Get Features of your vehicle Guide for Hyundai Ix35 SUV First Generation (2009-2015)

Keys / 4-3

Remote keyless entry / 4-4

Theft-alarm system / 4-7

Door locks / 4-9

Tailgate / 4-13

Windows / 4-15

Hood / 4-19

Fuel filler door / 4-21

Features of your vehicle

4

Panoramic sunroof / 4-24

Steering wheel / 4-28

Mirrors / 4-30

Instrument cluster / 4-33

Rearview camera / 4-49

Hazard warning flasher / 4-49

Lighting / 4-50

Wipers and washers / 4-54

Interior light / 4-57

Defroster / 4-59

Manual climate control system / 4-61

Automatic climate control system / 4-70

Windshield defrosting and defogging / 4-77

Storage compartment / 4-80

Interior features / 4-82

Exterior features / 4-88

Audio system / 4-89

Features of your vehicle

4

Features of your vehicle

KEYS

WARNING - Ignition key

Leaving children unattended in a

vehicle with the ignition key is dan-

gerous even if the key is not in the

ignition switch. Children copy

adults and they could place the key

in the ignition switch. The ignition

key would enable children to oper-

ate power windows or other con-

trols, or even make the vehicle

move, which could result in serious

bodily injury or even death. Never

leave the keys in your vehicle with

unsupervised children.

OUN046100L

OUN026060

Record your key number

Key operations

Used to start the engine, lock and unlock

the doors.

The key code number is stamped on the

bar code tag attached to the key set.

Should you lose your keys, this number

will enable an authorized HYUNDAI deal-

er to duplicate the keys easily. Remove

the bar code tag and store it in a safe

place. Also, record the code number and

keep it in a safe place (not in the vehicle).

WARNING

Use only HYUNDAI original parts

for the ignition key in your vehicle.

If an aftermarket key is used, the

ignition switch may not return to

ON after START. If this happens, the

starter will continue to operate

causing damage to the starter

motor and possible fire due to

excessive current in the wiring.

4 3

Features of your vehicle

REMOTE KEYLESS ENTRY

Unlock (2)

Alarm (3)

Driver's door is unlocked if the unlock

button is pressed once. The hazard

warning lights will blink twice to indicate

that the driver's door is unlocked.

The horn sounds and hazard warning

lights flash for about 30 seconds if this

button is pressed. To stop the horn and

lights, press any button on the transmit-

ter.

All doors (and tailgate) are unlocked if

the unlock button is pressed once more

within 4 seconds. The hazard warning

lights will blink twice again to indicate

that all doors (and tailgate) are unlocked.

After depressing this button, the doors

(and tailgate) will be locked automatical-

ly unless you open any door within 30

seconds.

OLM049002N

Remote keyless entry system

operations

✽

NOTICE

Lock (1)

All doors (and tailgate) are locked if the

lock button is pressed.

You can change the system to unlock all

doors by one pressing the unlock button

on the transmitter. If you want this fea-

ture (central door unlock mode), per-

form the following:

If all doors (and tailgate) are closed, the

hazard warning lights will blink once to

indicate that all doors (and tailgate) are

locked.

Unlock mode conversion (two stage

unlock mode ↔ central door unlock

mode)

The chime sounds once if the lock button

is pressed once more within 4 seconds.

However, if any door (or tailgate) remains

open, the hazard warning lights and the

chime will not operate. If all doors (and

tailgate) are closed after the lock button

is pressed, the hazard warning lights

blink.

The unlock mode is changed alternately

by pressing the lock button and unlock

button on the transmitter at the same

time for 4 seconds or more. The hazard

warning lights will blink four times to

indicate that the mode conversion is

completed.

4 4

Features of your vehicle

This device complies with Part 15 of

the FCC rules.

Transmitter precautions

CAUTION

✽

NOTICE

The transmitter will not work if any of

following occur:

Keep the transmitter away from

water or any liquid. If the keyless

entry system is inoperative due to

exposure to water or other liquids,

it will not be covered by your manu-

facturer’s vehicle warranty.

Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference, and

• The ignition key is in ignition switch.

• You exceed the operating distance

limit (about 30 feet [10 m]).

• The battery in the transmitter is

weak.

2. This device must accept any interfer-

ence received, including interference

that may cause undesired operation.

• Other vehicles or objects may be

blocking the signal.

WARNING

• The weather is extremely cold.

• The transmitter is close to a radio

transmitter such as a radio station or

an airport which can interfere with

normal operation of the transmitter.

When the transmitter does not work

correctly, open and close the door with

the ignition key. If you have a problem

with the transmitter, contact an author-

ized HYUNDAI dealer.

Changes or modifications not

expressly approved by the party

responsible for compliance could

void the user’s authority to operate

the equipment. If the keyless entry

system is inoperative due to

changes or modifications not

expressly approved by the party

responsible for compliance, it will

not be covered by your manufactur-

er’s vehicle warranty.

4 5

Features of your vehicle

For replacement transmitters, see an

authorized HYUNDAI dealer for transmit-

ter reprogramming.

CAUTION

An inappropriately disposed bat-

tery can be harmful to the environ-

ment and human health.

CAUTION

Dispose the battery according to

your local law(s) or regulation.

• The keyless entry system trans-

mitter is designed to give you

years of trouble-free use, howev-

er it can malfunction if exposed to

moisture or static electricity. If

you are unsure how to use your

transmitter or replace the battery,

contact an authorized HYUNDAI

dealer.

OLM049200

Battery replacement

Transmitter uses a 3 volt lithium battery

which will normally last for several years.

When replacement is necessary, use the

following procedure.

• Using the wrong battery can

cause the transmitter to malfunc-

tion. Be sure to use the correct

battery.

1. Insert a slim tool into the slot and gen-

tly pry open the transmitter center

cover.

• To avoid damaging the transmit-

ter, don't drop it, get it wet, or

expose it to heat or sunlight.

2. Replace the battery with a new battery

(CR2032). When replacing the battery,

make sure the battery positive “+” sym-

bol faces up as indicated in the illus-

tration.

3. Install the battery in the reverse order

of removal.

4 6

Features of your vehicle

THEFT-ALARM SYSTEM

The system can also be armed by lock-

ing the doors with the key from the front

doors; however, the hazard warning

lights will not blink using this method.

Armed stage

Park the car and stop the engine. Arm

the system as described below.

1. Remove the ignition key from the igni-

tion switch and exit the vehicle.

Armed

stage

✽

NOTICE

2. Make sure that all doors (and tailgate)

and engine hood are closed and

latched.

The theft-alarm system by the key can

be deactivated by an authorized

HYUNDAI dealer.

If you want this feature, consult an

authorized HYUNDAI dealer.

Theft-alarm

stage

Disarmed

stage

3. Lock the doors using the transmitter of

the keyless entry system.

After completion of the steps above, the

hazard warning lights will blink once to

indicate that the system is armed.

Do not arm the system until all pas-

sengers have left the vehicle. If the

system is armed while a passenger(s)

remains in the vehicle, the alarm may

be activated when the remaining pas-

senger(s) leave the vehicle. If any

door (or tailgate) or engine hood is

opened within 30 seconds after the

system enters the armed stage, the

system is disarmed to prevent an

unnecessary alarm.

This system is designed to provide pro-

tection from unauthorized entry into the

car. This system is operated in three

stages: the first is the "Armed" stage, the

second is the "Theft-alarm" stage, and

the third is the "Disarmed" stage. If trig-

gered, the system provides an audible

alarm with blinking of the hazard warning

lights.

If any door (or tailgate) or engine hood

remains open, the hazard warning lights

and the chime will not operate and the

theft-alarm will not arm. If all doors (and

tailgate) and engine hood are closed

after the lock button is pressed, the haz-

ard warning lights blink once.

4 7

Features of your vehicle

Theft-alarm stage

Disarmed stage

CAUTION

The alarm will be activated if any of the

following occurs while the system is

armed.

The system will be disarmed when the

doors (and tailgate) are unlocked with the

transmitter or the ignition key.

Do not change, alter or adjust the

theft-alarm system because it could

cause the theft-alarm system to

malfunction. The system should

only be serviced by an authorized

HYUNDAI dealer.

• A front or rear door is opened without

using the ignition key or transmitter.

After depressing the unlock button, the

hazard warning lights will blink twice to

indicate that the system is disarmed.

• The tailgate is opened without using

the transmitter.

• The engine hood is opened.

After depressing the unlock button, if any

door (or tailgate) is not opened within 30

seconds, the system will be rearmed.

Malfunctions caused by improper

alterations, adjustments or modifi-

cations to the theft-alarm system

are not covered by your vehicle

manufacturer warranty.

The horn will sound and the hazard

warning lights will blink continuously for

approximately 27 seconds, and repeat

the horn 2 times unless the system is dis-

armed. To turn off the system, unlock the

doors with the ignition key or transmitter.

✽

NOTICE

• Avoid trying to start the engine while

the alarm is activated. The vehicle

starting motor is disabled during the

theft-alarm stage.

If the system is not disarmed with the

transmitter, insert the key into the

ignition switch, turn the ignition

switch to the ON position and wait for

30 seconds. Then the system will be

disarmed. (if equipped)

• If you lose your keys, consult your

authorized HYUNDAI dealer.

4 8

Features of your vehicle

DOOR LOCKS

Unlock mode conversion (two stage

unlock mode ↔ central door unlock

mode)

The unlock mode is changed alternately

by pressing the lock button and unlock

button on the transmitter at the same

time for 4 seconds or more. The hazard

warning lights will blink four times to

indicate that the mode conversion is

completed.

Unlock

Lock

• Doors can also be locked and unlocked

with the transmitter.

• Once the doors are unlocked, they may

be opened by pulling the door handle.

• When closing the door, push the door by

hand. Make sure that doors are closed

securely.

❈ If your vehicle is equipped with the

remote keyless entry system, there is no

key lock on the front passenger’s door.

OLM049008

OLM049009

• To lock a door without the key, push the

inside door lock button (1) or central

door lock switch (2 to the “Lock” posi-

)

tion and close the door (3).

Operating door locks from out-

side the vehicle

• Turn the key toward the rear of the

vehicle to unlock and toward the front

of the vehicle to lock.

• If you lock the door with the central

door lock switch (2), all vehicle doors

will lock automatically.

• If you lock the door with a key, all vehi-

cle doors will lock automatically.

• From the driver’s door, turn the key to

the right once to unlock the driver’s

door and once more within 4 seconds

to unlock all doors.

✽

NOTICE

✽

NOTICE

Always remove the ignition key, firmly

engage the parking brake, close all win-

dows and lock all doors when leaving

your vehicle unattended.

• In cold and wet climates, door lock

and door mechanisms may not work

properly due to freezing conditions.

• If the door is locked/unlocked multi-

ple times in rapid succession with

either the vehicle key or door lock

switch, the system may stop operating

temporarily in order to protect the

circuit and prevent damage to system

components.

✽

NOTICE

You can change the system to unlock all

doors by turning the key to the right

once. If you want this feature (central

door unlock mode), perform the follow-

ing:

4 9

Features of your vehicle

• Front doors cannot be locked if the

ignition key is in the ignition switch and

any front door is open.

Driver’s door

WARNING - Door lock mal-

function

Lock

Unlock

If a power door lock ever fails to

function while you are in the vehi-

cle, try one or more of the following

techniques to exit:

OLM049011

• Operate the door unlock feature

repeatedly (both electronic and

manual) while simultaneously

pulling on the door handle.

Passenger’s door

OLM049010

Operating door locks from inside

the vehicle

• Operate the other door locks and

handles, front and rear.

With the door lock button

• To unlock a door, push the door lock

button (1) to the “Unlock” position. The

red mark (2) on button will be visible.

• Lower a front window and use the

key to unlock the door from out-

side.

• To lock a door, push the door lock but-

ton (1) to the “Lock” position. If the door

is locked properly, the red mark (2) on

the door lock button will not be visible.

• Move to the cargo area and open

the tailgate.

OLM049209N

With central door lock switch

Operate by depressing the central door

lock switch.

• To open a door, pull the door handle

(3) outward.

• If the inner door handle of the driver’s

(or front passenger’s) door is pulled

when the door lock button is in lock

position, the button is unlocked and

door opens.

4 10

Features of your vehicle

• When pushing down on the front por-

tion (1) of the switch, all vehicle doors

will lock.

WARNING - Doors

WARNING - Unlocked

vehicles

• The doors should always be fully

closed and locked while the vehi-

cle is in motion to prevent acci-

dental opening of the door.

Locked doors will also discour-

age potential intruders when the

vehicle stops or slows.

• When pushing down on the rear por-

tion (2) of the switch, all vehicle doors

will unlock.

Leaving your vehicle unlocked can

invite theft or possible harm to you

or others from someone hiding in

your vehicle while you are gone.

Always remove the ignition key,

engage the parking brake, close all

windows and lock all doors when

leaving your vehicle unattended.

• If the key is in the ignition switch and

any front door is opened, the doors will

not lock even though the front portion

(1) of central door lock switch is

pressed.

• Be careful when opening doors

and watch for vehicles, motorcy-

cles, bicycles or pedestrians

approaching the vehicle in the

path of the door. Opening a door

when something is approaching

can cause damage or injury.

WARNING - Unattended

children

An enclosed vehicle can become

extremely hot, causing death or

severe injury to unattended chil-

dren or animals who cannot escape

the vehicle. Furthermore, children

might operate features of the vehi-

cle that could injure them, or they

could encounter other harm, possi-

bly from someone gaining entry to

the vehicle. Never leave children or

animals unattended in your vehicle.

4 11

Features of your vehicle

3. Close the rear door.

To open the rear door, pull the outside

door handle.

Auto door lock/unlock feature

• All doors will be automatically locked

when shifting the transaxle shift lever

out of P (Park) with engine is running.

Even though the doors may be unlocked,

the rear door will not open by pulling the

inner door handle (1) until the rear door

• All doors will be automatically unlocked

when shifting the transaxle shift lever

into P (Park) with engine is running.

child safety lock is unlocked ( ).

➡

✽

NOTICE

WARNING - Rear door

locks

An authorized HYUNDAI dealer can

activate or deactivate some auto door

lock/unlock features as follows;

• Speed sensing auto door lock

• Auto door unlock by using the dri-

ver's door lock button

• Auto door unlock when the ignition

key is removed from the ignition

switch

• Auto door lock/unlock by shifting the

transmission shift lever out of P

(Park) or into P (Park)

If you want to activate or deactivate

some door lock/unlock feature, consult

an authorized HYUNDAI dealer.

If children accidentally open the

rear doors while the vehicle is in

motion, they could fall out and be

severely injured or killed. To pre-

vent children from opening the rear

doors from the inside, the rear door

safety locks should be used when-

ever children are in the vehicle.

OLM049012

Child-protector rear door lock

The child safety lock is provided to help

prevent children from accidentally open-

ing the rear doors from inside the vehicle.

The rear door safety locks should be

used whenever children are in the vehi-

cle.

1. Open the rear door.

2. Push the child safety lock located on

the rear edge of the door to the lock

(

) position. When the child safety

lock is in the lock position, the rear

door will not open even though the

inner door handle is pulled.

4 12

Features of your vehicle

TAILGATE

✽

NOTICE

In cold and wet climates, door lock and

door mechanisms may not work proper-

ly due to freezing conditions.

WARNING

The tailgate swings upward. Make

sure no objects or people are near

the rear of the vehicle when open-

ing the tailgate.

OLM049013

OLM049014

Opening the tailgate

Closing the tailgate

CAUTION

• The tailgate is locked or unlocked

when all doors are locked or unlocked

with the key, transmitter or central door

lock switch.

To close the tailgate, lower and push

down the tailgate firmly. Make sure that

the tailgate is securely latched.

Make certain that you close the tail-

gate before driving your vehicle.

Possible damage may occur to the

tailgate lift cylinders and attached

hardware if the tailgate is not

closed prior to driving.

• If unlocked, the tailgate can be opened

by pressing the handle switch and

pulling the handle up.

WARNING - Exhaust

fumes

If you drive with the tailgate open,

you will draw dangerous exhaust

fumes into your vehicle which can

cause serious injury or death to

vehicle occupants.

If you must drive with the tailgate

open, keep the air vents and all win-

dows open so that additional out-

side air comes into the vehicle.

4 13

Features of your vehicle

WARNING - Rear cargo

area

WARNING

• For emergencies, be fully aware

of the location of the emergency

tailgate safety release lever in

this vehicle and how to open the

tailgate if you are accidentally

locked in the luggage compart-

ment.

Occupants should never ride in the

rear cargo area where no restraints

are available. To avoid injury in the

event of an accident or sudden

stops, occupants should always be

properly restrained.

• No one should be allowed to

occupy the luggage compartment

of the vehicle at any time. The

luggage compartment is a very

dangerous location in the event

of a crash.

OLM049015

Emergency tailgate safety release

Your vehicle is equipped with the emer-

gency tailgate safety release lever locat-

ed on the bottom of the tailgate. When

someone is inadvertently locked in the

luggage compartment, if the lever is

pushed, the tailgate latch mechanism is

released and the tailgate is opened by

pushing rearward.

• Use the release lever for emer-

gencies only. Use extreme cau-

tion, especially while the vehicle

is in motion.

4 14

Features of your vehicle

WINDOWS

(1) Driver’s door power window switch

(2) Front passenger’s door power win-

dow switch

(3) Rear door (left) power window switch

(4) Rear door (right) power window

switch

(5) Window opening and closing

(6) Automatic power window up/down*

(Driver’s window)

(7) Power window lock switch

* : if equipped

✽

NOTICE

In cold and wet climates, power windows

may not work properly due to freezing

conditions.

OLM049020N

4 15

Features of your vehicle

Power windows

The ignition switch must be in the ON

position for power windows to operate.

Each door has a power window switch

that controls the door's window. The driv-

er has a power window lock switch which

can block the operation of passenger

windows. The power windows can be

operated for approximately 30 seconds

after the ignition key is removed or turned

to the ACC or LOCK position. However, if

the front doors are opened, the power

windows cannot be operated within the

30 second period after the ignition key

removal.

OLM049021

OLM049022

Window opening and closing

Auto down window (if equipped)

(Driver’s window)

The driver’s door has a master power

window switch that controls all the win-

dows in the vehicle.

Pressing the power window switch

momentarily to the second detent posi-

tion (6) completely lowers the driver’s

window even when the switch is

released. To stop the window at the

desired position while the window is in

operation, pull up the switch momentarily

to the opposite direction of the window

movement.

✽

NOTICE

To open or close a window, press down

or pull up the front portion of the corre-

sponding switch to the first detent posi-

tion (5).

While driving with the rear windows

down or with the sunroof (if equipped)

in an open (or partially open) position,

your vehicle may demonstrate a wind

buffeting or pulsation noise. This noise

is a normal occurrence and can be

reduced or eliminated by taking the fol-

lowing actions. If the noise occurs with

one or both of the rear windows down,

partially lower both front windows

approximately one inch. If you experi-

ence the noise with the sunroof open,

slightly reduce the size of the sunroof

opening.

4 16

Features of your vehicle

✽

NOTICE

The automatic reverse feature for the

driver’s window is only active when the

“auto up” feature is used by fully

pulling up the switch. The automatic

reverse feature will not operate if the

window is raised using the halfway posi-

tion on the power window switch.

WARNING

Always check for obstructions

before raising any window to avoid

injuries or vehicle damage. If an

object less than 0.16 in. (4 mm) in

diameter is caught between the

window glass and the upper win-

dow channel, the automatic reverse

window may not detect the resist-

ance and will not stop and reverse

direction.

OLM049023

OUN026013

Automatic reversal

Auto up/down window (if equipped)

(Driver's window)

If the upward movement of the window is

blocked by an object or part of the body,

the window will detect the resistance and

will stop upward movement. The window

will then lower approximately 11.8 in. (30

cm) to allow the object to be cleared.

Depressing or pulling up the power window

switch momentarily to the second detent

position (6) completely lowers or lifts the

window even when the switch is released.

To stop the window at the desired position

while the window is in operation, pull up or

depress and release the switch to the

opposite direction of the movement.

If the power window is not operated cor-

rectly, the automatic power window system

must be reset as follows:

1. Turn the ignition switch to the ON posi-

tion.

If the window detects the resistance

while the power window switch is pulled

up continuously, the window will stop

upward movement then lower approxi-

mately 1 in. (2.5 cm). And if the power

window switch is pulled up continuously

again within 5 seconds after the window

is lowered by the automatic window

reversal feature, the automatic window

reversal will not operate.

2. Close driver’s window and continue

pulling up on driver’s power window

switch for at least 1 second after the win-

dow is completely closed.

4 17

Features of your vehicle

CAUTION

WARNING - Windows

• NEVER leave the ignition key in

the vehicle.

• To prevent possible damage to

the power window system, do not

open or close two windows or

more at the same time. This will

also ensure the longevity of the

fuse.

• NEVER leave any child unattend-

ed in the vehicle. Even very

young children may inadvertently

cause the vehicle to move, entan-

gle themselves in the windows,

or otherwise injure themselves or

others.

• Never try to operate the main

switch on the driver's door and

the individual door window

switch in opposing directions at

the same time. If this is done, the

window will stop and cannot be

opened or closed.

• Always double check to make

sure all arms, hands, head and

other obstructions are safely out

of the way before closing a win-

dow.

OLM049024

Power window lock button

• The driver can disable the power win-

dow switches on the passenger doors

by depressing the power window lock

switch located on the driver’s door to

LOCK (pressed).

• Do not allow children to play with

the power windows. Keep the dri-

ver’s door power window lock

switch in the LOCK position

(depressed). Serious injury can

result from unintentional window

operation by the child.

• When the power window lock switch

is ON, the driver’s master control

cannot operate the passenger door

power windows.

• Do not extend any head or arms

outside through the window

opening while driving.

4 18

Features of your vehicle

HOOD

OLM049025

OLM049026

OLM049027

2. Go to the front of the vehicle, raise the

hood slightly, pull the secondary latch

(1) inside of the hood center and lift

the hood (2).

3.Pull out the support rod from the

engine room.

Opening the hood

1. Pull the release lever to unlatch the

hood. The hood should pop open

slightly.

4.Hold the hood open with the support

rod.

WARNING - Hot parts

Grasp the support rod in the area

wrapped in rubber. The rubber will

help prevent you from being burned

by hot metal when the engine is

hot.

4 19

Features of your vehicle

Closing the hood

1. Before closing the hood, check the fol-

lowing:

• All filler caps in engine compartment

must be correctly installed.

• Gloves, rags or any other com-

bustible material must be removed

from the engine compartment.

WARNING

• Before closing the hood, ensure

that all obstructions are removed

from the hood opening. Closing

the hood with an obstruction

present in the hood opening may

result in property damage or

severe personal injury.

2. Return the support rod to its clip to

prevent it from rattling.

• Do not leave gloves, rags or any

other combustible material in the

engine compartment. Doing so

may cause a heat-induced fire.

3. Lower the hood until it is about 1 ft. (30

cm) above the closed position and let

it drop. Make sure that it locks into

place.

• Always double check to be sure

that the hood is firmly latched

before driving away. If it is not

latched, the hood could open

while the vehicle is being driven,

causing a total loss of visibility,

which might result in an accident.

• Do not move the vehicle with the

hood in the raised position, as

vision is obstructed and the hood

could fall or be damaged.

4 20

Features of your vehicle

FUEL FILLER DOOR

Closing the fuel filler door

1. To install the cap, turn it clockwise until

it “clicks” one time. This indicates that

the cap is securely tightened.

2. Close the fuel filler door and push it

lightly making sure that it is securely

closed.

WARNING - Refueling

• If pressurized fuel sprays out, it

can cover your clothes or skin

and thus subject you to the risk

of fire and burns. Always remove

the fuel cap carefully and slowly.

If the cap is venting fuel or if you

hear a hissing sound, wait until

the condition stops before com-

pletely removing the cap.

OSA047022

OLM049028

1. Stop the engine.

2. To open the fuel filler door, pull the fuel

filler door opener up.

Opening the fuel filler door

The fuel filler door must be opened from

inside the vehicle by pulling up the fuel

filler door opener lever.

3. Pull the fuel filler door (1) out to fully

open.

4. To remove the cap, turn the fuel filler

cap (2) counterclockwise.

5. Refuel as needed.

✽

NOTICE

• Do not "top off" after the nozzle

automatically shuts off when

refueling.

If the fuel filler door does not open

because ice has formed around it, tap

lightly or push on the door to break the

ice and release the door. Do not pry on

the door. If necessary, spray around the

door with an approved de-icer fluid (do

not use radiator anti-freeze) or move the

vehicle to a warm place and allow the ice

to melt.

• Tighten the cap until it clicks one

time, otherwise the Check Engine

light will illuminate.

• Always check that the fuel cap is

installed securely to prevent fuel

spillage in the event of an acci-

dent.

4 21

Features of your vehicle

(Continued)

WARNING - Refueling dan-

gers

Use only approved portable plas-

tic fuel containers designed to

carry and store gasoline.

• Do not get back into a vehicle

once you have begun refueling

since you can generate static

electricity by touching, rubbing

or sliding against any item or fab-

ric (polyester, satin, nylon, etc.)

capable of producing static elec-

tricity. Static electricity discharge

can ignite fuel vapors resulting in

rapid burning. If you must re-

enter the vehicle, you should

once again eliminate potentially

dangerous static electricity dis-

charge by touching a metal part

of the vehicle, away from the fuel

filler neck, nozzle or other gaso-

line source.

Automotive fuels are flammable

materials. When refueling, please

note the following guidelines care-

fully. Failure to follow these guide-

lines may result in severe personal

injury, severe burns or death by fire

or explosion.

• Do not use cellular phones while

refueling. Electric current and/or

electronic interference from cel-

lular phones can potentially

ignite fuel vapors causing a fire.

• When refueling, always shut the

engine off. Sparks produced by

electrical components related to

the engine can ignite fuel vapors

causing a fire. Once refueling is

complete, check to make sure the

filler cap and filler door are

securely closed, before starting

the engine.

• Read and follow all warnings

posted at the gas station facility.

• Before refueling, note the loca-

tion of the Emergency Gasoline

Shut-Off, if available, at the gas

station facility.

• Before touching the fuel nozzle,

you should eliminate potentially

dangerous static electricity dis-

charge by touching another metal

part of the vehicle, a safe dis-

tance away from the fuel filler

neck, nozzle, or other gas source.

• DO NOT use matches or a lighter

and DO NOT SMOKE or leave a lit

cigarette in your vehicle while at

a gas station especially during

refueling. Automotive fuel is

highly flammable and can, when

ignited, result in fire.

• When

using

an

approved

portable fuel container, be sure to

place the container on the

ground prior to refueling. Static

electricity discharge from the

container can ignite fuel vapors

causing a fire. Once refueling has

begun, contact with the vehicle

should be maintained until the

filling is complete.

(Continued)

4 22

Features of your vehicle

(Continued)

CAUTION

• If a fire breaks out during refuel-

ing, leave the vicinity of the vehi-

cle, and immediately contact the

manager of the gas station and

then contact the local fire depart-

ment or 911. Follow any safety

instructions they provide.

• Make sure to refuel your vehicle

according to the "Fuel require-

ments" suggested in section 1.

• If the fuel filler cap requires

replacement, use only a genuine

HYUNDAI cap or the equivalent

specified for your vehicle. An

incorrect fuel filler cap can result

in a serious malfunction of the

fuel system or emission control

system.

• Do not spill fuel on the exterior

surfaces of the vehicle. Any type

of fuel spilled on painted surfaces

may damage the paint.

• After refueling, make sure the fuel

cap is installed securely to pre-

vent fuel spillage in the event of

an accident.

4 23

Features of your vehicle

PANORAMIC SUNROOF (IF EQUIPPED)

Sunroof open warning chime

(if equipped)

CAUTION

• Do not continue to move the sun-

roof control lever after the sunroof

is fully opened, closed, or tilted.

Damage to the motor or system

components could occur.

If the driver removes the ignition key

(smart key: turns off the engine) and

opens the driver-side door when the sun-

roof is not fully closed, the warning chime

will sound for approximately 7 seconds.

• Make sure the sunroof is closed

fully when leaving your vehicle. If

the sunroof is open, rain or snow

may leak through the sunroof and

wet the interior as well as cause

theft.

However, if the smart key is in the smart

key holder, the warning chime will not

sound.

Close the sunroof securely when leaving

your vehicle.

OLM049030

If your vehicle is equipped with a sunroof,

you can slide or tilt your sunroof with the

sunroof control lever located on the over-

head console.

✽

NOTICE

• In cold and wet climates, the sunroof

✽

NOTICE

may not work properly due to freez- The sunroof cannot tilt when it is in the

ing conditions.

slide position but can be slid while in a

• After a vehicle is washed or in a rain- tilt position.

storm be sure to wipe off any water

that is on the sunroof before operating

it.

The sunroof can only be opened, closed,

or tilted when the ignition switch is in the

ON position.

4 24

Features of your vehicle

To open the sunroof automatically:

WARNING

Pull the sunroof control lever backward to

the second detent position and then

release it. The sunroof will slide open

automatically open all the way.

• Never adjust the sunroof or roller

blind while driving. This could

result in loss of control and an

accident that may cause death,

serious injury, or property dam-

age.

To stop the sunroof sliding at any point,

pull or push the sunroof control lever

momentarily.

• HYUNDAI does not recommend

installing a roof rack on a vehicle

with the panoramic sunroof.

To close the sunroof automatically:

Push the sunroof control lever forward to

the second detent position and then

release it. The sunroof will automatically

close all the way.

• All occupants of the vehicle must

wear their seat belts at all times.

Seat belts and child restraints

reduce serious or fatal injuries

for all occupants in the event of a

collision or sudden stop.

OLM049031

Sliding the sunroof

Before opening or closing the sunroof,

open the roller blind.

To open the sunroof (manual slide fea-

ture), pull the sunroof control lever back-

ward to the first detent position.

To stop the sunroof sliding at any point,

pull or push the sunroof control lever

momentarily.

To close the sunroof (manual slide fea-

ture), push or pull the sunroof control

lever with safety switch (1) forward or

downward to the first detent position.

WARNING

Do not allow children operate the

sunroof. Closing a sunroof on

someone can cause serious injury,

and in some cases, even death.

4 25

Features of your vehicle

WARNING - Sunroof

• Be careful that no head, hands

and body parts are obstructed by

a closing sunroof.

• Do not extend the face, neck,

arms or body outside the sunroof

while driving.

• Make sure your hands and head

are safely out of the way before

closing a sunroof.

OXM049029

OLM049032

Automatic reversal

Tilting the sunroof

CAUTION

• Periodically remove any dirt that

may accumulate on the guide rail.

If an object is detected while the sunroof is

closing automatically, it will reverse the

direction, and then stop.

Before opening or closing the sunroof,

open the roller blind.

To open the sunroof (manual feature),

push the sunroof control lever upward

until the sunroof moves to the desired

position.

• If you try to open the sunroof

when the temperature is below

freezing or when the sunroof is

covered with snow or ice, the

glass or the motor could be dam-

aged.

The auto reverse function does not work if

a small obstacle is between the sliding

glass and the sunroof sash. You should

always check that all passengers and

objects are away from the sunroof before

closing it.

To close the sunroof, pull the sunroof

lever downward until the sunroof moves

to the desired position.

• Do not leave the roller blind

closed while the sunroof is

opened.

WARNING

• Never activate the auto reverse

function intentionally with any of

your body parts.

• The auto reverse function may not

work if something gets caught just

before the sunroof fully closes.

4 26

Features of your vehicle

Resetting the sunroof

Whenever the vehicle battery is discon-

nected or discharged, you must reset

your sunroof system as follows:

1. Turn the ignition switch to the ON

position.

2. Open the roller blind.

3. Close the sunroof.

4. Release the sunroof control lever.

5. Push the sunroof control lever forward

in the direction of close (about 10 sec-

onds) until the sunroof is moved a lit-

tle. Then, release the lever.

6. Push the sunroof control lever forward

in the direction of close until the sun-

roof operates as follows;

OXM049031N

Roller blind

The roller blinds are installed inside of

the sunroof and glass roof.

Open or close the roller blind manually

using the handle (1) when you need to.

TILT OPEN → SLIDE OPEN →

SLIDE CLOSE

Before opening or closing the sunroof,

open the roller blind.

Then, release the lever.

CAUTION

Operation of the roller blind without

using the handle (1) may cause mis-

alignment or malfunction.

When this is complete, the sunroof sys-

tem has been reset.

✽

NOTICE

It is normal for wrinkles to form on the

blind because of its material character-

istic.

4 27

Features of your vehicle

STEERING WHEEL

Electric power steering

Tilt steering/Telescope steering

(if equipped)

Tilt steering allows you to adjust the

steering wheel before you drive. You can

also raise the steering wheel to give your

legs more room when you exit and enter

the vehicle (if equipped).

✽

NOTICE

The following symptoms may occur dur-

ing normal vehicle operation:

The power steering uses a motor to

assist you in steering the vehicle. If the

engine is off or if the power steering sys-

tem becomes inoperative, the vehicle

may still be steered, but it will require

increased steering effort.

• The EPS warning light does not illu-

minate.

• The steering wheel becomes heavier

after turning the ignition switch on.

This happens as the system performs

the EPS system diagnostics. When the

diagnostics is completed, the steering

wheel will return to its normal condi-

tion.

The motor driven power steering is con-

trolled by a power steering control unit

which senses the steering wheel torque,

steering wheel position and vehicle

speed to command the motor.

The steering wheel should be positioned

so that it is comfortable for you to drive,

while permitting you to see the instru-

ment panel warning lights and gauges.

• Click noise may be heard from the

EPS relay after the ignition switch is

turned to the ON or LOCK position.

• Motor noise may be heard when the

vehicle is at a stop or at a low driving

speed.

• If the Electric Power Steering System

does not operate normally, the warn-

ing light will illuminate on the instru-

ment cluster. The steering wheel may

become difficult to control or operate

abnormally. Take your vehicle to an

authorized HYUNDAI dealer and

have the vehicle checked as soon as

possible.

The steering wheel becomes heavier as

the vehicle’s speed increases and

becomes lighter as the vehicle’s speed

decreases for optimum steering control.

WARNING

• Never adjust the angle and height

of steering wheel while driving.

You may lose your steering con-

trol and cause severe personal

injury or accidents.

Should you notice any change in the

effort required to steer during normal

vehicle operation, have the power steer-

ing checked by an authorized HYUNDAI

dealer.

• After adjusting, push the steering

wheel both up and down to be

certain it is locked in position.

• When you operate the steering wheel

in low temperature, abnormal noise

could occur. If temperature rises, the

noise will disappear. This is a normal

condition.

4 28

Features of your vehicle

CAUTION

Do not strike the horn severely to

operate it, or hit it with your fist. Do

not press on the horn with a sharp-

pointed object.

OLM049033L

OLM049034

To change the steering wheel angle, pull

down the lock-release lever (1), adjust

the steering wheel to the desired angle

(2) and the desired position (if equipped)

(3), then pull up the lock-release lever to

lock the steering wheel in place. Be sure

to adjust the steering wheel to the

desired position before driving.

Horn

To sound the horn, press the horn sym-

bol on your steering wheel.

Check the horn regularly to be sure it

operates properly.

✽

NOTICE

To sound the horn, press the area indi-

cated by the horn symbol on your steer-

ing wheel (see illustration). The horn

will operate only when this area is

pressed.

4 29

Features of your vehicle

MIRRORS

Inside rearview mirror

CAUTION

Adjust the rearview mirror to center on

the view through the rear window. Make

this adjustment before you start driving.

When cleaning the mirror, use a

paper towel or similar material

dampened with glass cleaner. Do

not spray glass cleaner directly on

the mirror as the liquid cleaner may

enter the mirror housing.

Night

WARNING - Rear visibility

Do not place objects in the rear

seat or cargo area which would

interfere with your vision through

the rear window.

Day

OLM049035

Day/night rearview mirror

Make this adjustment before you start

driving and while the day/night lever is in

the day position.

Pull the day/night lever toward you to

reduce glare from the headlights of vehi-

cles behind you during night driving.

Remember that you lose some rearview

clarity in the night position.

4 30

Features of your vehicle

Outside rearview mirror

CAUTION

WARNING

Be sure to adjust mirror angles before

driving.

Do not scrape ice off the mirror

face; this may damage the surface

of the glass. If ice should restrict

movement of the mirror, do not

force the mirror for adjustment. To

remove ice, use a deicer spray, or a

sponge or soft cloth with warm

water.

Do not adjust or fold the outside

rearview mirrors while the vehicle

is moving. This could result in loss

of control, and an accident which

could cause death, serious injury

or property damage.

Your vehicle is equipped with both left-

hand and right-hand outside rearview

mirrors. The mirrors can be adjusted

remotely with the remote switch. The mir-

ror heads can be folded back to prevent

damage during an automatic car wash or

when passing in a narrow street.

WARNING - Rearview mir-

rors

• The right outside rearview mirror

is convex. Objects seen in the

mirror are closer than they

appear.

CAUTION

If the mirror is jammed with ice, do

not adjust the mirror by force. Use

an approved spray de-icer (not radi-

ator antifreeze) to release the

frozen mechanism or move the

vehicle to a warm place and allow

the ice to melt.

• Use your interior rearview mirror

or direct observation to deter-

mine the actual distance of fol-

lowing vehicles when changing

lanes.

4 31

Features of your vehicle

CAUTION

• The mirrors stop moving when

they reach the maximum adjust-

ing angles, but the motor contin-

ues to operate while the switch is

depressed. Do not depress the

switch longer than necessary, the

motor may be damaged.

• Do not attempt to adjust the out-

side rearview mirror by hand.

Doing so may damage the parts.

OLM049039

Remote control

The electric remote control mirror switch

allows you to adjust the position of the

left and right outside rearview mirrors. To

adjust the position of either mirror, push

the switch (1) to R or L to select the right

side mirror or the left side mirror, then

press a corresponding point on the mirror

adjustment control to position the select-

ed mirror up, down, left or right.

After adjustment, put the switch into neu-

tral (center) position to prevent the inad-

vertent adjustment.

4 32

Features of your vehicle

INSTRUMENT CLUSTER

1. Tachometer

2. Turn signal indicators

3. Speedometer

4. Engine temperature gauge

5. Shift position indicator

6. Fuel gauge

7. Odometer/Trip computer*

8. Warning and indicator lights

* : if equipped

* The actual cluster in the vehicle may differ from the illustration.

For more details refer to the "Gauges" in the next pages.

OLM049051N

4 33

Features of your vehicle

OLM049052

OLM049054N

OLM049056

Tachometer

Instrument panel illumination

Gauges

The tachometer indicates the approxi-

mate number of engine revolutions per

minute (rpm).

When the vehicle’s parking lights or

headlights are on, press the illumination

control button to adjust the brightness of

the instrument panel illumination.

Speedometer

The speedometer indicates the forward

speed of the vehicle.

Use the tachometer to select the correct

shift points and to prevent lugging and/or

over-revving the engine.

The speedometer is calibrated in miles

per hour and/or kilometers per hour.

When the door is open, or if the engine is

not started within 1 minute, the tachome-

ter pointer may move slightly in ON posi-

tion with the engine OFF. This movement

is normal and will not affect the accuracy

of the tachometer once the engine is run-

ning.

4 34

Features of your vehicle

CAUTION

Do not operate the engine within

the tachometer's RED ZONE.

WARNING

Never remove the radiator cap

when the engine is hot. The engine

coolant is under pressure and

could cause severe burns. Wait

until the engine is cool before

adding coolant to the reservoir.

This may cause severe engine dam-

age.

OLM049057

Engine temperature gauge

This gauge shows the temperature of the

engine coolant when the ignition switch

is ON.

Do not continue driving with an overheat-

ed engine. If your vehicle overheats, refer

to “If the engine overheats” in section 6.

CAUTION

If the gauge pointer moves beyond

the normal range area toward the

“H” position, it indicates overheat-

ing that may damage the engine.

4 35

Features of your vehicle

WARNING - Fuel gauge

Running out of fuel can expose

vehicle occupants to danger.

You must stop and obtain addition-

al fuel as soon as possible after the

warning light comes on or when the

gauge indicator comes close to the

E level.

CAUTION

OLM049058

OLM049059

Avoid driving with a extremely low

fuel level. Running out of fuel could

cause the engine to misfire, damag-

ing the catalytic converter.

Fuel gauge

Trip computer

The fuel gauge indicates the approxi-

mate amount of fuel remaining in the fuel

tank. The fuel tank capacity is given in sec-

tion 8. The fuel gauge is supplemented by

a low fuel warning light, which will illumi-

nate when the fuel tank is near empty.

The trip computer is a microcomputer-

controlled driver information system that

displays information related to driving,

including odometer, tripmeter, distance

to empty, average fuel consumption,

average speed, driving time and ECO

ON/OFF mode (if equipped) on the dis-

play when the ignition switch is in the ON

position. All stored driving information

(except odometer and distance to empty)

is reset if the battery is disconnected.

On inclines or curves, the fuel gauge

pointer may fluctuate or the low fuel

warning light may come on earlier than

usual due to the movement of fuel in the

tank.

The bottom segment will flash as the fuel

level approaching empty.

4 36

Features of your vehicle

The odometer is always displayed until

the display is turned off.

Push the TRIP button for less than 1 sec-

ond to select tripmeter, distance to

empty, average fuel consumption, aver-

age speed, driving time and ECO

ON/OFF mode* function as follows:

Tripmeter

Distance to empty

Average fuel consumption

Average speed

OLM049060N

OLM049061N

Odometer

The odometer indicates the total dis-

tance the vehicle has been driven.

Tripmeter

This mode indicates the distance of indi-

vidual trips selected since the last trip-

meter reset.

You will also find the odometer useful to

determine when periodic maintenance

should be performed.

The meter's working range is from 0.0 to

999.9 miles (0.0 to 999.9 km).

Driving time

Pressing the TRIP button for more than 1

second, when the tripmeter is being dis-

played, clears the tripmeter to zero (0.0).

ECO ON/OFF mode*

* : if equipped

4 37

Features of your vehicle

✽

NOTICE

• If the vehicle is not on level ground or

the battery power has been interrupt-

ed, the “Distance to empty” function

may not operate correctly.

The trip computer may not register

additional fuel if less than 1.6 gallons (6

liters) of fuel are added to the vehicle.

• The fuel consumption and distance to

empty values may vary significantly

based on driving conditions, driving

habits, and condition of the vehicle.

• The distance to empty value is an esti-

mate of the available driving distance.

This value may differ from the actual

driving distance available.

OLM049062N

OLM049064N

Distance to empty

Average fuel consumption

This mode indicates the estimated dis-

tance to empty based on the current fuel

in the fuel tank and the amount of fuel

delivered to the engine. When the

remaining distance is below 30 miles (50

km), “----” will be displayed and the dis-

tance to empty indicator will blink.

This mode calculates the average fuel

consumption from the total fuel used and

the distance since the last average con-

sumption reset. The total fuel used is cal-

culated from the fuel consumption input.

For an accurate calculation, drive more

than 0.03 miles (50 m).

The meter’s working range is from 30 to

990 miles (50 to 990 km).

Pressing the TRIP button for more than 1

second, when the average fuel consump-

tion is being displayed, clears the average

fuel consumption to zero (--.-).

4 38

Features of your vehicle

OLM049066N

OLM049067N

OLM049068N

Average speed

Driving time

This mode indicates the total time trav-

eled since the last driving time reset.

ECO ON/OFF mode (if equipped)

This mode calculates the average speed

of the vehicle since the last average

speed reset.

You can turn the ECO indicator on/off on

the instrument cluster in this mode.

If you push the TRIP button more than 1

second in the ECO ON mode, ECO OFF

is displayed in the screen and the ECO

indicator turns off.

Even if the vehicle is not in motion, the

driving time is calculated while the

engine is running.

Even if the vehicle is not in motion, the

average speed is calculated while the

engine is running.

The meter’s working range is from

0:00~99:59.

If you want to display the ECO indicator

again, press the TRIP button more than 1

second in the ECO OFF mode and then

ECO ON mode is displayed in the

screen.

Pressing the TRIP button for more than 1

second, when the average speed is

being displayed, clears the average

speed to zero (---).

Pressing the TRIP button for more than 1

second, when the driving time is being

displayed, clears the driving time to zero

(0:00).

When you press the TRIP button less

than 1 second in the ECO mode, the

mode is changed to odometer.

4 39

Features of your vehicle

ECO indicator (if equipped)

Air bag warning light

Warnings and indicators

ECO

All warning lights are checked by turning

the ignition switch ON (do not start the

engine). Any light that does not illuminate

should be checked by an authorized

HYUNDAI dealer.

This warning light will illuminate for

approximately 6 seconds each time you

turn the ignition switch to the ON posi-

tion.

The ECO indicator is a system that helps

you to drive economically.

It is displayed if you drive fuel efficiently

to help you improve fuel efficiency.

After starting the engine, check to make

sure that all warning lights are off. If any

are still on, this indicates a situation that

needs attention. When releasing the

parking brake, the brake system warning

light should go off. The fuel warning light

will stay on if the fuel level is low.

This light also comes on when the

Supplemental Restraint System (SRS) is

not working properly. If the AIR BAG

warning light does not come on, or con-

tinuously remains on after operating for

about 6 seconds when you turned the

ignition switch to the ON position or start-

ed the engine, or if it comes on while

driving, have the SRS inspected by an

authorized HYUNDAI dealer.

• The ECO indicator (green) will turn on

when you are driving fuel efficiently in

the ECO ON mode.

If you don't want the indicator dis-

played, you can turn the ECO ON

mode to OFF mode by pressing the

TRIP button.

As per ECO ON/OFF Mode operation,

refer to the previous page.

• The fuel-efficiency can be changed by

the driver's driving habit and road con-

dition.

• The ECO indicator does not function in

P (Park), N (Neutral), and R (Reverse).

WARNING

Don't keep watching the indicator

while driving. It will distract you

while driving and cause an acci-

dent that results in severe personal

injury.

4 40

Features of your vehicle

Electronic brake

force distribution

(EBD) system

Anti-lock brake system

(ABS) warning light

✽

NOTICE

If the ABS warning light or EBD warn-

ing light is on and stays on, the

speedometer or odometer/tripmeter

may not work. Also, the EPS warning

light may illuminate and the steering

effort may increase or decrease. In this

case, have your vehicle checked by an

authorized HYUNDAI dealer as soon as

possible.

warning light

If two warning lights shown illuminate at

the same time while driving, your vehicle

may have a malfunction with ABS and

EBD system.

This light illuminates if the ignition switch

is turned ON and goes off in approxi-

mately 3 seconds if the system is operat-

ing normally.

In this case, your ABS and regular brake

system may not work normally. Have the

vehicle checked by an authorized

HYUNDAI dealer as soon as possible.

If the ABS warning light remains on,

comes on while driving, or does not

come on when the ignition switch is

turned to the ON position, this indicates

that there may be a malfunction with the

ABS.

WARNING

If this occurs, have your vehicle checked

by an authorized HYUNDAI dealer as

soon as possible. The normal braking

system will still be operational, but with-

out the assistance of the anti-lock brake

system.

If both ABS and Brake warning

lights are on and stay on, your vehi-

cle’s brake system will not work

normally. So you may experience

an unexpected and dangerous situ-

ation during sudden braking. In this

case, avoid high speed driving and

abrupt braking. Have your vehicle

checked by an authorized HYUNDAI

dealer as soon as possible.

4 41

Features of your vehicle

Parking brake & brake

fluid warning light

3. Do not drive the vehicle if leaks are

found, the warning light remains on or

the brakes do not operate properly.

Have the vehicle towed to any author-

ized HYUNDAI dealer for a brake sys-

tem inspection and necessary repairs.

Seat belt warning

As a reminder to the driver, the seat belt

warning light will blink for approximately

6 seconds each time you turn the ignition

switch ON, regardless of belt fastening.

Parking brake warning

This light is illuminated when the parking

brake is applied with the ignition switch in

the START or ON position. The warning

light should go off when the parking

brake is released while engine is run-

ning.

Your vehicle is equipped with a dual-

diagonal braking system.This means you

still have braking on two wheels even if

one of the brake circuits is damaged or

malfunctions.With only one of the circuits

working, more than normal pedal travel

and greater pedal pressure are required

to stop the car. Also, the car will not stop

in as short a distance with only a portion

of the brake system working. If the

brakes fail while you are driving, shift to a

lower gear for additional engine braking

and stop the car as soon as it is safe to

do so.

For details, refer to the seat belt on chap-

ter 3.

Turn signal indicator

The parking brake warning chime will

sound to remind you that the parking

brake is applied when you are driving

above 6 mph (10 km/h). Always release

the parking brake before you drive.

The blinking green arrows on the instru-

ment panel show the direction indicated

by the turn signals. If the arrow comes on

but does not blink, blinks more rapidly

than normal, or does not illuminate at all,

a malfunction in the turn signal system is

indicated. Your dealer should be consult-

ed for repairs.

Low brake fluid level warning

If the warning light remains on, it may

indicate that the brake fluid level in the

reservoir is low.

To check bulb operation, check whether

the parking brake and brake fluid warning

light illuminates when the ignition switch

is in the ON position.

If the warning light remains on:

1. Drive carefully to the nearest safe

location and stop your vehicle.

This indicator also blinks when the haz-

ard warning switch is turned on.

2. With the engine stopped, check the

brake fluid level immediately and add

fluid as required. Then check all brake

components for fluid leaks.

WARNING

Driving the vehicle with a warning

light on is dangerous. If the brake

warning light remains on, have the

brakes checked and repaired imme-

diately by an authorized HYUNDAI

dealer.

4 42

Features of your vehicle

Light on indicator

Engine oil pressure

warning light

CAUTION

If the oil pressure warning light

stays on while the engine is run-

ning, serious engine damage may

result. The oil pressure warning

light comes on whenever there is

insufficient oil pressure. In normal

operation, it should come on when

the ignition switch is turned on,

then go out when the engine is

started. If the oil pressure warning

light stays on while the engine is

running, there is a serious malfunc-

tion.

This warning light indicates the engine oil

pressure is low.

The indicator illuminates when the tail

lights or headlights are ON.

If the warning light illuminates while driv-

ing:

High beam indicator

1. Drive safely to the side of the road and

stop.

2. With the engine off, check the engine

oil level. If the level is low, add oil as

required.

This indicator illuminates when the head-

lights are on and in the high beam posi-

tion or when the turn signal lever is pulled

into the Flash-to-Pass position.

If the warning light remains on after

adding oil or if oil is not available, call an

authorized HYUNDAI dealer.

If this happens, stop the car as

soon as it is safe to do so, turn off

the engine and check the oil level. If

the oil level is low, fill the engine oil

to the proper level and start the

engine again. If the light stays on

with the engine running, turn the

engine off immediately. In any

instance where the oil light stays on

when the engine is running, the

engine should be checked by an

authorized HYUNDAI dealer before

the car is driven again.

Front fog light indicator

(if equipped)

CAUTION

If the engine is not stopped imme-

diately after the engine oil pressure

warning light is illuminated, severe

damage could result.

The indicator illuminates when the front

fog lights are ON.

4 43

Features of your vehicle

Shift pattern indicator

(if equipped)

Charging system warning

light

Door ajar warning light

This warning light indicates a malfunction

of either the generator or electrical

charging system.

The indicator displays which automatic

transaxle shift position is selected.

This warning light illuminates when a

door is not closed securely with the igni-

tion switch in any position.

If the warning light comes on while the

vehicle is in motion:

1. Drive to the nearest safe location.

Manual transaxle shift

indicator (if equipped)

Tailgate open warning light

2. With the engine off, check the genera-

tor drive belt for looseness or break-

age.

This indicator informs you which gear is

desired while driving to save fuel.

For example

This warning light illuminates when the

tailgate is not closed securely with the

ignition switch in any position.

3. If the belt is adjusted properly, a prob-

lem exists somewhere in the electrical

charging system. Have an authorized

HYUNDAI dealer correct the problem

as soon as possible.

: Indicates that shifting up to the 3rd

gear is desired (currently the shift

lever is in the 2nd gear).

Low fuel level warning light

: Indicates that shifting down to the

3rd gear is desired (currently the

shift lever is in the 4th gear).

This warning light indicates the fuel tank

is nearly empty. When it comes on, you

should add fuel as soon as possible.

Driving with the fuel level warning light on

or with the fuel level below “E” can cause

the engine to misfire and damage the

catalytic converter.

✽

NOTICE

When the system is not working proper-

ly, up & down arrow indicator and Gear

are not displayed.

4 44

Features of your vehicle

Malfunction indicator (MIL)

(check engine light)

ESC indicator (Electronic

Stability Control)

(if equipped)

CAUTION

• Prolonged driving with the

Emission Control System

Malfunction Indicator Light illumi-

nated may cause damage to the

emission control systems which

could effect drivability and/or fuel

economy.

The ESC indicator will illuminate when

the ignition switch is turned ON, but

should go off after approximately 3 sec-

onds. When the ESC is on, it monitors

the driving conditions and under normal

driving conditions, the ESC indicator will

remain off. When a slippery or low trac-

tion condition is encountered, the ESC

will operate, and the ESC indicator will

blink to indicate the ESC is operating. If

the ESC system malfunctions the indica-

tor illuminates and stays on. Take your

vehicle to an authorized HYUNDAI deal-

er and have the system checked.

This indicator light is part of the Engine

Control System which monitors various

emission control system components. If

this light illuminates while driving, it indi-

cates that a potential malfunction has

been detected somewhere in the emis-

sion control system.

•

If the Emission Control System

Malfunction Indicator Light illumi-

nates, potential catalytic converter

damage is possible which could

result in loss of engine power.

Have the Engine Control System

inspected as soon as possible by

an authorized HYUNDAI dealer.

This light will also illuminate when the

ignition switch is turned to the ON posi-

tion, and will go out in a few seconds

after the engine is started. If it illuminates

while driving, or does not illuminate when

the ignition switch is turned to the ON

position, take your vehicle to your near-

est authorized HYUNDAI dealer and

have the system checked.

ESC OFF indicator

(if equipped)

Generally, your vehicle will continue to be

drivable, but have the system checked by

an authorized HYUNDAI dealer promptly.

The ESC OFF indicator will illuminate

when the ignition switch is turned ON,

but should go off after approximately 3

seconds. To switch to ESC function off,

press the ESC OFF button. The ESC

OFF indicator will illuminate indicating

the ESC is deactivated.

4 45

Features of your vehicle

DBC (Downhill brake con-

trol) indicator (if equipped)

AWD system warning light

(if equipped)

Low tire pressure indica-

tor

The low tire pressure telltale comes on

for 3 seconds after the ignition switch is

turned to the "ON" position.

The DBC indicator will illuminate when

the DBC button is pressed and the sys-

tem is on.

When the ignition switch is turned to the

ON position, the AWD indicator will illu-

minate and then go off in a few seconds.

The low tire pressure telltale illuminates

when one or more of your tires is signifi-

cantly underinflated.

When driving down a steep hill at a

speed under 22 mph (35 km/h), the DBC

will operate and the DBC indicator will

blink to indicate the DBC is operating.

If the AWD system warning light

illuminates, this indicates that there is a

malfunction in the AWD system. If this

occurs, have your vehicle checked by an

authorized HYUNDAI dealer as soon as

possible.

The low tire pressure telltale will illumi-

nate after it blinks for approximately one

minute when there is a problem with the

Tire Pressure Monitoring System.

If the red indicator illuminates, the DBC

system may have malfunctioned. Take

your vehicle to an authorized HYUNDAI

dealer and have the system checked.

AWD LOCK indicator

(if equipped)

If this occurs, have the system checked

by an authorized HYUNDAI dealer as

soon as possible.

For details, refer to the TPMS on section 6.

The AWD LOCK indicator light is illumi-

nated when the AWD LOCK button is

pushed. The purpose of this AWD LOCK

mode is to increase the drive power

when driving on wet pavement, snow-

covered roads and/or off-road. The AWD

LOCK indicator light is turned off by

pushing the button again.

WARNING - Safe stopping

• The TPMS cannot alert you to

severe and sudden tire damage

caused by external factors.

• If you feel any vehicle instability,

immediately take your foot off the

accelerator, apply the brakes

gradually and with light force,

and slowly move to a safe posi-

tion off the road.

CAUTION

Do not use AWD LOCK mode on dry

paved roads or highway, it can

cause noise, vibration or damage of

AWD related parts.

4 46

Features of your vehicle

Engine coolant

temperature warning light

(if equipped)

Cruise indicator

CRUISE indicator

Key reminder warning chime

If the driver’s door is opened while the

ignition key is left in the ignition switch

(ACC or LOCK position), the key

reminder warning chime will sound. This

is to prevent you from locking your keys

in the vehicle.The chime sounds until the

key is removed from the ignition switch or

the driver’s door is closed.

CRUISE

The warning light illuminates if the tem-

perature of the engine coolant is above

248 5.4°F (120 3°C).

The indicator light illuminates when the

cruise control system is enabled.

Do not continue driving with an overheat-

ed engine. If your vehicle overheats, refer

to “Overheating” in section 6.

The cruise indicator light in the instru-

ment cluster is illuminated when the

cruise control ON-OFF button on the

steering wheel is pushed.

✽

NOTICE

The indicator light turns off when the

cruise control ON-OFF button is pushed

again. For more information about the

use of cruise control, refer to “Cruise

control system” in section 5.

If the engine coolant temperature warn-

ing light illuminates, it indicates over-

heating that may damage the engine.

Electric power steering

(EPS) system warning light

Cruise SET indicator

EPS

SET

This indicator light comes on after the

ignition key is turned to the ON position

and then it will go out after the engine is

started.

The indicator light illuminates when the

cruise function switch (SET- or RES+) is

ON.

This light also comes on when the EPS

has some troubles. If it comes on while

driving, have your vehicle inspected by

an authorized HYUNDAI dealer.

The cruise SET indicator light in the

instrument cluster is illuminated when

the cruise control switch (SET- or RES+)

is pushed. The cruise SET indicator light

does not illuminate when the cruise con-

trol switch (CANCEL) is pushed or the

system is disengaged.

4 47

Features of your vehicle

HAZARD WARNING FLASHER

REARVIEW CAMERA (IF EQUIPPED)

WARNING

• This system is a supplementary

function only. It is the responsi-

bility of the driver to always

check the inside/outside rearview

mirror and the area behind the

vehicle before and while backing

up.

• Always keep the camera lens

clean. If lens is covered with for-

eign matter, the camera may not

operate normally.

OLM049081

Rear view display

OLM049084

The hazard warning flasher should be

used whenever you find it necessary to

stop the car in a hazardous location.

When you must make such an emer-

gency stop, always pull off the road as far

as possible.

The hazard warning lights are turned on

by pushing in the hazard switch. This

causes all turn signal lights to blink. The

hazard warning lights will operate even

though the key is not in the ignition

switch.

OLM049082

The rearview camera will activate when

the back-up light is ON with the ignition

switch ON and the shift lever in the R

(Reverse) position.

To turn the hazard warning lights off,

push the switch a second time.

This system is a supplemental system

that shows behind the vehicle through the

navigation display while backing-up.

4 48

Features of your vehicle

LIGHTING

Battery saver function

Headlight escort function

(if equipped)

CAUTION

• The purpose of this feature is to pre-

vent the battery from being dis-

charged. The system automatically

turns off the parking lights when the

driver removes the ignition key and

opens the driver-side door (in that

order).

• With this feature, the parking lights will

be turned off automatically if the driver

parks on the side of road at night.

If the driver gets out of the vehicle

through other doors (except dri-

ver’s door), the battery saver func-

tion does not operate and the head-

light escort function does not turn

off automatically.Therefore, It caus-

es the battery to be discharged. In

this case, make sure to turn off the

lamp before getting out of the vehi-

cle.

The headlights (and/or taillights) remain

on for approximately 20 minutes after the

ignition key is removed or turned to the

ACC or LOCK position. However, if the

driver’s door is opened and closed, the

headlights are turned off after 30 sec-

onds.

The headlights can be turned off by

pressing the lock button on the transmit-

ter twice or turning off the light switch

from the headlight or Auto light position.

If necessary, to keep the lights on

when the ignition key is removed, per-

form the following:

1) Open the driver-side door.

2) Turn the parking lights OFF and ON

again using the light switch on the

steering column.

4 49

Features of your vehicle

Headlight welcome function

When the headlight switch is in the ON

position or in the AUTO position and all

doors (and tailgate) are closed and

locked, if you press the door unlock but-

ton on the transmitter, the headlight will

come on for about 15 seconds.

If the headlight switch is in the AUTO

position, the function can only operate at

night.

To turn off the headlight immediately, do

one of the following:

• Press the door lock button.

OXM049110

OAM049041

Lighting control

Parking light position (

)

• Press the unlock button twice within 4

seconds.

When the light switch is in the parking

light position (1st position), the tail, posi-

tion, license and instrument panel lights

will turn ON.

The light switch has a Headlight and a

Parking light position.

• Press the unlock button once more

after 4 seconds.

To operate the lights, turn the knob at the

end of the control lever to one of the fol-

lowing positions:

(1) OFF position

(2) Parking light position

(3) Headlight position

(4) Auto light position (if equipped)

4 50

Features of your vehicle

CAUTION

• Never place anything over sensor

(1) located on the instrument

panel. This will ensure better

auto-light system control.

• Don’t clean the sensor using a

window cleaner. The cleaner may

leave a light film which could

interfere with sensor operation.

• If your vehicle has window tint or

other types of metallic coating on

the front windshield, the Auto

light system may not work prop-

erly.

OAM049042

OLM049328

Auto light position (if equipped)

Headlight position (

)

When the light switch is in the AUTO light

position, the taillights and headlights will

be turn ON or OFF automatically

depending on the amount of light outside

the vehicle.

When the light switch is in the headlight

position (2nd position), the head, tail,

position, license and instrument panel

lights will turn ON.

✽

NOTICE

The ignition switch must be in the ON

position to turn on the headlights.

4 51

Features of your vehicle

OAM049044

OAM049043

OAM049045

To flash the headlights, pull the lever

towards you. It will return to the normal

(low beam) position when released. The

headlight switch does not need to be on

to use this flashing feature.

High beam operation

Turn signals and lane change sig-

nals

To turn on the high beam headlights,

push the lever away from you. Pull it back

for low beams.

The ignition switch must be on for the

turn signals to function. To turn on the

turn signals, move the lever up or down

(A). The green arrow indicators on the

instrument panel indicate which turn sig-

nal is operating. They will self-cancel

after a turn is completed. If the indicator

continues to flash after a turn, manually

return the lever to the OFF position.

The high beam indicator will light when

the headlight high beams are switched

on.

To prevent the battery from being dis-

charged, do not leave the lights on for a

prolonged time while the engine is not

running.

4 52

Features of your vehicle

To signal a lane change, move the turn

signal lever slightly and hold it in position

(B). The lever will return to the OFF posi-

tion when released.

If an indicator stays on and does not

flash or if it flashes abnormally, one of the

turn signal bulbs may be burned out and

will require replacement.

One-touch lane change function

(if equipped)

To activate an one-touch lane change

function, move the turn signal lever

slightly for less than 0.5 second and then

release it. The lane change signals will

blink 3 times.

OAM049046

Front fog light (if equipped)

Fog lights are used to provide improved

visibility when visibility is poor due to fog,

rain or snow, etc. The fog lights will turn

on when fog light switch (1) is turned to

ON after the headlights (low beam) are

turned on.

✽

NOTICE

If an indicator flash is abnormally quick

or slow, a bulb may be burned out or

have a poor electrical connection in the

circuit.

To turn off the fog lights, turn the switch

to OFF.

CAUTION

When in operation, the fog lights

consume large amounts of vehicle

electrical power. Only use the fog

lights when visibility is poor.

4 53

Features of your vehicle

WIPERS AND WASHERS

Windshield wiper/washer

A : Wiper speed control

· MIST – Single wipe

· OFF – Off

Rear window wiper/washer

(if equipped)

· INT – Intermittent wipe

· LO – Low wiper speed

· HI – High wiper speed

B : Intermittent wipe time adjustment

C : Wash with brief wipes (front)

D : Rear wiper/washer control

· ON – Continuous wipe

· INT – Intermittent wipe

· OFF – Off

OAM049100N/OAM049048N

E : Wash with brief wipes (rear)

* : if equipped

4 54

Features of your vehicle

✽

NOTICE

If there is heavy accumulation of snow

or ice on the windshield, defrost the

windshield for about 10 minutes, or

until the snow and/or ice is removed

before using the windshield wipers to

ensure proper operation.

✽

NOTICE

• When you operate the wipers, if your

vehicle has a problem in any part of

the wiper operation system, the wiper

may operate in the LO mode regard-

less of the wiper switch position. In

this case, have your vehicle checked

by an authorized HYUNDAI dealer as

soon as possible.

• When the ignition key is removed, the

wiper blade sometimes may move

slightly for reducing the deterioration

of the windshield wipers.

OAM049101N

OAM049102N

Windshield wipers

Windshield washers

Operates as follows when the ignition

switch is turned ON.

In the OFF position, pull the lever gently

toward you to spray washer fluid on the

windshield and to run the wipers 1-3

cycles.

MIST : For a single wiping cycle, move

the lever to this (MIST) position

and release it. The wipers will

operate continuously if the lever is

held in this position.

Use this function when the windshield is

dirty.

The spray and wiper operation will con-

tinue until you release the lever.

OFF : Wiper is not in operation

INT : Wiper operates intermittently at

the same wiping intervals. Use this

mode in a light rain or mist. To vary

the speed setting, turn the speed

control knob(1).

If the washer does not work, check the

washer fluid level. If the fluid level is not

sufficient, you will need to add appropri-

ate non-abrasive windshield washer fluid

to the washer reservoir.

LO : Normal wiper speed

HI : Fast wiper speed

The reservoir filler neck is located in the

front of the engine compartment on the

passenger side.

4 55

Features of your vehicle

CAUTION

To prevent possible damage to the

washer pump, do not operate the

washer when the fluid reservoir is

empty.

WARNING

Do not use the washer in freezing

temperatures without first warming

the windshield with the defrosters;

the washer solution could freeze on

the windshield and obscure your

vision.

OAM049103N

OXM049125

Push the lever away from you to spray

rear washer fluid and to run the rear

wipers 1~3 cycles. The spray and wiper

operation will continue until you release

the lever.

Rear window wiper and washer

switch

The rear window wiper and washer

switch is located at the end of the wiper

and washer switch lever. Turn the switch

to the desired position to operate the rear

wiper and washer.

CAUTION

• To prevent possible damage to

the wipers or windshield, do not

operate the wipers when the

windshield is dry.

ON - Normal wiper operation

INT - Intermittent wiper operation

(if equipped)

• To prevent damage to the wiper

blades, do not use gasoline,

kerosene, paint thinner, or other

solvents on or near them.

OFF - Wiper is not in operation

• To prevent damage to the wiper

arms and other components, do

not attempt to move the wipers

manually.

4 56

Features of your vehicle

INTERIOR LIGHT

CAUTION

Do not use the interior lights for

extended periods when the engine

is not running.

Also, the light (with room lamp)

goes out gradually after approxi-

mately 30 seconds if the door

(except tailgate) is closed.

However, if the ignition switch is

ON or all doors (except tailgate)

are locked, the light will turn off

immediately.

It may cause battery discharge.

If a door (except tailgate) is

opened with the ignition switch in

the ACC or LOCK position, the

light (with room lamp) stays on for

about 20 minutes. However, if a

door (except tailgate) is opened

with the ignition switch in the ON

position, the light (with room

lamp) stays on continuously.

OLM049100K

Map lamp

Push the lens to turn the map lamp on or

off.

• ON

: The light (with room lamp)

stays on at all times.

• OFF : The light (only map lamp) stays

off at all times.

• DOOR: The light (with room lamp)

comes on when any door

(except tailgate) is opened

regardless of the ignition switch

position. When doors (except

tailgate) are unlocked by the

transmitter, the light (with room

lamp) comes on for approxi-

mately 30 seconds as long as

any door (except tailgate) is not

opened.

❈ When the lamp is turned ON

by pressing the lens (1), the

lamp does not turn off even if

the switch (2) is in the OFF

position.

4 57

Features of your vehicle

OLM049101

OLM049103

OLM049102

Room lamp

Luggage lamp (if equipped)

Glove box lamp

The room lamp operates according to the

map lamp main switch position.

The light comes on or off when the tail-

gate is opened or closed.

The glove box lamp comes on when the

glove box is opened.

• ON : The light (room lamp) stays on at

all times regardless of the map

lamp main switch position.

The parking lights or headlights must be

ON for the glove box lamp to function.

4 58

Features of your vehicle

DEFROSTER

CAUTION

To prevent damage to the conduc-

tors bonded to the inside surface of

the rear window, never use sharp

instruments or window cleaners

containing abrasives to clean the

window.

✽

NOTICE

If you want to defrost and defog the

front windshield, refer to “Windshield

defrosting and defogging” in this sec-

tion.

OLM049105

OLM049109

Vanity mirror lamp (if equipped)

Rear window defroster

The defroster heats the window to

remove frost, fog and thin ice from the

rear window, while the engine is running.

•

: The lamp will turn on if this but-

ton is pressed.

•

: The lamp will turn off if this but-

ton is pressed.

✽

NOTICE

Turn off the lamp before return the sun-

visor to its original position.

4 59

Features of your vehicle

To activate the rear window defroster,

press the rear window defroster button

located in the center facia switch panel.

The indicator on the rear window

defroster button illuminates when the

defroster is ON.

If there is heavy accumulation of snow on

the rear window, brush it off before oper-

ating the rear defroster.

The rear window defroster automatically

turns off after approximately 20 minutes

or when the ignition switch is turned off.

To turn off the defroster, press the rear

window defroster button again.

OLM049104

Front windshield deicer

(if equipped)

Outside rearview mirror defroster

(if equipped)

To activate the front windshield deicer,

press the front windshield deicer button

located in the center facia switch panel.

If your vehicle is equipped with the out-

side rearview mirror defrosters, they will

operate at the same time you turn on the

rear window defroster.

The indicator on the front windshield

deicer button illuminates when the deicer

is ON.

The front windshield deicer automatically

turns off after approximately 20 minutes

or when the ignition switch is turned off.

To turn off the deicer, press the front

windshield deicer button again.

4 60

Features of your vehicle

MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)

1. Fan speed control knob

2. Front windshield defroster button

3. MAX A/C mode button

4. Temperature control knob

5. Air conditioning button

6. Mode selection button

7. Air intake control button

OLM049111

4 61

Features of your vehicle

Heating and air conditioning

1. Start the engine.

2. Set the mode to the desired position.

For improving the effectiveness of

heating and cooling;

- Heating:

- Cooling:

3. Set the temperature control to the

desired position.

4. Set the air intake control to the outside

(fresh) air position.

5. Set the fan speed control to the

desired speed.

6. If air conditioning is desired, turn the

air conditioning system on.

OLM049120

4 62

Features of your vehicle

MAX A/C-Level (B, D)

Floor-Level (C, A, D, E)

Air flow is directed toward the upper body

and face.

Most of the air flow is directed to the

floor, with a small amount of the air being

directed to the windshield and side win-

dow defrosters.

In this mode, the air conditioning and the

recirculated air position will be selected

automatically.

Floor/Defrost-Level (A, C, D, E)

Face-Level (B, D)

Most of the air flow is directed to the floor

and the windshield with a small amount

directed to the side window defrosters.

OLM049112

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

Mode selection

The mode selection button controls the

direction of the air flow through the venti-

lation system.

Defrost-Level (A, D)

Air can be directed to the floor, dash-

board outlets, or windshield. Six symbols

are used to represent MAX A/C, Face,

Bi-Level, Floor, Floor-Defrost and Defrost

air position.

Most of the air flow is directed to the

windshield with a small amount of air

directed to the side window defrosters.

Bi-Level (B, D, E, C)

Air flow is directed towards the face and

the floor.

The MAX A/C mode is used to cool the

inside of the vehicle faster.

4 63

Features of your vehicle

OLM049114

OLM049115

OLM049116

Instrument panel vents

Temperature control

Air intake control

This is used to select the outside (fresh)

air position or recirculated air position.

The outlet vents can be opened or closed

separately using the horizontal thumb-

wheel. To close the vent, rotate it left to

the maximum position. To open the vent,

rotate it right to the desired position.

The temperature control knob allows you

to control the temperature of the air flow-

ing from the ventilation system. To

change the air temperature in the pas-

senger compartment, turn the knob to

the right position for warm and hot air or

left position for cooler air.

To change the air intake control position,

push the control button.

Also, you can adjust the direction of air

delivery from these vents using the vent

control lever as shown.

4 64

Features of your vehicle

Recirculated air position

The indicator light on the

✽

NOTICE

WARNING

Prolonged operation of the heater in the

recirculated air position (without air

conditioning selected) may cause fog-

ging of the windshield and side windows

and the air within the passenger com-

partment may become stale.

In addition, prolonged use of the air

conditioning with the recirculated air

position selected will result in excessive-

ly dry air in the passenger compart-

ment.

button illuminates when the

recirculated air position is

selected.

• Continued use of the climate con-

trol system operation in the recir-

culated air position may allow

humidity to increase inside the

vehicle which may fog the glass

and obscure visibility.

With the recirculated air

position selected, air from

the passenger compart-

ment will be drawn through

the heating system and

heated or cooled according

to the function selected.

• Do not sleep in a vehicle with the

air conditioning or heating sys-

tem on. It may cause serious

harm or death due to a drop in the

oxygen level and/or body temper-

ature.

Outside (fresh) air position

• Continued use of the climate con-

trol system operation in the recir-

culated air position can cause

drowsiness or sleepiness, and

loss of vehicle control. Set the air

intake control to the outside

(fresh) air position as much as

possible while driving.

The indicator light on the

button does not illuminates

when the outside (fresh) air

position is selected.

With the outside (fresh) air

position selected, air enters

the vehicle from outside and

is heated or cooled accord-

ing to the function selected.

4 65

Features of your vehicle

System operation

Ventilation

1. Set the mode to the

position.

2. Set the air intake control to the outside

(fresh) air position.

3. Set the temperature control to the

desired position.

4. Set the fan speed control to the

desired speed.

Heating

1. Set the mode to the

OLM049117

OLM049118

position.

Fan speed control

The ignition switch must be in the ON

position for fan operation.

Air conditioning

2. Set the air intake control to the outside

(fresh) air position.

Push the A/C button to turn the air condi-

tioning system on (indicator light will illu-

minate). Push the button again to turn the

air conditioning system off.

3. Set the temperature control to the

desired position.

The fan speed control knob allows you to

control the fan speed of the air flowing

from the ventilation system. To change

the fan speed, turn the knob to the right

for higher speed or left for lower speed.

4. Set the fan speed control to the

desired speed.

5. If dehumidified heating is desired, turn

the air conditioning system on.

• If the windshield fogs up, set the mode

Setting the mode selection knob to the

“0” position turns off the fan.

to the

or

position.

4 66

Features of your vehicle

Operation Tips

Air conditioning

✽

NOTICE

• To keep dust or unpleasant fumes from

entering the car through the ventilation

system, temporarily set the air intake

control to the recirculated air position.

Be sure to return the control to the

fresh air position when the irritation

has passed to keep fresh air in the

vehicle. This will help keep the driver

alert and comfortable.

All HYUNDAI Air Conditioning Systems

are filled with environmentally friendly

R-134a refrigerant which does not dam-

age the ozone layer.

• When using the air conditioning sys-

tem, monitor the engine temperature

gauge closely while driving up hills or

in heavy traffic when outside temper-

atures are high. Air conditioning sys-

tem operation may cause engine over-

heating. Continue to use the blower

fan but turn the air conditioning sys-

tem off if the engine temperature

gauge indicates engine overheating.

• When opening the windows in humid

weather air conditioning may create

water droplets inside the vehicle.

Since excessive water droplets may

cause damage to electrical equipment,

air conditioning should only be oper-

ated with the windows closed.

1. Start the engine. Push the air condi-

tioning button.

2. Set the mode to the

position.

3. Set the air intake control to the outside

air or recirculated air position.

• Air for the heating/cooling system is

drawn in through the grilles just ahead

of the windshield. Care should be

taken that these are not blocked by

leaves, snow, ice or other obstructions.

4. Adjust the fan speed control and tem-

perature control to maintain maximum

comfort.

• When maximum cooling is desired, set

the temperature control to the extreme

left position, set the mode control to

the MAX A/C position, then set the fan

speed control to the highest speed.

• To prevent interior fog on the wind-

shield, set the air intake control to the

fresh air position and fan speed to the

desired position, turn on the air condi-

tioning system, and adjust the temper-

ature control to desired temperature.

4 67

Features of your vehicle

Air conditioning system operation tips

• When using the air conditioning sys-

tem, you may notice clear water drip-

ping (or even puddling) on the ground

under the passenger side of the vehi-

cle. This is a normal system operation

characteristic.

• If the vehicle has been parked in direct

sunlight during hot weather, open the

windows for a short time to let the hot

air inside the vehicle escape.

Outside air

Recirculated

air

• To help reduce moisture inside of the

windows on rainy or humid days,

decrease the humidity inside the vehi-

cle by operating the air conditioning

system.

• Operating the air conditioning system

in the recirculated air position provides

maximum cooling, however, continual

operation in this mode may cause the

air inside the vehicle to become stale.

Blower

Heater core

• During air conditioning system opera-

tion, you may occasionally notice a

slight change in engine speed as the

air conditioning compressor cycles.

This is a normal system operation

characteristic.

Climate control

air filter

Evaporator

core

• During cooling operation, you may

occasionally notice a misty air flow

because of rapid cooling and humid air

intake. This is a normal system opera-

tion characteristics.

1LDA5047

Climate control air filter

The climate control air filter installed

behind the glove box filters the dust or

other pollutants that come into the vehi-

cle from the outside through the heating

and air conditioning system. If dust or

other pollutants accumulate in the filter

over a period of time, the air flow from the

air vents may decrease, resulting in

moisture accumulation on the inside of

the windshield even when the outside

(fresh) air position is selected. If this hap-

pens, have the climate control air filter

replaced by an authorized HYUNDAI

dealer.

• Use the air conditioning system every

month only for a few minutes to ensure

maximum system performance.

4 68

Features of your vehicle

Checking the amount of air con-

ditioner refrigerant and compres-

sor lubricant

✽

NOTICE

• Replace the filter according to the

Maintenance Schedule.

If the car is being driven in severe

conditions such as dusty or rough

roads, more frequent air conditioner

filter inspections and changes are

required.

• When the air flow rate suddenly

decreases, the system should be

checked at an authorized HYUNDAI

dealer.

When the amount of refrigerant is low,

the performance of the air conditioning is

reduced. Overfilling also has a negative

impact on the air conditioning system.

Therefore, if abnormal operation is

found, have the system inspected by an

authorized HYUNDAI dealer.

✽

NOTICE

It is important when servicing the air

conditioning system that the correct

type and amount of oil and refrigerant is

used. Otherwise, damage to the com-

pressor and abnormal system operation

may occur.

WARNING

The air conditioning system should

be serviced by an authorized

HYUNDAI dealer. Improper service

may cause serious injury to the

person performing the service.

4 69

Features of your vehicle

AUTOMATIC CLIMATE CONTROL SYSTEM (IF EQUIPPED)

1. AUTO (automatic control) button

2. Driver’s temperature control knob

3. A/C display

4. Passenger’s temperature control knob

5. Dual temperature control selection button

6. OFF button

7. Front windshield defrost button

8. Air conditioning button

9. Fan speed control button

10. Air intake control button

11. Mode selection button

OLM049121L

4 70

Features of your vehicle

2. Set the temperature switch to the

desired temperature.

If the temperature is set to the lowest

setting (Lo), the air conditioning sys-

tem will operate continuously.

3. To turn the automatic operation off,

select any button or switch of the fol-

lowing:

• Mode selection button

• Air conditioning button

• Front windshield defroster button

• Air intake control button

• Fan speed control switch

OLM049122L

OLM049154

Automatic heating and air condi-

tioning

The automatic climate control system is

controlled by simply setting the desired

temperature.

The Full Automatic Temperature Control

(FATC) system automatically controls the

heating and cooling system as follows;

✽

NOTICE

The selected function will be controlled

manually while other functions operate

automatically.

Never place anything over the sensor

located on the instrument panel to

ensure better control of the heating and

cooling system.

For your convenience and to improve the

effectiveness of the climate control, use

the AUTO button and set the temperature

to 73°F (23°C).

1. Push the AUTO button. It is indicated

by AUTO on the display. The modes,

fan speeds, air intake and air-condi-

tioning will be controlled automatically

by temperature setting.

4 71

Features of your vehicle

Manual heating and air conditioing

The heating and cooling system can be

controlled manually by pushing buttons

or turning knob(s) other than the AUTO

button. In this case, the system works

sequentially according to the order of

buttons or knob(s) selected.

Face-Level (B, D)

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

✽

NOTICE

When pressing any button (or turning

any knob) except the AUTO button

while using automatic operation, the

functions not selected will continue to be

controlled automatically.

Bi-Level (B, D, E, C)

Air flow is directed towards the face and

the floor.

OLM049123

Mode selection

The mode selection button controls the

direction of the air flow through the venti-

lation system.

1. Start the engine.

2. Set the mode to the desired position.

Floor-Level (C, A, D, E)

The air flow outlet port is converted as

follows:

For improving the effectiveness of

heating and cooling;

Most of the air flow is directed to the

floor, with a small amount of the air being

directed to the windshield and side win-

dow defrosters.

- Heating:

- Cooling:

3. Set the temperature control to the

desired position.

Refer to the illustration in the “Manual cli-

mate control system”.

4. Set the air intake control to the outside

(fresh) air position.

Floor/Defrost-Level (A, C, D, E)

Most of the air flow is directed to the floor

and the windshield with a small amount

directed to the side window defrosters.

5. Set the fan speed control to the

desired speed.

6. If air conditioning is desired, turn the

air conditioning system on.

Press the AUTO button in order to convert

to full automatic control of the system.

4 72

Features of your vehicle

OLM049124L

OLM049114

OLM049125L

Defrost-Level (A, D)

Instrument panel vents

Temperature control

Most of the air flow is directed to the

windshield with a small amount of air

directed to the side window defrosters.

The outlet vents can be opened or closed

separately using the horizontal thumb-

wheel. To close the vent, rotate it left to

the maximum position. To open the vent,

rotate it right to the desired position.

The temperature will increase to the

maximum (HI) by turning the knob to the

right extremely.

The temperature will decrease to the min-

imum (Lo) by turning the knob to the left

extremely.

Also, you can adjust the direction of air

delivery from these vents using the vent

control lever as shown.

When turning the knob, the temperature

will increase or decrease by 1°F/0.5°C.

When set to the lowest temperature set-

ting, the air conditioning will operate con-

tinuously.

4 73

Features of your vehicle

Adjusting the driver and passenger side

temperature equally

1. Press the DUAL button again to deac-

tivate DUAL mode. The passenger

side temperature will be set to the

same temperature as the driver side.

2. Operate the driver side temperature

control switch. The driver and passen-

ger side temperature will be adjusted

equally.

Temperature conversion

OLM049126

OLM049127N

You can switch the temperature mode

between Fahrenheit to Centigrade as fol-

lows:

Adjusting the driver and passenger side

temperature individually

Outside thermometer

The current outside temperature is dis-

played in 1°F (1°C) increments. The tem-

perature range is between -40°F ~ 140°F

(-40°C ~ 60°C).

• The outside temperature on the display

may not change immediately.

1. Press the DUAL button to operate the

driver and passenger side temperature

individually. Also, if the passenger side

temperature control switch is operat-

ed, it will automatically change to the

DUAL mode as well.

While pressing the OFF button, press the

AUTO button for 3 seconds or more.

The display will change from Fahrenheit

to Centigrade, or from Centigrade to

Fahrenheit.

If the battery has been discharged or dis-

connected, the temperature mode dis-

play will reset to Fahrenheit.

2. Operate the left temperature control to

adjust the driver side temperature.

Operate the right temperature control

to adjust the passenger side tempera-

ture.

When the driver side temperature is set

to the highest (HI) or lowest (Lo) temper-

ature setting, the DUAL mode is deacti-

vated for maximum heating or cooling.

4 74

Features of your vehicle

Recirculated air position

With the recirculated air

WARNING

position selected, air from

the passenger compart-

ment will be drawn through

the heating system and

heated or cooled according

to the function selected.

• Continued use of the climate con-

trol system operation in the recir-

culated air position may allow

humidity to increase inside the

vehicle which may fog the glass

and obscure visibility.

• Do not sleep in a vehicle with the

air conditioning or heating system

on. It may cause serious harm or

death due to a drop in the oxygen

level and/or body temperature.

Outside (fresh) air position

With the outside (fresh) air

position selected, air enters

the vehicle from outside

and is heated or cooled

according to the function

selected.

OLM049128L

Air intake control

This is used to select the outside (fresh)

air position or recirculated air position.

• Continued use of the climate con-

trol system operation in the recir-

culated air position can cause

drowsiness or sleepiness, and loss

of vehicle control. Set the air intake

control to the outside (fresh) air

position as much as possible while

driving.

To change the air intake control position,

push the control button.

✽

NOTICE

Prolonged operation of the heater in the

recirculated air position (without air

conditioning selected) may cause fog-

ging of the windshield and side windows

and the air within the passenger com-

partment may become stale.

In addition, prolonged use of the air con-

ditioning with the recirculated air posi-

tion selected will result in excessively dry

air in the passenger compartment.

4 75

Features of your vehicle

OLM049129L

OLM049130L

OLM049131

Fan speed control

Air conditioning

OFF mode

The fan speed can be set to the desired

speed by operating the fan speed control

switch.

Press the A/C button to turn the air con-

ditioning system on (indicator light will

illuminate).

Press the OFF button to turn off the air

climate control system. However, you can

still operate the mode and air intake but-

tons as long as the ignition switch is in

the ON position.

To change the fan speed, press ( ꢀ)

the switch for higher speed, or press

(⊳ ) the switch for lower speed. To

turn the fan speed control off, press the

front blower OFF button.

Press the button again to turn the air

conditioning system off.

4 76

Features of your vehicle

WINDSHIELD DEFROSTING AND DEFOGGING

• For maximum defrosting, set the tem-

perature control to the extreme

right/hot position and the fan speed

control to the highest speed.

WARNING - Windshield

heating

Do not use the

or

position

• If warm air to the floor is desired while

defrosting or defogging, set the mode

to the floor-defrost position.

during cooling operation in

extremely humid weather. The dif-

ference between the temperature of

the outside air and the windshield

could cause the outer surface of

the windshield to fog up, causing

loss of visibility. In this case, set

• Before driving, clear all snow and ice

from the windshield, rear window, out-

side rear view mirrors, and all side win-

dows.

the mode selection to the

tion and fan speed control to the

lower speed.

posi-

• Clear all snow and ice from the hood

and air inlet in the cowl grill to improve

heater and defroster efficiency and to

reduce the probability of fogging up the

inside of the windshield.

OLM049132

Manual climate control system

To defog inside windshield

1. Set the fan speed to the desired posi-

tion.

2. Select desired temperature.

3. Press the defrost button (

4. The outside (fresh) air will be selected

automatically. If the position is

).

selected, air conditioning will also be

selected automatically.

If the air conditioning and/or outside

(fresh) air position are not selected auto-

matically, press the corresponding button

manually.

4 77

Features of your vehicle

OLM049133

OLM049134

Automatic climate control system

To defog inside windshield

OLM049135

To defrost outside windshield

1. Set the fan speed to the highest posi-

tion.

To defrost outside windshield

1. Set the fan speed to the highest posi-

tion.

1. Set the fan speed to the desired posi-

tion.

2. Select desired temperature.

2. Set the temperature to the extreme hot

position.

2. Set the temperature to the extreme hot

(HI) position.

3. Press the defrost button (

).

3. Press the defroster button (

).

3. Press the defroster button (

).

4. The outside (fresh) air and air condi-

tioning will be selected automatically.

4. The air conditioning will turn on

according to the detected ambient

temperature and outside (fresh) air

position will be selected automatically.

4. The air conditioning will turn on

according to the detected ambient tem-

perature and outside (fresh) air posi-

tion will be selected automatically.

If the air conditioning and outside (fresh)

air position are not selected automatical-

ly, adjust the corresponding button man-

ually. If the

position is selected,

lower fan speed is adjusted to a higher

fan speed.

4 78

Features of your vehicle

Defogging logic

To reduce the possibility of fogging up

the inside of the windshield, the air intake

or air conditioning are controlled auto-

matically according to certain conditions

such as

or

position.To cancel or

return to the defogging logic, perform the

following steps:

OLM049136N

OLM049137N

Manual climate control system

Automatic climate control system

1. Turn the ignition switch to the ON posi-

tion.

2. Select the defrost position pressing

1. Turn the ignition switch to the ON posi-

tion.

2. Select the defroster position pressing

the defrost button (

).

the defroster button (

).

3. Press the air intake control button at

least 5 times within 3 seconds.

3. While pressing the air conditioning

button (A/C), press the air intake con-

trol button at least 5 times within 3 sec-

onds.

The indicator light in the air intake control

button will blink 3 times with 0.5 second

of interval. It indicates that the defogging

logic is canceled or returned to the pro-

grammed status.

The A/C display blinks 3 times with 0.5

second of interval. It indicates that the

defogging logic is canceled or returned to

the programmed status.

If the battery has been discharged or dis-

connected, the system resets to the pre-

programmed defogging logic.

If the battery has been discharged or dis-

connected, the system resets to the pre-

programmed defogging logic.

4 79

Features of your vehicle

STORAGE COMPARTMENT

These compartments can be used to

store small items required by the driver

or passengers.

CAUTION

• To avoid possible theft, do not

leave valuables in the storage

compartment.

UNLOCK

• Always keep the storage com-

partment covers closed while

driving. Do not attempt to place

so many items in the storage

compartment that the storage

compartment cover cannot close

securely.

LOCK

OLM049151

OLM049152

Center console storage

Glove box

These compartments can be used to

store small items required by the driver

or front passenger.

The glove box can be locked and

unlocked with a master key.

To open the glove box, pull the handle

and the glove box will automatically

open. Close the glove box after use.

To open the center console storage pull

up the lever.

WARNING - Flammable

materials

Do not store cigarette lighters,

propane cylinders, or other flamma-

ble/explosive materials in the vehi-

cle. These items may catch fire

and/or explode if the vehicle is

exposed to hot temperatures for

extended periods.

WARNING

To reduce the risk of injury in an

accident or sudden stop, always

keep the glove box door closed

while driving.

4 80

Features of your vehicle

WARNING

• Do not keep objects except sun-

glass inside the sunglass holder.

Such objects can be thrown from

the holder in the event of a sud-

den stop or an accident, possibly

injuring the passengers in the

vehicle.

• Do not open the sunglass holder

while the vehicle is moving. The

rear view mirror of the vehicle

can be blocked by an open sun-

glass holder.

OLM049142

Sunglass holder

To open the sunglass holder, press the

cover and the holder will slowly open.

Place your sunglasses in the compart-

ment door with the lenses facing out.

Push to close.

4 81

Features of your vehicle

INTERIOR FEATURES

WARNING

• Do not hold the lighter in after it

is already heated because it will

overheat.

• If the lighter does not pop out

within 30 seconds, remove it to

prevent overheating.

CAUTION

OLM049144

OLM049145

Only a genuine HYUNDAI lighter

should be used in the cigarette

lighter socket. The use of plug-in

accessories (shavers, hand-held

vacuums, and coffee pots, etc.) may

damage the socket or cause electri-

cal failure.

Cigarette lighter (if equipped)

Ashtray (if equipped)

To use the ashtray, open the cover.

To clean or empty the ashtray, pull it out.

For the cigarette lighter to work, the igni-

tion switch must be in the ACC position

or the ON position.

To use the cigarette lighter, push it all the

way into its socket. When the element

has heated, the lighter will pop out to the

“ready” position.

WARNING - Ashtray use

• Do not use the vehicle’s ashtrays

as waste receptacles.

• Putting lit cigarettes or matches

in an ashtray with other com-

bustible materials may cause a

fire.

Do not hold the cigarette lighter pressed

in. This can damage the heating element

and create a fire hazard.

If it is necessary to replace the cigarette

lighter, use only a genuine HYUNDAI

replacement or its approved equivalent.

4 82

Features of your vehicle

■ Front

Cup holder

WARNING - Hot liquids

• Do not place uncovered cups of

hot liquid in the cup holder while

the vehicle is in motion. If the hot

liquid spills, you burn yourself.

Such a burn to the driver could

lead to loss of control of the vehi-

cle.

OLM049146

• To reduce the risk of personal

injury in the event of sudden stop

or collision, do not place uncov-

ered or unsecured bottles, glass-

es, cans, etc., in the cup holder

while the vehicle is in motion.

■ Rear (if equipped)

OLM049207

Sunvisor

Use the sunvisor to shield direct light

through the front or side windows.

To use the sunvisor, pull it downward.

To use the sunvisor for the side window,

pull it downward, unsnap it from the

bracket (1) and swing it to the side (2).

Adjust the sunvisor extension forward or

backward (3).

OLM049147

To use the vanity mirror, pull down the

visor and slide the mirror cover (4).

Cups or small beverage cans may be

placed in the cup holders.

The ticket holder (5) is provided for hold-

ing a tollgate ticket. (if equipped)

4 83

Features of your vehicle

■ Front

CAUTION - Vanity mirror

lamp (if equipped)

If you use the vanity mirror lamp,

turn off the lamp before return the

sunvisor to its original position. It

could result in battery discharge

and possible sunvisor damage.

CAUTION

• Use the power outlet only when

the engine is running and remove

the accessory plug after use.

Using the accessory plug for pro-

longed periods of time with the

engine off could cause the bat-

tery to discharge.

• Only use 12V electric accessories

which are less than 10A in elec-

tric capacity.

OLM049150

■ Rear (if equipped)

• Adjust the air-conditioner or

heater to the lowest operating

level when using the power outlet.

• Close the cover when not in use.

• Some electronic devices can

cause electronic interference

when plugged into a vehicle’s

power outlet. These devices may

cause excessive audio static and

malfunctions in other electronic

systems or devices used in your

vehicle.

OLM049153

Power outlet

The power outlet is designed to provide

power for mobile telephones or other

devices designed to operate with vehicle

electrical systems. The devices should

draw less than 10 amps with the engine

running.

WARNING

Do not put a finger or a foreign ele-

ment (pin, etc.) into a power outlet

and do not touch with a wet hand.

You may get an electric shock.

4 84

Features of your vehicle

Setup the clock

With audio off

■ Type A

■ Type B

1. Press the [SETUP] button until the

clock of the display blinks.

2. Set the clock by turning the knob(1)

and press it.

With audio on

1. Press the [SETUP] button.

2. Select the [CLOCK] mode by turning

the knob(1) and press it.

3. Set the clock by turning the knob(1)

and press it.

OLM049208

OXM049228

Digital clock (if equipped)

WARNING

Floor mat anchor(s) (if equipped)

When using a floor mat on the front floor

carpet, make sure it attaches to the floor

mat anchor(s) in your vehicle. This keeps

the floor mat from sliding forward.

Do not adjust the clock while driv-

ing. You may lose your steering

control and cause severe personal

injury or accidents.

Whenever the battery terminals or relat-

ed fuses are disconnected, you must

reset the time.

When the ignition switch is in the ACC or

ON position, the clock buttons operate as

follows:

4 85

Features of your vehicle

If necessary, contact your authorized

HYUNDAI dealer to obtain a luggage net.

WARNING

The following must be observed

when installing ANY floor mat to

the vehicle.

CAUTION

To prevent damage to the goods or

the vehicle, care should be taken

when carrying fragile or bulky

objects in the luggage compart-

ment.

• Ensure that the floor mats are

securely attached to the vehicle's

floor mat anchor(s) before driving

the vehicle.

• Do not use ANY floor mat that

cannot be firmly attached to the

vehicle's floor mat anchors.

OLM049202

WARNING

• Do not stack floor mats on top of

one another (e.g. all-weather rub-

ber mat on top of a carpeted floor

mat). Only a single floor mat

should be installed in each posi-

tion.

Avoid eye injury. DO NOT over-

stretch the luggage net, ALWAYS

keep your face and body out of the

luggage net’s recoil path. DO NOT

use the luggage net when the strap

has visible signs of wear or dam-

age.

Luggage net (holder)

(if equipped)

To keep items from shifting in the cargo

area, you can use the holders located in

the cargo area to attach the luggage net.

IMPORTANT -Your vehicle was man-

ufactured with driver's side floor

mat anchors that are designed to

securely hold the floor mat in

place. To avoid any interference

with pedal operation, HYUNDAI

recommends that only the

HYUNDAI floor mat designed for

use in your vehicle be installed.

It can be mounted as a flat net by using

holders (1) and (2), or as an envelop net

by using holders (2) and (3).

4 86

Features of your vehicle

OLM049203

OLM049204

OLM049205

To use the cargo security screen, pull the

handle backward and insert the edges

into the slots.

When not in use, place the cargo securi-

ty screen on the lower portion of the

cargo area.

Cargo security screen

(if equipped)

Use the cargo security screen to hide

items stored in the cargo area.

4 87

Features of your vehicle

EXTERIOR FEATURES

CAUTION

WARNING

• When carrying cargo on the roof

rack, take the necessary precau-

tions to make sure the cargo does

not damage the roof of the vehicle.

• Do not place objects on the cargo

security screen. Such objects

may be thrown about inside the

vehicle and possibly injure vehi-

cle occupants during an accident

or when braking.

• When carrying large objects on

the roof rack, make sure they do

not exceed the overall roof length

or width.

• Never allow anyone to ride in the

luggage compartment. It is

designed for luggage only.

• When you are carrying cargo on

the roof rack, do not operate the

sunroof (if equipped).

• Maintain the balance of the vehi-

cle and locate the weight as far

forward as possible.

OLM049206

Roof rack (if equipped)

If the vehicle has a roof rack, you can

load cargo on top of your vehicle.

WARNING

CAUTION

• The following specification is the

maximum weight that can be

loaded onto the roof rack.

Distribute the load as evenly as

possible onto roof rack and

secure the load firmly.

✽

NOTICE

Since the cargo security screen

may be damaged or malformed, do

not put the luggage on it when it is

used.

If the vehicle is equipped with a

panoramic sunroof, it is not recom-

mended that an aftermarket roof rack

be installed.

ROOF

RACK

220 lbs. (100 kg)

EVENLY DISTRIBUTED

Loading cargo or luggage in

excess of the specified weight

limit on the roof rack may dam-

age your vehicle.

(Continued)

4 88

Features of your vehicle

AUDIO SYSTEM

✽

NOTICE

(Continued)

CAUTION

If you install an aftermarket HID head-

lamp, your vehicle's audio and electron-

ic device may malfunction.

• The vehicle center of gravity will

be higher when items are loaded

onto the roof rack. Avoid sudden

starts, braking, sharp turns,

abrupt maneuvers or high speeds

that may result in loss of vehicle

control or rollover resulting in an

accident.

• Before entering a place with a low

height clearance or a car wash,

remove the antenna by rotating it

counterclockwise. If not, the

antenna may be damaged.

■ Type A

■ Type B

• When reinstalling your antenna, it

is important that it is fully tight-

ened and adjusted to the upright

position to ensure proper recep-

tion. But it could be removed

when parking the vehicle or when

loading cargo on the roof rack.

• Always drive slowly and turn cor-

ners carefully when carrying

items on the roof rack. Severe

wind updrafts, caused by passing

vehicles or natural causes, can

cause sudden upward pressure

on items loaded on the roof rack.

This is especially true when car-

rying large, flat items such as

wood panels or mattresses. This

could cause the items to fall off

the roof rack and cause damage

to your vehicle or others around

you.

• When cargo is loaded on the roof

rack, do not place the cargo near

the antenna pole to ensure proper

reception.

OHM048154

Antenna

Roof antenna

Your vehicle uses a roof antenna to

receive both AM and FM broadcast sig-

nals. This antenna is removable. To

remove the antenna, turn it counterclock-

wise. To install the antenna, turn it clock-

wise.

• To prevent damage or loss of

cargo while driving, check fre-

quently before or while driving to

make sure the items on the roof

rack are securely fastened.

4 89

Features of your vehicle

CD/USB/iPod mode

It will function as TRACK UP/DOWN

button.

MODE (1)

Press the button to change audio source.

- FM(1~2)➟AM➟SAT(1~3)➟CD➟USB

AUX(iPod) FM...

VOLUME (VOL

/

) (3)

1

2

• Push the lever upward ( ) to increase

the volume.

SEEK/PRESET (

/

) (2)

The SEEK/PRESET button has different

functions based on the system mode.

3

• Push the lever downward ( ) to decrease

the volume.

4

For the following functions the button

should be pressed for 0.8 second or

more.

MUTE (4)

• Press the button to mute the sound

Steering wheel audio control

(if equipped)

RADIO mode

It will function as the AUTO SEEK select

button.

• Press the button to turn off the micro-

phone during a telephone call.

The steering wheel may incorporate

audio control buttons. These buttons are

installed to promote safe driving.

Detailed information for audio control

buttons are described in the following

pages in this section.

CD/USB/iPod mode

It will function as the FF/REW button.

CAUTION

Do not operate audio remote con-

trol buttons simultaneously.

If the SEEK/PRESET button is pressed

for less than 0.8 second, it will work as

follows in each mode.

RADIO mode

It will function as the PRESET STATION

buttons.

4 90

Features of your vehicle

FM reception

AM reception

OLM049195

JBM001

JBM002

AM broadcasts can be received at

greater distances than FM broadcasts.

This is because AM radio waves are

transmitted at low frequencies. These

long, low frequency radio waves can fol-

low the curvature of the earth rather than

travelling straight out into the atmos-

phere. In addition, they curve around

obstructions so that they can provide bet-

ter signal coverage.

How vehicle audio works

Aux, USB and iPod port

(if equipped)

AM and FM radio signals are broadcast

from transmitter towers located around

your city. They are intercepted by the

radio antenna on your vehicle.This signal

is then received by the radio and sent to

your vehicle speakers.

If your vehicle has an aux and/or

USB(universal serial bus) port or iPod

port, you can use an aux port to connect

audio devices and the USB port to plug

in a USB device.

When a strong radio signal has reached

your vehicle, the precise engineering of

your audio system ensures the best pos-

sible quality reproduction. However, in

some cases the signal coming to your

vehicle may not be strong and clear. This

can be due to factors such as the dis-

tance from the radio station, closeness of

other strong radio stations or the pres-

ence of buildings, bridges or other large

obstructions in the area.

Both ports are used together with the

accessory iPod cable to connect an iPod.

✽

NOTICE

When using a portable audio device

connected to the power outlet, noise may

occur during playback. If this happens,

use the power source of the portable

audio device.

❈ iPod^®is a trademark of Apple Inc.

4 91

Features of your vehicle

FM radio station

JBM003

JBM004

JBM005

FM broadcasts are transmitted at high

frequencies and do not bend to follow the

earth's surface. Because of this, FM

broadcasts generally begin to fade at

short distances from the station.

• Fading - As your vehicle moves away

from the radio station, the signal will

weaken and sound will begin to fade.

When this occurs, we suggest that you

select another stronger station.

• Station Swapping - As a FM signal

weakens, another more powerful sig-

nal near the same frequency may

begin to play. This is because your

radio is designed to lock onto the clear-

est signal. If this occurs, select another

station with a stronger signal.

Also, FM signals are easily affected by

buildings, mountains, or other obstruc-

tions.These can result in certain listening

conditions which might lead you to

believe a problem exists with your radio.

The following conditions are normal and

do not indicate radio trouble:

• Flutter/Static - Weak FM signals or

large obstructions between the trans-

mitter and your radio can disturb the

signal causing static or fluttering nois-

es to occur. Reducing the treble level

may lessen this effect until the distur-

bance clears.

• Multi-Path Cancellation - Radio signals

being received from several directions

can cause distortion or fluttering. This

can be caused by a direct and reflect-

ed signal from the same station, or by

signals from two stations with close

frequencies. If this occurs, select

another station until the condition has

passed.

4 92

Features of your vehicle

• If you are driving on a mountain road

where is blocked by mountains.

Satellite radio reception

You may experience receiving difficulties

receiving XM™ satellite radio signals in

the following situations.

• If you are driving in an area with tall

trees that block the signal(10m or

more), for example on an road that

goes through a dense forest.

• If you are driving in a tunnel or a cov-

ered parking area.

• The signal can become weak in some

areas that are not covered by the XM™

repeater network.

• If you are driving beneath the top level

of a multi-level freeway.

• If you drive under a bridge.

• If you are driving next to a tall vehi-

cle(such as a truck or a bus) that block

the signal.

NOTE:

There may be other unforeseen cir-

cumstances leading to reception

problems with XM™ satellite radio

signal.

• If you are driving in a valley where the

surrounding hills or peaks block the

signal from the satellite.

4 93

Features of your vehicle

Using a cellular phone or a two-way

radio

• Keep CDs in their cases after use to

protect them from scratches or dirt.

Care of discs

• If the temperature inside the vehicle is

too high, open the vehicle windows for

ventilation before using your vehicle

audio.

When a cellular phone is used inside the

vehicle, noise may be produced from the

audio equipment. This does not mean

that something is wrong with the audio

equipment. In such a case, use the cellu-

lar phone at a place as far as possible

from the audio equipment.

• Depending on the type of CD-R/CD-

RW CDs, certain CDs may not operate

normally according to manufacturing

companies or making and recording

methods. In such circumstances, if you

still continue to use those CDs, they

may cause the malfunction of your

vehicle audio system.

• It is illegal to copy and use MP3/WMA

files without permission. Use CDs that

are created only by lawful means.

• Do not apply volatile agents such as

benzene and thinner, normal cleaners

and magnetic sprays made for ana-

logue disc onto CDs.

WARNING

✽

NOTICE - Playing an

Do not use a cellular phone while

driving. Stop at a safe location to

use a cellular phone.

Incompatible Copy

Protected Audio CD

• To prevent the disc surface from get-

ting damaged. Hold and carry CDs by

the edges or the edges of the center

hole only.

Some copy protected CDs, which do not

comply with the international audio CD

standards (Red Book), may not play on

your vehicle audio. Please note that if

you try to play copy protected CDs and

the CD player does not perform correct-

ly the CDs maybe defective, not the CD

player.

• Clean the disc surface with a piece of

soft cloth before playback (wipe it from

the center to the outside edge).

• Do not damage the disc surface or

attach pieces of sticky tape or paper

onto it.

• Make sure objects other than CDs are

not inserted into the CD player (Do not

insert more than one CD at a time).

4 94

Features of your vehicle

RADIO, SET UP, VOLUME, AUDIO CONTROL (USA/CANADA)

1. AM Selection Button

2. FM Selection Button

3. Automatic Station Seek Button

4. Power ON/OFF Button and Volume

Control Knob

5. Preset Selection Button

6. SCAN Selection Button

7. DISP Button

8. SETUP Button

9. TUNE & AUDIO Control Knob

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 95

Features of your vehicle

Using RADIO, SETUP, VOLUME

and AUDIO CONTROL

5. Preset Selection Button

8. SETUP Button

• Press [1]~[6] buttons less than 0.8 sec-

ond to play the station saved in each

button.

Press this Button to enter SETUP mode,

If no action is taken for 8 seconds, it will

return to previous mode.

1. AM Selection Button

Pressing the [AM] button selects the AM

band. AM Mode is displayed on the LCD.

• Press [1]~[6] button more than 0.8 sec-

ond or longer to save the current station

to the respective button with a beep.

In “SETUP” mode, rotate the TUNE knob

to move the cursor between items, and

push the TUNE knob to select.

2. FM Selection Button

Turns to FM mode and toggles FM1 and

FM2 when the button is pressed each

time.

6. SCAN Button

• SCROLL

Select whether long file names are

scrolled continuously (“ON”) or just once

(“OFF”).

• When the button is pressed, it auto-

matically scans the radio stations

upwards.

3. Automatic Station Seek Button

• The SCAN feature steps through each

station, starting from the initial station,

for ten seconds.

• SDVC

• When the [SEEK

] is pressed, it will

Select this item to turn the SDVC(Speed

Dependent Volume Control) feature ON

or OFF. If it is turned ON, volume level is

adjusted automatically according to the

vehicle speed.

automatically tune to the next lower

station.

• Press the [SCAN] button again to stop

the scan feature and to listen to the

currently selected channel.

• When the [SEEK

] is pressed, it will

automatically tune to the next higher

station.

7. DISP Button

• P.BASS (PowerBass)

Turn the LCD Display & Backlight on/off

when [DISP] button press.

4. Power ON/OFF Button & Volume

Control Knob

This function creates virtual sound

effects and allows adjustments to the

BASS level.

• Turns the audio system on/off when

the ignition switch is on ACC or ON.

HIGH ➟ MID ➟ LOW ➟ OFF

• If the knob is turned clockwise/counter-

clockwise, the volume will increase

/decrease.

• XM

Select default display of XM mode.

“Category/Channel name” or “Artist/Song

Title” can be selected.

4 96

Features of your vehicle

• PHONE (if available)

• FADER Control

9. TUNE Knob & Audio Control

Knob

Select this item to enter BLUETOOTH^®

setup mode. Refer to “BLUETOOTH

PHONE OPERATION” section for

detailed information.

Turn the control knob clockwise to

emphasize rear speaker sound (front

speaker sound will be attenuated). When

the control knob is turned counterclock-

wise, front speaker sound will be empha-

sized (rear speaker sound will be attenu-

ated).

• Rotate the knob clockwise or counter-

clock wise to increase or decrease from

current frequency.

(AM 10kHz, FM 200kHz)

• Adjusting the Clock

Press the [SETUP] button. Use the vol-

ume controller to adjust the clock in the

following order: CLOCK ENTER hour or

minute.

Pressing the button changes the BASS,

MIDDLE, TREBLE, FADER and BAL-

ANCE TUNE mode. The mode selected

is shown on the display. After selecting

each mode, rotate the Audio control knob

clockwise or counterclockwise.

•

• BALANCE Control

Rotate the knob clockwise to emphasize

Adjust the hour and press the [ENTER]

button to set. Use the same method to

right speaker sound (left speaker sound

will be attenuated). When the control

knob is turned counter clockwise, left

speaker sound will be emphasized (right

speaker sound will be attenuated).

adjust the minute and press the [ENTER]

button to complete and exit from clock

adjustment mode.

• BASS Control

To increase the BASS, rotate the knob

clockwise, while to decrease the BASS,

rotate the knob counterclockwise.

Pressing the [SETUP] button while in

POWER OFF screen will allow the user

to make immediately adjustments to the

clock.

• MIDDLE Control

To increase the MIDDLE, rotate the knob

clockwise, while to decrease the MID-

DLE, rotate the knob counterclockwise.

• TREBLE Control

To increase the TREBLE, rotate the knob

clockwise, while to decrease the TRE-

BLE, rotate the knob counterclockwise.

4 97

Features of your vehicle

CD (USA/CANADA)

1. CD Loading Slot

2. CD Eject Button

3. CD Selection Button

4. Automatic Station Seek Button

5. RANDOM play Button

6. REPEAT Button

7. CD Indicator

8. SCAN Play Button

9. INFO Button

10. FOLDER Moving Button

11. SEARCH Knob & ENTER Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 98

Features of your vehicle

If there is no CD, then the message "No

CD" will become displayed on the LCD

for 3 seconds and returns to the previous

mode.

• To cancel RANDOM Play, press this

button again.

Using CD Player

1. CD Loading Slot

6. REPEAT Button

Insert a CD label side up and gently push

in while ignition switch is on ACC or ON.

The audio automatically switches to CD

mode and begins to play the CD. If the

audio was turned off, audio power will

automatically turned on as the CD is

inserted.

• Press this button for less than 0.8 sec-

onds to repeat current song.

4. Track Selection Button

• Press [TRACK

] button for less than

0.8 seconds to play from the beginning

of current song.

• Press this button for 0.8 seconds or

longer to repeat all songs in current

folder.

• Press [TRACK

] button for less than

• To cancel REPEAT, press this button

again.

0.8 seconds and press again within 1

seconds to play the previous song.

- This audio only recognizes 12cm-size, CD-

DA(Audio CD) or ISO data-CD (MP3 CD).

• Press [TRACK

] button for 0.8 sec-

- If UDF data-CD or non-CD(e.g. DVD) is

inserted, "Reading Error" message will

be displayed and the disc will be ejected.

7. CD Indicator

onds or longer to initiate reverse direc-

tion high speed sound search of cur-

rent song.

When car ignition switch is ACC or ON

and if the CD is loaded, this indicator is

lit. If the CD is ejected, the light is turned

off.

• Press [TRACK

0.8 seconds to play the next song.

• Press [TRACK ] button for 0.8 sec-

onds or longer to initiate forward direc-

tion high speed sound search of cur-

rent song.

] button for less than

CAUTION

Do not insert a CD if CD indicator is

lit.

8. SCAN Play Button

Play each song in the CD for 10 seconds.

To cancel SCAN Play, press this button

again.

2. CD Eject Button

• Press [ ] button to eject the CD. This

button works regardless of ignition

switch status.

5. RANDOM Play Button

9. INFO Button

• Press this button for less than 0.8 sec-

onds to play songs randomly in current

folder.

Displaces the information of the current

song.

3. CD Selection Button

• Press this button for 0.8 seconds or

longer to play songs randomly in entire

CD.

- Audio CD : Disc Title/Artist, Track Title

/Artist, Total Tracks.

If there is a CD in the CD DECK it switch-

es to CD mode.

4 99

Features of your vehicle

- MP3 CD : File Name, Title, Artist,

Album, Folder, Total Files (Not displayed

if the information is unavailable on the

CD or file.)

2. Folder playing order :

NOTE:

Order of playing files(folders) :

10. FOLDER Moving Button

• Press [FOLDER

] button to move to

child folder of the current folder and

display the first song in the folder.

❋ If no song file is contained in the

folder, that folder is not displayed.

Press TUNE/ ENTER knob to move to

the folder displayed. It will play the first

song in the folder.

• Press [FOLDER

] button to move to

parent folder of the current folder and

display the first song in the folder.

Press TUNE/ENTER knob to move to

the folder displayed.

11. SEARCH Knob & ENTER

Button

• Turn this knob clockwise to browse

songs after current song, or counter-

clockwise to browse songs before cur-

rent song. To play the displayed song,

press the knob.

1. Song playing order : to sequen-

tially.

• Pressing this knob without turning

enters to AUDIO CONTROL mode.

4 100

Features of your vehicle

(Continued)

• An encrypted MP3 PLAYER is not

recognizable.

(Continued)

CAUTION IN USING

USB DEVICE

• To use an external USB device,

make sure the device is not con-

nected when starting up the vehi-

cle. Connect the device after

starting up.

• If you disconnect the external USB

device during playback in USB

mode, the external USB device can

be damaged or may malfunction.

Therefore, disconnect the external

USB device when the audio is

turned off or in another mode. (e.g,

Radio, XM or CD)

• Depending on the condition of

the external USB device, the con-

nected external USB device can

be unrecognizable.

• When the formatted byte/sector

setting of External USB device is

not either 512BYTE or 2048BYTE,

then the device will not be recog-

nized.

• If you start the engine when the

USB device is connected, it may

damage the USB device. (USB

flashdrives are very sensitive to

electric shock.)

• Depending on the type and

capacity of the external USB

device or the type of the files

stored in the device, there is a dif-

ference in the time taken for

recognition of the device.

• Use only a USB device formatted

to FAT 12/16/32.

• If the engine is started up or

turned off while the external USB

device is connected, the external

USB device may not work.

• USB devices without USB I/F

authentication may not be recog-

nizable.

• Do not use the USB device for

purposes other than playing

music files.

• It may not play inauthentic MP3 or

WMA files.

1) It can only play MP3 files with the

• Make sure the USB connection

terminal does not come in con-

tact with the human body or other

objects.

• Use of USB accessories such as

rechargers or heaters using USB

I/F may lower performance or

cause trouble.

compression

8Kbps~320Kbps.

rate

between

• If you repeatedly connect or dis-

connect the USB device in a short

period of time, it may break the

device.

2) It can only play WMA music files

with the compression rate

between 8Kbps~320Kbps.

• If you use devices such as a USB

hub purchased separately, the

vehicle’s audio system may not

recognize the USB device. In that

case, connect the USB device

directly to the multimedia termi-

nal of the vehicle.

• Take precautions for static elec-

tricity when connecting or dis-

connecting the external USB

device.

• You may hear a strange noise

when connecting or disconnect-

ing a USB device.

(Continued)

4 101

Features of your vehicle

(Continued)

• If the USB device is divided by

logical drives, only the music files

on the highest-priority drive are

recognized by car audio.

• Please avoid using USB memory

products which can be used as

key chains or cellular phone

accessories as they could cause

damage to the USB jack. Please

make certain only to use plug

type connector products as

shown below.

• Devices such as MP3 Player/

Cellular phone/Digital camera can

be unrecognizable by standard

USB I/F can be unrecognizable.

• Some non-standard USB devices

(METAL COVER TYPE USB) can

be unrecognizable.

• Some USB flash memory readers

(such as CF, SD, microSD, etc.) or

external-HDD type devices can be

unrecognizable.

• Music files protected by DRM

(DIGITAL RIGHTS MANAGE-

MENT) are not recognizable.

• The data in the USB memory may

be lost while using this audio.

Always back up important data on

a personal storage device.

(Continued)

4 102

Features of your vehicle

AUX/USB (USA/CANADA)

1. AUX/USB Selection Button

2. TRACK Selection Button

3. RANDOM Playback Button

4. REPEAT Selection Button

5. SCAN Selection Button

6. INFO Button

7. FOLDER Moving Button

8. SEARCH Knob & ENTER Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 103

Features of your vehicle

➟ TITLE ➟ ARTIST ➟ ALBUM ➟ FOLDER

➟ TOTAL FILE ➟ NORMAL DISPLAY ➟

FILE NAME ➟… (Displays no informa-

tion if the file has no song information.)

3. RANDOM Playback Button

Using USB device

• Press this button for less than 0.8 sec-

onds to play songs randomly in current

folder.

1. AUX/USB Selection Button

If the auxiliary device is connected, it

switches to AUX or USB mode to play the

sound from the auxiliary player.

• Press this button for 0.8 seconds or

longer to play songs randomly in entire

USB device.

7. FOLDER Moving Button

• Press [FOLDER

] button to move to

If there is no auxiliary device, then the

message "No Media" will become dis-

played on the LCD for 3 seconds and

returns to previous mode.

• To cancel RANDOM play, press this

button again.

child folder of the current folder and

display the first song in the folder.

Press TUNE/ ENTER knob to move to

the folder displayed. It will play the first

song in the folder.

4. REPEAT Button

2. TRACK Selection Button

• Press this button for less than 0.8 sec-

onds to repeat current song.

• Press [FOLDER

] button to move to

• Press the [TRACK

] button for less

parent folder display the first song in

the folder.

• Press this button for 0.8 seconds or

longer to repeat all songs in current

folder.

than 0.8 seconds to play from the

beginning of the current song.

Press TUNE/ENTER knob to move to

the folder displayed.

Press the button for less than 0.8 sec-

onds and press it again within 1 sec-

ond to move to and play the previous

song.

• To cancel REPEAT, press this button

again.

8. SEARCH Knob & ENTER

Button

5. SCAN Selection Button

Press the button for 0.8 seconds or

longer to play the song in reverse

direction in fast speed.

Plays each song in the USB device for 10

seconds.

• Turn this knob clockwise to browse

songs after current song, or counter

clockwise to browse songs before cur-

rent song. To play the displayed song,

press the knob.

• Press the [TRACK

] button for less

To cancel SCAN Play, press this button

again.

than 0.8 seconds to move to the next

song. Press the button for 0.8 seconds

or longer to play the song in forward

direction in fast speed.

• Pressing this knob without turning

enters to AUDIO CONTROL mode.

6. INFO Button

Displays the information of the file cur-

rently played in the order of FILE NAME

4 104

Features of your vehicle

(Continued)

✽

NOTICE FOR USING THE

IPOD^®DEVICE

CAUTION IN USING THE

IPOD^®DEVICE

• When the iPod cable is connect-

ed, the system can be switched to

AUX mode even without iPod

device and may cause noise.

Disconnect the iPod cable when

you are not using the iPod device.

• Some iPod models might not sup-

port the communication protocol

and the files will not be played.

Supported iPod models:

• The HYUNDAI iPod Power Cable

is needed in order to operate iPod

with the audio buttons on the

audio system.The USB cable pro-

vided by Apple may cause mal-

function and should not be used

for HYUNDAI vehicles.

- iPod Mini

- iPod 4th(Photo) ~ 6th(Classic)

generation

• When not using iPod with car

audio, detach the iPod cable from

iPod. Otherwise, iPod may remain

in accessory mode, and may not

work properly.

- iPod Nano 1st~4th generation

- iPod Touch 1st~2nd generation

• The order of search or playback of

songs in the iPod can be different

from the order searched in the

audio system.

• If the iPod disabled due to its own

malfunction, reset the iPod. (Reset:

Refer to iPod manual)

❋ The HYUNDAI iPod Power Cable

may be purchased through your

HYUNDAI Dealership.

• When connecting iPod with the

iPod Power Cable, insert the con-

nector to the multimedia socket

completely. If not inserted com-

pletely, communications between

iPod and audio may be interrupted.

• An iPod may not operate normally

on low battery.

• When adjusting the sound effects

of the iPod and the audio system,

the sound effects of both devices

will overlap and might reduce or

distort the quality of the sound.

• Some iPod devices, such as the

iPhone, can be connected through

the Bluetooth^®interface. The device

must have audio Bluetooth^®capa-

bility (such as for stereo headphone

Bluetooth^®). The device can play,

but it will not be controlled by the

audio system.

• Deactivate (turn off) the equalizer

function of an iPod when adjust-

ing the audio system’s volume,

and turn off the equalizer of the

audio system when using the

equalizer of an iPod.

(Continued)

4 105

Features of your vehicle

❋ iPod^®is a trademark of Apple, Inc.

iPod^®(USA/CANADA)

1. iPod Selection Button

2. TRACK Selection Button

3. REPEAT Selection Button

4. RANDOM Playback Button

5. INFO Button

6. CATEGORY Selection Button

7. SEARCH Knob & ENTER Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 106

Features of your vehicle

Using iPod^®

3. REPEAT Button

The order of iPod’s category is SONG,

ALBUMS, ARTISTS, GENRES, and iPod.

Repeats the song currently played.

1. iPod Selection Button

7. SEARCH Knob & ENTER

Button

4. RANDOM Playback Button

If iPod is connected, it switches to the

iPod mode from the previous mode to

play the song files stored in the iPod.

• Press this button for less than 0.8 sec-

onds to shuffle order of all songs in

current category. (Song Random)

When you rotate the knob clockwise, it

will display the songs (category) ahead

of the song currently played (category in

the same level).

If there is no iPod connected, then it dis-

plays the message "No Media" for 3 sec-

onds and returns to the previous mode.

• Press this button for 0.8 seconds or

longer to shuffle order of albums in cur-

rent category. (Album Random)

Also, when you rotate the knob counter-

clockwise, it will display the songs (cate-

gory) before the song currently played

(category in the same level).

2. TRACK Selection Button

• To cancel RANDOM Play, press this

button again.

• Press the [TRACK

] button for less

than 0.8 seconds to play from the

beginning of the song currently played.

To listen to the song displayed in the

song category, press the button to skip to

and play the selected song.

5. INFO Button

Press the button for less than 0.8 sec-

onds and press it again within 1 sec-

ond to move to and play the previous

track.

Displays the information of the file cur-

rently played in the order of TITLE ➟

ARTIST ➟ ALBUM ➟ NORMAL DISPLAY

➟ TITLE ➟... (Displays no information if

the file has no song information.)

Pressing the button changes the BASS,

MIDDLE, TREBLE, FADER and BAL-

ANCE TUNE mode. The mode selected

is shown on the display. After selecting

each mode, rotate the Audio control knob

clockwise or counterclockwise.

Press the button for 0.8 seconds or

longer to play the song in reverse

direction in fast speed.

6. CATEGORY Selection Button

• Press the [TRACK

than 0.8 seconds to move to the next

track.

] button for less

Moves to the upper category from cur-

rently played category of the iPod.

To move to (play) the category (song)

displayed, press TUNE/ENTER knob.

Press the button for 0.8 seconds or

longer to play the song in forward direc-

tion in fast speed.

You will be able to search through the

lower category of the selected category.

4 107

Features of your vehicle

XM SATELLITE RADIO (USA/CANADA)

1. SATELLITE RADIO Selection Button

2. Channel Selection Button

3. Preset Selection Button

4. SCAN Selection Button

5. INFO Selection Button

6. CAT/FOLDER Button

7. Manual Channel Selection Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 108

Features of your vehicle

Using XM Satellite Radio

3. Preset Selection Button

6. CATEGORY Search Button

Push [1]~[6] buttons less than 0.8 sec-

onds to play the channel saved in each

button. Push Preset button for 0.8 sec-

onds or longer to save current channel to

the respective button with a beep.

Your vehicle is equipped with 3 months

complimentary period of XM Satellite

Radio so you have access to over 130

channels of music, information, and

entertainment programming.

• Push [FOLDER

previous category.

] button to search

• Push [CAT

] button to search next

category. To listen to the displayed cat-

egory, press the TUNE/SETUP button.

To scan channel in displayed category,

press the scan button. To search chan-

nel in displayed category, press seek

buttons or turn the tune button clock-

wise/counterclockwise.(CATEGORY

icon is will be turned on in Category

mode)

4. SCAN Selection Button

1. XM Selection Button

Press to hear a brief sampling of all

channel. To cancel the scan mode, press

the button once again.

Turns to XM Satellite Radio Mode. XM

mode toggles in order to XM1➟XM2➟

XM3➟XM1... when the button is pressed

each time.

5. INFO Button

2. Channel Selection Button

Displays the information of the current

channel in the order of Artist/Song title➟

Category/Channel name➟Current Play

Channel➟Artist/Song title➟Category/

Channel name... when the button is

pressed each time.

7. Manual Channel Selection Button

• Push [TRACK

0.8 seconds to select previous channel.

• Push [TRACK ] button for 0.8 sec-

] button for less than

While listening to XM broadcast, rotate

this control to the right or left to search

other channels while listening to current

channel. (Turn to the right to searchhigh-

er channels and left, lower channels)

onds or longer to continuously move to

previous channel.

If can not display the whole text informa-

tion, rotate the tune button to see the

next page.

• Push [SEEK

0.8 seconds to select next channel.

• Push [SEEK ] button for 0.8 sec-

] button for less than

onds or longer to continuously move to

next channel.

• Radio ID : Seek or Tune to XM channel

0 to display the Radio ID.

4 109

Features of your vehicle

(continued)

CAUTION IN USING

BLUETOOTH^®CELLULAR

PHONE

• Do not place the phone near or

inside metallic objects, otherwise

communications with Bluetooth^®

system or cellular service sta-

tions can be disturbed.

• Do not use a cellular phone or

perform Bluetooth^®settings (e.g.

pairing a phone) while driving.

• Some Bluetooth^®-enabled phones

may not be recognized by the

system or fully compatible with

the system.

• Before using Bluetooth^®related

features of the audio system,

refer your phone’s User’s Manual

for phone-side Bluetooth^®opera-

tions.

• While

a

phone is connected

through Bluetooth^®your phone

may discharge quicker than usual

for additional Bluetooth^®-related

operations.

• Some cellular phones or other

devices may cause interference

noise or malfunction to audio

system. In this case, store the

device in a different location may

resolve the situation.

• The phone must be paired to the

audio system to use Bluetooth^®

related features.

• You will not be able to use the

hands-free feature when your

phone (in the car) is outside of

the cellular service area (e.g. in a

tunnel, in a underground, in a

mountainous area, etc.).

• If the cellular phone signal is poor

or the vehicles interior noise is

too loud, it may be difficult to hear

the other person’s voice during a

call.

(Continued)

4 110

Features of your vehicle

■ What is Bluetooth^®?

■ Bluetooth^®Language Setting

BLUETOOTH^®PHONE OPERA-

TION (IF EQUIPPED)

Bluetooth^®is a wireless technology that

allows multiple devices to be connected in

a short range, low-powered devices like

hands-free, stereo headset, wireless remo-

con, etc. For more information, visit the

Bluetooth^®website at www.Bluetooth.com

The system language can be changed by

the following steps:

1. Power on the audio system with the

volume set to an audible level.

1

2. Press and hold

button on the

steering wheel until the audio displays

“Please Wait”.

®

- The Bluetooth system will reply in

currently selected language that it is

changing to the next language.

■

General Features

• This audio system supports Bluetooth^®

hands-free and stereo-headset features.

2

4

5

3

- HANDS-FREE feature: Making or

receiving calls wirelessly through

voice recognition.

- System language cycles between

English, Canadian French and US

Spanish.

- STEREO-HEADSET feature: Playing

music from cellular phones (that sup-

ports A2DP feature) wirelessly.

- Press and hold the

steering wheel for over 10 seconds.

button on the

1.VOLUME button : Raises or lowers

speaker volume.

3. When completed, the audio display

returns to normal.

2.MUTE : Mute the microphone during a

call

®

• Voice recognition engine of the Bluetooth

system supports 3 types of languages:

4. Repeat steps 2 and 3 for the next lan-

guage selection.

3.TALK button : Activates voice recogni-

tion.

- English

- US Spanish

- Canadian French

4.CALL button : Places and transfers

calls.

NOTE:

5.END button : Ends calls or cancels

functions.

The phone needs to be paired again

after changing system language.

- Avoid resting your thumb or finger

✽

NOTICE

on the button as the language

could unintentionally change.

• The phone must be paired to the sys-

tem before using Bluetooth^®features.

• Only one selected (linked) cellular phone

can be used with the system at a time.

• Some phones are not fully compatible

with this system.

4 111

Features of your vehicle

• At any time if you say “help”, the sys-

tem will announce what commands are

available.

■

Voice Recognition Activation

✽ Tip

■

Voice Operation

To get the best performance out of the

Voice Recognition System, observe the

followings:

- Keep the interior of the vehicle as

quiet as possible. Close the window

to eliminate surrounding noise

(traffic noise, vibration sounds,

etc), which may disturb recogniz-

ing the voice command correctly.

- Speak a command after a beep

sound within 5 seconds. Otherwise

the command will not be received

properly.

• The voice recognition engine con-

tained in the Bluetooth^®System can be

activated in the following conditions:

■

Menu tree

The menu tree identifies available voice

®

recognition Bluetooth functions.

- Button Activation

The voice recognition system will be

active when the

button is pressed

and after the sound of a Beep.

- Active Listening

The voice recognition system will be

active for a period of time when the

Voice Recognition system has asked

for a customer response.

Pair phone

Setup

Select phone

Delete phone

Change priority

Bluetooth off

• The system can recognize single dig-

itsfrom zero to nine while number

greater than ten will not be recognized.

- Speak in a natural voice without

pausing between words.

- While receiving voice commands,

Phonebook

Add entry

By voice

• If the command is not recognized, the

system will announce "Pardon" or No

input voice signal from microphone.

(No response)

press the

button on the steer-

ing wheel remote controller to ter-

minate guidance. Voice command

will convert back to waiting mode

to allow the user to say a new voice

command.

By Phone

Change

Delete name

• The system shall cancel voice recogni-

tion mode in following cases : When

Call

By name

pressing the

cancel following the beep. When not

making a call and pressing the but-

button and saying

By number

ton. When voice recognition has failed

3 consecutive times.

4 112

Features of your vehicle

■

Information Display

Phone Setup

All Bluetooth^®related operations can be

performed by voice command or by man-

ual operation.

- By Voice Command:

Press button on the steering wheel

to activate voice recognition.

3) Select desired item by rotating the

TUNE knob, then push the knob.

• Pairing phone

Before using Bluetooth^®features, the

phone must be paired (registered) to the

audio system. Up to 5 phones can be

paired in the system.

- By Manual Operation:

1) Push the [TUNE] knob to enter

SETUP mode.

Note:

Before pairing a mobile phone, check

to see that the Bluetooth^®function in

your mobile phone is set to “ON”

state.

Note:

The pairing procedure of the phone

varies according to each phone

model. Before attempting to pair

phone, please see your phone’s

User’s Guide for instructions.

The Bluetooth^®icon appears on the

upper side of audio display when a

phone is connected.

2) Select “PHONE” item by rotating the

TUNE knob, then push the knob.

4 113

Features of your vehicle

®

Bluetooth device list. Then attempt

pairing on your phone

Note:

“My Phone” say

“Yes” to proceed, otherwise say “Back” or

“Cancel”

Once pairing with the phone is com-

pleted, there is no need to pair with

that phone again unless the phone is

deleted manually from the audio sys-

tem (refer “Deleting Phone” section)

or the vehicle’s information is

removed from the phone.

➉ After Pairing is completed, your phone

will start to transfer phone/contact list

to the audio system.

“Yes”

- This process may take from a few min-

utes to over 10 minutes depending on

the phone model and number of

entries in the phone/contact list.

“Ready for pairing...please use your

phone to connect to the system the

pairing pass key is 0000”

By Voice Recognition

✽ Tip

Press

➀ Press

➁ Say “Set Up”.

- The system replies with available

commands.

button.

Pair the device after searching for

Bluetooth devices in your mobile phone.

Once pairing is complete, you will hear

the following message.

button.

®

Beep~♪

- To skip the information message, press

again and then a beep is heard.

➂ Say “Pair Phone”.

“Setup”

“Pairing Complete”

“Setup” say

“Pair phone”, “Select phone”, “Delete

phone”, “Change priority” or “Bluetooth off”

➃ Say “Yes” to proceed.

➄ Say the name of your phone when

“Connection Complete”

prompted.

- Use any name to uniquely describe

your phone.

“Pair Phone”

“Pair Phone” say

“Yes” to proceed, otherwise say “Back” or

“Cancel”

®

➅ Bluetooth system will repeat the

name you stated.

➆ Say "Yes" to confirm.

“Yes”

➇ The audio displays “searching

passkey: 0000” and asks you to initiate

pairing procedure from the phone.

----

“Please say a name for the phone”

Ex: “My phone” or “John”

®

➈ Search the Bluetooth system on your

phone .Your phone should display

your [vehicle model name] on the

4 114

Features of your vehicle

• Connecting phone

®

When the Bluetooth system is enabled,

• Deleting Phone

The paired phone can be deleted.

By Manual operation

the phone previously used is automati-

cally selected and re-connected. If you

want to select different phone previously

paired, the phone can be selected

through “Select Phone” menu.

- When the phone is deleted, all the infor-

mation associated with that phone is

also be deleted (including phonebook).

- If you want to use the deleted phone

with the audio system again, pairing

procedure must be completed once

more.

Only a selected phone can be used with

the hands-free system at a time.

➀ Select “PAIR” in PHONE menu, then-

proceed from step 5.

By Voice Recognition

➀ Press

➁ Say "Set Up".

➂ Say "Select Phone" after prompt

- The system lists all the registered

phone names.

➃ Say the name or number of desired

phone from the list.

➄ Say "Yes" to confirm.

button.

➀ Press

➁ Say “Set Up”.

➂ Say “Delete Phone” after prompt.

- The system lists all the registered

phone names.

➃ Say the name or number of desired

phone from the list.

➄ Say “Yes” to confirm.

button.

Note:

Until the audio displays “Transfer

®

Complete”, Bluetooth hands-free fea-

ture may not be fully operational.

Note:

If the phone is paired to two or more

vehicles of the same model, i.e. both

vehicles are HMC TUCSON, some

®

By Manual operation

➀ Select “DELETE” in PHONE menu,

then select desired phone from the list.

phones may not handle Bluetooth

By Manual operation

➀ Select “SELECT” in PHONE menu,

then select desired phone from the list.

devices of that name correctly. In this

case, you may need to change the

name displayed on your phone from

TUCSON.

Refer to your phone’s User’s Guide, or

contact your cellular carrier or phone

manufacturer for instructions.

4 115

Features of your vehicle

■

Phone Book (In-Vehicle)

• Adding Entry

• Changing Priority

✽

NOTICE

When several phones are paired to the

audio system, the system attempts to

connect following order when the

- The system can recognize single digits

from zero to nine. Numbers that are

ten or greater cannot be recognized.

- You can enter each digit individually

or group digits together in preferred

string lengths.

- To speed up input, it is a good idea to

group all digits into a continuous

string.

Phone numbers and voice tags can be

registered. Entries registered in the

phone can also be transferred.

®

Bluetooth system is enabled:

1) “Priority” checked phone.

2) Previously connected phone

3) Gives up auto connection.

• Adding Entry by Voice

➀ Press button.

➁ Say "Phonebook".

- The system replies with all available

commands.

- To skip the information message,

- The display corresponding to each

operation appears on the screen as fol-

lows:

- Input operation example:

1. Say: “Nine, nine, five”

By Voice Recognition

➀ Press button.

➁ Say “Set Up”.

press

heard.

again and then a beep is

➂ Say “Change Priority” after prompt.

➟ Display: “995”

2. And say: “Seven, three, four”

➟ Display: “995734”

- The system lists all the registered

phone names.

➃ Say the name or number of desired

phone from the list.

➄ Say “Yes” to confirm.

➂ Say "Add Entry".

➃ Say "By Voice" to proceed.

➄ Say the name of the entry when

prompted.

➅ Say “Yes”to confirm.

➆ Say the phone number of that entry

when prompted.

➇ Say “Store” if phone number input is

finished.

By Manual operation

➀ Select “PRIORITY” in PHONE menu,

then select desired phone from the

list.

➈ Say a phone number type. “Home”,

“Work”, “Mobile”, “Other” or “Default” is

available.

➉ Say “Yes” to complete adding entry.

11

Say “Yes” to store additional location

for this contact, or say “Cancel” to fin-

ish the process.

4 116

Features of your vehicle

• Adding Entry by Phone

➀ Press button.

➁ Say "Phonebook".

➂ Say "Add Entry" after prompt.

➃ Say "By Phone" to proceed.

➄ Say “Yes” to confirm.

• Deleting Name

The registered names can be deleted.

• Direct Calling

➀ Press button.

➁ Sat the following command.

➀ Press button.

➁ Say “Phonebook”

➂ Say “Delete Name” after prompt.

➃ Say the name of the entry (voice tag)

➄ Say “Yes” to confirm.

- Call <John> : Connects the call to John.

- Call <John> on <Mobile> : Connects

the call to John’s mobile phone number.

- Call <John> at <Home> : Connects

the call to john’s home number.

➅ Your phone will start to transfer

phone/contact list to the audio system.

This process may take over 10 min-

utes depending on the phone model

and number of entries.

- Call <John> in <Office> : Connects

the call to John’s office number.

■

Making a Phone Call

• Calling by Name

A phone call can be made by speaking

names registered in the audio system.

➆ Wait till the audio displays “Transfer

Complete” message.

Note:

Calls can be immediately connected

to contacts who name or voice tag are

saved in the phonebook(or contacts).

➀ Press

➁ Say "Call".

button.

• Changing Name

The registered names can be modified.

➂ Say “Name” when prompted.

➃ Say desired name (in phonebook or

voice tag).

➀ Press button.

➁ Say “Phonebook”

➂ Say “Change Name” after prompt.

➃ Say the name of the entry (voice tag)

➄ Say “Yes” to confirm.

➄ Say desired location (phone number

type). Only stored locations can be

selected.

➅ Say “Yes” to confirm and make a call.

➅ Say new desired name.

✽ Tip

A shortcut to each of the following func-

tions is available:

➀ Say “Call Name”

4 117

Features of your vehicle

• Dialing by Number

■

Receiving a Phone Call

Talking on the Phone

A phone call can be made by dialing the

spoken numbers. The system can recog-

nize single digits from zero to nine.

When receiving a phone call, a ringtone

is audible from speakers and the audio

system changes into telephone mode.

When talking on the phone, “Active Calls”

message and the other party’s phone

number (if available) are displayed on the

audio.

➀ Press

➁ Say “Call”.

button.

When receiving a phone call, “Incoming”

message and incoming phone number

(if available) are displayed on the audio.

• To Mute the Microphone

➂ Say “Number” when prompted.

➃ Say desired phone numbers.

➄ Say “Dial” to complete the number and

- Press button on the steering wheel.

• To Finish a Call

• To Answer a Call:

- Press

button on the steering wheel.

make a call.

- Press button on the steering wheel.

• To Reject a Call:

✽

NOTICE

✽ Tip

- Press

• To Adjust Ring Volume:

button on the steering wheel.

In the following situations, you or the

other party may have difficulty hearing

each other:

1. Speaking at the same time, your voice

may not reach each other parties. (This

is not a malfunction.) Speak alternate-

ly with the other party on the phone.

A shortcut to each of the following func-

tions is available:

➀ Say “Dial Number”

- Use VOLUME buttons on the steering

wheel.

➁ Say “Dial <digit>”

• To Transfer a Call to the Phone (Secret

Call):

- Press and hold

button on the steer-

ing wheel until the audio system trans-

fers a call to the phone.

®

2. Keep the Bluetooth volume to a low

level. High-level volume may result in

distortion and echo.

3. When driving on a rough road.

4. When driving at high speeds.

5. When the window is open.

6. When the air conditioning vents are

facing the microphone.

7. When the sound of the air condition-

ing fan is loud.

4 118

Features of your vehicle

®

• Please refer to User’s Guide of your

phone for more detailed informa-

tions. To stop music, try stop music

by the phone and change audio

mode to different one. (e.g. FM, CD,

iPod, ...)

• LANGUAGE (Language of Bluetooth

voice recognition)

■

Using the head unit as Bluetooth

music

While in ADVANCED menu, press

“LANGUAGE”. To change the language,

select the desired language and press

the [ENTER] button.

The head unit supports A2DP (Audio

Advanced Distribution Profile) and AVRCP

(Audio Video Remote Control Profile).

Both profiles are available for listening to the

®

MP3 music via Bluetooth cellular phone

■

ADVANCED Menu

®

supporting above Bluetooth profiles.

To play MP3 music from the Bluetooth

• BT OFF

While in ADVANCED menu, press “BT

After pressing the [SETUP] button, press

the PHONE menu. while in PHONE

menu, press the “ADVANCED” menu to

®

OFF” to turn off the Bluetooth System.

cellular phone, press the [AUX] button

until “MP3 Play” is displayed on the LCD.

Then try playing music by phone.

®

make Bluetooth Phone settings.(The

ADVANCED menu may differ according to

audio specifications.)

®

When playing music from the Bluetooth

cellular phone, the head unit displays

MP3 MODE.

• IN VOL.

(Bluetooth call volume adjustments)

®

NOTE:

While in ADVANCED menu, press “IN

VOL.” Use the knob key to set the desired

volume and press the [ENTER] button.

• Not only MP3 files, all the sounds

that the phone supports can be

heard by the audio system.

®

• The Bluetooth cellular phones shall

• CONTACTS

(Automatic Phonebook download setting)

feature A2DP and AVRCP functions.

• Some A2DP and AVRCP Bluetooth

®

While in ADVANCED menu, press

“CONTACTS”. To automatically save the

contacts and call history in your mobile

phone each time you connect a mobile

device, press Yes. If you do not wish for

automatic download, press No.

cellular phones may not play music

through the head unit on first try.

Please try the below;

i.e : Menu➟Filemanager➟Music➟

Option➟Play via Bluetooth

4 119

Features of your vehicle

■

Key matrix

Class

No.

Connected

Normal mode BT SETUP menu

KEY

Paired H/P

Empty

Disconnected

Not Connecting

2nd Call

Outgoing Call

Incoming Call

Active Call

2nd call

Not Paired

Accept Call

1st Call:waiting 2nd Call:waiting

2nd Call:active 1st Call:active

-

SHORT

1

Transfer call:secret call

-

LONG

VR

Reject Call

End Call

SHORT

MODE Cancel MODE Cancel MODE Cancel MODE Cancel

2

Speaker

Adaptation

Speaker

Adaptation

LONG

-

[10sec]

(Only English)

SHORT

Active

-

3

LONG

Change

language

[10sec]

4 120

Features of your vehicle for Your Hyundai Ix35 SUV First Generation (2009-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals