Get CONTROLS -> Integrated universal remote control Guide for Mini Cooper 2 Door First Generation (2001-2005)

INTEGRATED UNIVERSAL REMOTE CONTROL*

The concept

Checking compatibility

If this symbol is depicted on the

packaging or in the operating

instructions of the original control

device, it is safe to assume that the remote-

controlled system is compatible with the

The integrated universal remote control

takes the place of up to three different con-

trol devices for different radio-remote-con-

trolled systems such as gate openers and

household alarm systems. The integrated

universal remote control detects and learns integrated universal remote control.

the signal transmitted by the original con-

trol device.

If you have additional questions,

please consult your MINI center or

call 1-800-355-3515.

You can also visit these websites:

The signal of an original control device can

be programmed onto one of the three

memory buttons 1. The system in question

can then be operated by means of the pro-

grammed memory button 1. Signal trans-

mission is indicated by indicator lamp 2.

Programming

1 Memory buttons

2 Indicator lamp

HomeLink is a registered trademark owned

by Johnson Controls, Inc.<

If you decide to sell your vehicle one day, in

the interest of your own security, remem-

ber to delete the programs before the vehi-

cle leaves your possession, refer to page 84.

Fixed-code control device

1. Switch on the ignition

2. During initial operation: press and hold

both outer buttons 1 approx. 20 seconds

until indicator lamp 2 flashes. This clears

all three memory buttons 1

3. Hold the original control device approx.

2 to 8 in / 5 to 20 cm away from memory

buttons 1.

While programming is in progress

and before operating any pro-

grammed system by remote control using

the integrated universal remote control,

make sure that the movement area of the

system in question is clear of people, ani-

mals and inanimate obstructions, in order

to avoid possible injury or damage. Also

comply with the safety precautions issued

for the original control device.<

The required distance between the

control device and memory

buttons 1 may vary, depending on the

system of the original control device in

question.<

INTEGRATED UNIVERSAL REMOTE CONTROL*

4. Simultaneously press the command but- remains on for approx. two seconds, the

ton of the original control device and the original control device is equipped with an

4. Press the button on the receiver of the

target device. Once you have completed

step 4, you have approx. 30 seconds to

complete step 5

desired memory button 1 on the inte-

grated universal remote control. The

alternating-code system. In this case, the

memory buttons 1 are programmed as

indicator lamp 2 begins to flash slowly. described for an alternating-code control

5. Press the programmed memory

button 1 of the integrated universal

remote control three times.

Release both buttons when indicator

lamp 2 starts flashing rapidly. If indica-

tor lamp 2 does not start to flash rapidly

after approx. 15 seconds, change the dis-

tance between the two devices

device.<

Alternating-code control device

The corresponding memory button 1 is

now programmed with the signal of the

original control device.

You will need to refer to the operating

instructions of the system in question in

order to program the integrated universal

remote control. Read through the operat-

ing instructions for information on syn-

chronization.

Observe the following additional instruc-

tions when you program an alternating-

code control device:

5. Repeat steps 3 and 4 to program other

original control devices.

Consult your MINI Dealer if you have

any questions.<

The corresponding memory button 1 is

now programmed with the signal of the

original control device.

Deleting memory buttons

The system can be operated as soon as the

ignition is switched on.

It is not possible to delete individual mem-

ory buttons 1. To delete all three memory

buttons 1 at the same time, however, per-

form the following steps:

You will find programming easier if

you have the assistance of a second

person.<

If the system cannot be operated

after repeated attempts at program-

ming, check whether the original control

device is equipped with an alternating-

code system. You can either check the oper-

ating instructions of the original control

device for this information, or you can

press and hold down the programmed

memory button 1 of the integrated univer-

sal remote control. If indicator lamp 2 of

the integrated universal remote control

flashes rapidly for a brief period and then

Press and hold both outer buttons 1 of the

integrated universal remote control for

approx. 20 seconds until indicator lamp 2

flashes.

1. Park your vehicle within range of the

radio-remote-controlled device

2. Program the integrated universal

remote control as described above in the

section on fixed-code programming

3. Locate the button on the receiver of the

target device, for example on the upper

part of the drive

CONTROLS -> Integrated universal remote control for Your Mini Cooper 2 Door First Generation (2001-2005)

Related Topics

Popular Owner Manuals

Latest Owner Manuals