stop the sunroof sliding at any point,

press any sunroof control button.

OUN026027

OFD047025

D110101AUN

D110200AUN

Automatic reversal

Tilting the sunroof

If an object or part of the body is detect-

ed while the sunroof is closing automati-

cally, it will reverse direction, and then

stop.

Auto reverse function does not work if a

tiny obstacle is between the sliding glass

and the sunroof sash. You should always

check that all passengers and objects

are away from the sunroof before closing

it.

To open the sunroof (autotilt feature),

press the tilt button (2) on the overhead

console for more than 0.5 second.

The sunroof will tilt all the way open. To

stop the sunroof tilting at any point, press

any sunroof control button.

To close the sunroof, press the close but-

ton (3) on the overhead console and hold

it until the sunroof is closed.

4 25

Features of your vehicle

CAUTION

WARNING - Sunroof

• Be careful that no heads, hands

and body parts are obstructing a

closing sunroof.

• Do not extend the face, neck,

arms or body outside the sunroof

while driving.

• Make sure your hands and head

are safely out of the way before

closing a sunroof.

• Periodically remove any dirt that

may accumulate on the guide rail.

• If you try to open the sunroof

when the temperature is below

freezing or when the sunroof is

covered with snow or ice, the

glass or the motor could be dam-

aged.

• While using sunroof for a long

time, a dust between sunroof and

roof panel can make a noise.

OUN026031

D110300AUN

Open the sunroof and remove

regularly the dust using clean

cloth.

• The sunroof is made to slide

together with sunshade. Do not

leave the sunshade closed while

the sunroof is open.

Sunshade

The sunshade will be opened with the

glass panel automatically when the glass

panel is slid.You will have to close it man-

ually if you want it closed.

4 26

Features of your vehicle

❈ For more detailed information, contact

an authorized HYUNDAI dealer.

Resetting the sunroof

Whenever the vehicle battery is discon-

nected or discharged, or related fuse is

blown, you must reset your sunroof sys-

tem as follows:

CAUTION

If the sunroof is not reset when the

vehicle battery is disconnected or

discharged, or related fuse is

blown, the sunroof may operate

improperly.

1. Turn the ignition switch to the ON

position and close the sunroof com-

pletely.

2. Release the control button.

3. Press and hold the close button until

the sunroof tilts and slightly moves up

and down. Then, release the button.

4. Press and hold the close button until

the sunroof is operated as follows;

TILT DOWN → SLIDE OPEN →

SLIDE CLOSE

Then, release the control button.

When this is complete, the sunroof sys-

tem is reset.

4 27

Features of your vehicle

STEERING WHEEL

D130200BFD-EA

D130300AFD

✽

NOTICE

Tilt steering

Electric power steering

The following symptoms may occur dur-

A tilt steering wheel allows you to adjust

the steering wheel before you drive. You

can also raise it to give your legs more

room when you exit and enter the vehicle

(if equipped).

Power steering uses a motor to assist

you in steering the vehicle. If the engine

is off or if the power steering system

becomes inoperative, the vehicle may

still be steered, but it will require

increased steering effort.

The motor driven power steering is con-

trolled by power steering control unit

which sense the steering wheel torque,

steering wheel position and vehicle

speed to command the motor.

The steering wheel becomes heavier as

the vehicle’s speed increases and

becomes lighter as the vehicle’s speed

decreases for the better control of the

steering wheel.

ing normal vehicle operation:

• The EPS warning light does not illu-

minate.

• The steering wheel becomes heavier

after turning the ignition switch on.

This happens as the system performs

the EPS system diagnostics. When the

diagnostics is completed, the steering

wheel will return to its normal condi-

tion.

The steering wheel should be positioned

so that it is comfortable for you to drive,

while permitting you to see the instru-

ment panel warning lights and gauges.

• A click noise may be heard from the

EPS relay after the ignition switch is

turned to the ON or LOCK position.

• Motor noise may be heard when the

vehicle is at a stop or at a low driving

speed.

• If the Electric Power Steering System

does not operate normally, the warn-

ing light will illuminate on the instru-

ment cluster. The steering wheel may

become difficult to control or operate

abnormally. Take your vehicle to an

authorised HYUNDAI dealer and

have the vehicle checked as soon as

possible.

Should you notice any change in the

effort required to steer during normal

vehicle operation, have the power steer-

ing checked by an authorised HYUNDAI

dealer.

• When you operate the steering wheel

in low temperature, abnormal noise

could occur. If temperature rises, the

noise will disappear. This is a normal

condition.

4 28

Features of your vehicle

WARNING

• Never adjust the angle and height

of steering wheel while driving.

You may lose your steering con-

trol and cause severe personal

injury or accidents.

• After adjusting, push the steering

wheel both up and down to be

certain it is locked in position.

3

OFD047028R

OFD047029

D130500AUN

To change the steering wheel angle, pull

down the lock release lever (1), adjust Horn

the steering wheel to the desired angle

(2) and height (if equipped) (3), then pull

up the lock-release lever to lock the

steering wheel in place. Be sure to adjust

the steering wheel to the desired position

before driving.

To sound the horn, press the horn sym-

bol on your steering wheel.

Check the horn regularly to be sure it

operates properly.

✽

NOTICE

To sound the horn, press the area indi-

cated by the horn symbol on your steer-

ing wheel (see illustration). The horn

will operate only when this area is

pressed.

CAUTION

Do not strike the horn severely to

operate it, or hit it with your fist. Do

not press on the horn with a sharp-

pointed object.

4 29

Features of your vehicle

MIRRORS

D140100AUN-EA

D140102AUN

Electric chromic mirror (ECM)

(if equipped)

Inside rearview mirror

Adjust the rearview mirror to centre on

the view through the rear window. Make

this adjustment before you start driving.

The electric rearview mirror automatical-

ly controls the glare from the headlights

of the car behind you in nighttime or low

light driving conditions. The sensor

mounted in the mirror senses the light

level around the vehicle, and automati-

cally controls the headlight glare from

vehicles behind you.

WARNING - Rear visibility

Do not place objects in the rear

seat or cargo area which would

interfere with your vision out the

rear window.

When the engine is running, the glare is

automatically controlled by the sensor

mounted in the rearview mirror.

OFD047030

D140101AUN

Whenever the shift lever is shifted into

reverse (R), the mirror will automatically

go to the brightest setting in order to

improve the drivers view behind the vehi-

cle.

Day/night rearview mirror

Make this adjustment before you start

driving and while the day/night lever is in

the day position.

Pull the day/night lever toward you to

reduce glare from the headlights of vehi-

cles behind you during night driving.

CAUTION

Remember that you lose some rearview

clarity in the night position.

When cleaning the mirror, use a

paper towel or similar material

dampened with glass cleaner. Do

not spray glass cleaner directly on

the mirror as that may cause the liq-

uid cleaner to enter the mirror hous-

ing.

4 30

Features of your vehicle

D140200AUN

Outside rearview mirror

Be sure to adjust mirror angles before

driving.

Your vehicle is equipped with both left-

hand and right-hand outside rearview

mirrors. The mirrors can be adjusted

remotely with the remote switch. The mir-

ror heads can be folded back to prevent

damage during an automatic car wash or

when passing in a narrow street.

WARNING - Rearview mir-

rors

• The right outside rearview mirror

is convex. In some countries, the

left outside rearview mirror is

also convex. Objects seen in the

mirror are closer than they

appear.

• Use your interior rearview mirror

or direct observation to deter-

mine the actual distance of fol-

lowing vehicles when changing

lanes.

OFD047031

To operate the electric rearview mirror

• Press the ON/OFF button (1) to turn

the automatic dimming function on.

The mirror indicator light will illuminate.

CAUTION

Press the ON/OFF button to turn the

automatic dimming function off. The

mirror indicator light will turn off.

• The mirror defaults to the ON position

whenever the ignition switch is turned

on.

Do not scrape ice off the mirror

face; this may damage the surface

of the glass. If ice should restrict

movement of the mirror, do not

force the mirror for adjustment. To

remove ice, use a deicer spray, or a

sponge or soft cloth with very warm

water.

4 31

Features of your vehicle

CAUTION

If the mirror is jammed with ice, do

not adjust the mirror by force. Use

an approved spray de-icer (not radi-

ator antifreeze) to release the

frozen mechanism or move the

vehicle to a warm place and allow

the ice to melt.

WARNING

B510A01ER

OFD047032R

Do not adjust or fold the outside

rearview mirrors while the vehicle

is moving. This could result in loss

of control, and an accident which

could cause death, serious injury

or property damage.

D140201AFD-EA

Remote control

Manual type

The outside rearview mirrors are

equipped with a remote control for your

convenience. It is operated by the control

lever in the bottom front corner of the

window.

Before driving away, always check that

your mirrors are positioned so you can

see behind you, both to the left and right

sides, as well as directly behind your

vehicle. When using the mirror, always

exercise caution when attempting to

judge the distance of vehicles behind or

along side of you.

Electric type (if equipped)

The electric remote control mirror switch

allows you to adjust the position of the

left and right outside rearview mirrors. To

adjust the position of either mirror, move

the lever (1) to R or L to select the right

side mirror or the left side mirror, then

press a corresponding point on the mirror

adjustment control to position the select-

ed mirror up, down, left or right.

After adjustment, put the lever into neu-

tral position to prevent the inadvertent

adjustment.

4 32

Features of your vehicle

CAUTION

• The mirrors stop moving when

they reach the maximum adjust-

ing angles, but the motor contin-

ues to operate while the switch is

depressed. Do not depress the

switch longer than necessary, the

motor may be damaged.

• Do not attempt to adjust the out-

side rearview mirror by hand.

Doing so may damage the inter-

nal mirror mechanism.

B510E01ER

OFD047033R

D140202AFD

Electric type (if equipped)

To fold the outside rearview mirror,

depress the button.

Folding the outside rearview mirror

Manual type

To fold outside rearview mirror, grasp the

housing of mirror and then fold it toward

the rear of the vehicle.

To unfold it, depress the button again.

CAUTION

In case of the electric type of out-

side rearview mirror, don’t fold it by

hand. It could cause the failure of

the motor.

4 33

Features of your vehicle

INSTRUMENT CLUSTER

1. Tachometer

2. Engine temperature gauge

3. Fuel gauge

4. Speedometer

5. Turn signal indicators

6. Warning and indicator lights (if equipped)

7. Odometer/Trip computer (if equipped)

* The actual cluster in the vehicle may differ from the illustration.

For more details refer to the "Gauges" in the next pages.

OFD049034EA

D150000AFD

4 34

Features of your vehicle

Petrol

Diesel

OFD047035R

OFD047036

OFD047039/OFD047040

D150100AFD

D150202AFD

Gauges

D150201AUN-EA

Tachometer

Instrument panel illumination

(if equipped)

When the vehicle’s parking lights or

headlights are on, rotate the illumination

control knob to adjust the brightness of

the instrument panel illumination.

The instrument cluster illumination intensity

can be adjusted by rotating the control knob

with the headlight switch in any position

when the ignition switch is in ON position.

The tachometer indicates the approxi-

mate number of engine revolutions per

minute (rpm).

Use the tachometer to select the correct

shift points and to prevent lugging and/or

over-revving the engine.

The tachometer pointer may move slight-

ly when the ignition switch is in ACC or

ON position with the engine OFF. This

movement is normal and will not affect

the accuracy of the tachometer once the

engine is running.

Speedometer

The speedometer indicates the forward

speed of the vehicle.

The speedometer is calibrated in kilome-

ters per hour.

CAUTION

Do not operate the engine within

the tachometer's RED ZONE. This

may cause severe engine damage.

4 35

Features of your vehicle

Type A

Type B

Type A

Type B

WARNING

Never remove the radiator cap

when the engine is hot. The engine

coolant is under pressure and

could cause severe burns. Wait

until the engine is cool before

adding coolant to the reservoir.

OFD047041R

OFD047042

D150203AFD

D150204AFD

Engine temperature gauge

Fuel gauge

This gauge shows the temperature of the

engine coolant when the ignition switch

is ON.

Do not continue driving with an overheat-

ed engine. If your vehicle overheats, refer

to “If the engine overheats” in section 6.

The fuel gauge indicates the approxi-

mate amount of fuel remaining in the fuel

tank. The fuel tank capacity is given in

section 9. The fuel gauge is supplement-

ed by a low fuel warning light, which will

illuminate when the fuel tank is nearly

empty.

On inclines or curves, the fuel gauge

pointer may fluctuate or the low fuel

warning light may come on earlier than

usual due to the movement of fuel in the

tank.

CAUTION

If the gauge pointer moves beyond

the normal range area toward the

“H” or “130°C” position, it indicates

overheating that may damage the

engine.

4 36

Features of your vehicle

WARNING - Fuel gauge

Running out of fuel can expose

vehicle occupants to danger.

You must stop and obtain addition-

al fuel as soon as possible after the

warning light comes on or when the

gauge indicator comes close to the

E or “0” level.

CAUTION

OFD047043

OFD047049

Avoid driving with a very low fuel

level. If you run out of fuel, it could

cause the engine to misfire and

result in excessive loading of the

catalytic converter.

D150205AFD

Tripmeter (km or MI)

Odometer/Tripmeter (if equipped)

Odometer (km or MI)

The odometer indicates the total dis-

tance the vehicle has been driven.

You will also find the odometer useful to

determine when periodic maintenance

should be performed.

The tripmeter indicates the distance of

individual trip selected by the driver.

Tripmeter can be reset to 0 by pressing

the TRIP button for 1 second or more,

and then releasing.

✽

NOTICE

It is forbidden that alteration of the

odometer of any vehicle with the intent

to change the mileage registered on the

odometer. The alteration may void your

warranty coverage.

4 37

Features of your vehicle

Push the TRIP button for less than 1 sec-

ond to select distance to empty, average

fuel consumption, average speed or trip-

meter function as follows :

Distance to empty

Average fuel consumption

OFD047045

OFD047046

D150206AFD-EA

Distance to empty (km or MI)

Trip computer (if equipped)

This mode indicates the estimated dis-

tance to empty based on the current fuel

in the fuel tank and the amount of fuel

delivered to the engine. When the

remaining distance is below 50 km (30

miles), “---” will be displayed and the dis-

tance to empty indicator will blink.

Average speed

Tripmeter

The trip computer is a microcomputer-

controlled driver information system that

displays information related to driving,

including distance to empty, tripmeter,

average fuel consumption and average

speed on the display when the ignition

switch is in the ON position. All stored

driving information (except odometer) is

reset if the battery is disconnected. The

odometer is always displayed until the

display is turned off.

The meter’s working range is from 50 to

999 km (30 to 999 miles).

4 38

Features of your vehicle

✽

NOTICE

• If the vehicle is not on level ground or

the battery power has been interrupt-

ed, the “Distance to empty” function

may not operate correctly.

The trip computer may not register

additional fuel if less than 6 litres (1.6

gallons) of fuel are added to the vehi-

cle.

Average

speed

• The fuel consumption and distance to

empty values may vary significantly

based on driving conditions, driving

habits, and condition of the vehicle.

• The distance to empty value is an esti-

mate of the available driving distance.

This value may differ from the actual

driving distance available.

Odometer

OFD047047

OFD047048

Average fuel consumption

Average speed (km/h or MPH)

This mode calculates the average speed

of the vehicle since the last average

speed reset.

Even if the vehicle is not in motion, the

average speed keeps going while the

engine is running.

The meter's working range is from 0 to

240 km/h (0 to 150 mph).

Pressing the TRIP button for more than 1

second, when the average speed is

being displayed, clears the average

speed to zero (---).

(l/100 km or MPG)

This mode calculates the average fuel

consumption from the total fuel used and

the distance since the last average con-

sumption reset. The total fuel used is cal-

culated from the fuel consumption input.

For an accurate calculation, drive more

than 50 m (0.03 mile).

The meter's working range is from 0.1 to

99.9 l/100 km (0.1 to 99.9 miles per gal-

lon).

Pressing the TRIP button for more than 1

second, when the average fuel consump-

tion is being displayed, clears the aver-

age fuel consumption to zero (---).

4 39

Features of your vehicle

D150300AFD-EA

D150302AFD-EA

Air bag warning light

(if equipped)

Warnings and indicators

All warning lights are checked by turning

the ignition switch ON (do not start the

engine). Any light that does not illuminate

should be checked by an authorised

HYUNDAI dealer.

After starting the engine, check to make

sure that all warning lights are off. If any

are still on, this indicates a situation that

needs attention. When releasing the

hand brake, the brake system warning

light should go off. The fuel warning light

will stay on if the fuel level is low.

This warning light will illuminate for

approximately 6 seconds each time you

turn the ignition switch to the ON posi-

tion.

This light also comes on when the SRS

is not working properly. If the AIRBAG

warning light does not come on, or con-

tinuously remains on after operating for

about 6 seconds when you turned the

ignition switch to the ON position or start-

ed the engine, or if it comes on while

driving, have the SRS inspected by an

authorised HYUNDAI dealer.

Tripmeter

Odometer

OFD047049

Tripmeter (km or MI)

This mode indicates the distance of indi-

vidual trip since the last tripmeter reset.

The meter's working range is from 0.0 to

999.9 km (miles).

Pressing the TRIP button for more than 1

second when the tripmeter is being dis-

played clears the tripmeter to zero (0.0).

4 40

Features of your vehicle

D150303AFD-EA

D150304AFD-EA

Electronic brake force distri-

bution (EBD) system warning

light

Anti-lock brake system

(ABS) warning light

(if equipped)

Seat belt warning

This light illuminates if the ignition switch

is turned to ON and goes off in approxi-

mately 3 seconds if the system is operat-

ing normally.

If the ABS warning light remains on,

comes on while driving, or does not

come on when the ignition switch is

turned to the ON position, this indicates

that there may be a problem with the

ABS.

If this occurs, have your vehicle checked

by an authorised HYUNDAI dealer as

soon as possible. The normal braking

system will still be operational, but with-

out the assistance of the anti-lock brake

system.

As a reminder to the driver and front pas-

senger, the driver’s and front passenger’s

seat belt warning lights will illuminate for

approximately 6 seconds each time you

turn the ignition switch ON, regardless of

belt fastening.

If the driver’s or front passenger’s seat

belt is not fastened when the ignition

switch is turned ON or if it is disconnect-

ed after the ignition switch is turn ON, the

corresponding seat belt warning light will

illuminate or blink until the belt is fas-

tened.

If the driver's or front passenger’s seat

belt is not fastened when the ignition

switch is turned ON and you drive over

20 km/h, the seat belt warning chime will

sound for approximately 100 seconds.

If the driver's or front passenger’s seat

belt is disconnected after the ignition

switch is turn ON and you drive over 20

km/h, the seat belt warning chime will

sound for approximately 100 seconds.

If these two warning lights illuminate at

the same time while driving, your vehicle

may have a malfunction with ABS and

EBD system.

In this case, your ABS and regular brake

system may not work normally. Have the

vehicle checked by an authorised

HYUNDAI dealer as soon as possible.

WARNING

If the both ABS and Brake warning

lights are on and stay on, your vehi-

cle’s brake system will not work

normally. So you may experience

an unexpected and dangerous situ-

ation during sudden braking. In this

case, avoid high speed driving and

abrupt braking. Have your vehicle

checked

by

an

authorised

After 100 seconds, if the seat belt is con-

nected and disconnected again, the seat

belt warning chime will sound again.

HYUNDAI dealer as soon as possi-

ble.

4 41

Features of your vehicle

D150305AFD

D150307AFD-EA

CAUTION

Turn signal indicator lights

Engine oil pressure warning

If the oil pressure warning light

stays on while the engine is run-

ning, serious engine damage may

result. The oil pressure warning

light comes on whenever there is

insufficient oil pressure. In normal

operation, it should come on when

the ignition switch is turned on,

then go out when the engine is

started. If the oil pressure warning

light stays on while the engine is

running, there is a serious malfunc-

tion.

If this happens, stop the car as

soon as it is safe to do so, turn off

the engine and check the oil level. If

the oil level is low, fill the engine oil

to the proper level and start the

engine again. If the light stays on

with the engine running, turn the

engine off immediately. In any

instance where the oil light stays on

when the engine is running, the

engine should be checked by an

authorised HYUNDAI dealer before

the car is driven again.

This warning light indicates

the engine oil pressure is low.

If the warning light illuminates while driv-

ing:

1. Drive safely to the side of the road and

stop.

2. With the engine off, check the engine

oil level. If the level is low, add oil as

required.

The blinking green arrows on the instru-

ment panel show the direction indicated

by the turn signals. If the arrow comes on

but does not blink, blinks more rapidly

than normal, or does not illuminate at all,

a malfunction in the turn signal system is

indicated. Your dealer should be consult-

ed for repairs.

This indicator also blinks when the haz-

ard warning switch is turned on.

If the warning light remains on after

adding oil or if oil is not available, call an

authorised HYUNDAI dealer.

D150306AUN

High beam indicator

CAUTION

This indicator illuminates when the head-

lights are on and in the high beam posi-

tion or when the turn signal lever is pulled

into the Flash-to-Pass position.

If the engine is not stopped imme-

diately after the engine oil pressure

warning light is illuminated, severe

damage could result.

4 42

Features of your vehicle

D150308AFD-EA

D150309AUN

Your vehicle is equipped with dual-diago-

nal braking systems. This means you still

have braking on two wheels even if one

of the dual systems should fail. With only

one of the dual systems working, more

than normal pedal travel and greater

pedal pressure are required to stop the

car. Also, the car will not stop in as short

a distance with only a portion of the

brake system working. If the brakes fail

while you are driving, shift to a lower gear

for additional engine braking and stop the

car as soon as it is safe to do so.

Hand brake & brake fluid

warning

Front fog light indicator

(if equipped)

Hand brake warning

This light comes on when the front fog

lights are ON.

This light is illuminated when the hand

brake is applied with the ignition switch in

the START or ON position. The warning

light should go off when the hand brake

is released.

D150310AFD

Rear fog light Indicator

(if equipped)

Low brake fluid level warning

If the warning light remains on, it may

indicate that the brake fluid level in the

reservoir is low.

If the warning light remains on:

1. Drive carefully to the nearest safe

location and stop your vehicle.

This light comes on when the rear fog

lights are ON.

To check bulb operation, check whether

the hand brake and brake fluid warning

light illuminates when the ignition switch

is in the ON position.

D150312AUN

Shift pattern indicators

(if equipped)

2. With the engine stopped, check the

brake fluid level immediately and add

fluid as required. Then check all brake

components for fluid leaks.

3. Do not drive the vehicle if leaks are

found, the warning light remains on or

the brakes do not operate properly.

Have it towed to any authorised

HYUNDAI dealer for a brake system

inspection and necessary repairs.

WARNING

The indicator displays which automatic

transaxle shift position is selected.

Driving the vehicle with a warning

light on is dangerous. If the brake

warning light remains on, have the

brakes checked and repaired imme-

diately by an authorised HYUNDAI

dealer.

4 43

Features of your vehicle

D150313AFD-EA

D150316AUN

D150319AUN

Door ajar warning light

Charging system warning

Low washer fluid level

warning indicator

(if equipped)

This warning light indicates the washer

fluid reservoir is near empty. Refill the

washer fluid as soon as possible.

This warning light illuminates when a

door is not closed securely with the igni-

tion in any position.

This warning light indicates a malfunction

of either the generator or electrical

charging system.

If the warning light comes on while the

vehicle is in motion:

1. Drive to the nearest safe location.

D150320AFD-EA

D150317AFD-EA

Immobiliser indicator

(if equipped)

Malfunction indicator lamp

(MIL) (check engine light)

2. With the engine off, check the genera-

tor drive belt for looseness or break-

age.

3. If the belt is adjusted properly, a prob-

lem exists somewhere in the electrical

charging system. Have an authorised

HYUNDAI dealer correct the problem

as soon as possible.

This light illuminates when the immobilis-

er key is inserted and turned to the ON

position to start the engine.

At this time, you can start the engine.The

light goes out after the engine is running.

If this light blinks when the ignition switch

is in the ON position before starting the

engine, have the system checked by an

authorised HYUNDAI dealer.

This indicator light is part of the Engine

Control System which monitors various

emission control system components. If

this light illuminates while driving, it indi-

cates that a potential problem has been

detected somewhere in the emission

control system.

This light will also illuminate when the

ignition switch is turned to the ON posi-

tion, and will go out in a few seconds

after the engine is started. If it illuminates

while driving, or does not illuminate when

the ignition key is turned to the ON posi-

tion, take your vehicle to your nearest

authorised HYUNDAI dealer and have

the system checked.

D150315AUN

Tailgate open warning light

D150318AFD

Low fuel level warning

This warning light blinks when the tail-

gate is not closed securely with the igni-

tion in any position.

This warning light indicates the fuel tank

is nearly empty. When it comes on, you

should add fuel as soon as possible.

Driving with the fuel level warning light on

or with the fuel level below “E” (or 0) can

cause the engine to misfire and damage

the catalytic converter.

Generally, your vehicle will continue to be

drivable, but have the system checked by

an authorised HYUNDAI dealer promptly.

4 44

Features of your vehicle

D150323AUN-EE

CAUTION

CAUTION - Diesel engine

(if equipped with DPF)

ESP indicator (Electronic

Stability Program)

(if equipped)

ESP

• Prolonged driving with the

Emission

Control

System

When the malfunction indicator

light is blinks, it may stop blinking

after driving the vehicle at more

than 60km/h (37 mph) or at more

than second gear with 1500 ~ 2000

engine rpm for a certain time (for

about 25 minutes).

If the malfunction indicator light

continues to be blinked in spite of

the procedure, please visit an

authorised HYUNDAI dealer and

then check the DPF system.

If you continue to drive with the

malfunction indicator light blinking

for a long time, the DPF system can

be damaged and fuel consumption

can be worsen.

Malfunction Indicator Light illumi-

nated may cause damage to the

emission control systems which

could effect drivability and/or fuel

economy.

If the Emission Control System

Malfunction Indicator Light illumi-

nates, potential catalytic converter

damage is possible. This could

result in loss of engine power.

Have the Engine Control System

inspected as soon as possible by

an authorised HYUNDAI dealer.

The ESP indicator will illuminate when

the ignition switch is turned ON, but

should go off after approximately 3 sec-

onds.When the ESP is on, it monitors the

driving conditions and under normal driv-

ing conditions, the ESP light will remain

off. When a slippery or low traction con-

dition is encountered, the ESP will oper-

ate, and the ESP indicator will blink to

indicate the ESP is operating.

•

4 45

Features of your vehicle

D150324AFD-EA

D150325AFD

D150327AUN

ESP

OFF

ESP OFF indicator

(if equipped)

Cruise indicator (if equipped)

CRUISE indicator

Key reminder warning chime

(if equipped)

If the driver’s door is opened while the

ignition key is left in the ignition switch

(ACC or LOCK position), the key

reminder warning chime will sound. This

is to prevent you from locking your keys

in the vehicle.The chime sounds until the

key is removed from the ignition switch or

the driver’s door is closed.

CRUISE

The ESP OFF indicator will illuminate

when the ignition switch is turned ON,

but should go off after approximately 3

seconds. To switch to ESP OFF mode,

press the ESP OFF button. The ESP

OFF indicator will illuminate indicating

the ESP is deactivated. If this indicator

stays on when ESP OFF is not selected,

the ESP may have a malfunction. Take

your car to an authorised HYUNDAI deal-

er and have the system checked.

The indicator light illuminates when the

cruise control system is enabled.

The cruise indicator light in the instru-

ment cluster is illuminated when the

cruise control ON/OFF button on the

steering wheel is pushed.

The indicator light turns off when the

cruise control ON/OFF button is pushed

again. For more Information about the

use of cruise control, refer to section 5,

“Cruise control system”.

✽

NOTICE

After reconnecting or recharging a dis-

charged battery, the ESP OFF indicator

may illuminate. In this case, turn the

steering wheel 360 degrees to the left

and 360 degrees to the right while the

ignition switch is in the ON position.

Then, restart the engine after the igni-

tion is off. If the ESP OFF indicator does

not turn off, have the system checked by

an authorised HYUNDAI dealer as soon

as possible.

Cruise SET indicator

SET

The indicator light illuminates when the

cruise function switch (COAST/SET or

RES/ACCEL) is ON.

The cruise SET indicator light in the

instrument cluster is illuminated when

the cruise control switch (COAST/SET or

RES/ACCEL) is pushed. The cruise SET

indicator light does not illuminate when

the cruise control switch (CANCEL) is

pushed or the system is disengaged.

4 46

Features of your vehicle

D150328AFD-EA

D150329AFD-EA

D150334AFD-EA

Glow indicator

(Diesel engine)

Fuel filter warning light

(Diesel engine)

Electric power steering

(EPS) system warning light

EPS

The indicator light illuminates when the

ignition switch is placed at the ON posi-

tion. The engine can be started after the

preheat indicator light goes off. The illu-

minating time varies with the water tem-

perature, air temperature and battery

condition.

This warning light illuminates for 3 sec-

onds after the ignition switch is set to the

ON position and then it will go out. If it

lights up while the engine is running, it

indicates that water has accumulated

inside the fuel filter. If this happens,

remove the water from the fuel filter. For

more Information, refer to section 7,

“Fuel filter”.

This indicator light comes on after the

ignition key is turned to the ON position

and then it will go out after the engine is

started.

This light also comes on when the EPS

has some troubles. If it comes on while

driving, have your vehicle inspected by

an authorised HYUNDAI dealer.

✽

NOTICE

If the engine was not started within 10

seconds after the preheating is complet-

ed, turn the ignition key once more to

the LOCK position during 10 seconds,

and then to the ON position, in order to

preheat again.

CAUTION

When the fuel filter warning light is

illuminated, engine power (vehicle

speed & idle speed) may decrease.

If you keep driving with the warning

light on, you can damage your vehi-

cle's engine parts and injection sys-

tem of the Common Rail. If this

occurs, have your vehicle checked

by an authorised HYUNDAI dealer

as soon as possible.

CAUTION

If the preheat indicator light contin-

ues to illuminate or flash on and off

after the engine has warmed up or

while driving, check the system by

an authorised HYUNDAI dealer as

soon as possible.

4 47

Features of your vehicle

REAR PARKING ASSIST SYSTEM (IF EQUIPPED)

D170102AEN

Types of warning sound

WARNING

• When an object is 120 cm to 81 cm (47

in. to 32 in.) from the rear bumper:

Buzzer beeps intermittently.

• When an object is 80 cm to 41 cm (31

in. to 16 in.) from the rear bumper:

Buzzer beeps more frequently.

• When an object is within 40 cm (15 in.)

of the rear bumper:

Buzzer sounds continuously.

The rear parking assist system is a

supplementary function only. The

operation of the rear parking assist

system can be affected by several

factors (including environmental

conditions). It is the responsibility

of the driver to always check the

area behind the vehicle before and

while backing up.

Sensors

OFD047050

D170200AEN

Operation of the rear parking

assist system

D170000AEN

Non-operational conditions of

rear parking assist system

The rear parking assist system may

not operate properly when:

1. Moisture is frozen to the sensor. (It will

operate normally when the moisture

has been cleared.)

2. The sensor is covered with foreign

matter, such as snow or water, or the

sensor cover is blocked. (It will operate

normally when the material is removed

or the sensor is no longer blocked.)

The rear parking assist system assists

the driver during backward movement of

the vehicle by chiming if any object is

sensed within a distance of 120 cm (47

in.) behind the vehicle. This system is a

supplemental system and it is not intend-

ed to nor does it replace the need for

extreme care and attention of the driver.

The sensing range and objects

detectable by the back sensors are limit-

ed. Whenever backing-up, pay as much

attention to what is behind you as you

would in a vehicle without a rear parking

assist system.

D170101AEN

Operating condition

• This system will activate when backing

up with the ignition switch ON.

If the vehicle is moving at a speed over

5 km/h (3 mph), the system may not be

activated correctly.

• The sensing distance while the rear

parking assist system is in operation is

approximately 120 cm (47 in.).

• When more than two objects are

sensed at the same time, the closest

one will be recognized first.

3. Driving on uneven road surfaces

(unpaved roads, gravel, bumps, gradi-

ent).

4. Objects generating excessive noise

(vehicle horns, loud motorcycle

engines, or truck air brakes) are within

range of the sensor.

4 48

Features of your vehicle

D170300AEN

5. Heavy rain or water spray exists.

6. Wireless transmitters or mobile phones

are within range of the sensor.

7. The sensor is covered with snow.

8. Trailer towing

✽

NOTICE

Rear parking assist system pre-

cautions

• The rear parking assist system may

not sound sequentially depending on

the speed and shapes of the objects

detected.

• The rear parking assist system may

malfunction if the vehicle bumper

height or sensor installation has been

modified or damaged. Any non-factory

installed equipment or accessories

may also interfere with the sensor per-

formance.

• The sensor may not recognize objects

less than 40 cm (15 in.) from the sen-

sor, or it may sense an incorrect dis-

tance. Use caution.

This system can only sense objects with-

in the range and location of the sensors;

It can not detect objects in other areas

where sensors are not installed. Also,

small or slim objects, such as poles or

objects located between sensors may not

be detected by the sensors.

The detecting range may decrease

when:

1. The sensor is stained with foreign mat-

ter such as snow or water. (The sens-

ing range will return to normal when

removed.)

Always visually check behind the vehi-

cle when backing up.

Be sure to inform any drivers of the

vehicle that may be unfamiliar with the

system regarding the systems capabili-

ties and limitations.

2. Outside air temperature is extremely

hot or cold.

The following objects may not be rec-

ognized by the sensor:

1. Sharp or slim objects such as ropes,

chains or small poles.

2. Objects which tend to absorb the sen-

sor frequency such as clothes, spongy

material or snow.

3. Undetectable objects smaller than 1 m

(40 in.) in height and narrower than 14

cm (6 in.) in diameter.

WARNING

Pay close attention when the vehi-

cle is driven close to objects on the

road, particularly pedestrians, and

especially children. Be aware that

some objects may not be detected

by the sensors, due to the object’s

distance, size or material, all of

which can limit the effectiveness of

the sensor. Always perform a visu-

al inspection to make sure the vehi-

cle is clear of all obstructions

before moving the vehicle in any

direction.

• When the sensor is frozen or stained

with snow, dirt, or water, the sensor

may be inoperative until the stains are

removed using a soft cloth.

• Do not push, scratch or strike the sen-

sor. Sensor damage could occur.

4 49

Features of your vehicle

HAZARD WARNING FLASHER

D170400AFD-EA

The hazard warning lights are turned on

by pushing in the hazard switch. This

causes all turn signal lights to blink. The

hazard warning lights will operate even

though the key is not in the ignition

switch.

Type A

Self-diagnosis

If you don’t hear an audible warning

sound or if the buzzer sounds intermit-

tently when shifting the gear to the R

(Reverse) position, this may indicate a

malfunction in the rear parking assist sys-

tem. If this occurs, have your vehicle

checked by an authorised HYUNDAI

dealer as soon as possible.

To turn the hazard warning lights off,

push the switch a second time.

OFD067001R

Type B

WARNING

Your new vehicle warranty does not

cover any accidents or damage to

the vehicle or injuries to its occu-

pants due to a rear parking assist

system malfunction. Always drive

safely and cautiously.

OFD067002

D180000AUN

The hazard warning flasher should be

used whenever you find it necessary to

stop the car in a hazardous location.

When you must make such an emer-

gency stop, always pull off the road as far

as possible.

4 50

Features of your vehicle

LIGHTING

D190100AUN-EA

Type A

CAUTION

Battery saver function

If the driver gets out of the vehicle

through other doors (except driver's

door), the battery saver function

does not operate and the headlight

escort function does not turn off

automatically. Therefore, it causes

the battery to be discharged. In this

case, make sure to turn off the lamp

before getting out of the vehicle.

• The purpose of this feature is to pre-

vent the battery from being accidental-

ly discharged.The system automatical-

ly turns off the parking lights when the

driver removes the ignition key and

opens the driver’s door.

• If required, to keep the parking lights

on when the ignition key is removed,

perform the following :

OFD048051R

1) Open the driver’s door.

Type B

2) Turn the parking lights OFF and ON

again using the light switch on the

steering column.

Headlight welcome function

(if equipped)

If you press the door unlock button on the

transmitter when the light switch is in the

headlight or AUTO (in the dark outside)

position and all doors (and tailgate) are

closed, the headlight will come on for

about 15 seconds. At this time, if you

press the door lock or unlock button on

the transmitter, the headlights will turn off

immediately.

Headlight escort function

(if equipped)

If you turn the ignition switch to the ACC

or LOCK position with the headlights ON,

the headlights remain on for about 20

minutes. However, if the driver's door is

opened and closed, the headlights are

turned off after 30 seconds.

OFD049051R

D190400AUN

Lighting control

The headlights can be turned off by

pressing the lock button on the transmit-

ter twice or turning the light switch to the

OFF position.

For deactivation or activation of this fea-

ture, contact an authorized HYUNDAI

dealer.

The light switch has a Headlight and a

Parking light position. To operate the

lights, turn the knob at the end of the con-

trol lever to one of the following positions:

(1) OFF position

(2) Parking light position

(3) Headlight position

(4) Auto light position (if equipped)

4 51

Features of your vehicle

Type A

OFD048052R

OFD048053R

OFD048054R

Type B

OFD049052R

OFD049053R

OFD049054R

D190401AUN

D190402AUN

D190403AUN

Headlight position (

)

Parking light position (

)

Auto light position (if equipped)

or

When the light switch is in the headlight

position (2nd position) the head, tail,

position, license and instrument panel

lights are ON.

When the light switch is in the parking

light position (1st position), the tail, posi-

tion, license and instrument panel lights

are ON.

When the light switch is in the AUTO light

position, the taillights and headlights will

be turned ON or OFF automatically

depending on the amount of light outside

the vehicle.

✽

NOTICE

The ignition switch must be in the ON

position to turn on the headlights.

4 52

Features of your vehicle

Type A

CAUTION

• Never place anything over sensor

(1) located on the instrument

panel, this will ensure better auto-

light system control.

• Don’t clean the sensor using a

window cleaner, the cleaner may

leave a light film which could

interfere with sensor operation.

• If your vehicle has window tint or

other types of metallic coating on

the front windshield, the Auto

light system may not work prop-

erly.

OFD048055R

OFD048056R

Type B

OFD049055R

OFD049056R

D190500AUN

Flashing headlights

High - beam operation

To flash the headlights, pull the lever

towards you. It will return to the normal

(low-beam) position when released. The

headlight switch does not need to be on

to use this flashing feature.

To turn on the high beam headlights,

push the lever away from you. Pull it back

for low beams. The high-beam indicator

will light when the headlight high beams

are switched on. To prevent the battery

from being discharged, do not leave the

lights on for a prolonged time while the

engine is not running.

4 53

Features of your vehicle

They will self-cancel after a turn is com-

pleted. If the indicator continues to flash

after a turn, manually return the lever to

the OFF position.

Type A

To signal a lane change, move the turn

signal lever slightly and hold it in position

(B). The lever will return to the OFF posi-

tion when released.

If an indicator stays on and does not

flash or if it flashes abnormally, one of the

turn signal bulbs may be burned out and

will require replacement.

OFD048057R

OFD048058R

Type B

One-touch triple turn signal

(if equipped)

To activate an one-touch triple turn signal

move the turn signal lever slightly and

then release it. The lane change signals

will blink 3 times.

✽

NOTICE

If an indicator flash is abnormally quick

or slow, bulb may be burned out or have

a poor electrical connection in the cir-

cuit.

OFD049057R

OFD049058R

D190600AUN

D190700AFD

Front fog light (if equipped)

Turn signals and lane change sig-

nals

Fog lights are used to provide improved

visibility and avoid accidents when visibil-

ity is poor due to fog, rain or snow etc.

The fog lights will turn on when fog light

switch (1) is turned to on position (2) after

the parklight is turned on.

The ignition switch must be on for the

turn signals to function. To turn on the

turn signals, move the lever up or down

(A). Green arrow indicators on the instru-

ment panel indicate which turn signal is

operating.

To turn off the fog lights, turn the switch

to on position (2) again.

4 54

Features of your vehicle

The rear fog lights turn on when the rear

fog light switch is turned on after the front

fog light switch is turned on and the

headlight switch to the parklight position.

To turn the rear fog lights off, turn the rear

fog light switch to the on position again or

turn the headlight switch off.

Type A

CAUTION

When in operation, the fog lights

consume large amounts of vehicle

electrical power. Only use the fog

lights when visibility is poor.

OFD048059R

Type B

OFD049059R

D190800AFD

Rear fog light (if equipped)

To turn the rear fog lights on, turn the

headlight switch to the headlight on posi-

tion and turn the rear fog light switch to

the on position (3).

4 55

Features of your vehicle

WIPERS AND WASHERS

Windshield wiper/washer

A : Wiper speed control

· MIST – Single wipe

· OFF – Off

Rear window wiper/washer

(if equipped)

Type A

· INT / AUTO – Intermittent wipe/

Auto control wipe*

· LO – Normal wiper speed

· HI – Fast wiper speed

B : Intermittent or Auto control wipe

time adjustment

C : Wash with brief wipes

Type B

D : Rear wiper/washer control

·

– Spraying washer fluid

· ON – Normal wipe operation

· OFF – Off

·

– Wash with brief wipes

*: if equipped

OFD047900R/OFD049900R/OFD0489001R/OFD0499001R

4 56

Features of your vehicle

MIST

: For a single wiping cycle, push

the lever upward and release it

with the lever in the OFF posi-

tion. The wipers will operate

continuously if the lever is

pushed upward and held.

Type A

OFF : Wiper is not in operation.

INT / AUTO* : Wiper operates intermit-

tently at the same wiping

intervals. Use this mode in

a light rain or mist. To vary

the speed setting, turn the

speed control knob(1).

OFD048904R

OFD047901R-1

Type B

LO : Normal wiper speed

HI : Fast wiper speed

✽

NOTICE

If there is heavy accumulation of snow

or ice on the windshield, defrost the

windshield for about 10 minutes, or

until the snow and/or ice is removed

before using the windshield wipers to

ensure proper operation.

OFD049904R

OFD049901R-1

D200100AFD

D200101AEN

Windshield wipers

Auto control (if equipped)

The rain sensor located on the upper end

of the windshield glass senses the

amount of rainfall and controls the wiping

cycle for the proper interval. The more it

rains, the faster the wiper operates.

When the rain stops, the wiper stops. To

vary the speed setting, turn the speed

control knob (1).

Operates as follows when the ignition

switch is turned ON.

4 57

Features of your vehicle

If the ignition switch is turned ON when

the wiper switch is set in AUTO mode, or

the wiper switch is set in AUTO mode

when the ignition switch is ON, or the

speed control knob is turned upward

when the wiper switch is in AUTO mode,

the wiper will operate once to perform a

self-check of the system. Set the wiper to

0 position when the wiper is not in use.

Type A

CAUTION

When washing the vehicle, set the

wiper switch in the OFF position to

stop the auto wiper operation.

The wiper may operate and be dam-

aged if the switch is set in the AUTO

mode while washing the vehicle.

Do not remove the sensor cover

located on the upper end of the pas-

senger side windshield glass.

Damage to system parts could

occur and may not be covered by

your vehicle warranty.

When starting the vehicle in winter,

set the wiper switch in the OFF

position. Otherwise, wipers may

operate and ice may damage the

windshield wiper blades. Always

remove all snow and ice and defrost

the windshield properly prior to

operating the windshield wipers.

OFD048902R

CAUTION

Type B

When the ignition switch is ON and

the windshield wiper switch is

placed in the AUTO mode, use cau-

tion in the following situations to

avoid any injury to the hands or

other parts of the body:

• Do not touch the upper end of the

windshield glass facing the rain

sensor.

• Do not wipe the upper end of the

windshield glass with a damp or

wet cloth.

OFD049902R

D200200AUN-EA

Windshield washers

• Do not put pressure on the wind-

shield glass.

In the OFF position, pull the lever gently

toward you to spray washer fluid on the

windshield and to run the wipers 1-3

cycles.

Use this function when the windshield is

dirty.

4 58

Features of your vehicle

The spray and wiper operation will con-

tinue until you release the lever.

Type A

CAUTION

• To prevent possible damage to

the wipers or windshield, do not

operate the wipers when the

windshield is dry.

• To prevent damage to the wiper

blades, do not use petrol,

kerosene, paint thinner, or other

solvents on or near them.

If the washer does not work, check the

washer fluid level. If the fluid level is not

sufficient, you will need to add appropri-

ate non-abrasive windshield washer fluid

to the washer reservoir.

The reservoir filler neck is located in the

front of the engine compartment on the

driver side.

OFD048903R

Type B

• To prevent damage to the wiper

arms and other components, do

not attempt to move the wipers

manually.

CAUTION

To prevent possible damage to the

washer pump, do not operate the

washer when the fluid reservoir is

empty.

OFD049903R

D200300AFD

WARNING

Rear window wiper and washer

switch (if equipped)

The rear window wiper and washer

switch is located at the end of the wiper

and washer switch lever. Turn the switch

to desired position to operate the rear

wiper and washer.

Do not use the washer in freezing

temperatures without first warming

the windshield with the defrosters;

the washer solution could freeze on

contact with the windshield and

obscure your vision.

- Spraying washer fluid and wiping

ON - Normal wiper operation

OFF - Wiper is not in operation

- Spraying washer fluid and wiping

4 59

Features of your vehicle

INTERIOR LIGHT

D210000AUN

• DOOR (2) :

In the DOOR position, the light comes on

when any door is opened regardless of

the ignition switch position.

CAUTION

Do not use the interior lights for

extended periods when engine is

not running.

When doors are unlocked by the trans-

mitter, the light comes on for approxi-

mately 30 seconds as long as any door is

not open. The light goes out gradually

after approximately 30 seconds if the

door is closed. However, if the ignition

switch is ON or all doors are locked, the

light will turn off immediately.

If a door is opened with the ignition

switch in the ACC or LOCK position, the

light stays on for about 20 minutes.

However, if a door is opened with the

ignition switch in the ON position, the

light stays on continuously.

It may cause battery discharge.

OFD047067

D210100AFD

Map lamp (if equipped)

Push in the map lamp lens (1) to turn the

light on or off. This light produces a spot

beam for convenient use as a map lamp

at night or as a personal lamp for the

driver and the passenger.

4 60

Features of your vehicle

• DOOR (2) :

In the DOOR position, the light comes on

when any door is opened regardless of

the ignition switch position.

When doors are unlocked by the trans-

mitter, the light comes on for approxi-

mately 30 seconds as long as any door is

not open. The light goes out gradually

after approximately 30 seconds if the

door is closed. However, if the ignition

switch is ON or all doors are locked, the

light will turn off immediately.

If a door is opened with the ignition

switch in the ACC or LOCK position, the

light stays on for about 20 minutes.

However, if a door is opened with the

ignition switch in the ON position, the

light stays on continuously.

1

2

3

Wagon

5 Door

OFD047068

OFD047130L

D210200AFD

D210300AFD

Dome lamp

• OFF (1) :

Luggage room lamp

The luggage room lamp comes on when

the tailgate is opened.

In the OFF position, the light stays off at

all times even when a door is open.

• ON (3):

In the ON position, the light stays on at all

times.

CAUTION

Do not leave the switch in this posi-

tion for an extended period of time

when the vehicle is not running.

4 61

Features of your vehicle

DEFROSTER

D220000AUN

CAUTION

To prevent damage to the conduc-

tors bonded to the inside surface of

the rear window, never use sharp

instruments or window cleaners

containing abrasives to clean the

window.

✽

NOTICE

OFD047069R

OFD047070R

If you want to defrost and defog on the

front windshield, refer to “Windshield

Defrosting and Defogging” in this sec-

tion.

D210500AUN

D210600AUN

Glove box lamp (if equipped)

The glove box lamp comes on when the

glove box is opened.

Vanity mirror lamp (if equipped)

Opening the lid of the vanity mirror will

automatically turn on the mirror light.

The parking lights or headlights must be

ON for the glove box lamp to function.

4 62

Features of your vehicle

Type A

The defroster heats the window to

remove frost, fog and thin ice from the

interior and exterior of the rear window,

while engine is running.

To activate the rear window defroster,

press the rear window defroster button

located in the centre facia switch panel.

The indicator on the rear window

defroster button illuminates when the

defroster is ON.

If there is heavy accumulation of snow on

the rear window, brush it off before oper-

ating the rear defroster.

The rear window defroster automatically

turns off after approximately 20 minutes

or when the ignition switch is turned off.

To turn off the defroster, press the rear

window defroster button again.

OFD040071

OFD047072

OFD047072K

Type B

OFD047073R

D220200AUN

Front windshield deicer

(if equipped)

The engine must be running to enable

this feature. To activate the front wind-

shield deicer, press the front windshield

deicer button. The indicator on the button

illuminates when the deicer is ON. The

front windshield deicer automatically

turns off after 20 minutes or when the

ignition switch is turned off.To turn off the

deicer, press the front windshield deicer

button again.

D220101AUN

Type C

Outside mirror defroster

(if equipped)

If your vehicle is equipped with the out-

side mirror defrosters, they will operate at

the same time you turn on the rear win-

dow defroster.

D220100AUN-EA

Rear window defroster

4 63

Features of your vehicle

MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)

1. Temperature control knob

2. Fan speed control knob

3. Mode buttons

4. Air conditioning button (if equipped)

5. Air intake control buttons

6. Front window defroster button

7. Rear window defroster button

OFD040074

D230000AFD

4 64

Features of your vehicle

D230100AUN

Heating and air conditioning

1. Start the engine.

2. Set the mode to the desired position.

3. Set the temperature control to the

desired position.

4. Set the air intake control to the outside

(fresh) air position.

5. Set the fan speed control to the

desired speed.

6. If air conditioning is desired, turn the

air conditioning system (if equipped)

on.

OFD047076R

4 65

Features of your vehicle

Face-Level (B,D)

Floor-Level (C, E, A, D)

Most of the air flow is directed to the

floor, with a small amount of the air being

directed to the windshield and side win-

dow defroster.

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

Floor/Defrost-Level (A, C, E, D)

Bi-Level (B, D, C, E)

Most of the air flow is directed to the floor

and the windshield with a small amount

directed to the side window defrosters.

Air flow is discharged towards the face and

floor.

OFD040077

D230101AFD

Mode selection

The mode buttons control the direction of

the air flow through the ventilation sys-

tem.

Defrost-Level (A, D)

Air can be directed to the floor, dashboard

outlets, or windshield. Five symbols are

used to represent Face, Bi-Level, Floor,

Floor-Defrost and Defrost air position.

Most of the air flow is directed to the

windshield with a small amount of air

directed to the side window defrosters.

4 66

Features of your vehicle

OFD047079R

OFD047078

OFD040080

D230102AFD

D230103AFD

Instrument panel vents

Temperature control

Air intake control

This is used to select outside (fresh) air

position or recirculated air position.

To change the air intake control position,

push the control button.

The outlet port can be opened or closed

separately using the horizontal thumb-

wheel. To close the vent, rotate it left to

the maximum position. To open the vent,

rotate it right to the desired position.

The temperature control knob allows you

to control the temperature of the air flow-

ing from the ventilation system. To

change the air temperature in the pas-

senger compartment, turn the knob to

the right position for warm air or left posi-

tion for cooler air.

Also, you can adjust the direction of air

delivery from these vents using the vent

control lever as shown.

4 67

Features of your vehicle

Recirculated air position

✽

NOTICE

The indicator light on the

WARNING

Prolonged operation of the heater in the

recirculated air position (without air

conditioning selected) may cause fog-

ging of the windshield and side windows

and the air within the passenger com-

partment may become stale.

button is illuminated when

the recirculated air position

is selected.

With the recirculated air

position selected, air from

passenger compartment

will be drawn through the

heating system and heated

or cooled according to the

function selected.

• Continued use of the climate con-

trol system operation in the recir-

culated air position may allow

humidity to increase inside the

vehicle which may fog the glass

and obscure visibility.

In addition, prolonged use of the air

conditioning with the recirculated air

position selected will result in excessive-

ly dry air in the passenger compart-

ment.

• Do not sleep in a vehicle with the

air conditioning or heating sys-

tem on. It may cause serious

harm or death due to a drop in the

oxygen level and/or body temper-

ature.

Outside (fresh) air position

• Continued use of the climate con-

trol system operation in the recir-

culated air position can cause

drowsiness or sleepiness, and

loss of vehicle control. Set the air

intake control to the outside

(fresh) air position as much as

possible while driving.

The indicator light on the

button is illuminated when

the outside (fresh) air posi-

tion is selected.

With the outside (fresh) air

position selected, air enters

the vehicle from outside and

is heated or cooled accord-

ing to the function selected.

4 68

Features of your vehicle

System operation

D230501AUN

Ventilation

1. Set the mode to the

position.

2. Set the air intake control to the outside

(fresh) air position.

3. Set the temperature control to the

desired position.

4. Set the fan speed control to the

desired speed.

OFD047081

OFD047082

D230502AUN

D230104AUN

D230105AUN

Heating

Fan speed control

Air conditioning (if equipped)

1. Set the mode to the

position.

The ignition switch must be in the ON

position for fan operation.

The fan speed control knob allows you to

control the fan speed of the air flowing

from the ventilation system. To change

the fan speed, turn the knob to the right

for higher speed or left for lower speed.

Push the A/C button to turn the air condi-

tioning system on (indicator light will illu-

minate). Push the button again to turn the

air conditioning system off.

2. Set the air intake control to the outside

(fresh) air position.

3. Set the temperature control to the

desired position.

4. Set the fan speed control to the

desired speed.

5. If dehumidified heating is desired, turn

the air conditioning system (if

equipped) on.

Setting the fan speed control knob to the

“0” position turns off the fan.

• If the windshield fogs up, set the mode

to the

,

position.

4 69

Features of your vehicle

D230503AFD

Operation Tips

✽

NOTICE

Air conditioning (if equipped)

• To keep dust or unpleasant fumes from

entering the car through the ventilation

system, temporarily set the air intake

control to the recirculated air position.

Be sure to return the control to the

fresh air position when the irritation

has passed to keep fresh air in the

vehicle. This will help keep the driver

alert and comfortable.

• When using the air conditioning sys-

tem, monitor the temperature gauge

closely while driving up hills or in

heavy traffic when outside tempera-

tures are high. Air conditioning sys-

tem operation may cause engine over-

heating. Continue to use the blower

fan but turn the air conditioning sys-

tem off if the temperature gauge indi-

cates engine overheating.

All HYUNDAI Air Conditioning Systems

are filled with environmentally friendly

R-134a refrigerant which does not dam-

age to the ozone layer.

1. Start the engine. Push the air condi-

tioning button.

2. Set the mode to the

3. Set the air intake control to the outside

air or recirculated air position.

4. Adjust the fan speed control and tem-

perature control to maintain maximum

comfort.

• When maximum cooling is desired, set

the temperature control to the extreme

left position then set the fan speed

control to the highest speed.

position.

• Air for the heating/cooling system is

drawn in through the grilles just ahead

of the windshield. Care should be

taken that these are not blocked by

leaves, snow, ice or other obstructions.

• To prevent interior fog on the wind-

shield, set the air intake control to the

fresh air position and fan speed to the

desired position, turn on the air condi-

tioning system, and adjust temperature

control to desired temperature.

• When opening the windows in humid

weather air conditioning may create

water droplets inside the vehicle.

Since excessive water droplets may

cause damage to electrical equipment,

air conditioning should only be run

with the windows closed.

4 70

Features of your vehicle

Air conditioning system operation tips

✽

NOTICE

• If the vehicle has been parked in direct

sunlight during hot weather, open the

windows for a short time to let the hot

air inside the vehicle escape.

Outside air

• Replace the filter according to the

Maintenance Schedule.

If the car is being driven in severe

conditions such as dusty, rough roads,

more frequent climate control air fil-

ter inspections and changes are

required.

Recirculated

air

• To help reduce moisture inside of win-

dows on rainy or humid days, decrease

the humidity inside the vehicle by oper-

ating the air conditioning system.

• During air conditioning system opera-

tion, you may occasionally notice a

slight change in engine speed as the

air conditioning compressor cycles.

This is a normal system operation

characteristic.

• Use the air conditioning system every

month if only for a few minutes to

ensure maximum system performance.

• When using the air conditioning sys-

tem, you may notice clear water drip-

ping (or even puddling) on the ground

under the passenger side of the vehi-

cle. This is a normal system operation

characteristic.

• Operating the air conditioning system

in the recirculated air position provides

maximum cooling, however, continual

operation in this mode may cause the

air inside the vehicle to become stale.

• During cooling operation, you may

occasionally notice a misty air flow

because of rapid cooling and humid air

intake. This is a normal system opera-

tion characteristic.

• When the air flow rate is suddenly

decreased, the system should be

checked at an authorised HYUNDAI

dealer.

Blower

Heater core

Climate control

Evaporator

core

air filter

1LDA5047

D230300AFD-EA

Climate control air filter

(if equipped)

The climate control air filter installed

behind the glove box filters the dust or

other pollutants that come into the vehi-

cle from the outside through the heating

and air conditioning system. If dust or

other pollutants accumulate in the filter

over a period of time, the air flow from the

air vents may decrease, resulting in

moisture accumulation on the inside of

the windshield even when the outside

(fresh) air position is selected. If this hap-

pens, have the climate control air filter

replaced by an authorised HYUNDAI

dealer.

4 71

Features of your vehicle

D230400AFD-EA

Checking the amount of air con-

ditioner refrigerant and compres-

sor lubricant

When the amount of refrigerant is low,

the performance of the air conditioning is

reduced. Overfilling also has a bad influ-

ence on the air conditioning system.

Therefore, if abnormal operation is

found, have the system inspected by an

authorised HYUNDAI dealer.

✽

NOTICE

It is important when servicing the air

conditioning system that the correct

type and amount of oil and refrigerant is

used. Otherwise, damage to the com-

pressor and abnormal system operation

may occur.

WARNING

The air conditioning system should

be serviced by an authorised

HYUNDAI dealer. Improper service

may cause serious injury to the

person performing the service.

4 72

Features of your vehicle

AUTOMATIC CLIMATE CONTROL SYSTEM (IF EQUIPPED)

Type A

1. Fan speed control button

2. Air conditioning button

5. AUTO (automatic control) button

6. OFF button

9. Mode selection button

10. A/C display

3. Air intake control button

4. Front windshield defrost button

7. Temperature control knob

8. Rear window defrost button

OFD0471100

D240000AFD

4 73

Features of your vehicle

Type B

1. Fan speed control button

2. Air intake control button

4. OFF button

7. Air conditioning button

8. Mode selection button

9. A/C display

5. Temperature control knob

6. Front windshield defrost button

3. AUTO (automatic control) button

OFD0471101

4 74

Features of your vehicle

2. Turn the temperature control knob to

set the desired temperature.

If the temperature is set to the lowest

setting (Lo), the air conditioning sys-

tem will operate continuously.

3. To turn the automatic operation off,

press any button except temperature

control knob. If you press the mode

selection button, air-conditioning but-

ton*, defrost button, air intake control

button* or fan speed button, the select-

ed function will be controlled manually

while other functions operate automat-

ically. (* : type B only)

OFD047102

OUN026312

D240100AFD

✽

NOTICE

Automatic heating and air condi-

tioning

The automatic climate control system is

controlled by simply setting the desired

temperature.

The Full Automatic Temperature Control

(FATC) system automatically controls the

heating and cooling system as follows;

Never place anything over the sensor

located on the instrument panel to

ensure better control of the heating and

cooling system.

Regardless of the temperature setting,

when using automatic operation, the air

conditioning system can automatically

turn on to decrease the humidity inside

the vehicle, even if the temperature is set

to warm.

1. Push the AUTO button. It is indicated

by AUTO on the display. The modes,

fan speeds, air intake and air-condi-

tioning will be controlled automatically

by temperature setting.

4 75

Features of your vehicle

D240200AUN

Type A

Manual heating and air condition-

ing

Face-Level (B, D)

The heating and cooling system can be

controlled manually by pushing buttons

other than the AUTO button. In this case,

the system works sequentially according

to the order of buttons selected.

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

When pressing any button (or turning

any knob) except AUTO button while

automatic operation, the functions not

selected will be controlled automatically.

1. Start the engine.

2. Set the mode to the desired position.

3. Set the temperature control to the

desired position.

4. Set the air intake control to the outside

(fresh) air position.

5. Set the fan speed control to the

desired speed.

6. If air conditioning is desired, turn the

air conditioning system on.

Floor-Level (C, E, A, D)

Most of the air flow is directed to the

floor.

OFD047103

D240201AFD

Mode selection

Defrost-Level (A, D)

The mode selection button controls the

direction of the air flow through the venti-

lation system.

Refer to the illustration in the “Manual cli-

mate control system”.

Most of the air flow is directed to the

windshield.

Also you may select 2~3 modes at the

same time for desired air flow.

Type A :

- face (

- floor (

) + floor (

) mode

If you push the button once, the corre-

sponding switch will turn on, and if you

push the button again, the switch will turn

off.

Press the AUTO button in order to con-

vert to full automatic control of the sys-

tem.

) + defrost (

) + floor (

) mode

- face (

mode

) + defrost (

)

4 76

Features of your vehicle

Type B

Face-Level (B, D)

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

Bi-Level (B, D, C, E)

Air flow is discharged towards the face and

floor.

OFD047124

OFD047104

Maximum (MAX) defrost mode

Type B:

When you select the MAX defrost mode,

the following system settings will be

made automatically;

The air flow outlet port is converted as

follows:

Floor-Level (C, E, A, D)

• the air conditioning system will be

turned on.

• the outside(fresh) air position will be

selected.

• the fan speed will be set to the high

speed.

Most of the air flow is directed to the

floor, with a small amount of the air being

directed to the windshield and side win-

dow defroster.

To turn the MAX defrost mode off, press

Floor/Defrost-Level (A, C, E, D)

the mode button (

,

) or MAX

(

) defrost button again or AUTO but-

ton.

Most of the air flow is directed to the floor

and the windshield with a small amount

directed to the side window defrosters.

4 77

Features of your vehicle

OFD047105

OFD047079R

OFD047107

D240202AUN

Defrost-level (A, D)

Most of the air flow is directed to the

windshield with a small amount of air

directed to the side window defrosters.

Instrument panel vents

Temperature control

The outlet port can be opened or closed

separately using the horizontal thumb-

wheel. To close the vent, rotate it left to

the maximum position. To open the vent,

rotate it right to the desired position.

The temperature will increase to the

maximum (HI) by turning the knob to the

right extremely.

The temperature will decrease to the

minimum (Lo) by turning the knob to the

left extremely.

When turning the knob, the temperature

will increase or decrease by 0.5°C/1°F.

When set to the lowest temperature set-

ting, the air conditioning will operate con-

tinuously.

Also, you can adjust the direction of air

delivered from these vents using the vent

control lever as shown.

4 78

Features of your vehicle

Temperature conversion

If the battery has been discharged or dis-

connected, the temperature mode dis-

play will reset to Centigrade.

Recirculated air position

Type A

Type B

The indicator light on the

button illuminates when the

recirculated air position is

selected.

This is normal condition. You can switch

the

temperature

mode

between

With the recirculated air

position selected, air from

passenger compartment

will be drawn through the

heating system and heated

or cooled according to the

function selected.

Centigrade to Fahrenheit as follows;

While depressing the AUTO button,

depress the OFF button for 3 seconds or

more. The display will change from

Centigrade to Fahrenheit, or from

Fahrenheit to Centigrade.

OFD047108/OFD047109

D240203AFD

Outside (fresh) air position

Air intake control

This is used to select outside (fresh) air

position or recirculated air position.

To change the air intake control position,

push the control button.

The indicator light on the

button does not illuminate

when the outside (fresh) air

position is selected (type A).

With the outside (fresh) air

position selected, air enters

the vehicle from outside and

is heated or cooled accord-

ing to the function selected.

4 79

Features of your vehicle

✽

NOTICE

Type A

Type B

Type A

Type B

It should be noted that prolonged oper-

ation of the heating in recirculated air

position will cause fogging of the wind-

shield and side windows and the air

within the passenger compartment will

become stale.

In addition, prolonged use of the air con-

ditioning with the recirculated air posi-

tion selected, will result in excessively

dry air in the passenger compartment.

OFD047110/OFD047111

OFD047112/OFD047113

WARNING

D240205AUN

D240206AUN

• Continued use of the climate con-

trol system operation in the recir-

culated air position may allow

humidity to increase inside vehicle

which may fog the glass and

obscure visibility.

• Do not sleep in a vehicle with air

conditioning or heating system on.

It may cause serious harm or death

due to a drop in the oxygen level

and/or body temperature.

Fan speed control

Air conditioning

The fan speed can be set to the desired

speed by pressing the fan speed control

button.

The higher the fan speed is, the more air

is delivered.

Push the A/C button to turn the air condi-

tioning system on (indicator light will illu-

minate).

Push the button again to turn the air con-

ditioning system off.

Pressing the OFF button turns off the

fan.

• Continued use of the climate con-

trol system operation in the reciru-

clated air position can cause

drowsiness or sleepiness, and loss

of vehicle control. Set the air intake

control to the outside (fresh) air

position as much as possible while

driving.

4 80

Features of your vehicle

WINDSHIELD DEFROSTING AND DEFOGGING

D250000AUN-EA

WARNING - Windshield

heating

or

Do not use the

position

during cooling operation in

extremely humid weather. The dif-

ference between the temperature of

the outside air and that of the wind-

shield could cause the outer sur-

face of the windshield to fog up,

causing loss of visibility. In this

case, set the mode selection knob

OFD047114

OFD040115

D240208AUN

Manual climate control system

or button to the

position and

OFF mode

D250101AFD

fan speed control knob or button to

a lower speed.

Push the OFF button to turn off the air cli-

mate control system. However you can

still operate the mode and air intake but-

tons as long as the ignition switch is in

the position ON.

To defog inside windshield

1. Select any fan speed except “0” posi-

tion.

• For maximum defrosting, set the temper-

ature control to the extreme right/hot posi-

tion and the fan speed control to the high-

est speed.

• If warm air to the floor is desired while

defrosting or defogging, set the mode to

the floor-defrost position.

• Before driving, clear all snow and ice from

the windshield, rear window, outside rear

view mirrors, and all side windows.

2. Select desired temperature.

3. Select the

or

position.

4. The outside (fresh) air and air condi-

tioning will be selected automatically.

If the air-conditioning and outside (fresh)

air position are not selected automatical-

ly, press the corresponding button manu-

ally.

• Clear all snow and ice from the bonnet

and air inlet in the cowl grill to improve

heater and defroster efficiency and to

reduce the probability of fogging up inside

of the windshield.

4 81

Features of your vehicle

Type A

4. The air-conditioning will be turned on

according to the detected ambient

temperature, outside (fresh) air posi-

tion and higher fan speed will be

selected automatically.

If the air-conditioning, outside (fresh) air

position and higher fan speed are not

selected automatically, adjust the corre-

sponding button or knob manually.

If the

position is selected, lower fan

speed is controlled to higher fan speed.

OFD047117

Type B

OFD040116

D250102AFD

To defrost outside windshield

1. Set the fan speed to the highest

(extreme right) position.

2. Set the temperature to the extreme hot

position.

3. Select the

position.

4. The outside (fresh) air and air condi-

tioning will be selected automatically.

OFD047119

Automatic climate control system

D250201AFD

To defog inside windshield

1. Select desired fan speed.

2. Select desired temperature.

3. Press the defrost button (

).

4 82

Features of your vehicle

D250300AUN

Type A

4. The air-conditioning will be turned on

according to the detected ambient

temperature and outside (fresh) air

position will be selected automatically.

Defogging logic

To reduce the possibility of fogging up

the inside of the windshield, the air intake

or air conditioning are controlled auto-

matically according to certain conditions

If the

position is selected, lower fan

speed is controlled to higher fan speed.

such as

or

position.To cancel or

return the defogging logic, do the follow-

ings.

OFD047118

Type B

OFD047120

D250202AFD

To defrost outside windshield

1. Set fan speed to the highest position.

2. Set temperature to the extreme hot

(HI) position.

3. Press the defrost button (

).

4 83

Features of your vehicle

Type A

The A/C display blinks 3 times with 0.5

second of interval. It indicates that the

defogging logic is canceled or returned to

the programmed status.

If the battery has been discharged or dis-

connected, it is reset to the defog logic

status.

OFD047122

Type B

OFD040121

D250301AFD

Manual climate control system

1. Turn the ignition switch to the ON posi-

tion.

2. Turn the mode selection knob to the

defrost position (

).

3. Push the air intake control button

(

) at least 5 times within 3 sec-

onds.

OFD047123

The indicator light in the air intake control

button will blink 3 times with 0.5 second

of interval. It indicates that the defogging

logic is canceled or returned to the pro-

grammed status.

D250302AUN

Automatic climate control system

1. Turn the ignition switch to the ON posi-

tion.

2. Select the defrost position pressing

defrost button (

3. While holding the air conditioning but-

ton (A/C) pressed, press the air intake

).

If the battery has been discharged or dis-

connected, it is reset to the defog logic

status.

control button (

) at least 5 times

within 3 seconds.

4 84

Features of your vehicle

STORAGE COMPARTMENT

D270000AUN

These compartments can be used to

store small items required by the driver

or passengers.

CAUTION

• To avoid possible theft, do not

leave valuables in the storage

compartment.

• Always keep the storage com-

partment covers closed while

driving. Do not attempt to place

so many items in the storage

compartment that the storage

compartment cover can not close

securely.

OFD047207R

OFD047208R

D270100AFD-EA

D270200AFD

Centre console storage

(if equipped)

Glove box

The glove box can be locked and

unlocked with a master key.

To open the glove box, pull the handle

and the glove box will automatically

open. Close the glove box after use.

These compartments can be used to

store small items required by the driver

or front passenger.

To open the centre console storage, pull

up the lever.

WARNING - Flammable

materials

Do not store cigarette lighters,

propane cylinders, or other flamma-

ble/explosive materials in the vehi-

cle. These items may catch fire

and/or explode if the vehicle is

exposed to hot temperatures for

extended periods.

WARNING

To reduce the risk of injury in an

accident or sudden stop, always

keep the glove box door closed

while driving.

4 85

Features of your vehicle

4. Set the temperature control to warm or

cool.

When the cool box is not used, turn the

lever to its closed position.

✽

NOTICE

While using the cooling function, a small

amount of condensed moisture could

damage your pieces of paper.

OFD047209R

OFD047210

D270300AUN

Glove box cooling (if equipped)

Sunglass holder

You can keep beverage cans or other

items warm or cool using the open/close

lever of the vent installed in the glove

box.

To open the sunglass holder, press the

cover and the holder will slowly open.

Place your sunglasses in the compart-

ment door with the lenses facing out.

Push to close.

1. Turn on the fan control switch.

2. Set the air flow control to the face

(

) mode.

3. Turn the open/close lever of the vent

installed in the glove box to the open

position.

(1) OPEN

(2) CLOSE

4 86

Features of your vehicle

(if equipped)

WARNING

• Do not keep objects except sun-

glass inside the sunglass holder.

Such objects can be thrown from

the holder in the event of a sud-

den stop or an accident, possibly

injuring the passengers in the

vehicle.

• Do not open the sunglass holder

while the vehicle is moving. The

rear view mirror of the vehicle

can be blocked by an open sun-

glass holder.

OFD047211

OFD047227

D270500AFD

Luggage box (if equipped)

You can place a first aid kit, a reflector tri-

angle, tools, etc. in the box for easy

access.

1. Grasp the handle on the top of the

cover and lift it.

OFD047212R

D270400AFD

Multi box

To open the cover, pull the lever or push

the button. It can be used for storing

small items.

4 87

Features of your vehicle

OFD047228

D270501AFD

Luggage side tray

To open the cover, pull up the handle and

lift the cover (if equipped). It can be used

for storing small items.

4 88

Features of your vehicle

INTERIOR FEATURES

WARNING

• Do not hold the lighter in after it

is already heated because it will

overheat.

• If the lighter does not pop out

within 30 seconds, remove it to

prevent overheating.

CAUTION

OFD047200R

OFD047201R

Only a genuine HYUNDAI lighter

should be used in the cigarette

lighter socket. The use of plug-in

accessories (shavers, hand-held

vacuums, and coffee pots, for

example) may damage the socket or

cause electrical failure.

D280100AFD

D280200AFD

Cigarette lighter

Ashtray

For the cigarette lighter to work, the igni-

tion switch must be in the ACC position

or the ON position.

To use the cigarette lighter, push it all the

way into its socket. When the element

has heated, the lighter will pop out to the

"ready" position.

Do not hold the cigarette lighter pressed

in. This can damage the heating element

and create a fire hazard.

If it is necessary to replace the cigarette

lighter, use only a genuine HYUNDAI

replacement or its approved equivalent.

WARNING - Ashtray use

• Do not use the vehicle’s ashtrays

as waste receptacles.

• Putting lit cigarettes or matches

in an ashtray with other com-

bustible materials may cause a

fire.

The front ashtray may be opened by

pulling the ashtray lid. To clean the ash-

tray, the plastic receptacle should be

removed by lifting the plastic ash recep-

tacle upward and pulling it out.

4 89

Features of your vehicle

D280300AUN

Front

Cup holder

WARNING - Hot liquids

• Do not place uncovered cups of

hot liquid in the cup holder while

the vehicle is in motion. If the hot

liquid spills, you burn yourself.

Such a burn to the driver could

lead to loss of control of the vehi-

cle.

• To reduce the risk of personal

injury in the event of sudden stop

or collision, do not place uncov-

ered or unsecured bottles, glass-

es, cans, etc., in the cup holder

while the vehicle is in motion.

OFD047202R

Rear (if equipped)

OFD047204R

D280400AFD

Sunvisor

Use the sunvisor to shield direct light

through the front or side windows.

To use a sunvisor, pull it downward.

To use a sunvisor for a side window, pull

it downward, unsnap it from the bracket

(1) and swing it to the side (2).

OFD047203

To use the vanity mirror, pull down the

visor and pull up the mirror cover (3).

D280301AFD

Front

Cups or small beverage cans may be

placed in the cup holders.

Rear (if equipped)

Cups may be placed in the cup holders.

4 90

Features of your vehicle

CAUTION - Vanity mirror

lamp (if equipped)

CAUTION

• Use power outlet only when the

engine is running and remove the

accessory plug after use. Using

the accessory plug for prolonged

periods of time with the engine

off could cause the battery to dis-

charge.

Close the vanity mirror cover

securely and return the sunvisor to

its original position after use. If the

vanity mirror is not closed securely,

the lamp will stay on and could

result in battery discharge.

• Only use 12V electric accessories

which are less than 10A in elec-

tric capacity.

OFD047205R

Wagon (if equipped)

• Adjust the air-conditioner or

heater to the lowest operating

level when using the power outlet.

• Close the cover when not in use.

• Some electronic devices can

cause electronic interference

when plugged into a vehicle’s

power outlet. These devices may

cause excessive audio static and

malfunctions in other electronic

systems or devices used in your

vehicle.

OFD047229

D280500AUN

Power outlet

The power outlet is designed to provide

power for mobile telephones or other

devices designed to operate with vehicle

electrical systems. The devices should

draw less than 10 amps with the engine

running.

4 91

Features of your vehicle

D280601AUN

D280604AUN

• HOUR:

• Display conversion:

Pressing the “H” button (2) with your

finger, a pencil or similar object will

advance the time displayed by one

hour.

To change the 12 hour format to the 24

hour format, press the “R” button (1) for

more than 4 seconds.

For example, if the “R” button is

pressed for more than 4 seconds while

the time is 10:15 p.m., the display will

be changed to 22:15.

D280602AUN

• MINUTE:

Pressing the “M” button (3) with your

finger, a pencil or similar object will

advance the time displayed by one

minute.

OFD047217

D280600AUN

Digital clock (if equipped)

D280603AUN

• RESET:

To clear away minutes, press the “R”

button (1) with your finger, a pencil or

similar object. Then the clock will be

set precisely on the hour.

For example, if the “R” button is

pressed while the time is between 9:01

and 9:29, the display will be reset to

9:00.

WARNING

Do not adjust the clock while driv-

ing. You may lose your steering

control and cause severe personal

injury or accidents.

Whenever the battery terminals or relat-

ed fuses are disconnected, you must

reset the time.

When the ignition switch is in the ACC or

ON position, the clock buttons operate as

follows:

9:01 ~ 9:29 display changed to 9:00

9:30 ~ 9:59 display changed to 10:00

4 92

Features of your vehicle

OFD047215R

OFD047230

OUN026348

D281400BFD

D280700AFD

D280800AUN

Shopping bag holder (if equipped)

Aux, USB and iPod

(if equipped)

Clothes hanger

To use the hanger, pull down the upper

portion of hanger.

If your vehicle has an aux and/or

USB(universal serial bus) port or iPod

port, you can use an aux port to connect

audio devices and an USB port to plug in

an USB and also an iPod port to plug in

an iPod.

CAUTION

Do not hang a bag weighing more

than 3 kg (7 lbs.). It may cause dam-

age to the shopping bag holder.

CAUTION

Do not hang heavy clothes, since

those may damage the hook.

✽

NOTICE

When using a portable audio device

connected to the power outlet, noise may

occur during playback. If this happens,

use the power source of the portable

audio device.

❈ iPod is a trademark of Apple Inc.

4 93

Features of your vehicle

Type A

Type B

Type A

WARNING

The following must be observed

when installing ANY floor mat to

the vehicle.

• Ensure that the floor mats are

securely attached to the vehicle’s

floor mat anchor(s) before driving

the vehicle.

• Do not use ANY floor mat that

cannot be firmly attached to the

vehicle’s floor mat anchors.

OFD047213

OXM049228

Type C

Type B

• Do not stack floor mats on top of

one another (e.g. all-weather rub-

ber mat on top of a carpeted floor

mat). Only a single floor mat

should be installed in each posi-

tion.

IMPORTANT – Your vehicle was

manufactured with driver’s side

floor mat anchors that are

designed to securely hold the

floor mat in place. To avoid any

interference with pedal operation,

HYUNDAI recommends that only

the HYUNDAI floor mat designed

for use in your vehicle be

installed.

OFD047219

OCM039200N

D281000AFD-EA

B571A03Y-AAT

Luggage net (holder)

(if equipped)

Floor mat anchor(s) (if equipped)

When using a floor mat on the front floor

carpet, make sure it attaches to the floor

mat anchor(s) in your vehicle. This keeps

the floor mat from sliding forward.

To keep items from shifting in the cargo

area, you can use the four holders locat-

ed in the cargo area to attach the lug-

gage net.

If necessary, contact your authorised

HYUNDAI dealer to obtain a luggage net.

4 94

Features of your vehicle

For the full size spare tyre equipped vehi-

cle : type A and type B available

For the compact spare tyre equipped

vehicle : type B available

CAUTION

To prevent damage to the goods or

the vehicle, care should be taken

when carrying fragile or bulky

objects in the luggage compart-

ment.

OFD039204

OED037107

To install the barrier net

1. Open the cover for the holder position

(1) or (2) you want to install.

2. Insert the net upper shaft into the large

hole (3) and then secure by sliding into

the small hole (4).

Barrier net (if equipped)

Your vehicle is equipped with a barrier

net.

When you load some cargoes on the rear

seat or rear cargo area, you must install

the barrier net behind front seatback or

rear seatback.

It is designed to help protect the heads of

the occupants by obstructing objects fly-

ing forward in frontal collisions.

WARNING

Avoid eye injury. DO NOT over-

stretch the luggage net. ALWAYS

keep your face and body out of the

luggage net’s recoil path. DO NOT

use when the strap has visible

signs of wear or damage.

There are eight hook holders on both

side of the headliner over the headrests

for upper side fixation and on the floor

behind the front seats or rear seats for

lower side fixation.

4 95

Features of your vehicle

WARNING

• Do not put passengers in the rear

seat or cargo area behind the bar-

rier net.

• Do not put passenger in the rear

centre seat when the barrier net

is installed behind the rear seats.

The barrier net may interfere with

use of the rear centre safety belt.

• Do not load cargo in the area

higher than the barrier net's

upper end.

• Do not load heavy cargo in the

area higher than the seatback to

avoid accident even if the barrier

net is installed.

• Do not load cargo which has

sharp edge that can pass through

the barrier net.

• Do not apply excessive force to

the barrier net by hanging on to

the net or by suspending heavy

cargo and so on.

OFD039205

OED037110

4. Fasten the straps, by using the

adjuster (1).

WARNING

• Make sure that there is no slack

in the barrier net by fastening the

strap securely when installing the

net. The strap should be fastened

after confirming that the hook is

inserted into the upper hook

holder securely.

OED037109

• Make sure that the seatbacks are

locked securely.

3. Hang the net strap hooks in the corre-

sponding hook holders on the floor

behind the front seat or rear seat.

4 96

Features of your vehicle

To remove the barrier net

1. Loosen the straps by using the strap

adjusters and remove the strap hooks

from the hook holders.

2. Remove the net upper shaft by pulling

it through the large holes.

3. Remove the barrier net.

OFD047231

OFD047232

D281100AFD

• To use the cargo security screen, pull

the handle backward and insert the

edges into the slots.

Cargo security screen

(if equipped)

Use the cargo security screen to hide

items stored in the cargo area.

4 97

Features of your vehicle

WARNING

• Do not place objects on the cargo

security screen. Such objects

may be thrown about inside the

vehicle and possibly injure vehi-

cle occupants during an accident

or when braking.

• Never allow anyone to ride in the

luggage compartment. It is

designed for luggage only.

• Maintain the balance of the vehi-

cle and locate the weight as far

forward as possible.

OFD047233

When not in use, place the cargo securi-

ty screen on the lower portion of the

cargo area.

CAUTION

Since the cargo security screen

may be damaged or malformed, do

not put the luggage on it when it is

used.

4 98

Features of your vehicle

EXTERIOR FEATURES

OED046090

OED046091

OED037106

D290300AFD

2. Rotate the cover half way and insert

the cover on the roof hole as the illus-

tration.

D290100AFD-EA

Mounting bracket for roof carrier

(if equipped)

To install or remove a roof carrier, you

can use the mounting bracket and cover

on the roof.

Roof rack (if equipped)

If the vehicle has a roof rack, you can

load cargo on top of your vehicle.

✽

NOTICE

To prevent loosing the roof carrier

cover, install the cover on the roof before

you install the roof carrier.

When you install a roof carrier, use the

following procedure.

1. Insert a slim tool(coin or flat blade driv-

er) into the slot and slide the cover

toward the arrow on the cover.

3. After using the roof carrier, install the

cover back on the roof in the reverse

order.

WARNING

Use a coin or flat blade driver when

you remove the roof carrier cover.

If you use your fingernail, it may

damage your fingernail.

4 99

Features of your vehicle

✽

NOTICE

(Continued)

WARNING

If the vehicle is equipped with a sunroof,

be sure not to position cargo onto the

roof rack in such a way that it could

interfere with sunroof operation.

• Always drive slowly and turn cor-

ners carefully when carrying

items on the roof rack. Severe

wind updrafts, caused by passing

vehicles or natural causes, can

cause sudden upward pressure

on items loaded on the roof rack.

This is especially true when car-

rying large, flat items such as

wood panels or mattresses. This

could cause the items to fall off

the roof rack and cause damage

to your vehicle or others around

you.

• The following specification is the

maximum weight that can be

loaded onto the roof rack.

Distribute the load as evenly as

possible onto the roof rack and

secure the load firmly.

CAUTION

• When carrying cargo on the roof

rack, take the necessary precau-

tions to make sure the cargo does

not damage the roof of the vehicle.

• When carrying large objects on

the roof rack, make sure they do

not exceed the overall roof length

or width.

ROOF

RACK

75 kg (165 lbs.)

EVENLY DISTRIBUTED

Loading cargo or luggage in

excess of the specified weight

limit on the roof rack may dam-

age your vehicle.

• The vehicle centre of gravity will

be higher when items are loaded

onto the roof rack. Avoid sudden

starts, braking, sharp turns,

abrupt manoeuvres or high

speeds that may result in loss of

vehicle control or rollover result-

ing in an accident.

• To prevent damage or loss of

cargo while driving, check fre-

quently before or while driving to

make sure the items on the roof

rack are securely fastened.

(Continued)

4 100

Features of your vehicle

AUDIO SYSTEM

Type A

✽

NOTICE

CAUTION

If you install an aftermarket HID head

lamp, your vehicle’s audio and electron-

ic device may malfunction.

• Before entering a place with a low

height clearance or a car wash,

remove surely the antenna by

rotating it counter-clockwise. If

not, the antenna may be dam-

aged.

• When reinstalling your antenna, it

is important that it is fully tight-

ened to ensure proper reception.

The antenna may be removed

when parking the vehicle or when

loading cargo on the roof rack.

OED036069

Type B

• When cargo is loaded on the roof

rack, do not place the cargo near

the antenna pole to ensure proper

reception.

OFD047224

Antenna

D300102AFD-EA

Roof antenna

Your car uses a roof antenna to receive

both AM and FM broadcast signals. This

antenna is a removable type. To remove

the antenna, turn it counterclockwise. To

install the antenna, turn it clockwise.

4 101

Features of your vehicle

If the SEEK button is pressed for less

than 0.8 second, it will work as follows in

each mode.

VOL (▲/▼) (1)

• Press the up button (▲) to increase

volume.

• Press the down button (▼) to decease

volume.

RADIO mode

It will function as the PRESET STATION

select buttons.

MODE (2)

Press the button to select Radio, Tape (if

equipped) or CD (compact disc).

CDP mode

It will function as the TRACK UP/DOWN

button.

SEEK (▲/▼) (3)

OFD047214

If the SEEK button is pressed for 0.8 sec-

ond or more, it will work as follows in

each mode.

CDC mode

D300200AFD

It will function as the TRACK UP/DOWN

button.

Audio remote control

(if equipped)

The steering wheel audio remote control

button is installed to promote safe driv-

ing.

RADIO mode

It will function as the AUTO SEEK select

button.

Detailed information for audio control

buttons is described in the following

pages in this section.

CDP mode

CAUTION

Do not operate audio remote con-

trol buttons simultaneously.

It will function as the FF/REW button.

CDC mode

It will function as the DISC UP/DOWN

button.

4 102

Features of your vehicle

FM reception

AM reception

FM radio station

JBM001

JBM002

JBM003

D300800AFD-EA

AM broadcasts can be received at

greater distances than FM broadcasts.

This is because AM radio waves are

transmitted at low frequencies. These

long, low frequency radio waves can fol-

low the curvature of the earth rather than

travelling straight out into the atmos-

phere. In addition, they curve around

obstructions so that they can provide bet-

ter signal coverage.

FM broadcasts are transmitted at high

frequencies and do not bend to follow the

earth's surface. Because of this, FM

broadcasts generally begin to fade at

short distances from the station. Also,

FM signals are easily affected by build-

ings, mountains, or other obstructions.

These can result in certain listening con-

ditions which might lead you to believe a

problem exists with your radio. The fol-

lowing conditions are normal and do not

indicate radio trouble:

How car audio works

AM and FM radio signals are broadcast

from transmitter towers located around

your city. They are intercepted by the

radio antenna on your car. This signal is

then received by the radio and sent to

your car speakers.

When a strong radio signal has reached

your vehicle, the precise engineering of

your audio system ensures the best pos-

sible quality reproduction. However, in

some cases the signal coming to your

vehicle may not be strong and clear. This

can be due to factors such as the dis-

tance from the radio station, closeness of

other strong radio stations or the pres-

ence of buildings, bridges or other large

obstructions in the area.

4 103

Features of your vehicle

Using a mobile phone or a two-

way radio

When a mobile phone is used inside the

vehicle, noise may be produced from the

audio equipment. This does not mean

that something is wrong with the audio

equipment. In such a case, use the

mobile phone at a place as far as possi-

ble from the audio equipment.

CAUTION

JBM004

JBM005

When using a communication sys-

tem such a mobile phone or a radio

set inside the vehicle, a separate

external antenna must be fitted.

When a mobile phone or a radio set

is used with an internal antenna

alone, it may interfere with the vehi-

cle's electrical system and adverse-

ly affect safe operation of the vehi-

cle.

• Fading - As your car moves away from

the radio station, the signal will weaken

and sound will begin to fade. When this

occurs, we suggest that you select

another stronger station.

• Flutter/Static - Weak FM signals or

large obstructions between the trans-

mitter and your radio can disturb the

signal causing static or fluttering nois-

es to occur. Reducing the treble level

may lessen this effect until the distur-

bance clears.

• Station Swapping - As a FM signal

weakens, another more powerful sig-

nal near the same frequency may

begin to play. This is because your

radio is designed to lock onto the clear-

est signal. If this occurs, select anoth-

er station with a stronger signal.

• Multi-Path Cancellation - Radio signals

being received from several directions

can cause distortion or fluttering. This

can be caused by a direct and reflect-

ed signal from the same station, or by

signals from two stations with close

frequencies. If this occurs, select

another station until the condition has

passed.

WARNING

Don't use a mobile phone when you

are driving.You must stop at a safe

place to use a mobile phone.

4 104

Features of your vehicle

• Depending on the type of CD-R/CD-

RW CDs, certain CDs may not operate

normally according to manufacturing

companies or making and recording

methods. In such circumstances, if you

still continue to use those CDs, they

may cause the malfunction of your car

audio system.

Care of cassette tapes

(if equipped)

Care of disc (if equipped)

• If the temperature inside the car is too

high, open the car windows for ventilation

before using your car audio.

• It is illegal to copy and use

MP3/WMA/AAC/WAVE files without

permission. Use CDs that are created

only by lawful means.

• Because the thickness of a cassette

tape with the total playback time of

over 60 minutes (C-60) are too thin, we

suggest that you do not use any of

them to avoid having tapes being tan-

gled.

• To achieve better sound quality, period-

ically clean the tape head using a cot-

ton stick with colourless alcohol (once

per month).

• Do not apply volatile agents such as

benzene and thinner, normal cleaners

and magnetic sprays made for ana-

logue disc onto CDs.

✽

NOTICE - Playing an

Incompatible Copy-Protected

Audio CD

Some copy protected CDs, which do not

comply with the international audio CD

standards (Red Book), may not play on

your car audio. Please note that if you

try to play copy protected CDs and the

CD player does not perform correctly

the CDs maybe defective, not the CD

player.

• If a tape is too loose, fasten it to reel by

winding with objects like a pencil.

• Because dust or foreign objects on a

cassette tape may damage the play-

back head, always store tapes in their

cases when not in use.

• Make sure cassette tapes are kept

away from magnetic devices (TV,

stereo system, etc) in order to achieve

better sound quality.

• To prevent the disc surface from get-

ting damaged. Hold and carry CDs by

the edges or the edges of the centre

hole only.

• Clean the disc surface with a piece of

soft cloth before playback (wipe it from

the centre to the outside edge).

• Do not damage the disc surface or

attach pieces of sticky tape or paper

onto it.

• Make sure on undesirable matter other

than CDs are inserted into the CD

player (Do not insert more than one

CD at a time).

•

Be certain that no objects or substances

other than cassette tapes are inserted

into the cassette tape player.

• Because tape media can be distorted

when exposed to direct sunlight, do not

leave cassette tapes on the seats,

dashboard or near the back wind-

shield.

• Keep CDs in their cases after use to

protect them from scratches or dirt.

4 105

Features of your vehicle

RADIO, VOLUME CONTROL (SA710) (IF EQUIPPED)

1. FM/AM Selection Button

2. Power ON/OFF & VOLUME Control

Button

3. AUTO STORE Button

4. Automatic Channel Selection Button

5. TUNE/AUDIO Control Button

6. Preset Button

7. CD/AUX Selection Button

A-100FD

4 106

Features of your vehicle

Type B

1. FM/AM Selection Button

4. Automatic Channel Selection

Button

Turns to AUDIO CONTROL mode, and

toggles in the order of BASS➟MIDDLE➟

TREBLE➟FADER➟BALANCE➟AVC➟

P.BASS➟BASS··· when the button is

pressed each time.

Turns to FM/AM mode and toggles FM1

and FM2➟AM➟FM1··· when the button is

pressed each time.

• When the [SEEK

] button is pressed,

it reduces the band frequency by 5kHz

to automatically select channel. Stops

at the previous frequency if no channel

is found.

2. Power ON/OFF & Volume

Control Button

Turns on/off the set when the IGNITION

SWITCH is on ACC or ON.

If the button is turned to the right, it

increases the volume and left, decreases

the volume.

• When the [SEEK

] button is pressed,

6. Preset Button

Push [1]~[6]button less than 0.8 second

to play the channel saved in each button.

Push preset button for 0.8 second or

longer to save current channel to the

respective button with a beep.

it increases the band frequency by

5kHz to automatically select channel.

Stops at the previous frequency if no

channel is found.

5. TUNE/AUDIO Control Button

3. AUTO STORE Button

Turn this button clockwise by one notch

to increase frequency by 0.05MHz from

current frequency.

Turn this button counterclockwise by one

notch to decrease frequency by 0.05MHz

from current frequency.

7. CD/AUX Selection Button

When the button is pressed, it automati-

cally selects and saves channels with

high reception rate to PRESET but-

tons(1~6) and plays the channel saved in

PRESET1.

If no channel is saved after AST, it will

play the previous channel.

If there is a CD in the CDP DECK it turns

to CD mode, and if a device is connected

to AUX then it toggles.

CD➟AUX➟CD··· when the button is

pressed each time.(It will not turn to AUX

if the auxiliary device is not connected.)

Type A

Turns to AUDIO CONTROL mode, and

toggles in the order of BASS➟MIDDLE

➟TREBLE➟FADER➟BALANCE➟AVC

ON➟···BASS··· when the button is

pressed each time.

4 107

Features of your vehicle

CD (SA710) (IF EQUIPPED)

1. CD loading slot

2. CD Eject Button

3. AUX Selection Button

4. SCAN Play Button

5. Automatic Track Selection Button

6. CD Indicator

7. REPEAT Button

8. RANDOM Play Button

A-100FD

4 108

Features of your vehicle

1. CD loading slot

4. SCAN Play Button

6. CD Indicator

Please face printed side upward and

gently push in.

When the ignition switch is on ACC or

ON and power is OFF, power is automat-

ically turned on if the CD is loaded.

Play first 10 seconds of each song in the

DISC.

To cancel the mode, press the key once

again.

When car ignition switch is ACC or ON

and if the CD is loaded, this indicator is

lighted.

If the CD is ejected the light is turned off.

This CDP supports both 8cm and 12cm

CDs. But if VCD, Data CD, MP3 CD are

loaded, "Disc-Err" message will appear

and CD will be ejected.

5. Automatic Track Selection

Button

7. REPEAT Button

Repeats current song when the button is

pressed for less than 0.8 second.

Repeats the entire DISC when the button

is pressed for 0.8 second or longer.

• Push [SEEK

] button for less than

0.8 second to play from the beginning

of current song.

2. CD Eject Button

• Push [SEEK

] button for less than

Push

button to eject the CD during

0.8 second and press again within 1

second to play the previous song.

8. RANDOM Play Button

CD playback.

This button is enabled when ignition

switch is off.

Turns ON/OFF the randomization of the

play list of files in the currently played

DISC.

To cancel the mode, press the key once

again.

• Push [SEEK

] button for 0.8 second

or longer to initiate reverse direction

high speed sound search of current

song.

3. AUX Selection Button

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

• Push [SEEK

0.8 second to play the next song.

• Push [SEEK ] button for less than

] button for less than

If no Disc and auxiliary device is con-

nected, it displays "NO Media" for 5 sec-

onds and returns to the previous mode.

0.8 second or longer to initiate high

speed sound search of current song.

4 109

Features of your vehicle

RADIO, SET UP, VOLUME CONTROL (PA710) (IF EQUIPPED)

1. FM Selection Button

2. AM Selection Button

3. CD Selection Button

4. AUX Selection Button

5. Automatic Channel Selection Button

6. Power ON/OFF & VOLUME Control Button

7. AUTO STORE Button

8. Screen ON/ OFF Button

9. Information Display Button

10. SET UP Button

11. TUNE/ENTER Button

12. Preset Button

A-200FDD

4 110

Features of your vehicle

1. FM Selection Button

5. Automatic Channel Selection

Button

7. AUTO STORE Button

Turns to FM mode and toggles FM1 and

FM2 when the button is pressed each

time.

When the button is pressed, it automati-

cally selects and saves channels with

high reception rate to PRESET buttons

(1~6) and plays the channel saved in

PRESET1.

If no channel is saved after AST, it will

play the previous channel.

• When the [SEEK

]button is pressed,

it reduces the band frequency by

100khz to automatically select chan-

nel. Stops at the previous frequency if

no channel is found.

2. AM Selection Button

Turns to AM mode, and toggles in the

order of AM1➟AM2➟AM1··· when the

button is pressed each time.

• When the [SEEK

]button is pressed,

it increases the band frequency by

100khz to automatically select channel.

Stops at the previous frequency if no

channel is found.

8. Screen ON/ OFF Button

Turns off/on the displayed data and light

on LCD.

The screen and light will be turned on by

pressing any button except DARK button

when the screen is turned off.

3. CD Selection Button

If there is a cd in the CDP DECK it plays

the CD.

Press CD button to automatically insert

CD when the disc is ejected from the

deck by pressing CD EJECT.

6. Power ON/OFF & Volume

Control Button

• Turns on/off the set when the IGNI-

TION SWITCH is on ACC or ON. If the

button is turned to the right, it increas-

es the volume and left, decreases the

volume.

• In AUX mode, the volume and tone

(BASS, MID, TRE) are adjusted in a

separate way.

If you pull out AUX from a jack and

insert it again, then only volume goes

back to step 10.

9. Information Display Button

Type A

Displays the information of the channel

currently played by RDS.

4. AUX Selection Button

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

If no Disc and auxiliary device is connected,

it displays “NO Media” for 5 seconds and

returns to the previous mode.

Type B

Displays the information of the channel

currently played.

4 111

Features of your vehicle

10. SET UP Button

11. TUNE/ENTER Button

Press this button to turn to the SOUND,

clock setting, time display, SCROLL,

SDVC, temperature display and adjust-

ment mode.

If no action is taken for 5 seconds after

pressing the button, it will return to the

play mode.(After entering SET UP mode,

move between items using the left, right

and PUSH functions of the TUNE button.)

Turn this button clockwise by one notch

to increase frequency by 0.05Mhz from

current frequency.

Turn this button counterclockwise by one

notch to decrease frequency by 0.05Mhz

from current frequency.

Press this button while holding SET UP

button to activate / inactivate the item to.

Select SET UP item using left and right

function of the Tune button.

Type A

The set up item changes from SOUND

➟CLOCK➟TIME➟SCROLL➟SDVC➟TE

MP➟SOUND...

12. Preset Button

Push [1]~[6] buttons less than 0.8 second

to play the channel saved in each button.

Push preset button for 0.8 second or

longer to save current channel to the

respective button with a beep.

Type B

The set up item changes from AUDIO➟

CLOCK➟TIME➟SCROLL➟SDVC➟TEMP

➟P.BASS➟AUDIO

4 112

Features of your vehicle

CD (PA710) (IF EQUIPPED)

1. CD loading slot

2. CD indicator

3. CD Eject Button

4. AUX Selection Button

5. Automatic Track Selection Button

6. INFO Button

7. TUNE/ENTER Button

8. REPEAT Button

9. RANDOM Play Button

10. SCAN Play Button

11. FOLDER Moving Button

A-200FDD

4 113

Features of your vehicle

1. CD loading slot

5. Automatic Track Selection

Button

7. TUNE/ENTER Button

Turn this button clockwise to display

songs after current song.

Also, turn this button counterclockwise to

display songs before current song.

To listen to the displayed song, press the

button to skip to the song and play.

Please face printed side upward and

gently push in. When the ignition switch

is on ACC or ON and power is off, power

is automatically turned on if the CD is

loaded.This CDP supports both 8cm and

12 cm CDs. But if VCD, Data CD, MP3

CD are loaded, "Er-6" message will

appear and CD will be ejected.

• Push [SEEK

] button for less than

0.8 second to play from the beginning

of current song.

• Push [SEEK

] button for less than

0.8 second and press again within 1

second to play the previous song.

8. REPEAT Button

Repeats current song when the button is

pressed for less than 0.8 second.

Repeats the entire DISC when the button

is pressed for 0.8 second or longer.

• Push [SEEK

] button for 0.8 second

or longer to initiate reverse direction

high speed sound search of current

song.

2. CD Indicator

When car ignition switch is ACC or ON

and if the CD is loaded, this indicator is

lighted. If the CD is ejected the light is

turned off.

• Push [SEEK

0.8 second to play the next song.

• Push [SEEK ] button for 0.8 second

] button for less than

9. RANDOM Play Button

Turns on/off the randomization of the

play list of files in the currently played

DISC.

To cancel the mode, press the key once

again.

or longer to initiate high speed sound

search of current song.

3. CD eject Button

Push

button to eject the CD during CD

playback. This button is enabled when

ignition switch is off.

6. INFO Button

Displays the information of the current

CD TRACK in the order of DISC

TITLE➟DISC ARTIST➟TRACK TITLE➟

TRACK ARTIST➟TOTAL TRACK➟ Play

Screen➟DISC TITLE➟···.(not displayed if

the information is not available on the

DISC.)

(If MP3 is displayed FILE NAME ➟TITLE

➟ARTIST➟ALBUM➟FOLDER➟TOTAL

FILE➟FILE NAME➟···)

10. SCAN Play Button

Plays first 10 seconds of each song in

the DISC.

To cancel the mode, press the key once

again.

4. AUX Selection Button

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

If no Disc and auxiliary device is connected,

it displays "NO Media" for 5 seconds and

returns to the previous mode.

4 114

Features of your vehicle

11. FOLDER Moving Button

• Moves [FLDR

] button child folder of

the current folder and displays the first

song in the folder. Press TUNE/ENTER

button to move to the folder displayed.

It will play the first song in the folder.

• Moves [FLDR

] button parent folder

and displays the first song in the folder.

Press TUNE/ENTER button to move to

the folder displayed. It will play the first

song in the folder.

4 115

Features of your vehicle

USING USB (PA710) (IF EQUIPPED)

1. AUX Selection Button

2. Track moving Button

3. INFO Selection Button

4. Folder moving Button

5. TUNE/ENTER Button

6. RANDOM Playback Button

7. REPEAT Selection Button

8. SCAN Selection Button

A-200FDD

4 116

Features of your vehicle

In case USB is connected to the multi

media jack inside the console on the left

hand side of the driver’s seat. When USB

is connected, the ‘USB’ icon will be dis-

played on the top right corner of the dis-

play screen.

3. INFO Button

6. RANDOM Playback Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟TITLE➟ARTIST➟ALBUM➟FOLDER➟

TOTAL FILE➟FILE NAME➟… (Displays

no information if the file has no song

information.)

Press the button for less than 0.8 second

to start or stop the random playback of

the songs in the current folder.

Press the button for more than 0.8 sec-

ond to randomly play the entire songs in

the USB device.

1. AUX Selection Button

Press the button again to cancel the mode.

If USB is not connected, it switches to the

USB mode from the Radio and CD mode

to play the song files stored in the USB.

4. Folder moving Button

7. REPEAT Button

Press the button for less than 0.8 second

to repeat the song currently played.

Press the button for more than 0.8 sec-

ond to repeat the entire songs in the USB

device.

• Moves [FLDR

] button child folder of

the current folder and displays the first

song in the folder. Press TUNE/ENTER

button to move to the folder displayed.

It will play the first song in the folder.

If AUX is not connected, it is invalid key.

2. Track Moving Button

• Moves [FLDR

] button parent folder

• Press the [SEEK

] button for less

and displays the first song in the folder.

Press TUNE/ENTER button to move to

the folder displayed. It will play the first

song in the folder.

than 0.8 second to play from the begin-

ning of the song currently played.

Press the button for less than 0.8 sec-

ond and press it again within 1 second

to move to and play the previous track.

8. SCAN Button

Plays 10 seconds of each song in the USB

device.

Press the button once again to cancel

scanning.

Press the button for 0.8 second or 5. TUNE/ENTER Button

longer to play the song in reverse

direction in fast speed.

Turn this button clockwise to display the

songs next to the currently played song.

• Press the [SEEK

than 0.8 second to move to the next

track.

] button for less

Turn the button counterclockwise to dis-

play the songs before the currently

played song.

Press the button to skip to and play the

selected song.

Press the button for 0.8 second or

longer to play the song in forward

direction in fast speed.

4 117

Features of your vehicle

(Continued)

CAUTION IN USING

USB DEVICE

• To use the external USB device,

make sure the device is not

mounted when starting up the

vehicle and mount the device

after starting up.

• If you start the vehicle when the

USB device is mounted, it may

damage the USB device. (USB is

not ESA)

• If the vehicle is started up or

turned off while the external USB

device is connected, the external

USB device may not work.

• It may not play inauthentic MP3 or

WMA files.

1) It can only play MP3 files with

the compression rate between

8Kbps~320Kbps.

2) It can only play WMA music

files with the compression rate

between 8Kbps~320Kbps.

• Take cautions for static electricity

when mounting or dismounting

the external USB device.

• Depending on the condition of

the external USB device, the con-

nected external USB device can

be unrecognizable.

• When the VHAPTTL byte/sector

setting of External USB devices is

not either 512BYTE or 2048BYTE,

then the device will not be recog-

nized.

• Use only the USB device format-

ted to FAT 12/16/32.

• USB device without USB I/F

authentication may not be recog-

nizable.

• Make sure the USB connection

terminal does not come in contact

with human body or any object.

• If you repeat mounting or dis-

mounting USB device in a short

period of time, it may break the

device.

• You might hear strange noise

when mounting or dismounting a

USB device.

• If you dismount the external USB

device during playback in USB

mode, the external USB device can

be damaged or malfunction.

Therefore, mount the external USB

device when the engine is turned

off or in another mode.

• Depending on the type and capac-

ity of the external USB device or

the type of the files stored in the

device, there is a difference in the

time taken for recognition of the

device, but this is not a trouble

and you only have to wait.

• Do not use the USB device for other

purposes than playing music files.

• Use of USB accessories such as

the recharger or heater using

USB I/F may lower the perform-

ance or cause trouble.

• If you use devices such as the

USB hub you purchased sepa-

rately, the vehicle’s audio system

may not recognize the USB

device. Connect the USB device

directly to the multimedia termi-

nal of the vehicle.

(Continued)

• An encoded MP3 player is not

recognizable.

(Continued)

4 118

Features of your vehicle

(Continued)

• If USB device is divided by logical

drives, only the music files on the

highest-priority drive are recog-

nized by car audio.

• Devices such as MP3 Player/

Cellular phone/Digital camera

those are not recognizable by

standard USB I/F can be unrecog-

nizable.

• Please avoid using USB memory

products which can be used as

key chains or cellular phone

accessories as they could cause

damage to the USB jack. Please

make certain only to use plug type

connector products as shown

below.

• USB devices other than standard-

ized goods (METAL COVER TYPE

USB) can be unrecognizable.

• USB flash memory reader (such

as CF, SD, microSD, etc.) or exter-

nal-HDD type devices can be

unrecognizable.

• Music files protected by DRM

(DIGITAL RIGHTS MANAGEMENT)

are not recognizalbe.

• The data in the USB memory may

be lost while using this AUDIO. It

is recommeded to back up impor-

tant data on a personal storage

device.

(Continued)

4 119

Features of your vehicle

RUNNING iPod (PA710) (IF EQUIPPED)

1. iPod Selection Button

2. Track moving Button

3. INFO Selection Button

4. Category Selection Button

5. TUNE/ENTER Button

6. RANDOM Playback Button

7. REPEAT Selection Button

* iPod is a trademark of Apple Inc.

A-200FDD

4 120

Features of your vehicle

In case the iPod exclusive cable is con-

nected to the multimedia jack inside the

console on the left hand side of the dri-

ver’s seat. When the iPod is connected,

the ‘iPod’ icon will be displayed on the top

right corner of the display screen.

If you want to listen to the song displayed

in the song category, press the button,

then it will skip to the selected song and

play.

3. INFO Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟ TITLE➟ ARTIST➟ ALBUM➟ FILE

NAME➟…

(Displays no information if the file has no

song information.)

6. RANDOM Playback Button

Press the button for less than 0.8 second

to activate or deactivate the random play-

back of the songs within the current cat-

egory.

Press the button for longer than 0.8 sec-

ond to randomly play all songs in the

entire album of the iPod.

1. iPod Selection Button

If iPod is connected, it switches to the

iPod mode from the Radio and CD mode

to play the song files stored in the iPod.

If there are no CD and AUX, it displays

'NO MEDIA'.

4. Category Selection Button

Moves to the upper category from cur-

rently played category of the iPod.

You will be able to search through the

lower category of the selected category.

The order of iPod's category is SONG,

ALBUMS, ARTISTS, GENRES, and

iPod. (Refer to the iPod user's manual for

more information)

Press the button once again to cancel the

mode.

2. Track Moving Button

• Press the [SEEK

] button for less

7. REPEAT Button

Repeats the song currently played.

than 0.8 second to play from the begin-

ning of the song currently played.

Press the button for less than 0.8 sec- 5. TUNE/ENTER Button

ond and press it again within 1 second

to move to and play the previous track.

Press the button for 0.8 second or

longer to play the song in reverse

direction in fast speed.

When you turn the button clockwise, it

will display the songs (category) next to

the song currently played (category in

the same level).

Also, when you turn the button counter-

clockwise, it will display the songs (cate-

gory) before the song currently played

(category in the same level).

• Press the [SEEK

] button for less

than 0.8 second to move to the next

track.

Press the button for 0.8 second or

longer to play the song in forward

direction in fast speed.

4 121

Features of your vehicle

✽

NOTICE FOR USING iPod

DEVICE

(Continued)

CAUTION IN USING

iPod DEVICE

• When the iPod cable is connected,

the system can be switched to the

AUX mode even without the iPod

device and can cause noise.

Disconnect iPod cable when you

are not using the iPod device.

• When the iPod is not used for the

audio system, the iPod cable has

to be separate from iPod devices.

Original display of iPod may not be

displayed.

• Some iPod models might not support

the communication protocol and the

files will not be played. (iPod models

supported: Mini, 4G, Photo, Nano,

5G)

• You need the power cable exclu-

sive for iPod (purchased sepa-

rately) in order to operate iPod

with the buttons on the audio sys-

tem. The PC cable provided by

Apple may cause malfunction and

do not use it for vehicle use.

• When connecting the device with

an iPod cable, push in the jack

fully not to interfere with commu-

nication.

• When adjusting the sound effects

of iPod and the audio system, the

sound effects of both devices will

overlap each and might cause

reduce or distort the quality of the

sound.

• The order of search or playback of

songs in the iPod can be different

from the order searched in the audio

system.

• If the iPod crashes due to its own trou-

ble, reset iPod. (Reset: Refer to iPod

manual)

• An iPod may not operate normally on

low battery.

• Deactivate (turn off) the equalizer

function of iPod when adjusting

the audio system’s volume, and

turn off the equalizer of the audio

system when using the equalizer

of iPod.

(Continued)

4 122

Features of your vehicle

RADIO, SET UP, VOLUME CONTROL (PA760) (IF EQUIPPED)

1. FM Selection Button

2. AM Selection Button

3. CD Selection Button

4. AUX Selection Button

5. Automatic Channel Selection Button

6. Power ON/OFF & VOLUME Control

Button

7. AUTO STORE Button

8. Screen ON/ OFF Button

9. Information Display Button

10. SET UP Button

11. TUNE/ENTER Button

12. Preset Button

A-300FDD

4 123

Features of your vehicle

1. FM Selection Button

5. Automatic Channel Selection

Button

7. AUTO STORE Button

Turns to FM mode and toggles FM1 and

FM2 when the button is pressed each

time.

When the button is pressed, it automati-

cally selects and saves channels with

high reception rate to PRESET buttons

(1~6) and plays the channel saved in

PRESET1.

If no channel is saved after AST, it will

play the previous channel.

• When the [SEEK

]button is pressed,

it reduces the band frequency by

100khz to automatically select channel.

Stops at the previous frequency if no

channel is found.

2. AM Selection Button

Turns to AM mode, and toggles in the

order of AM1➟AM2➟AM1··· when the

button is pressed each time.

• When the [SEEK

]button is pressed,

it increases the band frequency by

100khz to automatically select channel.

Stops at the previous frequency if no

channel is found.

8. Screen ON/ OFF Button

Turns off/on the displayed data and light

on LCD.

The screen and light will be turned on by

pressing any button except DARK button

when the screen is turned off.

3. CD Selection Button

If there is a cd in the CDP DECK it plays

the CD.

Press CD button to automatically insert

CD when the disc is ejected from the

deck by pressing CD EJECT.

6. Power ON/OFF & Volume

Control Button

• Turns on/off the set when the IGNI-

TION SWITCH is on ACC or ON. If the

button is turned to the right, it increas-

es the volume and left, decreases the

volume.

• In AUX mode, the volume and tone

(BASS, MID, TRE) are adjusted in a

separate way.

If you pull out AUX from a jack and

insert it again, then only volume goes

back to step 10.

9. Information Display Button

Type A

Displays the information of the channel

currently played by RDS.

4. AUX Selection Button

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

If no Disc and auxiliary device is connected,

it displays “NO Media” for 5 seconds and

returns to the previous mode.

Type B

Displays the information of the channel

currently played.

4 124

Features of your vehicle

10. SET UP Button

11. TUNE/ENTER Button

Press this button to turn to the SOUND,

clock setting, time display, SCROLL,

SDVC, temperature display and adjust-

ment mode.

If no action is taken for 5 seconds after

pressing the button, it will return to the

play mode.(After entering SET UP mode,

move between items using the left, right

and PUSH functions of the TUNE button.)

Turn this button clockwise by one notch

to increase frequency by 0.05Mhz from

current frequency.

Turn this button counterclockwise by one

notch to decrease frequency by 0.05Mhz

from current frequency.

Press this button while holding SET UP

button to activate / inactivate the item to.

Select SET UP item using left and right

function of the Tune button.

Type A

The set up item changes from SOUND

➟CLOCK➟TIME➟SCROLL➟SDVC➟TE

MP➟SOUND...

12. Preset Button

Push [1]~[6] buttons less than 0.8 second

to play the channel saved in each button.

Push preset button for 0.8 second or

longer to save current channel to the

respective button with a beep.

Type B

The set up item changes from AUDIO➟

CLOCK➟TIME➟SCROLL➟SDVC➟TEMP

➟AUDIO...

4 125

Features of your vehicle

CD (PA760) (IF EQUIPPED)

1. CD loading slot

2. CD indicator

3. CD Eject Button

4. LOAD Button

5. AUX Selection Button

6. Automatic Track Selection Button

7. INFO Button

8. TUNE/ENTER Button

9. REPEAT Button

10. RANDOM Play Button

11. DISC selection Button

12. SCAN Play Button

13. FOLDER Moving Button

A-300FDD

4 126

Features of your vehicle

1. CD loading slot

5. AUX Selection Button

7. INFO Button

Please face printed side upward and

gently push in. When the ignition switch

is on ACC or ON and power is off, power

is automatically turned on if the CD is

loaded.This CDP supports both 8cm and

12 cm CDs. But if VCD, Data CD are

loaded, "Er-6" message will appear and

CD will be ejected.

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

If no auxiliary device is connected, it dis-

plays "NO CONNECT" for 3 seconds and

returns to the previous mode.

Displays the information of the current

CD TRACK in the order of DISC

TITLE➟DISC ARTIST➟TRACK TITLE➟

TRACK ARTIST➟TOTAL TRACK➟ Play

Screen➟DISC TITLE➟···.(not displayed if

the information is not available on the

DISC.)

(If MP3 is displayed FILE NAME ➟TITLE

➟ARTIST➟ALBUM➟FOLDER➟TOTAL

FILE➟FILE NAME➟···)

6. Automatic Track Selection

Button

2. CD Indicator

CD is loaded, this slot icon is displayed,

If the CD is ejected the slot icon is display

off.

• Push [SEEK

] button for less than

0.8 second to play from the beginning

of current song.

8. TUNE/ENTER Button

Turn this button clockwise to display

songs after current song.

Also, turn this button counterclockwise to

display songs before current song.

To listen to the displayed song, press the

button to skip to the song and play.

• Push [SEEK

] button for less than

0.8 second and press again within 3

seconds to play the previous song.

3. CD eject Button

• Pressing the button for less than 0.8

second will eject 1 disc while pressing

for 0.8 second ~ 3 seconds will eject all

discs.

• Pressing the button for over 5 seconds

will eject all discs by force. (EMER-

GENCY EJECT)

• Push [SEEK

] button for 0.8 second

or longer to initiate reverse direction

high speed sound search of current

song.

9. REPEAT Button

Repeats current song when the button is

pressed for less than 0.8 second.

Repeats the entire DISC when the button

is pressed for 0.8 second or longer.

• Push [SEEK

0.8 second to play the next song.

• Push [SEEK ] button for 0.8 second

] button for less than

or longer to initiate high speed sound

search of current song.

4. CD LOAD Button

Push [LOAD] button to load CDs to avail-

able CDC deck (from 1~6). Push [LOAD]

button for more than 2 seconds to load

into all available decks.

The last CD will play. 10 seconds idle sta-

tus will disable loading process.

10. RANDOM Play Button

Turns on/off the randomization of the play

list of files in the currently played DISC.

To cancel the mode, press the key once

again.

4 127

Features of your vehicle

11. DISC Selection Button

• [DISC

] Change Button

Changes disc to the previous disc.

• [DISC

] Change Button

Changes disc to the next disc.

12. SCAN Play Button

Plays first 10 seconds of each song in the

DISC.

To cancel the mode, press the key once

again.

13. FOLDER Moving Button

• Moves [FLDR

] button child folder of

the current folder and displays the first

song in the folder. Press TUNE/ENTER

button to move to the folder displayed.

It will play the first song in the folder.

• Moves [FLDR

] button parent folder

and displays the first song in the folder.

Press TUNE/ENTER button to move to

the folder displayed. It will play the first

song in the folder.

4 128

Features of your vehicle

USING USB (PA760) (IF EQUIPPED)

1. AUX Selection Button

2. Track moving Button

3. INFO Selection Button

4. Folder moving Button

5. TUNE/ENTER Button

6. RANDOM Playback Button

7. REPEAT Selection Button

8. SCAN Selection Button

A-300FDD

4 129

Features of your vehicle

In case USB is connected to the multi

media jack inside the console on the left

hand side of the driver’s seat. When USB

is connected, the ‘USB’ icon will be dis-

played on the top right corner of the dis-

play screen.

3. INFO Button

6. RANDOM Playback Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟TITLE➟ARTIST➟ALBUM➟FOLDER➟

TOTAL FILE➟FILE NAME➟… (Displays

no information if the file has no song

information.)

Press the button for less than 0.8 second

to start or stop the random playback of

the songs in the current folder.

Press the button for more than 0.8 sec-

ond to randomly play the entire songs in

the USB device.

1.AUX Selection Button

Press the button again to cancel the mode.

If USB is not connected, it switches to the

USB mode from the Radio and CD mode

to play the song files stored in the USB.

4. Folder moving Button

7. REPEAT Button

Press the button for less than 0.8 second

to repeat the song currently played.

Press the button for more than 0.8 sec-

ond to repeat the entire songs in the USB

device.

• Moves [FLDR

] button child folder of

the current folder and displays the first

song in the folder. Press TUNE/ENTER

button to move to the folder displayed.

It will play the first song in the folder.

If AUX is not connected, it is invalid key.

2. Track Moving Button

• Moves [FLDR

] button parent folder

• Press the [SEEK

] button for less

and displays the first song in the folder.

Press TUNE/ENTER button to move to

the folder displayed. It will play the first

song in the folder.

than 0.8 second to play from the begin-

ning of the song currently played.

Press the button for less than 0.8 sec-

ond and press it again within 1 second

to move to and play the previous track.

8. SCAN Button

Plays 10 seconds of each song in the USB

device.

Press the button once again to cancel

scanning.

Press the button for 0.8 second or 5. TUNE/ENTER Button

longer to play the song in reverse

direction in fast speed.

Turn this button clockwise to display the

songs next to the currently played song.

• Press the [SEEK

than 0.8 second to move to the next

track.

] button for less

Turn the button counterclockwise to dis-

play the songs before the currently

played song.

Press the button to skip to and play the

selected song.

Press the button for 0.8 second or

longer to play the song in forward

direction in fast speed.

4 130

Features of your vehicle

(Continued)

CAUTION IN USING

USB DEVICE

• To use the external USB device,

make sure the device is not

mounted when starting up the

vehicle and mount the device

after starting up.

• If you start the vehicle when the

USB device is mounted, it may

damage the USB device. (USB is

not ESA)

• If the vehicle is started up or

turned off while the external USB

device is connected, the external

USB device may not work.

• It may not play inauthentic MP3 or

WMA files.

1) It can only play MP3 files with

the compression rate between

8Kbps~320Kbps.

2) It can only play WMA music

files with the compression rate

between 8Kbps~320Kbps.

• Take cautions for static electricity

when mounting or dismounting

the external USB device.

• Depending on the condition of

the external USB device, the con-

nected external USB device can

be unrecognizable.

• When the VHAPTTL byte/sector

setting of External USB devices is

not either 512BYTE or 2048BYTE,

then the device will not be recog-

nized.

• Use only the USB device format-

ted to FAT 12/16/32.

• USB device without USB I/F

authentication may not be recog-

nizable.

• Make sure the USB connection

terminal does not come in contact

with human body or any object.

• If you repeat mounting or dis-

mounting USB device in a short

period of time, it may break the

device.

• You might hear strange noise

when mounting or dismounting a

USB device.

• If you dismount the external USB

device during playback in USB

mode, the external USB device can

be damaged or malfunction.

Therefore, mount the external USB

device when the engine is turned

off or in another mode.

• Depending on the type and capac-

ity of the external USB device or

the type of the files stored in the

device, there is a difference in the

time taken for recognition of the

device, but this is not a trouble

and you only have to wait.

• Do not use the USB device for other

purposes than playing music files.

• Use of USB accessories such as

the recharger or heater using

USB I/F may lower the perform-

ance or cause trouble.

• If you use devices such as the

USB hub you purchased sepa-

rately, the vehicle’s audio system

may not recognize the USB

device. Connect the USB device

directly to the multimedia termi-

nal of the vehicle.

(Continued)

• An encoded MP3 player is not

recognizable.

(Continued)

4 131

Features of your vehicle

(Continued)

• If USB device is divided by logical

drives, only the music files on the

highest-priority drive are recog-

nized by car audio.

• Devices such as MP3 Player/

Cellular phone/Digital camera

those are not recognizable by

standard USB I/F can be unrecog-

nizable.

• Please avoid using USB memory

products which can be used as

key chains or cellular phone

accessories as they could cause

damage to the USB jack. Please

make certain only to use plug type

connector products as shown

below.

• USB devices other than standard-

ized goods (METAL COVER TYPE

USB) can be unrecognizable.

• USB flash memory reader (such

as CF, SD, microSD, etc.) or exter-

nal-HDD type devices can be

unrecognizable.

• Music files protected by DRM

(DIGITAL RIGHTS MANAGEMENT)

are not recognizalbe.

• The data in the USB memory may

be lost while using this AUDIO. It

is recommeded to back up impor-

tant data on a personal storage

device.

(Continued)

4 132

Features of your vehicle

RUNNING iPod (PA760) (IF EQUIPPED)

1. iPod Selection Button

2. Track moving Button

3. INFO Selection Button

4. Category Selection Button

5. TUNE/ENTER Button

6. RANDOM Playback Button

7. REPEAT Selection Button

* iPod is a trademark of Apple Inc.

A-300FDD

4 133

Features of your vehicle

In case the iPod exclusive cable is con-

nected to the multimedia jack inside the

console on the left hand side of the dri-

ver’s seat. When the iPod is connected,

the ‘iPod’ icon will be displayed on the top

right corner of the display screen.

If you want to listen to the song displayed

in the song category, press the button,

then it will skip to the selected song and

play.

3. INFO Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟ TITLE➟ ARTIST➟ ALBUM➟ FILE

NAME➟…

(Displays no information if the file has no

song information.)

6. RANDOM Playback Button

Press the button for less than 0.8 second

to activate or deactivate the random play-

back of the songs within the current cat-

egory.

Press the button for longer than 0.8 sec-

ond to randomly play all songs in the

entire album of the iPod.

1. iPod Selection Button

If iPod is connected, it switches to the

iPod mode from the Radio and CD mode

to play the song files stored in the iPod.

If there are no CD and AUX, it displays

'NO MEDIA'.

4. Category Selection Button

Moves to the upper category from cur-

rently played category of the iPod.

You will be able to search through the

lower category of the selected category.

The order of iPod's category is SONG,

ALBUMS, ARTISTS, GENRES, and

iPod. (Refer to the iPod user's manual for

more information)

Press the button once again to cancel the

mode.

2. Track Moving Button

• Press the [SEEK

] button for less

7. REPEAT Button

Repeats the song currently played.

than 0.8 second to play from the begin-

ning of the song currently played.

Press the button for less than 0.8 sec- 5. TUNE/ENTER Button

ond and press it again within 1 second

to move to and play the previous track.

Press the button for 0.8 second or

longer to play the song in reverse

direction in fast speed.

When you turn the button clockwise, it

will display the songs (category) next to

the song currently played (category in

the same level).

Also, when you turn the button counter-

clockwise, it will display the songs (cate-

gory) before the song currently played

(category in the same level).

• Press the [SEEK

] button for less

than 0.8 second to move to the next

track.

Press the button for 0.8 second or

longer to play the song in forward

direction in fast speed.

4 134

Features of your vehicle

✽

NOTICE FOR USING iPod

DEVICE

(Continued)

CAUTION IN USING

iPod DEVICE

• When the iPod cable is connected,

the system can be switched to the

AUX mode even without the iPod

device and can cause noise.

Disconnect iPod cable when you

are not using the iPod device.

• When the iPod is not used for the

audio system, the iPod cable has

to be separate from iPod devices.

Original display of iPod may not be

displayed.

• Some iPod models might not support

the communication protocol and the

files will not be played. (iPod models

supported: Mini, 4G, Photo, Nano,

5G)

• You need the power cable exclu-

sive for iPod (purchased sepa-

rately) in order to operate iPod

with the buttons on the audio sys-

tem. The PC cable provided by

Apple may cause malfunction and

do not use it for vehicle use.

• When connecting the device with

an iPod cable, push in the jack

fully not to interfere with commu-

nication.

• When adjusting the sound effects

of iPod and the audio system, the

sound effects of both devices will

overlap each and might cause

reduce or distort the quality of the

sound.

• The order of search or playback of

songs in the iPod can be different

from the order searched in the audio

system.

• If the iPod crashes due to its own trou-

ble, reset iPod. (Reset: Refer to iPod

manual)

• An iPod may not operate normally on

low battery.

• Deactivate (turn off) the equalizer

function of iPod when adjusting

the audio system’s volume, and

turn off the equalizer of the audio

system when using the equalizer

of iPod.

(Continued)

4 135

Features of your vehicle for Your Hyundai I30 4 Door Third Generation (2016-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals