Get Features of your vehicle -> AUDIO SYSTEM Guide for Hyundai Ix35 SUV First Generation (2009-2015)

Features of your vehicle

AUDIO SYSTEM

✽

NOTICE

(Continued)

CAUTION

If you install an aftermarket HID head-

lamp, your vehicle's audio and electron-

ic device may malfunction.

• The vehicle center of gravity will

be higher when items are loaded

onto the roof rack. Avoid sudden

starts, braking, sharp turns,

abrupt maneuvers or high speeds

that may result in loss of vehicle

control or rollover resulting in an

accident.

• Before entering a place with a low

height clearance or a car wash,

remove the antenna by rotating it

counterclockwise. If not, the

antenna may be damaged.

■ Type A

■ Type B

• When reinstalling your antenna, it

is important that it is fully tight-

ened and adjusted to the upright

position to ensure proper recep-

tion. But it could be removed

when parking the vehicle or when

loading cargo on the roof rack.

• Always drive slowly and turn cor-

ners carefully when carrying

items on the roof rack. Severe

wind updrafts, caused by passing

vehicles or natural causes, can

cause sudden upward pressure

on items loaded on the roof rack.

This is especially true when car-

rying large, flat items such as

wood panels or mattresses. This

could cause the items to fall off

the roof rack and cause damage

to your vehicle or others around

you.

• When cargo is loaded on the roof

rack, do not place the cargo near

the antenna pole to ensure proper

reception.

OHM048154

Antenna

Roof antenna

Your vehicle uses a roof antenna to

receive both AM and FM broadcast sig-

nals. This antenna is removable. To

remove the antenna, turn it counterclock-

wise. To install the antenna, turn it clock-

wise.

• To prevent damage or loss of

cargo while driving, check fre-

quently before or while driving to

make sure the items on the roof

rack are securely fastened.

4 89

Features of your vehicle

CD/USB/iPod mode

It will function as TRACK UP/DOWN

button.

MODE (1)

Press the button to change audio source.

- FM(1~2)➟AM➟SAT(1~3)➟CD➟USB

AUX(iPod) FM...

VOLUME (VOL

/

) (3)

1

2

• Push the lever upward ( ) to increase

the volume.

SEEK/PRESET (

/

) (2)

The SEEK/PRESET button has different

functions based on the system mode.

3

• Push the lever downward ( ) to decrease

the volume.

4

For the following functions the button

should be pressed for 0.8 second or

more.

MUTE (4)

• Press the button to mute the sound

Steering wheel audio control

(if equipped)

RADIO mode

It will function as the AUTO SEEK select

button.

• Press the button to turn off the micro-

phone during a telephone call.

The steering wheel may incorporate

audio control buttons. These buttons are

installed to promote safe driving.

Detailed information for audio control

buttons are described in the following

pages in this section.

CD/USB/iPod mode

It will function as the FF/REW button.

CAUTION

Do not operate audio remote con-

trol buttons simultaneously.

If the SEEK/PRESET button is pressed

for less than 0.8 second, it will work as

follows in each mode.

RADIO mode

It will function as the PRESET STATION

buttons.

4 90

Features of your vehicle

FM reception

AM reception

OLM049195

JBM001

JBM002

AM broadcasts can be received at

greater distances than FM broadcasts.

This is because AM radio waves are

transmitted at low frequencies. These

long, low frequency radio waves can fol-

low the curvature of the earth rather than

travelling straight out into the atmos-

phere. In addition, they curve around

obstructions so that they can provide bet-

ter signal coverage.

How vehicle audio works

Aux, USB and iPod port

(if equipped)

AM and FM radio signals are broadcast

from transmitter towers located around

your city. They are intercepted by the

radio antenna on your vehicle.This signal

is then received by the radio and sent to

your vehicle speakers.

If your vehicle has an aux and/or

USB(universal serial bus) port or iPod

port, you can use an aux port to connect

audio devices and the USB port to plug

in a USB device.

When a strong radio signal has reached

your vehicle, the precise engineering of

your audio system ensures the best pos-

sible quality reproduction. However, in

some cases the signal coming to your

vehicle may not be strong and clear. This

can be due to factors such as the dis-

tance from the radio station, closeness of

other strong radio stations or the pres-

ence of buildings, bridges or other large

obstructions in the area.

Both ports are used together with the

accessory iPod cable to connect an iPod.

✽

NOTICE

When using a portable audio device

connected to the power outlet, noise may

occur during playback. If this happens,

use the power source of the portable

audio device.

❈ iPod^®is a trademark of Apple Inc.

4 91

Features of your vehicle

FM radio station

JBM003

JBM004

JBM005

FM broadcasts are transmitted at high

frequencies and do not bend to follow the

earth's surface. Because of this, FM

broadcasts generally begin to fade at

short distances from the station.

• Fading - As your vehicle moves away

from the radio station, the signal will

weaken and sound will begin to fade.

When this occurs, we suggest that you

select another stronger station.

• Station Swapping - As a FM signal

weakens, another more powerful sig-

nal near the same frequency may

begin to play. This is because your

radio is designed to lock onto the clear-

est signal. If this occurs, select another

station with a stronger signal.

Also, FM signals are easily affected by

buildings, mountains, or other obstruc-

tions.These can result in certain listening

conditions which might lead you to

believe a problem exists with your radio.

The following conditions are normal and

do not indicate radio trouble:

• Flutter/Static - Weak FM signals or

large obstructions between the trans-

mitter and your radio can disturb the

signal causing static or fluttering nois-

es to occur. Reducing the treble level

may lessen this effect until the distur-

bance clears.

• Multi-Path Cancellation - Radio signals

being received from several directions

can cause distortion or fluttering. This

can be caused by a direct and reflect-

ed signal from the same station, or by

signals from two stations with close

frequencies. If this occurs, select

another station until the condition has

passed.

4 92

Features of your vehicle

• If you are driving on a mountain road

where is blocked by mountains.

Satellite radio reception

You may experience receiving difficulties

receiving XM™ satellite radio signals in

the following situations.

• If you are driving in an area with tall

trees that block the signal(10m or

more), for example on an road that

goes through a dense forest.

• If you are driving in a tunnel or a cov-

ered parking area.

• The signal can become weak in some

areas that are not covered by the XM™

repeater network.

• If you are driving beneath the top level

of a multi-level freeway.

• If you drive under a bridge.

• If you are driving next to a tall vehi-

cle(such as a truck or a bus) that block

the signal.

NOTE:

There may be other unforeseen cir-

cumstances leading to reception

problems with XM™ satellite radio

signal.

• If you are driving in a valley where the

surrounding hills or peaks block the

signal from the satellite.

4 93

Features of your vehicle

Using a cellular phone or a two-way

radio

• Keep CDs in their cases after use to

protect them from scratches or dirt.

Care of discs

• If the temperature inside the vehicle is

too high, open the vehicle windows for

ventilation before using your vehicle

audio.

When a cellular phone is used inside the

vehicle, noise may be produced from the

audio equipment. This does not mean

that something is wrong with the audio

equipment. In such a case, use the cellu-

lar phone at a place as far as possible

from the audio equipment.

• Depending on the type of CD-R/CD-

RW CDs, certain CDs may not operate

normally according to manufacturing

companies or making and recording

methods. In such circumstances, if you

still continue to use those CDs, they

may cause the malfunction of your

vehicle audio system.

• It is illegal to copy and use MP3/WMA

files without permission. Use CDs that

are created only by lawful means.

• Do not apply volatile agents such as

benzene and thinner, normal cleaners

and magnetic sprays made for ana-

logue disc onto CDs.

WARNING

✽

NOTICE - Playing an

Do not use a cellular phone while

driving. Stop at a safe location to

use a cellular phone.

Incompatible Copy

Protected Audio CD

• To prevent the disc surface from get-

ting damaged. Hold and carry CDs by

the edges or the edges of the center

hole only.

Some copy protected CDs, which do not

comply with the international audio CD

standards (Red Book), may not play on

your vehicle audio. Please note that if

you try to play copy protected CDs and

the CD player does not perform correct-

ly the CDs maybe defective, not the CD

player.

• Clean the disc surface with a piece of

soft cloth before playback (wipe it from

the center to the outside edge).

• Do not damage the disc surface or

attach pieces of sticky tape or paper

onto it.

• Make sure objects other than CDs are

not inserted into the CD player (Do not

insert more than one CD at a time).

4 94

Features of your vehicle

RADIO, SET UP, VOLUME, AUDIO CONTROL (USA/CANADA)

1. AM Selection Button

2. FM Selection Button

3. Automatic Station Seek Button

4. Power ON/OFF Button and Volume

Control Knob

5. Preset Selection Button

6. SCAN Selection Button

7. DISP Button

8. SETUP Button

9. TUNE & AUDIO Control Knob

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 95

Features of your vehicle

Using RADIO, SETUP, VOLUME

and AUDIO CONTROL

5. Preset Selection Button

8. SETUP Button

• Press [1]~[6] buttons less than 0.8 sec-

ond to play the station saved in each

button.

Press this Button to enter SETUP mode,

If no action is taken for 8 seconds, it will

return to previous mode.

1. AM Selection Button

Pressing the [AM] button selects the AM

band. AM Mode is displayed on the LCD.

• Press [1]~[6] button more than 0.8 sec-

ond or longer to save the current station

to the respective button with a beep.

In “SETUP” mode, rotate the TUNE knob

to move the cursor between items, and

push the TUNE knob to select.

2. FM Selection Button

Turns to FM mode and toggles FM1 and

FM2 when the button is pressed each

time.

6. SCAN Button

• SCROLL

Select whether long file names are

scrolled continuously (“ON”) or just once

(“OFF”).

• When the button is pressed, it auto-

matically scans the radio stations

upwards.

3. Automatic Station Seek Button

• The SCAN feature steps through each

station, starting from the initial station,

for ten seconds.

• SDVC

• When the [SEEK

] is pressed, it will

Select this item to turn the SDVC(Speed

Dependent Volume Control) feature ON

or OFF. If it is turned ON, volume level is

adjusted automatically according to the

vehicle speed.

automatically tune to the next lower

station.

• Press the [SCAN] button again to stop

the scan feature and to listen to the

currently selected channel.

• When the [SEEK

] is pressed, it will

automatically tune to the next higher

station.

7. DISP Button

• P.BASS (PowerBass)

Turn the LCD Display & Backlight on/off

when [DISP] button press.

4. Power ON/OFF Button & Volume

Control Knob

This function creates virtual sound

effects and allows adjustments to the

BASS level.

• Turns the audio system on/off when

the ignition switch is on ACC or ON.

HIGH ➟ MID ➟ LOW ➟ OFF

• If the knob is turned clockwise/counter-

clockwise, the volume will increase

/decrease.

• XM

Select default display of XM mode.

“Category/Channel name” or “Artist/Song

Title” can be selected.

4 96

Features of your vehicle

• PHONE (if available)

• FADER Control

9. TUNE Knob & Audio Control

Knob

Select this item to enter BLUETOOTH^®

setup mode. Refer to “BLUETOOTH

PHONE OPERATION” section for

detailed information.

Turn the control knob clockwise to

emphasize rear speaker sound (front

speaker sound will be attenuated). When

the control knob is turned counterclock-

wise, front speaker sound will be empha-

sized (rear speaker sound will be attenu-

ated).

• Rotate the knob clockwise or counter-

clock wise to increase or decrease from

current frequency.

(AM 10kHz, FM 200kHz)

• Adjusting the Clock

Press the [SETUP] button. Use the vol-

ume controller to adjust the clock in the

following order: CLOCK ENTER hour or

minute.

Pressing the button changes the BASS,

MIDDLE, TREBLE, FADER and BAL-

ANCE TUNE mode. The mode selected

is shown on the display. After selecting

each mode, rotate the Audio control knob

clockwise or counterclockwise.

•

• BALANCE Control

Rotate the knob clockwise to emphasize

Adjust the hour and press the [ENTER]

button to set. Use the same method to

right speaker sound (left speaker sound

will be attenuated). When the control

knob is turned counter clockwise, left

speaker sound will be emphasized (right

speaker sound will be attenuated).

adjust the minute and press the [ENTER]

button to complete and exit from clock

adjustment mode.

• BASS Control

To increase the BASS, rotate the knob

clockwise, while to decrease the BASS,

rotate the knob counterclockwise.

Pressing the [SETUP] button while in

POWER OFF screen will allow the user

to make immediately adjustments to the

clock.

• MIDDLE Control

To increase the MIDDLE, rotate the knob

clockwise, while to decrease the MID-

DLE, rotate the knob counterclockwise.

• TREBLE Control

To increase the TREBLE, rotate the knob

clockwise, while to decrease the TRE-

BLE, rotate the knob counterclockwise.

4 97

Features of your vehicle

CD (USA/CANADA)

1. CD Loading Slot

2. CD Eject Button

3. CD Selection Button

4. Automatic Station Seek Button

5. RANDOM play Button

6. REPEAT Button

7. CD Indicator

8. SCAN Play Button

9. INFO Button

10. FOLDER Moving Button

11. SEARCH Knob & ENTER Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 98

Features of your vehicle

If there is no CD, then the message "No

CD" will become displayed on the LCD

for 3 seconds and returns to the previous

mode.

• To cancel RANDOM Play, press this

button again.

Using CD Player

1. CD Loading Slot

6. REPEAT Button

Insert a CD label side up and gently push

in while ignition switch is on ACC or ON.

The audio automatically switches to CD

mode and begins to play the CD. If the

audio was turned off, audio power will

automatically turned on as the CD is

inserted.

• Press this button for less than 0.8 sec-

onds to repeat current song.

4. Track Selection Button

• Press [TRACK

] button for less than

0.8 seconds to play from the beginning

of current song.

• Press this button for 0.8 seconds or

longer to repeat all songs in current

folder.

• Press [TRACK

] button for less than

• To cancel REPEAT, press this button

again.

0.8 seconds and press again within 1

seconds to play the previous song.

- This audio only recognizes 12cm-size, CD-

DA(Audio CD) or ISO data-CD (MP3 CD).

• Press [TRACK

] button for 0.8 sec-

- If UDF data-CD or non-CD(e.g. DVD) is

inserted, "Reading Error" message will

be displayed and the disc will be ejected.

7. CD Indicator

onds or longer to initiate reverse direc-

tion high speed sound search of cur-

rent song.

When car ignition switch is ACC or ON

and if the CD is loaded, this indicator is

lit. If the CD is ejected, the light is turned

off.

• Press [TRACK

0.8 seconds to play the next song.

• Press [TRACK ] button for 0.8 sec-

onds or longer to initiate forward direc-

tion high speed sound search of cur-

rent song.

] button for less than

CAUTION

Do not insert a CD if CD indicator is

lit.

8. SCAN Play Button

Play each song in the CD for 10 seconds.

To cancel SCAN Play, press this button

again.

2. CD Eject Button

• Press [ ] button to eject the CD. This

button works regardless of ignition

switch status.

5. RANDOM Play Button

9. INFO Button

• Press this button for less than 0.8 sec-

onds to play songs randomly in current

folder.

Displaces the information of the current

song.

3. CD Selection Button

• Press this button for 0.8 seconds or

longer to play songs randomly in entire

CD.

- Audio CD : Disc Title/Artist, Track Title

/Artist, Total Tracks.

If there is a CD in the CD DECK it switch-

es to CD mode.

4 99

Features of your vehicle

- MP3 CD : File Name, Title, Artist,

Album, Folder, Total Files (Not displayed

if the information is unavailable on the

CD or file.)

2. Folder playing order :

NOTE:

Order of playing files(folders) :

10. FOLDER Moving Button

• Press [FOLDER

] button to move to

child folder of the current folder and

display the first song in the folder.

❋ If no song file is contained in the

folder, that folder is not displayed.

Press TUNE/ ENTER knob to move to

the folder displayed. It will play the first

song in the folder.

• Press [FOLDER

] button to move to

parent folder of the current folder and

display the first song in the folder.

Press TUNE/ENTER knob to move to

the folder displayed.

11. SEARCH Knob & ENTER

Button

• Turn this knob clockwise to browse

songs after current song, or counter-

clockwise to browse songs before cur-

rent song. To play the displayed song,

press the knob.

1. Song playing order : to sequen-

tially.

• Pressing this knob without turning

enters to AUDIO CONTROL mode.

4 100

Features of your vehicle

(Continued)

• An encrypted MP3 PLAYER is not

recognizable.

(Continued)

CAUTION IN USING

USB DEVICE

• To use an external USB device,

make sure the device is not con-

nected when starting up the vehi-

cle. Connect the device after

starting up.

• If you disconnect the external USB

device during playback in USB

mode, the external USB device can

be damaged or may malfunction.

Therefore, disconnect the external

USB device when the audio is

turned off or in another mode. (e.g,

Radio, XM or CD)

• Depending on the condition of

the external USB device, the con-

nected external USB device can

be unrecognizable.

• When the formatted byte/sector

setting of External USB device is

not either 512BYTE or 2048BYTE,

then the device will not be recog-

nized.

• If you start the engine when the

USB device is connected, it may

damage the USB device. (USB

flashdrives are very sensitive to

electric shock.)

• Depending on the type and

capacity of the external USB

device or the type of the files

stored in the device, there is a dif-

ference in the time taken for

recognition of the device.

• Use only a USB device formatted

to FAT 12/16/32.

• If the engine is started up or

turned off while the external USB

device is connected, the external

USB device may not work.

• USB devices without USB I/F

authentication may not be recog-

nizable.

• Do not use the USB device for

purposes other than playing

music files.

• It may not play inauthentic MP3 or

WMA files.

1) It can only play MP3 files with the

• Make sure the USB connection

terminal does not come in con-

tact with the human body or other

objects.

• Use of USB accessories such as

rechargers or heaters using USB

I/F may lower performance or

cause trouble.

compression

8Kbps~320Kbps.

rate

between

• If you repeatedly connect or dis-

connect the USB device in a short

period of time, it may break the

device.

2) It can only play WMA music files

with the compression rate

between 8Kbps~320Kbps.

• If you use devices such as a USB

hub purchased separately, the

vehicle’s audio system may not

recognize the USB device. In that

case, connect the USB device

directly to the multimedia termi-

nal of the vehicle.

• Take precautions for static elec-

tricity when connecting or dis-

connecting the external USB

device.

• You may hear a strange noise

when connecting or disconnect-

ing a USB device.

(Continued)

4 101

Features of your vehicle

(Continued)

• If the USB device is divided by

logical drives, only the music files

on the highest-priority drive are

recognized by car audio.

• Please avoid using USB memory

products which can be used as

key chains or cellular phone

accessories as they could cause

damage to the USB jack. Please

make certain only to use plug

type connector products as

shown below.

• Devices such as MP3 Player/

Cellular phone/Digital camera can

be unrecognizable by standard

USB I/F can be unrecognizable.

• Some non-standard USB devices

(METAL COVER TYPE USB) can

be unrecognizable.

• Some USB flash memory readers

(such as CF, SD, microSD, etc.) or

external-HDD type devices can be

unrecognizable.

• Music files protected by DRM

(DIGITAL RIGHTS MANAGE-

MENT) are not recognizable.

• The data in the USB memory may

be lost while using this audio.

Always back up important data on

a personal storage device.

(Continued)

4 102

Features of your vehicle

AUX/USB (USA/CANADA)

1. AUX/USB Selection Button

2. TRACK Selection Button

3. RANDOM Playback Button

4. REPEAT Selection Button

5. SCAN Selection Button

6. INFO Button

7. FOLDER Moving Button

8. SEARCH Knob & ENTER Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 103

Features of your vehicle

➟ TITLE ➟ ARTIST ➟ ALBUM ➟ FOLDER

➟ TOTAL FILE ➟ NORMAL DISPLAY ➟

FILE NAME ➟… (Displays no informa-

tion if the file has no song information.)

3. RANDOM Playback Button

Using USB device

• Press this button for less than 0.8 sec-

onds to play songs randomly in current

folder.

1. AUX/USB Selection Button

If the auxiliary device is connected, it

switches to AUX or USB mode to play the

sound from the auxiliary player.

• Press this button for 0.8 seconds or

longer to play songs randomly in entire

USB device.

7. FOLDER Moving Button

• Press [FOLDER

] button to move to

If there is no auxiliary device, then the

message "No Media" will become dis-

played on the LCD for 3 seconds and

returns to previous mode.

• To cancel RANDOM play, press this

button again.

child folder of the current folder and

display the first song in the folder.

Press TUNE/ ENTER knob to move to

the folder displayed. It will play the first

song in the folder.

4. REPEAT Button

2. TRACK Selection Button

• Press this button for less than 0.8 sec-

onds to repeat current song.

• Press [FOLDER

] button to move to

• Press the [TRACK

] button for less

parent folder display the first song in

the folder.

• Press this button for 0.8 seconds or

longer to repeat all songs in current

folder.

than 0.8 seconds to play from the

beginning of the current song.

Press TUNE/ENTER knob to move to

the folder displayed.

Press the button for less than 0.8 sec-

onds and press it again within 1 sec-

ond to move to and play the previous

song.

• To cancel REPEAT, press this button

again.

8. SEARCH Knob & ENTER

Button

5. SCAN Selection Button

Press the button for 0.8 seconds or

longer to play the song in reverse

direction in fast speed.

Plays each song in the USB device for 10

seconds.

• Turn this knob clockwise to browse

songs after current song, or counter

clockwise to browse songs before cur-

rent song. To play the displayed song,

press the knob.

• Press the [TRACK

] button for less

To cancel SCAN Play, press this button

again.

than 0.8 seconds to move to the next

song. Press the button for 0.8 seconds

or longer to play the song in forward

direction in fast speed.

• Pressing this knob without turning

enters to AUDIO CONTROL mode.

6. INFO Button

Displays the information of the file cur-

rently played in the order of FILE NAME

4 104

Features of your vehicle

(Continued)

✽

NOTICE FOR USING THE

IPOD^®DEVICE

CAUTION IN USING THE

IPOD^®DEVICE

• When the iPod cable is connect-

ed, the system can be switched to

AUX mode even without iPod

device and may cause noise.

Disconnect the iPod cable when

you are not using the iPod device.

• Some iPod models might not sup-

port the communication protocol

and the files will not be played.

Supported iPod models:

• The HYUNDAI iPod Power Cable

is needed in order to operate iPod

with the audio buttons on the

audio system.The USB cable pro-

vided by Apple may cause mal-

function and should not be used

for HYUNDAI vehicles.

- iPod Mini

- iPod 4th(Photo) ~ 6th(Classic)

generation

• When not using iPod with car

audio, detach the iPod cable from

iPod. Otherwise, iPod may remain

in accessory mode, and may not

work properly.

- iPod Nano 1st~4th generation

- iPod Touch 1st~2nd generation

• The order of search or playback of

songs in the iPod can be different

from the order searched in the

audio system.

• If the iPod disabled due to its own

malfunction, reset the iPod. (Reset:

Refer to iPod manual)

❋ The HYUNDAI iPod Power Cable

may be purchased through your

HYUNDAI Dealership.

• When connecting iPod with the

iPod Power Cable, insert the con-

nector to the multimedia socket

completely. If not inserted com-

pletely, communications between

iPod and audio may be interrupted.

• An iPod may not operate normally

on low battery.

• When adjusting the sound effects

of the iPod and the audio system,

the sound effects of both devices

will overlap and might reduce or

distort the quality of the sound.

• Some iPod devices, such as the

iPhone, can be connected through

the Bluetooth^®interface. The device

must have audio Bluetooth^®capa-

bility (such as for stereo headphone

Bluetooth^®). The device can play,

but it will not be controlled by the

audio system.

• Deactivate (turn off) the equalizer

function of an iPod when adjust-

ing the audio system’s volume,

and turn off the equalizer of the

audio system when using the

equalizer of an iPod.

(Continued)

4 105

Features of your vehicle

❋ iPod^®is a trademark of Apple, Inc.

iPod^®(USA/CANADA)

1. iPod Selection Button

2. TRACK Selection Button

3. REPEAT Selection Button

4. RANDOM Playback Button

5. INFO Button

6. CATEGORY Selection Button

7. SEARCH Knob & ENTER Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 106

Features of your vehicle

Using iPod^®

3. REPEAT Button

The order of iPod’s category is SONG,

ALBUMS, ARTISTS, GENRES, and iPod.

Repeats the song currently played.

1. iPod Selection Button

7. SEARCH Knob & ENTER

Button

4. RANDOM Playback Button

If iPod is connected, it switches to the

iPod mode from the previous mode to

play the song files stored in the iPod.

• Press this button for less than 0.8 sec-

onds to shuffle order of all songs in

current category. (Song Random)

When you rotate the knob clockwise, it

will display the songs (category) ahead

of the song currently played (category in

the same level).

If there is no iPod connected, then it dis-

plays the message "No Media" for 3 sec-

onds and returns to the previous mode.

• Press this button for 0.8 seconds or

longer to shuffle order of albums in cur-

rent category. (Album Random)

Also, when you rotate the knob counter-

clockwise, it will display the songs (cate-

gory) before the song currently played

(category in the same level).

2. TRACK Selection Button

• To cancel RANDOM Play, press this

button again.

• Press the [TRACK

] button for less

than 0.8 seconds to play from the

beginning of the song currently played.

To listen to the song displayed in the

song category, press the button to skip to

and play the selected song.

5. INFO Button

Press the button for less than 0.8 sec-

onds and press it again within 1 sec-

ond to move to and play the previous

track.

Displays the information of the file cur-

rently played in the order of TITLE ➟

ARTIST ➟ ALBUM ➟ NORMAL DISPLAY

➟ TITLE ➟... (Displays no information if

the file has no song information.)

Pressing the button changes the BASS,

MIDDLE, TREBLE, FADER and BAL-

ANCE TUNE mode. The mode selected

is shown on the display. After selecting

each mode, rotate the Audio control knob

clockwise or counterclockwise.

Press the button for 0.8 seconds or

longer to play the song in reverse

direction in fast speed.

6. CATEGORY Selection Button

• Press the [TRACK

than 0.8 seconds to move to the next

track.

] button for less

Moves to the upper category from cur-

rently played category of the iPod.

To move to (play) the category (song)

displayed, press TUNE/ENTER knob.

Press the button for 0.8 seconds or

longer to play the song in forward direc-

tion in fast speed.

You will be able to search through the

lower category of the selected category.

4 107

Features of your vehicle

XM SATELLITE RADIO (USA/CANADA)

1. SATELLITE RADIO Selection Button

2. Channel Selection Button

3. Preset Selection Button

4. SCAN Selection Button

5. INFO Selection Button

6. CAT/FOLDER Button

7. Manual Channel Selection Button

❋There will be no

,

logo if the Bluetooth^®/XM SATELLITE feature is not supported.

4 108

Features of your vehicle

Using XM Satellite Radio

3. Preset Selection Button

6. CATEGORY Search Button

Push [1]~[6] buttons less than 0.8 sec-

onds to play the channel saved in each

button. Push Preset button for 0.8 sec-

onds or longer to save current channel to

the respective button with a beep.

Your vehicle is equipped with 3 months

complimentary period of XM Satellite

Radio so you have access to over 130

channels of music, information, and

entertainment programming.

• Push [FOLDER

previous category.

] button to search

• Push [CAT

] button to search next

category. To listen to the displayed cat-

egory, press the TUNE/SETUP button.

To scan channel in displayed category,

press the scan button. To search chan-

nel in displayed category, press seek

buttons or turn the tune button clock-

wise/counterclockwise.(CATEGORY

icon is will be turned on in Category

mode)

4. SCAN Selection Button

1. XM Selection Button

Press to hear a brief sampling of all

channel. To cancel the scan mode, press

the button once again.

Turns to XM Satellite Radio Mode. XM

mode toggles in order to XM1➟XM2➟

XM3➟XM1... when the button is pressed

each time.

5. INFO Button

2. Channel Selection Button

Displays the information of the current

channel in the order of Artist/Song title➟

Category/Channel name➟Current Play

Channel➟Artist/Song title➟Category/

Channel name... when the button is

pressed each time.

7. Manual Channel Selection Button

• Push [TRACK

0.8 seconds to select previous channel.

• Push [TRACK ] button for 0.8 sec-

] button for less than

While listening to XM broadcast, rotate

this control to the right or left to search

other channels while listening to current

channel. (Turn to the right to searchhigh-

er channels and left, lower channels)

onds or longer to continuously move to

previous channel.

If can not display the whole text informa-

tion, rotate the tune button to see the

next page.

• Push [SEEK

0.8 seconds to select next channel.

• Push [SEEK ] button for 0.8 sec-

] button for less than

onds or longer to continuously move to

next channel.

• Radio ID : Seek or Tune to XM channel

0 to display the Radio ID.

4 109

Features of your vehicle

(continued)

CAUTION IN USING

BLUETOOTH^®CELLULAR

PHONE

• Do not place the phone near or

inside metallic objects, otherwise

communications with Bluetooth^®

system or cellular service sta-

tions can be disturbed.

• Do not use a cellular phone or

perform Bluetooth^®settings (e.g.

pairing a phone) while driving.

• Some Bluetooth^®-enabled phones

may not be recognized by the

system or fully compatible with

the system.

• Before using Bluetooth^®related

features of the audio system,

refer your phone’s User’s Manual

for phone-side Bluetooth^®opera-

tions.

• While

a

phone is connected

through Bluetooth^®your phone

may discharge quicker than usual

for additional Bluetooth^®-related

operations.

• Some cellular phones or other

devices may cause interference

noise or malfunction to audio

system. In this case, store the

device in a different location may

resolve the situation.

• The phone must be paired to the

audio system to use Bluetooth^®

related features.

• You will not be able to use the

hands-free feature when your

phone (in the car) is outside of

the cellular service area (e.g. in a

tunnel, in a underground, in a

mountainous area, etc.).

• If the cellular phone signal is poor

or the vehicles interior noise is

too loud, it may be difficult to hear

the other person’s voice during a

call.

(Continued)

4 110

Features of your vehicle

■ What is Bluetooth^®?

■ Bluetooth^®Language Setting

BLUETOOTH^®PHONE OPERA-

TION (IF EQUIPPED)

Bluetooth^®is a wireless technology that

allows multiple devices to be connected in

a short range, low-powered devices like

hands-free, stereo headset, wireless remo-

con, etc. For more information, visit the

Bluetooth^®website at www.Bluetooth.com

The system language can be changed by

the following steps:

1. Power on the audio system with the

volume set to an audible level.

1

2. Press and hold

button on the

steering wheel until the audio displays

“Please Wait”.

®

- The Bluetooth system will reply in

currently selected language that it is

changing to the next language.

■

General Features

• This audio system supports Bluetooth^®

hands-free and stereo-headset features.

2

4

5

3

- HANDS-FREE feature: Making or

receiving calls wirelessly through

voice recognition.

- System language cycles between

English, Canadian French and US

Spanish.

- STEREO-HEADSET feature: Playing

music from cellular phones (that sup-

ports A2DP feature) wirelessly.

- Press and hold the

steering wheel for over 10 seconds.

button on the

1.VOLUME button : Raises or lowers

speaker volume.

3. When completed, the audio display

returns to normal.

2.MUTE : Mute the microphone during a

call

®

• Voice recognition engine of the Bluetooth

system supports 3 types of languages:

4. Repeat steps 2 and 3 for the next lan-

guage selection.

3.TALK button : Activates voice recogni-

tion.

- English

- US Spanish

- Canadian French

4.CALL button : Places and transfers

calls.

NOTE:

5.END button : Ends calls or cancels

functions.

The phone needs to be paired again

after changing system language.

- Avoid resting your thumb or finger

✽

NOTICE

on the button as the language

could unintentionally change.

• The phone must be paired to the sys-

tem before using Bluetooth^®features.

• Only one selected (linked) cellular phone

can be used with the system at a time.

• Some phones are not fully compatible

with this system.

4 111

Features of your vehicle

• At any time if you say “help”, the sys-

tem will announce what commands are

available.

■

Voice Recognition Activation

✽ Tip

■

Voice Operation

To get the best performance out of the

Voice Recognition System, observe the

followings:

- Keep the interior of the vehicle as

quiet as possible. Close the window

to eliminate surrounding noise

(traffic noise, vibration sounds,

etc), which may disturb recogniz-

ing the voice command correctly.

- Speak a command after a beep

sound within 5 seconds. Otherwise

the command will not be received

properly.

• The voice recognition engine con-

tained in the Bluetooth^®System can be

activated in the following conditions:

■

Menu tree

The menu tree identifies available voice

®

recognition Bluetooth functions.

- Button Activation

The voice recognition system will be

active when the

button is pressed

and after the sound of a Beep.

- Active Listening

The voice recognition system will be

active for a period of time when the

Voice Recognition system has asked

for a customer response.

Pair phone

Setup

Select phone

Delete phone

Change priority

Bluetooth off

• The system can recognize single dig-

itsfrom zero to nine while number

greater than ten will not be recognized.

- Speak in a natural voice without

pausing between words.

- While receiving voice commands,

Phonebook

Add entry

By voice

• If the command is not recognized, the

system will announce "Pardon" or No

input voice signal from microphone.

(No response)

press the

button on the steer-

ing wheel remote controller to ter-

minate guidance. Voice command

will convert back to waiting mode

to allow the user to say a new voice

command.

By Phone

Change

Delete name

• The system shall cancel voice recogni-

tion mode in following cases : When

Call

By name

pressing the

cancel following the beep. When not

making a call and pressing the but-

button and saying

By number

ton. When voice recognition has failed

3 consecutive times.

4 112

Features of your vehicle

■

Information Display

Phone Setup

All Bluetooth^®related operations can be

performed by voice command or by man-

ual operation.

- By Voice Command:

Press button on the steering wheel

to activate voice recognition.

3) Select desired item by rotating the

TUNE knob, then push the knob.

• Pairing phone

Before using Bluetooth^®features, the

phone must be paired (registered) to the

audio system. Up to 5 phones can be

paired in the system.

- By Manual Operation:

1) Push the [TUNE] knob to enter

SETUP mode.

Note:

Before pairing a mobile phone, check

to see that the Bluetooth^®function in

your mobile phone is set to “ON”

state.

Note:

The pairing procedure of the phone

varies according to each phone

model. Before attempting to pair

phone, please see your phone’s

User’s Guide for instructions.

The Bluetooth^®icon appears on the

upper side of audio display when a

phone is connected.

2) Select “PHONE” item by rotating the

TUNE knob, then push the knob.

4 113

Features of your vehicle

®

Bluetooth device list. Then attempt

pairing on your phone

Note:

“My Phone” say

“Yes” to proceed, otherwise say “Back” or

“Cancel”

Once pairing with the phone is com-

pleted, there is no need to pair with

that phone again unless the phone is

deleted manually from the audio sys-

tem (refer “Deleting Phone” section)

or the vehicle’s information is

removed from the phone.

➉ After Pairing is completed, your phone

will start to transfer phone/contact list

to the audio system.

“Yes”

- This process may take from a few min-

utes to over 10 minutes depending on

the phone model and number of

entries in the phone/contact list.

“Ready for pairing...please use your

phone to connect to the system the

pairing pass key is 0000”

By Voice Recognition

✽ Tip

Press

➀ Press

➁ Say “Set Up”.

- The system replies with available

commands.

button.

Pair the device after searching for

Bluetooth devices in your mobile phone.

Once pairing is complete, you will hear

the following message.

button.

®

Beep~♪

- To skip the information message, press

again and then a beep is heard.

➂ Say “Pair Phone”.

“Setup”

“Pairing Complete”

“Setup” say

“Pair phone”, “Select phone”, “Delete

phone”, “Change priority” or “Bluetooth off”

➃ Say “Yes” to proceed.

➄ Say the name of your phone when

“Connection Complete”

prompted.

- Use any name to uniquely describe

your phone.

“Pair Phone”

“Pair Phone” say

“Yes” to proceed, otherwise say “Back” or

“Cancel”

®

➅ Bluetooth system will repeat the

name you stated.

➆ Say "Yes" to confirm.

“Yes”

➇ The audio displays “searching

passkey: 0000” and asks you to initiate

pairing procedure from the phone.

----

“Please say a name for the phone”

Ex: “My phone” or “John”

®

➈ Search the Bluetooth system on your

phone .Your phone should display

your [vehicle model name] on the

4 114

Features of your vehicle

• Connecting phone

®

When the Bluetooth system is enabled,

• Deleting Phone

The paired phone can be deleted.

By Manual operation

the phone previously used is automati-

cally selected and re-connected. If you

want to select different phone previously

paired, the phone can be selected

through “Select Phone” menu.

- When the phone is deleted, all the infor-

mation associated with that phone is

also be deleted (including phonebook).

- If you want to use the deleted phone

with the audio system again, pairing

procedure must be completed once

more.

Only a selected phone can be used with

the hands-free system at a time.

➀ Select “PAIR” in PHONE menu, then-

proceed from step 5.

By Voice Recognition

➀ Press

➁ Say "Set Up".

➂ Say "Select Phone" after prompt

- The system lists all the registered

phone names.

➃ Say the name or number of desired

phone from the list.

➄ Say "Yes" to confirm.

button.

➀ Press

➁ Say “Set Up”.

➂ Say “Delete Phone” after prompt.

- The system lists all the registered

phone names.

➃ Say the name or number of desired

phone from the list.

➄ Say “Yes” to confirm.

button.

Note:

Until the audio displays “Transfer

®

Complete”, Bluetooth hands-free fea-

ture may not be fully operational.

Note:

If the phone is paired to two or more

vehicles of the same model, i.e. both

vehicles are HMC TUCSON, some

®

By Manual operation

➀ Select “DELETE” in PHONE menu,

then select desired phone from the list.

phones may not handle Bluetooth

By Manual operation

➀ Select “SELECT” in PHONE menu,

then select desired phone from the list.

devices of that name correctly. In this

case, you may need to change the

name displayed on your phone from

TUCSON.

Refer to your phone’s User’s Guide, or

contact your cellular carrier or phone

manufacturer for instructions.

4 115

Features of your vehicle

■

Phone Book (In-Vehicle)

• Adding Entry

• Changing Priority

✽

NOTICE

When several phones are paired to the

audio system, the system attempts to

connect following order when the

- The system can recognize single digits

from zero to nine. Numbers that are

ten or greater cannot be recognized.

- You can enter each digit individually

or group digits together in preferred

string lengths.

- To speed up input, it is a good idea to

group all digits into a continuous

string.

Phone numbers and voice tags can be

registered. Entries registered in the

phone can also be transferred.

®

Bluetooth system is enabled:

1) “Priority” checked phone.

2) Previously connected phone

3) Gives up auto connection.

• Adding Entry by Voice

➀ Press button.

➁ Say "Phonebook".

- The system replies with all available

commands.

- To skip the information message,

- The display corresponding to each

operation appears on the screen as fol-

lows:

- Input operation example:

1. Say: “Nine, nine, five”

By Voice Recognition

➀ Press button.

➁ Say “Set Up”.

press

heard.

again and then a beep is

➂ Say “Change Priority” after prompt.

➟ Display: “995”

2. And say: “Seven, three, four”

➟ Display: “995734”

- The system lists all the registered

phone names.

➃ Say the name or number of desired

phone from the list.

➄ Say “Yes” to confirm.

➂ Say "Add Entry".

➃ Say "By Voice" to proceed.

➄ Say the name of the entry when

prompted.

➅ Say “Yes”to confirm.

➆ Say the phone number of that entry

when prompted.

➇ Say “Store” if phone number input is

finished.

By Manual operation

➀ Select “PRIORITY” in PHONE menu,

then select desired phone from the

list.

➈ Say a phone number type. “Home”,

“Work”, “Mobile”, “Other” or “Default” is

available.

➉ Say “Yes” to complete adding entry.

11

Say “Yes” to store additional location

for this contact, or say “Cancel” to fin-

ish the process.

4 116

Features of your vehicle

• Adding Entry by Phone

➀ Press button.

➁ Say "Phonebook".

➂ Say "Add Entry" after prompt.

➃ Say "By Phone" to proceed.

➄ Say “Yes” to confirm.

• Deleting Name

The registered names can be deleted.

• Direct Calling

➀ Press button.

➁ Sat the following command.

➀ Press button.

➁ Say “Phonebook”

➂ Say “Delete Name” after prompt.

➃ Say the name of the entry (voice tag)

➄ Say “Yes” to confirm.

- Call <John> : Connects the call to John.

- Call <John> on <Mobile> : Connects

the call to John’s mobile phone number.

- Call <John> at <Home> : Connects

the call to john’s home number.

➅ Your phone will start to transfer

phone/contact list to the audio system.

This process may take over 10 min-

utes depending on the phone model

and number of entries.

- Call <John> in <Office> : Connects

the call to John’s office number.

■

Making a Phone Call

• Calling by Name

A phone call can be made by speaking

names registered in the audio system.

➆ Wait till the audio displays “Transfer

Complete” message.

Note:

Calls can be immediately connected

to contacts who name or voice tag are

saved in the phonebook(or contacts).

➀ Press

➁ Say "Call".

button.

• Changing Name

The registered names can be modified.

➂ Say “Name” when prompted.

➃ Say desired name (in phonebook or

voice tag).

➀ Press button.

➁ Say “Phonebook”

➂ Say “Change Name” after prompt.

➃ Say the name of the entry (voice tag)

➄ Say “Yes” to confirm.

➄ Say desired location (phone number

type). Only stored locations can be

selected.

➅ Say “Yes” to confirm and make a call.

➅ Say new desired name.

✽ Tip

A shortcut to each of the following func-

tions is available:

➀ Say “Call Name”

4 117

Features of your vehicle

• Dialing by Number

■

Receiving a Phone Call

Talking on the Phone

A phone call can be made by dialing the

spoken numbers. The system can recog-

nize single digits from zero to nine.

When receiving a phone call, a ringtone

is audible from speakers and the audio

system changes into telephone mode.

When talking on the phone, “Active Calls”

message and the other party’s phone

number (if available) are displayed on the

audio.

➀ Press

➁ Say “Call”.

button.

When receiving a phone call, “Incoming”

message and incoming phone number

(if available) are displayed on the audio.

• To Mute the Microphone

➂ Say “Number” when prompted.

➃ Say desired phone numbers.

➄ Say “Dial” to complete the number and

- Press button on the steering wheel.

• To Finish a Call

• To Answer a Call:

- Press

button on the steering wheel.

make a call.

- Press button on the steering wheel.

• To Reject a Call:

✽

NOTICE

✽ Tip

- Press

• To Adjust Ring Volume:

button on the steering wheel.

In the following situations, you or the

other party may have difficulty hearing

each other:

1. Speaking at the same time, your voice

may not reach each other parties. (This

is not a malfunction.) Speak alternate-

ly with the other party on the phone.

A shortcut to each of the following func-

tions is available:

➀ Say “Dial Number”

- Use VOLUME buttons on the steering

wheel.

➁ Say “Dial <digit>”

• To Transfer a Call to the Phone (Secret

Call):

- Press and hold

button on the steer-

ing wheel until the audio system trans-

fers a call to the phone.

®

2. Keep the Bluetooth volume to a low

level. High-level volume may result in

distortion and echo.

3. When driving on a rough road.

4. When driving at high speeds.

5. When the window is open.

6. When the air conditioning vents are

facing the microphone.

7. When the sound of the air condition-

ing fan is loud.

4 118

Features of your vehicle

®

• Please refer to User’s Guide of your

phone for more detailed informa-

tions. To stop music, try stop music

by the phone and change audio

mode to different one. (e.g. FM, CD,

iPod, ...)

• LANGUAGE (Language of Bluetooth

voice recognition)

■

Using the head unit as Bluetooth

music

While in ADVANCED menu, press

“LANGUAGE”. To change the language,

select the desired language and press

the [ENTER] button.

The head unit supports A2DP (Audio

Advanced Distribution Profile) and AVRCP

(Audio Video Remote Control Profile).

Both profiles are available for listening to the

®

MP3 music via Bluetooth cellular phone

■

ADVANCED Menu

®

supporting above Bluetooth profiles.

To play MP3 music from the Bluetooth

• BT OFF

While in ADVANCED menu, press “BT

After pressing the [SETUP] button, press

the PHONE menu. while in PHONE

menu, press the “ADVANCED” menu to

®

OFF” to turn off the Bluetooth System.

cellular phone, press the [AUX] button

until “MP3 Play” is displayed on the LCD.

Then try playing music by phone.

®

make Bluetooth Phone settings.(The

ADVANCED menu may differ according to

audio specifications.)

®

When playing music from the Bluetooth

cellular phone, the head unit displays

MP3 MODE.

• IN VOL.

(Bluetooth call volume adjustments)

®

NOTE:

While in ADVANCED menu, press “IN

VOL.” Use the knob key to set the desired

volume and press the [ENTER] button.

• Not only MP3 files, all the sounds

that the phone supports can be

heard by the audio system.

®

• The Bluetooth cellular phones shall

• CONTACTS

(Automatic Phonebook download setting)

feature A2DP and AVRCP functions.

• Some A2DP and AVRCP Bluetooth

®

While in ADVANCED menu, press

“CONTACTS”. To automatically save the

contacts and call history in your mobile

phone each time you connect a mobile

device, press Yes. If you do not wish for

automatic download, press No.

cellular phones may not play music

through the head unit on first try.

Please try the below;

i.e : Menu➟Filemanager➟Music➟

Option➟Play via Bluetooth

4 119

Features of your vehicle

■

Key matrix

Class

No.

Connected

Normal mode BT SETUP menu

KEY

Paired H/P

Empty

Disconnected

Not Connecting

2nd Call

Outgoing Call

Incoming Call

Active Call

2nd call

Not Paired

Accept Call

1st Call:waiting 2nd Call:waiting

2nd Call:active 1st Call:active

-

SHORT

1

Transfer call:secret call

-

LONG

VR

Reject Call

End Call

SHORT

MODE Cancel MODE Cancel MODE Cancel MODE Cancel

2

Speaker

Adaptation

Speaker

Adaptation

LONG

-

[10sec]

(Only English)

SHORT

Active

-

3

LONG

Change

language

[10sec]

4 120

Features of your vehicle -> AUDIO SYSTEM for Your Hyundai Ix35 SUV First Generation (2009-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals