2014-2022 Mini One 2 Door CONTROLS -> Interior equipment User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

CONTROLS -> Interior equipment for Your Mini One 2 Door Third Generation (2014-2022)

Interior equipment
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Universal Integrated Re‐
mote Control
Concept
The integrated Universal Remote Control in the
interior mirror can operate up to 3 functions of
remote-controlled systems, such as garage
door drives or lighting systems. The Universal
Integrated Remote Control replaces up to 3 dif‐
ferent hand-held transmitters. To operate the
remote control, the buttons on the interior mir‐
ror must be programmed with the desired
functions. The hand-held transmitter for the
particular system is required in order to pro‐
gram the remote control.
Before selling the vehicle, delete the stored
functions for the sake of security.
Safety information
WARNING
Body parts can be jammed when operat‐
ing remote-controlled systems, e.g., the garage
door, using the integrated universal remote
control. There is a risk of injury or risk of prop‐
erty damage. Make sure that the area of move‐
ment of the respective system is clear during
programming and operation. Also follow the
safety instructions of the hand-held transmit‐
ter.◀
Compatibility
If this symbol is printed on the packag‐
ing or in the owner's manual of the sys‐
tem to be controlled, the system is gen‐
erally compatible with the Universal Integrated
Remote Control.
If you have any questions, please contact:
▷ A dealer’s service center or another quali‐
fied service center or repair shop.
▷ on the Internet.
HomeLink is a registered trademark of Gentex
Corporation.
Overview
1 LED
2 Programmable keys
3 Hand-held transmitters of the system
Programming
General information
1. Switch on the ignition.
2. Initial setup:
Press and hold the two outer buttons on
the interior mirror simultaneously for ap‐
Seite 153
Interior equipment
CONTROLS
153
Online Edition for Part no. 01 40 2 915 044 - X/16
proximately 20 seconds until the LED on
the interior mirror flashes. This erases all
programming of the buttons on the interior
mirror.
3. Hold the hand-held transmitter for the sys‐
tem to be controlled approx. 1 to 3 in‐
ches/2.5 to 8 cm away from the buttons of
the interior mirror. The required distance
depends on the hand-held transmitter.
4. Simultaneously press and hold the button
of the desired function on the hand-held
transmitter and the button to be program‐
med on the interior mirror. The LED on the
interior mirror will begin flashing slowly.
5. Release both buttons as soon as the LED
flashes more rapidly. The LED flashing
faster indicates that the button on the inte‐
rior mirror has been programmed.
If the LED does not flash faster after at least
60 seconds, change the distance between
the interior mirror and the hand-held trans‐
mitter and repeat the step. Several more
attempts at different distances may be nec‐
essary. Wait at least 15 seconds between
attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior mirror button and repeat‐
edly press and release the hand-held trans‐
mitter button for 2 seconds.
6. To program other functions on other but‐
tons, repeat steps 3 to 5.
The systems can be controlled using the interior
mirror buttons.
Special feature of the rolling code
wireless system
If you are unable to operate the system after
repeated programming, please check if the sys‐
tem to be controlled features a rolling code ra‐
dio system.
Read the system's owner's manual, or press the
programmed button on the interior mirror lon‐
ger. If the LED on the interior mirror starts
flashing rapidly and then stays lit constantly for
2 seconds, the system features a rolling code
radio system. Flashing and continuous illumina‐
tion of the LED will repeat for approximately
20 seconds.
For systems with a rolling code radio system,
the Universal Integrated Remote Control and
the system also have to be synchronized.
Please read the owner's manual to find out
how to synchronize the system.
Synchronizing is easier with the aid of a second
person.
Synchronizing the universal remote control
with the system:
1. Park the vehicle within range of the re‐
mote-controlled system.
2. Program the relevant button on the interior
mirror as described.
3. Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.
4. Hold down the programmed button on the
interior mirror for approximately 3 seconds
and then release it. If necessary, repeat this
step up to three times in order to finish syn‐
chronization. Once synchronization is com‐
plete, the programmed function will be car‐
ried out.
Reprogramming individual buttons
1.
Switch on the ignition.
2. Press and hold the interior mirror button to
be programmed.
3. As soon as the interior mirror LED starts
flashing slowly, hold the hand-held trans‐
mitter for the system to be controlled ap‐
prox. 1 to 3 inches/2.5 to 8 cm away from
the buttons of the interior mirror. The re‐
quired distance depends on the hand-held
transmitter.
Seite 154
CONTROLS
Interior equipment
154
Online Edition for Part no. 01 40 2 915 044 - X/16
4. Likewise, press and hold the button of the
desired function on the hand-held trans‐
mitter.
5. Release both buttons as soon as the interior
mirror LED flashes more rapidly. The LED
flashing faster indicates that the button on
the interior mirror has been programmed.
The system can then be controlled by the
button on the interior mirror.
If the LED does not flash faster after at most
60 seconds, change the distance and re‐
peat the programming starting with step 4.
Several more attempts at different distan‐
ces may be necessary. Wait at least 15 sec‐
onds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior mirror button and repeat‐
edly press and release the hand-held trans‐
mitter button for 2 seconds.
Operation
WARNING
Body parts can be jammed when operat‐
ing remote-controlled systems, e.g., the garage
door, using the integrated universal remote
control. There is a risk of injury or risk of prop‐
erty damage. Make sure that the area of move‐
ment of the respective system is clear during
programming and operation. Also follow the
safety instructions of the hand-held transmit‐
ter.◀
The system, such as the garage door, can be
operated using the button on the interior mir‐
ror while the engine is running or when the ig‐
nition is started. To do this, hold down the but‐
ton within receiving range of the system until
the function is activated. The interior mirror
LED stays lit while the wireless signal is being
transmitted.
Deleting stored functions
Press and hold the two outer buttons on the in‐
terior mirror simultaneously for approximately
20 seconds until the LED on the interior mirror
flashes rapidly. All stored functions will be de‐
leted. The functions cannot be deleted individ‐
ually.
Digital compass
Overview
1 Control button
2 Mirror display
Mirror display
The point of the compass is displayed in the
mirror when driving straight.
Operating concept
Various functions can be called up by pressing
the control button with a pointed object, such
as the tip of a ballpoint pen or similar object.
The following setting options are displayed in
succession, depending on how long the control
button is pressed:
▷ Pressed briefly: turns display on/off.
▷ 3 to 6 seconds: compass zone setting.
▷ 6 to 9 seconds: compass calibration.
▷ 9 to 12 seconds: left/right-hand steering
setting.
▷ 12 to 15 seconds: language setting.
Seite 155
Interior equipment
CONTROLS
155
Online Edition for Part no. 01 40 2 915 044 - X/16
Setting the compass zones
Sets the particular compass zones on the vehi‐
cle so that the compass operates correctly; re‐
fer to World map with compass zones.
World map with magnetic zones
Procedure
1. Press and hold the control button for ap‐
prox. 3 to 4 seconds. The number of the set
compass zone appears in the mirror.
2. To change the zone setting, press the con‐
trol button quickly and repeatedly until the
number of the compass zone that corre‐
sponds with your location appears in the
mirror.
The set zone is stored automatically. The com‐
pass is ready for use again after approximately
10 seconds.
Calibrating the digital compass
The digital compass must be calibrated in the
event of the following:
▷ The wrong compass point is displayed.
▷ The point of the compass displayed does
not change despite changing the direction
of travel.
▷ Not all points of the compass are displayed.
Procedure
1. Make sure that there are no large metallic
objects or overhead power lines near the
vehicle and that there is sufficient room to
drive around in a circle.
2. Set the currently applicable compass zone.
3. Press and hold the control button for ap‐
prox. 6 to 7 seconds so that "C" appears on
the display. Next, drive in a complete circle
at least once at a speed of no more than
4 mph/7 km/h. If calibration is successful,
the "C" is replaced by the points of the
compass.
Seite 156
CONTROLS
Interior equipment
156
Online Edition for Part no. 01 40 2 915 044 - X/16
Left/right-hand steering
The digital compass is already set for right or
left-hand steering at the factory.
Setting the language
Press and hold the control button for approx.
12 to 13 seconds. Briefly press the control but‐
ton again to switch between English "E" and
German "O".
Settings are stored automatically after approxi‐
mately 10 seconds.
Sun visor
Glare shield
To provide protection against glare, fold the
sun visor down or pivot it to the side.
Vanity mirror
A vanity mirror is located in the sun visor be‐
hind a cover.
When the cover is opened, the mirror lighting
switches on.
Ashtray/cigarette
lighter
Overview
The ashtray is located in one of the frontal cup
holders, the cigarette lighter above it in the
center console.
Ashtray
In order to empty the ashtray, remove the ash‐
tray from the cup holder.
Lighter
WARNING
Contact with hot heating elements or the
hot socket of the cigarette lighter can cause
burns. Flammable materials can ignite if the
cigarette lighter falls down or is held against
the respective objects. There is a risk of fire and
injuries. Hold the cigarette lighter by its handle.
Make sure that children do not use the lighter
and burn themselves.◀
NOTE
If metal objects fall into the socket, they
can cause a short circuit. There is a risk of prop‐
erty damage. Replace the cigarette lighter or
socket cover again after using the socket.◀
Push in the lighter.
The lighter can be removed as
soon as it pops back out.
Sockets
Concept
The lighter socket can be used as a socket for
electrical equipment while the ignition is
switched on or the engine is running.
General information
The total load of all sockets must not exceed
140 watts at 12 volts.
Do not damage the socket by using non-com‐
patible connectors.
Seite 157
Interior equipment
CONTROLS
157
Online Edition for Part no. 01 40 2 915 044 - X/16
Safety information
WARNING
Devices and cables in the unfolding area
of the airbags, for example portable navigation
devices, etc., can hinder the unfolding of the
airbag or be thrown around in the car's interior
when unfolding. There is risk of injuries. make
sure that devices and cables are not in the air‐
bag's area of unfolding.◀
NOTE
Battery chargers for the vehicle battery
can work with high voltages and currents,
which means that the 12 volt on-board net‐
work can be overloaded or damaged. There is a
risk of property damage. Only connect battery
chargers for the vehicle battery to the starting
aid terminals in the engine compartment.◀
NOTE
If metal objects fall into the socket, they
can cause a short circuit. There is a risk of prop‐
erty damage. Replace the cigarette lighter or
socket cover again after using the socket.◀
In the center console
Remove the cover or cigarette lighter.
In the cargo area
The socket is located on the right side in the
cargo area.
USB interface/AUX-IN port
The concept
Mobile devices with USB port can be connected
to the USB interface.
A mobile audio device, e.g. a MP3 player, can
be connected using the AUX-IN port.
General information
The following devices can be connected:
▷ Mobile phones supported by the USB inter‐
face.
▷ Audio devices with USB port, for example
MP3 player.
▷ USB storage devices.
Common file systems are supported. FAT32
and exFAT are the recommended formats.
Information about compatible USB devices can
be found at
The following applications are possible:
▷ Exporting and importing profiles, refer to
page 41.
▷ Playing music files via USB audio.
▷ Adding music files to the music collection
and saving the music collection.
▷ Playing video films via USB video.
▷ Loading of software updates.
Seite 158
CONTROLS
Interior equipment
158
Online Edition for Part no. 01 40 2 915 044 - X/16
Overview
The USB interface and the AUX-IN port are lo‐
cated in the center armrest.
Connecting an external device
Observe the following when connecting:
▷ Do not use force when plugging the con‐
nector into the USB interface.
▷ Use a flexible adapter cable.
▷ Protect the USB storage device against me‐
chanical damage.
▷ Due to the large number of USB media
available on the market, it cannot be guar‐
anteed that every device is operable on the
vehicle.
▷ Do not expose USB media to extreme envi‐
ronmental conditions, such as very high
temperatures; refer to the device owner's
manual.
▷ Due to the many different compression
techniques, proper playback of the media
stored on the USB storage device cannot be
guaranteed in all cases.
▷ A connected USB storage device will be
supplied with charging current via the USB
interface if the device supports this.
▷ To ensure proper transmission of the stored
data, do not charge a USB storage device
via the onboard socket, when it is con‐
nected to the USB interface.
▷ Depending on how the USB storage device
should be used, settings may be required
on the USB storage device, refer to the de‐
vice owner's manual.
Not compatible USB media:
▷ USB hard drives.
▷ USB hubs.
▷ USB memory card readers with multiple in‐
serts.
▷ HFS-formatted USB media.
▷ MTP devices.
▷ Devices such as fans or lights.
Seite 159
Interior equipment
CONTROLS
159
Online Edition for Part no. 01 40 2 915 044 - X/16

Related Topics

CONTROLS
Opening and closing Settings Transporting children safely Driving Displays Lights Safety Driving stability control systems Driving comfort Climate control Storage compartments Cargo area

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot