Get Instruments and controls Guide for Nissan Leaf 4 Door First Generation (2010-2017)

2 Instruments and controls

Cockpit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Instrument panel. . . . . . . . . . . . . . . . . . . . . . . .2-4

Meters and gauges . . . . . . . . . . . . . . . . . . . . . .2-5

Speedometer and odometer. . . . . . . . . . . . . . .2-6

Li-ion battery temperature gauge . . . . . . . . . . . .2-7

Power meter . . . . . . . . . . . . . . . . . . . . . . . .2-7

Driving range. . . . . . . . . . . . . . . . . . . . . . . .2-8

Li-ion battery available charge gauge . . . . . . . . .2-9

Li-ion battery capacity level gauge . . . . . . . . . .2-10

Outside air temperature . . . . . . . . . . . . . . . .2-10

ECO indicator . . . . . . . . . . . . . . . . . . . . . .2-10

Clock . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

Warning/indicator lights and audible reminders. . . . .2-12

Checking bulbs . . . . . . . . . . . . . . . . . . . . .2-13

Warning lights . . . . . . . . . . . . . . . . . . . . . .2-13

Indicator lights . . . . . . . . . . . . . . . . . . . . . .2-19

Audible reminders . . . . . . . . . . . . . . . . . . . .2-21

Vehicle information display . . . . . . . . . . . . . . . . .2-22

Indicators for operation . . . . . . . . . . . . . . . . .2-23

Trip computer . . . . . . . . . . . . . . . . . . . . . .2-27

Warning information displays . . . . . . . . . . . . .2-32

Indicators for maintenance . . . . . . . . . . . . . . .2-34

Indicator for timer . . . . . . . . . . . . . . . . . . . .2-35

Security systems . . . . . . . . . . . . . . . . . . . . . .2-35

Vehicle security system. . . . . . . . . . . . . . . . .2-35

NISSAN Vehicle Immobilizer System . . . . . . . . .2-37

Windshield wiper and washer switch. . . . . . . . . . .2-38

Washer operation . . . . . . . . . . . . . . . . . . . .2-39

Rear window wiper and washer switch . . . . . . . . .2-40

Rear window and outside mirror defroster switch . . .2-41

Instrument brightness control . . . . . . . . . . . . . . .2-41

Headlight and turn signal switch . . . . . . . . . . . . .2-42

Headlight switch. . . . . . . . . . . . . . . . . . . . .2-42

Turn signal switch . . . . . . . . . . . . . . . . . . . .2-44

Fog light switch (if so equipped) . . . . . . . . . . . . .2-44

Heated steering wheel switch . . . . . . . . . . . . . . .2-45

Horn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-46

ECO switch . . . . . . . . . . . . . . . . . . . . . . . . .2-46

Heated seat switch . . . . . . . . . . . . . . . . . . . . .2-46

Vehicle Dynamic Control (VDC) OFF switch . . . . . .2-48

Charge port lid switch . . . . . . . . . . . . . . . . . . .2-48

Charge connector lock switch. . . . . . . . . . . . . . .2-49

Charge timer OFF switch . . . . . . . . . . . . . . . . .2-49

Power outlet . . . . . . . . . . . . . . . . . . . . . . . . .2-49

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-50

Cup holders . . . . . . . . . . . . . . . . . . . . . . .2-50

Seatback Pocket . . . . . . . . . . . . . . . . . . . .2-51

Sunglasses holder. . . . . . . . . . . . . . . . . . . .2-51

Glove box. . . . . . . . . . . . . . . . . . . . . . . . .2-52

Console box . . . . . . . . . . . . . . . . . . . . . . .2-52

Tonneau cover (if so equipped) . . . . . . . . . . . .2-53

Stowing golf bags. . . . . . . . . . . . . . . . . . . .2-54

Luggage side hook . . . . . . . . . . . . . . . . . . .2-54

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . .2-55

Power windows . . . . . . . . . . . . . . . . . . . . .2-55

Interior lights . . . . . . . . . . . . . . . . . . . . . . . . .2-57

Map lights . . . . . . . . . . . . . . . . . . . . . . . .2-57

Ceiling light. . . . . . . . . . . . . . . . . . . . . . . .2-58

Cargo light . . . . . . . . . . . . . . . . . . . . . . . .2-58

HomeLink® universal transceiver (if so equipped) . . .2-59

Programming HomeLink® . . . . . . . . . . . . . . .2-59

Programming HomeLink® for Canadian customers

and gate openers . . . . . . . . . . . . . . . . . . . .2-61

Operating the HomeLink® universal transceiver . .2-61

Programming trouble-diagnosis . . . . . . . . . . . .2-61

Clearing the programmed information . . . . . . . .2-62

Reprogramming a single HomeLink® button . . . .2-62

If your vehicle is stolen . . . . . . . . . . . . . . . . .2-62

COCKPIT

— Bluetooth® Hands-Free Phone System

control

6. Steering wheel

— Electric power steering system

— Horn

— Driver’s supplemental air bag

7. Wiper and washer switch

8. Steering-wheel-mounted controls (right

side)

— Cruise control switches

— ECO button (if so equipped)

9. Fuse box cover

10. Heated steering wheel

11. Vehicle Dynamic Control (VDC) OFF

switch

12. Charge timer OFF switch

13. Charge connector lock switch

14. Charge port lid opener switch

15. Tilting steering wheel lever

16. Heated seat switch

17. Shift lever

18. Storage tray

1. TRIP switch for twin trip odometer

2. Trip computer switch

3. Instrument brightness control switch

4. Headlight, fog light (if so equipped) and turn

signal switch

— Fog light (if so equipped)

5. Steering-wheel-mounted controls (left side)

(See LEAF Navigation System Owner’s

Manual.)

—

Driving range button (if so

— Headlight

equipped)

— Turn signal light

— Audio control

Instruments and controls 2-3

INSTRUMENT PANEL

10. iPod® connector/USB connector (See

LEAF Navigation System Owner’s Manual.)

11. Power outlet

12. Auxiliary input jack (See LEAF Navigation

System Owner’s Manual.)

13. Front passenger air bag status light/

Approaching Vehicle Sound for Pedestri-

ans (VSP) system warning light

14. Heater and air conditioner control

15. Glove box

1. Side ventilator

— Audio system

2. Meters and gauges

4. Hazard warning flasher switch

5. Center ventilator

6. Rear window defroster switch

7. Front passenger supplemental air bag

8. Hood release handle

3. Center multi-function control panel (See

LEAF Navigation System Owner’s Manual.)

— Navigation system

— Vehicle information and setting buttons

— Bluetooth® Hands-Free Phone System

9. Power switch

2-4 Instruments and controls

METERS AND GAUGES

— Shift position indicator

— Indicator for timer

13. Driving range

14. Li-ion battery available charge gauge

15. Li-ion battery capacity level gauge

1. Master warning lights

2. ECO indicator

8. Warning/Indicator lights

9. Power meter

3. Speedometer

10. ECO indicator

4. Clock

11. READY to drive indicator light

12. Vehicle information display

— Odometer/twin trip odometer

— Trip computer

5. Outside air temperature

6. Turn signal/Hazard indicator light

7. Li-ion battery temperature gauge

Instruments and controls 2-5

Changing the display:

3

Pushing the TRIP switch

located on the left

᭺

side of the combination meter panel changes the

display as follows:

TRIP A → TRIP B → TRIP A

For information about the vehicle information dis-

play, see “Vehicle information display”in this sec-

tion.

Resetting the trip odometer:

3

Pushing the TRIP switch

second resets the trip odometer to zero.

for approximately 1

᭺

SPEEDOMETER AND ODOMETER

Speedometer

The speedometer indicates the vehicle speed in

miles per hour (MPH) or kilometers per hour

(km/h).

Odometer/twin trip odometer

1

2

The odometer

and twin trip odometer

are

᭺

displayed on the vehicle information display when

the power switch is in the ON or READY to drive

position.

The odometer records the total distance the ve-

hicle has been driven.

The twin trip odometer records the distance of

individual trips.

2-6 Instruments and controls

NOTE:

• If the display indicates that the tempera-

ture of the Li-ion battery is near the red

zone end of the normal range, reduce ve-

hicle speed to decrease the temperature.

If the indicator is over the normal range,

the power provided to the traction motor

is reduced when the power limitation in-

dicator light is illuminated. Therefore the

vehicle is not as responsive when the ac-

celerator is depressed while the power

limitation light is illuminated. See “Power

limitation indicator light” in this section.

• If the outside temperature is extremely

low, the Li-ion temperature gauge may not

display a temperature reading. The ve-

hicle may not be able to be put in the

READY to drive mode. Contact a NISSAN

certified LEAF dealer.

LI-ION BATTERY TEMPERATURE

GAUGE

The gauge indicates the temperature of the Li-ion

battery.

POWER METER

This meter displays the actual traction motor

power consumption

brake power provided to the Li-ion battery

A

and the regenerative

᭺

B

.

᭺

1

The white dot

in the display moves right or left

The temperature of the Li-ion battery is within the

normal range when the display is within the zone

᭺

depending on demand.

1

shown in the illustration.

᭺

The white dot moves to the right when power is

provided to the traction motor (Li-ion battery dis-

charges).

The temperature of the Li-ion battery varies ac-

cording to the outside air temperature and driving

conditions.

The white dot moves to the left when power is

generated and provided to the Li-ion battery by

Instruments and controls 2-7

the regenerative brake system (Li-ion battery

charging).

NOTE:

• The driving range display will flash when

the low battery charge warning light illu-

minates. Additionally, if you continue to

drive the vehicle in this state and the Li-

ion battery is close to being completely

discharged, “---” will be displayed. Charge

the Li-ion battery as soon as possible.

When the Li-ion battery is charged, the

original display will be restored.

The power meter also indicates if the power

provided to the motor is limited or if regenerative

braking is limited. When power or regenerative

braking is limited, the circles on the display

2

change from a double circle to a single circle

.

᭺

Regenerative braking is automatically reduced

when the Li-ion battery is fully charged to prevent

the Li-ion battery from becoming overcharged.

Regenerative braking is also automatically re-

duced when the Li-ion battery temperature is

high/low (indicated by the red/blue zones on the

Li-ion battery temperature gauge) to prevent Li-

ion battery damage.

• After the vehicle is charged, the displayed

driving range is calculated based on the

actual average energy consumption of the

previous driving. The displayed driving

range will vary every time the vehicle is

fully charged.

DRIVING RANGE

1

The driving range

᭺

(miles or km) provides an

The more regenerative braking is reduced the

more double circles change to single circles

estimated distance that the vehicle can be driven

before recharging is necessary. The driving range

is constantly being calculated, based on the

amount of available Li-ion battery charge and the

actual power consumption average.

• The driving range will increases or de-

creases when the air conditioner, heater

or Li-ion battery warmer is turned on or

off, or the vehicle is shifted between D

(Drive) and ECO, or when any other acces-

sory is turned on or off based on driving.

If the Li-ion battery charge is low, power provided

to the traction motor is reduced. Motor output is

also limited if the Li-ion battery temperature is

high/low (indicated by the red/blue zones on the

Li-ion battery temperature gauge) or the Li-ion

battery charge level is low.

The more power provided to the traction motor is

reduced the more double circles change to

single circles.

2-8 Instruments and controls

light illuminated, there is a very small reserve of

Li-ion battery charge remaining.

tery available charge gauge illuminate be-

cause the remaining energy is a lower

percentage of the Li-ion battery’s capabil-

ity of storing power.

NOTE:

• The number of segments illuminated on

the Li-ion battery available charge gauge

is determined by the available charge and

the amount of charge the Li-ion battery is

capable of storing at the current tempera-

ture.

• Temperature affects the amount of charge

the Li-ion battery is capable of storing.

The Li-ion battery is capable of storing

less power when the Li-ion battery tem-

perature is cold. The Li-ion battery is ca-

pable of storing more power when the

Li-ion battery is warm. The number of seg-

ments illuminated on the Li-ion battery

available charge gauge can change based

on the amount of power the Li-ion battery

is capable of storing. For example, when

the Li-ion battery becomes colder, more

segments on the Li-ion battery available

charge gauge illuminate because the

available charge is a greater percentage

of the Li-ion battery’s capability of storing

power. When the Li-ion battery becomes

warmer, less segments on the Li-ion bat-

LI-ION BATTERY AVAILABLE

CHARGE GAUGE

1

The gauge

indicates the approximate avail-

᭺

able Li-ion battery charge to run the vehicle.

Charge the Li-ion battery before the display

reaches the bottom line.

The low battery charge warning light

illu-

minates when the Li-ion battery available charge

gauge is getting low. Charge as soon as it is

convenient, preferably before the display reaches

the bottom line. When the display reaches the

bottom of the display and the low battery charge

Instruments and controls 2-9

LI-ION BATTERY CAPACITY LEVEL

GAUGE

This gauge indicates the amount of charge the

Li-ion battery is capable of storing.

OUTSIDE AIR TEMPERATURE

The outside air temperature is displayed in °F or

°C.

ECO INDICATOR

The ECO indicator displays how economically

the vehicle is being operated.

The display may differ from the actual outside

temperature displayed on various signs or bill-

boards.

The meter display is affected by the following

conditions:

When the capacity of the Li-ion battery de-

creases with age and usage, the level of the

gauge will also decrease.

• Accelerator pedal operation.

• Brake pedal operation.

• Driving conditions.

• Traffic conditions.

• Heater and air conditioner usage.

2-10 Instruments and controls

• Time the vehicle is not moving while the vehicle

is in the READY to drive mode and accessories

are on.

NOTE:

This clock is not synchronized with the

clock displayed on the navigation system

screen. The charging timer starts and stops

charging base on the time displayed on the

navigation system screen. See LEAF Navi-

gation System Owner’s Manual.

Instant ECO driving level

1

The instant ECO driving level

is displayed by

᭺

the number of bars that increase (more economi-

cal driving) or decrease (less economical driving)

depending on vehicle operation.

Long term ECO driving level

Long term ECO driving is indicated by ECO

TREE symbols. The longer the vehicle is operated

economically, the more segments of the large

2

ECO TREE symbol

the segments of the large ECO TREE symbol are

displayed, a small ECO TREE indicator

are displayed. When all of

᭺

CLOCK

3

is also

Adjust the clock on the setting screen of the

vehicle information display. See “Settings” in this

section.

᭺

displayed, and the large ECO TREE symbol dis-

play is reset. The longer the vehicle is operated

economically, the more small ECO TREE sym-

bols are displayed. The ECO TREE symbols that

were illuminated while driving will turn off when

the vehicle power is turned off. The ECO TREE

symbols are stored in the navigation system to

show long term efficient vehicle operation.

If the power supply (12-volt battery) is discon-

nected, the clock will not indicate the correct

time. Readjust the time.

To increase the ECO driving level and for information

about driving the vehicle efficiently, see “Improve

driving range” in the “EV overview” section.

Instruments and controls 2-11

WARNING/INDICATOR LIGHTS AND

AUDIBLE REMINDERS

12-volt battery charge warning light

Low tire pressure warning light

Master warning light (red/yellow)

High beam indicator light

Plug in indicator light

Anti-lock Braking System (ABS) warning light

Approaching Vehicle Sound for Pedestrians

(VSP) system warning light

Power steering warning light

Seat belt warning light

Power limitation indicator light

READY to drive indicator light

BRAKE system warning light (yellow)

BRAKE warning light (red)

Supplemental air bag warning light

Security indicator light

Electric shift control system warning light

EV system warning light

Vehicle Dynamic Control (VDC) warning light

Exterior light indicator

Turn signal/hazard indicator lights

Vehicle Dynamic Control (VDC) off indicator

light

2-12 Instruments and controls

Headlight warning light

Front fog light indicator light (if so equipped)

Front passenger air bag status light

Low battery charge warning light

parking brake”. When these messages flash, im-

mediately stop the vehicle in a safe location, pull

the parking brake switch and push the P (Park)

position switch on the shift lever to place the

vehicle in the P (Park) position. The warning on

the meter and the chime stop when the parking

brake is operated or the vehicle is in the P (Park)

position. Contact a NISSAN certified LEAF

dealer for support.

CHECKING BULBS

WARNING LIGHTS

With all doors closed, apply the parking brake,

and push the power switch in the ON position.

The following lights will illuminate (if so

equipped):

12-volt battery charge

warning light

The DC/DC converter converts 400 volt Li-ion

battery voltage to charge the 12-volt battery.

,

This light illuminates continuously after the bulb is

checked when the power switch is in the ON

position, and turns off when the power switch is

placed in the READY to drive position.

The following lights illuminate briefly and then

turn off:

(yellow),

,

or

(red),

,

CAUTION

or

,

When this warning light illuminates, a chime

sounds and the following warnings are also dis-

played.

•

The DC/DC converter system may not

be functioning properly if the 12-volt

battery charge warning light illumi-

nates continuously when the power

switch is in the READY to drive posi-

tion. Immediately stop the vehicle in a

safe location and contact a NISSAN

certified LEAF dealer.

,

If any light does not illuminate, it may indicate a

burned-out bulb or an open circuit in the electri-

cal system. Have the system checked by a

NISSAN certified LEAF dealer.

• Master warning (red)

• EV system warning light

The following messages also flash on and off on

the vehicle information display.

Some indicators and warnings are also displayed

on the vehicle information display in the lower

display. (See “Vehicle information display” in this

section.)

If the vehicle is being driven: “Stop the vehicle”

and if the vehicle is stopped: “When parked apply

Instruments and controls 2-13

– If the 12-volt charge warning light con-

tinues to illuminate when the vehicle is

in the READY to drive mode, there may

be a malfunction in the DC/DC con-

Approaching Vehicle Sound

for Pedestrians (VSP) system

warning light

•

If the 12-volt warning light illuminates

continuously when the power switch is

in the READY to drive position. Do not

charge the 12-volt battery while this

warning light is illuminated. It may

lead to a malfunction of the DC/DC

converter system. Contact a NISSAN

certified LEAF dealer.

The Approaching Vehicle Sound for Pedestrians

(VSP) system warning light is located on the

instrument panel.

verter. Contact

a

NISSAN certified

LEAF dealer for inspection.

or

Anti-lock Braking

System (ABS)

warning light

This light comes on if there is a malfunction in the

VSP system.

NOTE:

If the VSP system warning light illuminates while

the power switch is in ON position, or in the

READY to drive position, it may indicate the VSP

system is not functioning properly. Have the sys-

tem checked by a NISSAN certified LEAF dealer.

• If the vehicle does not go into the READY

to drive position (when the power switch

is pushed with the brake pedal is de-

pressed), jump-start the vehicle to place

the power switch in the READY to drive

position. See “Jump starting” in the “In

case of emergency” section.

When the power switch is in the ON or READY to

drive position, the Anti-lock Braking System

(ABS) warning light illuminates and then turns off.

This indicates the ABS is operational.

If the ABS warning light illuminates while the

power switch is in READY to drive position, or

while driving, it may indicate the ABS is not

functioning properly. Have the system checked

by a NISSAN certified LEAF dealer.

See “Approaching Vehicle Sound for Pedestri-

ans (VSP) system” in the “EV overview” section.

• Do not jump-start the vehicle and contact

a

inspection:

BRAKE system warning light

(yellow)

NISSAN certified LEAF dealer for

– If the 12-volt charge warning light

turns off when the vehicle is in the

READY to drive mode, the 12-volt bat-

tery may be discharged or there may be

a malfunction in the 12-volt battery re-

lated system.

This light functions for both the cooperative re-

generative brake and the electronically driven

intelligent brake systems. When the power

If an ABS malfunction occurs, the anti-lock func-

tion is turned off. The brake system then operates

normally, but without anti-lock assistance. (See

“Brake system” in the “Starting and driving” sec-

tion.)

2-14 Instruments and controls

switch is placed in the ON position or in the

READY to drive position, the light remains illumi-

nated for about 2 or 3 seconds. If the light illumi-

nates at any other time, it may indicate that the

cooperative regenerative brake and/or the elec-

tronically driven intelligent brake systems are not

functioning properly. Have the system checked

by a NISSAN certified LEAF dealer. If the BRAKE

warning light (red) also illuminates, stop the ve-

hicle immediately and contact a NISSAN certified

LEAF dealer. For additional information, see

“Brake system” in the “Starting and driving” sec-

tion.

ing light illuminates, the Vehicle Dynamic Control

(VDC) warning light and the brake system warn-

ing light (yellow) also illuminate.

•

The cooperative regenerative brake

system may not be working properly if

the brake system warning light illumi-

nates when the READY to drive indica-

tor light is ON. If you judge it to be safe,

drive carefully to the nearest service

station for repairs. Otherwise, have

your vehicle towed because driving

could be dangerous.

If the light illuminates while the power switch is in

the READY to drive position with the parking

brake not applied, stop the vehicle and perform

the following items.

1. Check the brake fluid level. If brake fluid is

necessary, add fluid and have the system

checked by a NISSAN certified LEAF dealer.

See “Brake fluid” in the “Maintenance and

do-it-yourself” section.

or

BRAKE warning

light (red)

When the power switch is placed in the ON

position or in the READY to drive position, the

light remains illuminated for about a few seconds.

If the light illuminates at any other time, it may

indicate that the hydraulic brake system is not

functioning properly. If the BRAKE warning light

illuminates, stop the vehicle immediately and

contact a NISSAN certified LEAF dealer.

2. If the brake fluid level is correct, have the

warning system checked by a NISSAN certi-

fied LEAF dealer.

WARNING

•

Pressing the brake pedal when the

power switch position is not in the ON

or READY to drive position and/or low

brake fluid level may increase the

stopping distance and braking will re-

quire greater pedal effort as well as

pedal travel.

WARNING

•

Your brake system may not be working

properly if the warning light is on. Driv-

ing could be dangerous. If you judge

the brake system to be safe, drive care-

fully to the nearest service station for

repairs. Otherwise, have your vehicle

towed because driving it could be dan-

gerous.

Parking brake indicator:

•

If the brake fluid level is below the

minimum or MIN mark on the brake

fluid reservoir, do not drive until the

brake system has been checked at a

NISSAN certified LEAF dealer.

When the ignition switch is placed in the ON

position, the light comes on when the parking

brake is applied.

Low brake fluid warning light:

When the power switch is in the ON position, the

light warns of a low brake fluid level. If this warn-

Instruments and controls 2-15

NOTE:

EV system warning

light

This light illuminates if there is a malfunction in the

following systems. Contact a NISSAN certified

LEAF dealer.

•

Pressing the brake pedal when the

power switch position is not in the ON

or READY to drive position and/or low

brake fluid level may increase the

stopping distance and braking will re-

quire greater pedal effort as well as

pedal travel.

If the brake fluid level is below the

minimum or MIN mark on the brake

fluid reservoir, do not drive until the

brake system has been checked at a

NISSAN certified LEAF dealer.

The low battery charge warning light turns

off immediately before the Li-ion battery is

completely discharged and the vehicle will

stop. If the Li-ion battery becomes com-

pletely discharged, the vehicle must be

charged in order to be driven.

• Traction motor and inverter system

• Charge port or on board charger

• Li-ion battery system

Low tire pressure warning

light

• Cooling system

Your vehicle is equipped with a Tire Pressure

Monitoring System (TPMS) that monitors the tire

pressure of all tires.

• Shift control system

• Emergency shut off system is activated. See

“Emergency shut off system” in the “EV over-

view” section.

Electric shift control system

warning light

The low tire pressure warning light warns of low

tire pressure or indicates that the TPMS is not

functioning properly.

This light illuminates to warn when a malfunction

occurs in the electric shift control system. When

the master warning illuminates, the chime sounds

and the message, “When parked apply parking

brake”, is displayed on the vehicle information

display.

Headlight warning

light

This light illuminates if the LED headlights are

After the power switch is placed in the ON posi-

tion, this light illuminates for about 1 second and

then turns off.

malfunctioning. Contact

LEAF dealer.

a

NISSAN certified

Low tire pressure warning:

When the power switch is in the OFF position,

the chime sounds continuously. Make sure the

parking brake is applied.

Low battery charge warning

light

This light illuminates when the available Li-ion

battery charge is getting low. Charge as soon as

it is possible, preferably before the Li-ion battery

available charge gauge reaches the bottom line.

If the vehicle is being driven with low tire pres-

sure, the warning light will illuminate. A CHECK

TIRE PRESSURE warning also appears on the

vehicle information display.

Have the system checked by a NISSAN certified

LEAF dealer.

2-16 Instruments and controls

When the low tire pressure warning light illumi-

nates, you should stop and adjust the tire pres-

sure to the recommended COLD tire pressure

shown on the Tire and Loading Information label.

The low tire pressure warning light does not

automatically turn off when the tire pressure is

adjusted. After the tire is inflated to the recom-

mended pressure, the vehicle must be driven at

speeds above 16 MPH (25 km/h) to activate the

TPMS and turn off the low tire pressure warning

light. Use a tire pressure gauge to check the tire

pressure.

NISSAN certified LEAF dealer. The CHECK TIRE

PRESSURE warning does not appear if the low

tire pressure warning light illuminates to indicate

a TPMS malfunction.

and may lead to an accident and could

result in serious personal injury. Check

the tire pressure for all four tires. Ad-

just the tire pressure to the recom-

mended COLD tire pressure shown on

the Tire and Loading Information label

to turn the low tire pressure warning

light OFF. If the light still illuminates

while driving after adjusting the tire

pressure, a tire may be flat. If you have

a flat tire, repair it as soon as possible.

When a wheel is replaced, the TPMS

will not function and the low tire pres-

sure warning light will flash for ap-

proximately 1 minute. The light will re-

main on after 1 minute. Contact your

NISSAN certified LEAF dealer as soon

as possible for tire replacement

and/or system resetting.

For additional information, see “Vehicle informa-

tion display” and “Tire Pressure Monitoring Sys-

tem (TPMS)”in the “Starting and driving”section.

WARNING

•

Radio waves could adversely affect

electric medical equipment. Those

who use a pacemaker should contact

the electric medical equipment manu-

facturer for the possible influences be-

fore use.

•

The CHECK TIRE PRESSURE warning appears

each time the ignition switch is placed in the ON

position as long as the low tire pressure warning

light remains illuminated.

•

If the light does not illuminate when

the power switch is placed in the ON

position, have the vehicle checked by a

NISSAN certified LEAF dealer as soon

as possible.

If the light illuminates while driving,

avoid sudden steering maneuvers or

abrupt braking, reduce vehicle speed,

pull off the road to a safe location and

stop the vehicle as soon as possible.

Driving with under-inflated tires may

permanently damage the tires and in-

crease the likelihood of tire failure.

Serious vehicle damage could occur

For additional information, see “Vehicle informa-

tion display” in the “Instruments and Controls”

section and “Tire Pressure Monitoring System

(TPMS)” in the “Starting and driving” section and

“In case of emergency” section.

•

Replacing tires with those not origi-

nally specified by NISSAN could affect

the proper operation of the TPMS.

TPMS malfunction:

CAUTION

If the TPMS is not functioning properly, the low

tire pressure warning light will flash for approxi-

mately 1 minute when the power switch is placed

in the ON position. The light will remain on after

the 1 minute. Have the system checked by a

The TPMS is not a substitute for the

regular tire pressure check. Be sure to

check the tire pressure regularly.

Instruments and controls 2-17

switch is placed in the ON position, and will

remain illuminated until the driver’s seat belt is

fastened. At the same time, the chime will sound

for approximately 6 seconds unless the driver’s

seat belt is securely fastened.

Power steering warning light

•

If the vehicle is being driven at speeds

of less than 16 MPH (25 km/h), the

TPMS may not operate correctly.

Be sure to install the specified size of

tires to the four wheels correctly.

When the power switch is in the ON position, the

electric power steering warning light illuminates

and turn off when the power switch is placed in

the READY to drive position. This indicates the

electric power steering system is operational.

The seat belt warning light for the front passenger

will illuminate if the seat belt is not fastened when

the front passenger’s seat is occupied. The front

passenger seat belt warning light does not acti-

vate until 5 seconds after the power switch is in

the ON position.

Master warning light

(red/yellow)

If the electric power steering warning light illumi-

nates while the READY to drive indicator light is

ON, it may indicate the electric power steering

system is not functioning properly and may need

servicing. Have the electric power steering sys-

tem checked by a NISSAN certified LEAF dealer.

There are two types of master warning lights:

yellow and red. These lights illuminate if any

warning lights or indicator lights are illuminated or

if various vehicle information warnings appear in

the vehicle information display.

See “Seat belts”in the “Safety — Seats seat belts

and supplemental restraint system” section for

precautions on seat belt usage.

Yellow master warning light:

When the electric power steering warning light

illuminates while the READY to drive indicator is

ON, the power assist to the steering will cease

operation but you will still have control of the

vehicle. At this time, greater steering efforts are

required to operate the steering wheel, especially

in sharp turns and at low speeds.

The yellow master warning light is located on the

upper display.

Supplemental air bag warning

light

This light illuminates when a yellow warning light

on the lower display is illuminated or when a

message is displayed on the vehicle information

display.

After turning the power switch to the ON posi-

tion, the supplemental air bag warning light will

illuminate. The supplemental air bag warning light

will turn off after about 7 seconds if the supple-

mental front air bag and supplemental side air

bag, curtain side-impact air bag systems and/or

pretensioner seat belt are operational.

See “Power steering system” in the “Starting and

driving” section.

Red master warning light:

The red master warning light is located on the

upper display.

Seat belt warning light

If any of the following conditions occur, the front

air bag, side air bag, curtain air bag and preten-

sioner systems need servicing and your vehicle

This light illuminates when a red warning light on

the lower display is illuminated or when a warning

is displayed on the vehicle information display.

The light and chime remind you to fasten seat

belts. The light illuminates whenever the power

2-18 Instruments and controls

must be taken to your nearest NISSAN certified

LEAF dealer.

Vehicle Dynamic Control

(VDC) warning light

The light will blink when the Vehicle Dynamic

Control (VDC) system is operating, thus alerting

the driver that the vehicle is nearing its traction

limits. The road surface may be slippery.

Front fog light indicator

light (if so equipped)

• The supplemental air bag warning light remains

on after approximately 7 seconds.

The front fog light indicator light illuminates when

the front fog lights are on. See “Fog light switch”

in this section.

• The supplemental air bag warning light flashes

intermittently.

Front passenger air bag status

light

The front passenger air bag status light (located

on the center of the instrument panel) will be lit

and the passenger front air bag will be turned

OFF depending on how the front passenger seat

is being used.

• The supplemental air bag warning light does not

illuminate at all.

When the VDC warning light illuminates with

VDC system turned on, this light alerts the driver

to the fact that the VDC system’s fail-safe mode

is operating, for example the VDC system may

not be functioning properly. Have the system

checked by a NISSAN certified LEAF dealer. If a

malfunction occurs in the system, the VDC sys-

tem function will be canceled but the vehicle is

still driveable. For additional information, see “Ve-

hicle Dynamic Control (VDC) system” in the

“Starting and driving” section of this manual.

Unless checked and repaired, the Supplemental

Restraint Systems and/or the pretensioners may

not function properly.

For additional information, see “Supplemental re-

straint system” in the “Safety — Seats seat belts

and supplemental restraint system” section.

For front passenger air bag status light operation,

see “NISSAN Advanced Air Bag System (front

seats)” in the “Safety — Seats seat belts and

supplemental restraint system” section of this

manual.

WARNING

If the supplemental air bag warning light

is on, it could mean that the front air bag,

side air bag, curtain air bag and/or pre-

tensioner systems will not operate in an

accident. To help avoid injury to yourself

or others, have your vehicle checked by a

NISSAN certified LEAF dealer as soon as

possible.

INDICATOR LIGHTS

Exterior light indicator

High beam indicator light

(blue)

This light illuminates when the headlight high

beam is on and goes out when the low beam is

selected.

This indicator illuminates when the headlight

switch is turned to the AUTO (if so equipped),

or

position and the front parking

lights, side maker lights, tail and license plate

lights are on. The indicator turns off when these

lights are turned off.

Instruments and controls 2-19

• When the temperature of EV system is high

(motor, inverter, coolant system, Li-ion battery

etc.)

Plug in indicator light

WARNING

This light illuminates while charge connector is

connected to the vehicle and blinks during charg-

ing.

Power limitation mode can result in re-

duced power and vehicle speed. The re-

duced speed may be lower than other

traffic, which could increase the chance

of a collision. Be especially careful when

driving. If the vehicle cannot maintain a

safe driving speed, pull to the side of the

road in a safe area. Charge the Li-ion

battery if the charge is low or allow the

Li-ion battery to cool.

• When the EV system has a malfunction.

If the low battery charge warning light is illumi-

nated, charge the Li-ion battery as soon as pos-

sible.

NOTE:

If the charge connector is connected to the

vehicle, the power switch can not be placed

in the READY to drive position.

If this indicator illuminates because the Li-ion

battery is cold due to low outside temperatures,

move the vehicle to a warmer location. The Li-ion

battery temperature may be increased by charg-

ing the Li-ion battery.

Power limitation indicator light

READY to drive indicator light

When the power limitation indicator light is illu-

minated, the power provided to the traction motor

is reduced. Therefore the vehicle is not as re-

sponsive when the accelerator is depressed

while the power limitation light is illuminated.

If the light illuminates when the EV system be-

comes hot due to continuous hill climbing either

continue driving at a slower safe speed, or stop

the vehicle in a safe location. If this indicator does

not turn off, contact a NISSAN certified dealer.

The READY to drive indicator light illuminates

when the EV (Electric Vehicle) System is pow-

ered and the vehicle may be driven.

The READY to drive indicator light will turn off in

the following conditions.

When this light comes on, the warning display

appears on the navigation display and the vehicle

information display. Follow the instructions pro-

vided on the navigation display.

If the indicator illuminate when a part in the EV

system has malfunctioned. If the indicator illumi-

nates in a situation other than those described

above, or if it does not turn off, there may be a

system malfunction. Contact a NISSAN certified

LEAF dealer.

• Certain EV (Electric Vehicle) system malfunc-

tions.

• The READY to drive indicator light turns off

immediately before the Li-ion battery is com-

pletely discharged If the Li-ion battery becomes

completely discharged, the vehicle must be

charged in order to be driven. See “Low battery

charge warning light” in this section.

This light illuminates in the following conditions.

• Li-ion battery available charge is extremely low

• Li-ion battery temperature is very low (approxi-

mately −4°F (−20°C)

2-20 Instruments and controls

Make sure that the power switch is pushed to the

OFF position, and take the Intelligent Key with

you when leaving the vehicle.

Security indicator light

AUDIBLE REMINDERS

Brake pad wear warning

This light blinks when the power switch is in the

ACC, OFF or LOCK position. This function indi-

cates the security system equipped on the ve-

hicle is operational.

The disc brake pads have audible wear warnings.

When a brake pad requires replacement, it will

make a high pitched scraping sound when the

vehicle is in motion. This scraping sound will first

occur only when the brake pedal is depressed.

After more wear of the brake pad, the sound will

always be heard even if the brake pedal is not

depressed. Have the brakes checked as soon as

possible if the warning sound is heard.

Light reminder chime

The light reminder chime will sound when the

driver side door is opened with the light switch in

If the security system is malfunctioning, this light

will remain on while the power switch is in the ON

position. For additional information, see “Security

systems” in this section.

the

or

position, and the power

switch in the ACC, OFF or LOCK position.

Turn the light switch off when you leave the

vehicle.

Turn signal/hazard indicator

lights

This light flashes when the turn signal switch

lever or hazard switch is turned on.

Parking brake reminder chime

Electric shift control system reminder

chime

If an improper shift operation is performed, for

safety reasons a chime will sound and at the

same time, depending on the conditions, the

operation will be cancelled or the shift position

will switch to the N position.

A chime sounds if the parking brake is set and the

vehicle is driven. The chime will stop if the parking

brake is released or the vehicle speed returns to

zero.

Vehicle Dynamic Control

(VDC) off indicator light

This light illuminates when the Vehicle Dynamic

Control (VDC) switch is pushed to OFF. This

indicates that the VDC system is not operating.

See “Vehicle Dynamic Control (VDC) system” in

the “Starting and driving” section.

Power switch reminder chime (if so

equipped)

The power switch reminder chime will sound

when the driver’s door is opened while the power

switch is in the ON or READY position. Push the

power switch to the OFF position.

For more details, see “Driving vehicle” in the

“Starting and driving” section.

Key reminder chime

A chime will sound if the driver’s side door is

opened while the power switch is pushed to the

ON or ACC position.

Instruments and controls 2-21

VEHICLE INFORMATION DISPLAY

For the details about the NISSAN Intelligent

Key® system, see “NISSAN Intelligent Key®

system” in the “Pre-driving checks and adjust-

ments” section.

Seat belt warning chime

The seat belt warning chime will sound for about

6 seconds unless the driver’s seat belt is securely

fastened.

12-volt battery charge warning chime

If the 12-volt battery charge warning light illumi-

nates, the chime will sound when a warning mes-

sage is displayed on the vehicle information dis-

play on the lower display.

When the chime sounds, immediately stop the

vehicle in a safe location and push the P (Park)

position switch on the shift lever and apply park-

ing brake. The 12-volt battery charge warning

light turns off on the lower display and the chime

will stop when the parking brake is applied or the

vehicle is placed in the P (Park) position. Contact

a NISSAN certified LEAF dealer for support. For

details of the meter warnings, see “12-volt bat-

tery charge warning light” in this section.

1

The vehicle information display

is located in

᭺

the lower display, and it displays charging related

information, Average electricity consumption/

Instant electricity consumption, Average vehicle

speed, Driving distance/Driving time (Elapsed

time), shift position indicator, the cruise control,

the Intelligent Key operation information and

other warnings and information.

For details about the odometer, see “Odometer/

twin trip odometer” in this section.

For details about the cruise control, see “Cruise

control” in the “Starting and driving” section.

2-22 Instruments and controls

power switch is pressed with the brake pedal

depressed.

No key inside the vehicle:

INDICATORS FOR OPERATION

This warning appears when the door is closed

with the Intelligent Key left outside the vehicle

and the power switch in the ACC or ON position.

Make sure that the Intelligent Key is inside the

vehicle.

1. READY to drive position operation

indicator

This indicator appears while the vehicle is in the P

(Park) position. This indicator means that the EV

(Electric Vehicle) system will start when the

2. Key is not detected warning

This warning appears in either of the following

conditions.

Instruments and controls 2-23

Unregistered Intelligent Key:

If this indicator appears, touch the power switch

with the Intelligent Key while depressing the

brake pedal. (See “NISSAN Intelligent Key® bat-

tery discharge” in the “Starting and driving” sec-

tion.)

driven. However, contact a NISSAN certified

LEAF dealer.

This warning appears when the power switch is

placed in the ON, ACC or READY to drive posi-

tion and the Intelligent Key cannot be recognized

by the system. You cannot place the power

switch in the READY to drive position with an

unregistered key. Use an Intelligent Key that has

been registered.

7. Driver alert

This warning appears when the previously set

time for a break is reached. You can set the time

for up to 6 hours in the setting menu. (See “Trip

computer” in this section.)

5. Door/rear hatch open warning

(power switch is in the ON position)

This warning appears if any of the doors and/or

the rear hatch are open or not closed securely.

The vehicle icon indicates which door or the rear

hatch is open on the display. Make sure that all of

the doors and the rear hatch are closed.

8. Low outside air temperature

See “NISSAN Intelligent Key® system” in the

“Pre-driving checks and adjustments” section for

more details.

The outside air temperature is displayed in °F or

°C in the range of −20°F to 140°F (−30°C to

60°C).

3. Intelligent Key battery discharge

indicator

This indicator appears when the Intelligent Key

battery is running out of power.

The outside air temperature mode includes a low

temperature warning feature. If the outside air

temperature is below 37°F (3°C), the warning is

displayed on the screen.

This warning also appears alternating with SHIFT

ЉPЉ warning while the driver’s door is opened with

the shift position in any position other than the P

(Park) position. See “SHIFT ЉPЉ warning (if so

equipped)” in this section.

If this indicator appears, replace the battery with

a new one. (See “NISSAN Intelligent Key® bat-

tery replacement” in the “Maintenance and do-it-

yourself” section.)

The outside temperature sensor is located in

front side of the vehicle. The sensor may be

affected by road, wind directions and other driv-

ing conditions. The display may differ from the

actual outside temperature or the temperature

displayed on various signs of billboards.

6. Intelligent Key system warning

This warning appears if there is a malfunction in

the Intelligent Key system.

4. EV system operation for discharged

Intelligent Key system indicator

This indicator appears when the Intelligent Key

battery is running out of power and when the

Intelligent Key System and vehicle are not com-

municating normally.

If this warning appears while the power switch

position is in the ON position, the power switch

can not be switched to the READY to drive posi-

tion. If this warning appears while power switch is

in the READY to drive position, the vehicle can be

9. Low washer fluid warning (if so

equipped)

This warning appears when the washer tank fluid

is at a low level. Add washer fluid as necessary.

2-24 Instruments and controls

(See “Window washer fluid” in the “Maintenance

and do-it-yourself” section.)

This message appears when the parking brake is

not applied, even after the vehicle has been

parked. The master warning light (red) also illu-

minates and the chime sounds.

16. Li-ion battery low charge warning

This indicator appears when the Li-ion battery is

getting low. The low battery charge warning light

and the master warning light (yellow) also illumi-

nate. Charge the Li-ion battery as soon as pos-

sible. The [i] symbol is shown on the vehicle

information display, this indicates that further in-

formation is available on the navigation display.

Check the navigation display for further informa-

tion and instructions.

10. Light reminder warning

This warning appears when the power switch is

turned to the OFF position but the headlight

switch is still ON. Turn off the headlight switch.

Apply parking brake. The message in the vehicle

information display turns off and the chime stops.

Have the system checked by a NISSAN certified

LEAF dealer.

11. Plug in indicator

This indicator appears when the charge connec-

tor is connected.

14. Shift control system (T/M) warning

This warning appears if there is a malfunction in

the electric shift control system but operation of

the electric shift control is still possible. The mas-

ter warning (yellow) light also illuminates and the

chime sounds. When this occurs, check the shift

position indicator by the shift lever or vehicle

information display in the meter to make sure that

shifting has been performed properly. Contact a

NISSAN certified LEAF dealer as soon as pos-

sible.

17. Power limitation warning

If the charge connector is connected to the ve-

hicle, the power switch can not be placed in the

READY to drive position.

This display appears when the Li-ion battery ca-

pacity is getting too low to move the vehicle or if

there is any reason to limit traction power (Li-ion

battery low or high temperature etc.). The power

limitation indicator light and the master warning

light (yellow) also illuminate. The [i] symbol is

shown on the vehicle information display. This

indicates that further information is available on

the navigation display. Check the navigation dis-

play for further information and instructions.

12. Remove charge connector

warning

This warning appears when the power switch is

in the ACC or ON position and if the power

switch is pushed to the READY to drive position

with the brake pedal depressed, while the charge

connector is inserted to the vehicle. Remove the

charge connector.

15. Shift position warning

This warning appears if the system cannot detect

the shift position. Make sure the vehicle is placed

in a position properly.

18. DC/DC converter warning

13. Electric shift control system

warning

This message appears if there is malfunction in

the electric shift control system.

This warning appears if the DC/DC converter

system is not functioning properly. The 12-volt

battery charge warning (red) light also and the

master warning light illuminate. Stop the vehicle

The master warning light (red) also illuminates

and the chime sounds. Check the shift position of

the vehicle.

Instruments and controls 2-25

in a safe location and contact a NISSAN certified

LEAF dealer.

21. Cruise control indicator

Cruise main switch indicator:

23. SHIFT ЉPЉ warning (if so

equipped)

19. Apply parking brake warning

This warning appears alternating with door/rear

hatch open warning when the driver’s door is

opened with the shift position in any position

other than the P (Park) position. See “Door/rear

hatch open warning (power switch is in the ON

position)” in this section. If this warning appears,

push the P (Park) position switch and place in the

P (Park) position.

This indicator is displayed when the cruise con-

trol main switch is pushed. When the main switch

is pushed again, the indicator disappears. When

the cruise control main switch indicator is dis-

played, the cruise control system is operational.

This warning appears if the DC/DC converter

system is not functioning properly after the “Stop

the vehicle” message above. If this warning ap-

pears on the display, stop the vehicle in a safe

location and push the P (Park) position switch on

the shift lever. If the parking brake is applied, the

display turns off. Contact a NISSAN certified

LEAF dealer.

Cruise set switch indicator:

This indicator is displayed while the vehicle

speed is controlled by the cruise control system.

If the indicator blinks while the power switch is in

the READY to drive position, it may indicate that

the cruise control system is not functioning prop-

erly. Have the system checked by a NISSAN

certified LEAF dealer.

24. Intelligent Key error

20. Check tire pressure warning

After the ignition switch is pushed to the ON

position, this light comes on for about 2 seconds

and then turns off.

This warning appears when the low tire pressure

warning light in the meter illuminates and low tire

pressure is detected. The warning appears each

time the ignition switch is placed in the ON

position as long as the low tire pressure warning

light remains illuminated.

The I-Key System Error message warns of a

malfunction with the Intelligent Key system. If the

light comes on while the engine is stopped, it may

be impossible to start the engine.

See “Cruise control” in the “Starting and driving”

section for details.

22. Shift position indicator

If this warning appears, stop the vehicle and

adjust the tire pressure to the recommended

COLD tire pressure shown on the Tire and Load-

ing Information label. (See “Low tire pressure

warning light” in this section and “TIRE PRES-

SURE MONITORING SYSTEM (TPMS)” in the

“Starting and driving” section.)

If the light comes on while the engine is running,

you can drive the vehicle. However in these

cases, contact a NISSAN dealer for repair as

soon as possible.

The shift position indicator shows the vehicle

position when the power switch is in the ON or

READY to drive position. For more details, see

“Driving vehicle” in the “Starting and driving”

section of this manual.

2-26 Instruments and controls

When the power switch is pushed to the ON

position, modes of the trip computer can be

25. Parking brake release warning

This warning appears when the vehicle speed is

above 4 MPH (7km/h) and the parking brake is

applied.

A

selected by pushing the

Each time the switch

display will change as follows:

switch

.

᭺

A

is pushed, the

᭺

Charging time → Energy economy → State of

charge → Average speed → Driving distance and

elapsed time→ Setting → Warning check

TRIP COMPUTER

Switches for the trip computer are located on the

left side of the combination meter panel. To op-

erate the trip computer, push the following

switches:

A

switch

᭺

B

switch

᭺

Instruments and controls 2-27

NOTE:

• Immediately after charging has finished,

the charge time will be displayed as “--:--”.

• The estimated charging time stops updat-

ing if the air conditioner is turned on while

the Li-ion battery is charging. The esti-

mated charging time updates approxi-

mately 15 minutes after the air condi-

tioner is turned off.

• The 6 kW and the 3 kW charging time

typically shows different times to reach a

full charge.

• However, the same charging time may be

shown for both the 6 kW and the 3 kW based

on the Li-ion battery state of charge and battery

temperature.

Charging time

Displays the estimated time to a full Li-ion charge

based on the Charging Mode selected.

Energy economy

Average energy economy:

The average energy economy mode shows the

average energy economy since the last reset.

Resetting the average energy economy is done

B

• The system may automatically slow the battery

charge to prevent the battery from becoming

overcharged.

The time needed to charge the Li-ion battery

charges based on:

by pushing and holding the

switch

for

᭺

• Outside temperature

longer than 1 second. (The average speed is also

reset at the same time.)

• Li-ion battery temperature

• Available electrical power supplied to the

charger

The display is updated every 30 seconds. At

about the first 0.3 mile (500 m) after a reset, the

display shows “----”.

2-28 Instruments and controls

Instant energy economy:

The instant energy economy mode shows the

instant energy economy via a moving bar graph.

When regenerated energy is being stored in the

Li-ion battery while driving, the instant energy

economy display will show the maximum value.

State of charge (%)

Average speed

Displays the vehicles current state of charge.

The average speed mode shows the average

vehicle speed (MPH or km/h) since the last reset.

The average speed (MPH or km/h) can be reset

B

by pushing the

second.

switch

for longer than 1

᭺

The display is updated every 30 seconds. For the

first 30 seconds after a reset, the display shows

“----”.

Instruments and controls 2-29

A

B

The

switch

and

switch

are

᭺

used in the settings mode.

B

Push the

menus.

switch

to scroll through the

to select a menu.

᭺

A

Push the

᭺

Skip:

A

Push the

check mode.

switch

to move to the warning

to select other menus.

᭺

B

Push the

switch

᭺

Clock:

The clock can be adjusted in this menu.

• Back

Driving distance and elapsed time

Select this submenu to return to the top page

of the settings mode.

Driving distance:

The driving distance mode shows the total distance

(miles or km) the vehicle has been driven since the

last reset. The distance can be reset by pushing the

B

• Set Clock

Adjust the time (hour and minute) of the clock.

switch

for longer than 1 second. (The

᭺

For models without navigation system, the day of

the week can also be set to use it for the climate

control timer setting. (See “Climate Ctrl. timer” in

the “Display screen, heater, air conditioner, audio

and phone systems” section.)

elapsed time is also reset at the same time.)

Elapsed time:

Settings

The elapsed time mode shows the time since the

last reset. The displayed time can be reset by push-

Settings cannot be accessed while driving.

The message, “settings can only be ac-

cessed when stationary” is also displayed

on the vehicle information display.

• 24/12Hr (24 hours or 12 hours)

B

ing the

switch

for longer than 1 second.

᭺

Select either the 24-hour clock display or the

12-hour display.

(The driving distance is also reset at the same

time.)

2-30 Instruments and controls

Maintenance:

• Outside temp

• Back

Select this submenu to return to the top page

of the settings mode.

• Sound 1

Select this submenu to display the low outside

temperature (On or Off).

There are 5 submenus under the maintenance

menu.

• Back

Units:

• Sound 2

• Sound 3

• Off

Select this submenu to return to the top page

of the settings mode.

Units displayed can be set for the following items

on this menu.

• Tire

• Back

Select this submenu to set or reset the dis-

tance for replacement of the tires.

Select this submenu to return to the top page

of the settings mode.

Factory settings:

Select this menu to reset all values to the factory

default settings except for the odometer settings.

• Other -1, -2 and -3

• Temperature

• Speed

Select this submenu to set or reset the dis-

tance for replaceable/maintenance items. Up

to three other items can be monitored. Set

other items if required.

NOTE:

Language:

When resetting to the factory settings, all

previous settings made are restored to the

default settings.

Select this submenu to choose the language

displayed.

Alarms:

To return to the top page of the settings mode,

select “BACK”.

To return to the top page of the settings mode,

select “BACK”.

The alarms menu can be set to notify the follow-

ing items. There are 3 submenus under the

alarms menu.

Effects:

• Back

The start up sound can be selected or turned off

from this menu.

Select this submenu to return to the top page

of the settings mode.

5 submenus under the effects menu.

• Driver Alert

When a menu item is selected, the selected

sound plays.

Select this submenu to set the driver alert

period.

Instruments and controls 2-31

WARNING INFORMATION DISPLAYS

Low battery warning

When the low battery charge warning light

and the master warning light (yellow)

illu-

minate, the system displays a message on the

navigation screen that warns the driver that the

Li-ion battery power level is low.

1. The notification is displayed on the upper left

side of the screen. Touch [Show] to display

the screen showing detailed information.

Warning check

Skip:

A

Push the

switch

to move to the Esti-

᭺

mated charge time display.

B

Push the

menu.

switch

to select another

᭺

Detail:

This item is available only when a warning is

displayed.

Select this menu to see details of warnings.

2-32 Instruments and controls

NOTE:

• The low battery warning can be set to off.

See LEAF Navigation System Owner’s

Manual.

• When the battery power level is low, the

system automatically obtains charging

station information.

Limited power warning

When the Li-ion battery power level is extremely

low or the Li-ion battery malfunctions, the power

limitation indicator

light (yellow)

and the master warning

illuminate in the meter and the

2. The system displays a message screen and

announces the contents of the message to

warn that the Li-ion battery power level is low.

Check the message displayed on the screen.

Touch [Nearby Charging Station] to search all

charging stations that are located around the

current vehicle position.

system displays a message on the navigation

screen in order to inform the driver that power

output is restricted.

1. The notification is displayed on the upper left

side of the screen. Touch [Show] to display

the screen showing detailed information.

3. Touch [BACK] or push the MAP button to

return to the vehicle location screen.

Instruments and controls 2-33

wheels and tires” in the “Maintenance

and do-it-yourself” section. Many factors

including tire inflation, alignment, driving

habits and road conditions affect tire

wear and when tires should be replaced.

Setting the tire replacement indicator for

a certain driving distance does not mean

your tires will last that long. Use the tire

replacement indicator as a guide only

and always perform regular tire checks.

Failure to perform regular tire checks,

including tire pressure checks could re-

sult in tire failure. Serious vehicle dam-

age could occur and may lead to a colli-

sion, which could result in serious

personal injury or death.

2. The system displays a message screen and

announces the contents of the message to

warn that power output is restricted and in-

form the driver of the reason for this occur-

rence and what action is to be taken.

2. 3. 4. “Other” indicator

These indicators appears when the customer set

distance comes for checking or replacing main-

tenance items other than the tires. Other mainte-

nance items can include such things as the tire

rotation. You can set or reset the distance for

checking or replacing the items. (See “Trip com-

puter” in this section.) For scheduled mainte-

nance items and intervals, see your NISSAN Ser-

vice and Maintenance Guide.

INDICATORS FOR MAINTENANCE

1. Tire replacement indicator

This indicator appears when the customer set

distance comes for replacing tires. You can set or

reset the distance for replacing tires. (See “Trip

computer” in this section.)

WARNING

The tire replacement indicator is not a

substitute for regular tire checks, includ-

ing tire pressure checks. See “Changing

2-34 Instruments and controls

SECURITY SYSTEMS

selected and each setting information display

can be confirmed.

1. Timer setting status (charging and

Climate Ctrl.)

The timer setting status (ON or OFF) of the

charge and the climate control can be checked.

2. Charging timer setting confirmation

The charging timer starting hours, minutes and

days for the next charge time that has been set

can be checked.

3. Charging time

Displays the estimated time to charge the Li-ion

battery to a full charge. When fully charged, the

remaining charging time is displayed as “--:--”.

Your vehicle has two types of security systems,

as follows:

• Vehicle security system

4. Climate Ctrl. Timer setting

confirmation

The set time for ending hours and days of the

Climate Ctrl. Timer is displayed.

• NISSAN Vehicle Immobilizer System

The security status is shown by the security indi-

cator light.

VEHICLE SECURITY SYSTEM

INDICATOR FOR TIMER

When the power switch is turned off, this display

appears for 10 seconds. If the

pushed within 10 seconds, the display can be

The vehicle security system provides visual and

audio alarm signals if someone opens the doors,

or rear hatch when the system is armed. It is not,

however, a motion detection type system that

A

switch

is

᭺

Instruments and controls 2-35

activates when a vehicle is moved or when a

vibration occurs.

• the power door lock switch

• the mechanical key

The system helps deter vehicle theft but cannot

prevent it, nor can it prevent the theft of interior or

exterior vehicle components in all situations. Al-

ways secure your vehicle even if parking for a

brief period. Never leave your keys in the vehicle,

and always lock it when it is left unattended. Be

aware of your surroundings, and park in secure,

well-lit areas whenever possible.

4. Confirm that the security indicator light illumi-

nates. The security indicator light stays on for

about 30 seconds. The vehicle security sys-

tem is now pre-armed. After about 30 sec-

onds the vehicle security system automati-

cally shifts into the armed phase. The security

light begins to flash once every approximately

3 seconds. If, during this 30-second pre-arm

time period, the door is unlocked, or the

power switch is placed in the ACC or ON

position, the system will not arm.

Many devices offering additional protection, such

as component locks, identification markers, and

tracking systems, are available at auto supply

stores and specialty shops. Your NISSAN certi-

fied LEAF dealer may also offer such equipment.

Check with your insurance company to see if you

may be eligible for discounts for various theft

protection features.

Even when the driver and/or passengers

are in the vehicle, the system will activate

with all doors locked and the power switch

in the OFF position. When placing the

power switch to the ACC or ON position,

the system will be released.

How to arm the vehicle security

system

1. Close all windows.

The system can be armed even if the

windows are open.

2. Place the power switch in the LOCK or OFF

position and remove the Intelligent Key from

the vehicle.

Vehicle security system activation

The vehicle security system will give the following

alarm:

3. Close all doors. Lock all doors. The doors can

be locked with:

• The headlights blink and the horn sounds

intermittently.

• the LOCK

button on the Intelligent Key

• any request switch

2-36 Instruments and controls

• The alarm automatically turns off after approxi-

mately 50 seconds. However, the alarm reacti-

vates if the vehicle is tampered with again.

FCC Notice:

For USA:

NISSAN VEHICLE IMMOBILIZER

SYSTEM

The NISSAN Vehicle Immobilizer System will not

allow the power switch to be placed in the

READY to drive position without the use of the

registered key.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device may

not cause harmful interference, and (2) this

device must accept any interference re-

ceived, including interference that may

cause undesired operation.

The alarm is activated by:

• Unlocking the door without using the Intelligent

Key, the request switch or the key. (Even if the

door is opened by releasing the door inside lock

knob, the alarm will activate.)

If the power switch fails to place the vehicle into

the READY to drive position using the registered

key, it may be due to interference caused by

another registered key, an automated toll road

device or automated payment device on the key

ring. Restart the EV system using the following

procedure:

• Opening the hood.

How to stop an activated alarm

The alarm will stop when a door is unlocked by

NOTE:

Changes or modifications not expressly ap-

proved by the party responsible for compli-

ance could void the user’s authority to op-

erate the equipment.

pushing the UNLOCK

button on the Intel-

ligent Key, door handle request switch or using

the mechanical key, or when the power switch is

pushed in the ACC or ON position.

1. Leave the power switch in the ON position for

approximately 5 seconds.

For Canada:

2. Place the power switch in the OFF position

and wait approximately 10 seconds.

If the system does not operate as described

above, have it checked by a NISSAN certi-

fied LEAF dealer.

This device complies with Industry Canada

licence-exempt RSS standard(s). Opera-

tion is subject to the following two condi-

tions: (1) this device may not cause inter-

ference, and (2) this device must accept any

interference, including interference that

may cause undesired operation of the

device.

3. Repeat step 1 and 2 again.

4. Place the power switch in the READY to drive

position while holding the device (which may

have caused the interference) separate from

the registered key.

If this procedure allows power switch in the

READY to drive mode, NISSAN recommends

placing the registered key on a separate key

ring to avoid interference from other devices.

Instruments and controls 2-37

WINDSHIELD WIPER AND WASHER

SWITCH

If the light still remains on and/or the

power switch cannot be placed in the

READY to drive position, see a NISSAN

certified LEAF dealer for a NISSAN Vehicle

Immobilizer System service as soon as

possible. Please bring all registered keys

that you have when visiting a NISSAN cer-

tified LEAF dealer for service.

WARNING

In freezing temperatures the washer so-

lution may freeze on the windshield and

obscure your vision which may lead to an

accident. Warm the windshield with the

defroster before you wash the wind-

shield.

CAUTION

•

Do not operate the washer continu-

ously for more than 30 seconds.

Do not operate the washer if the reser-

voir tank is empty.

Do not fill the window washer reservoir

tank with washer fluid concentrates at

full strength. Some methyl alcohol

based washer fluid concentrates may

permanently stain the grille if spilled

while filling the window washer reser-

voir tank.

Pre-mix washer fluid concentrates

with water to the manufacturer’s rec-

ommended levels before pouring the

fluid into the window washer reservoir

tank. Do not use the window washer

reservoir tank to mix the washer fluid

concentrate and water.

Security indicator light

The security indicator light is located on the me-

ter panel. It indicates the status of the NISSAN

Vehicle Immobilizer System.

The light blinks after the power switch was in the

ACC or OFF position. This function indicates the

security systems equipped on the vehicle are

operational.

•

If the NISSAN Vehicle Immobilizer System is mal-

functioning, this light will remain on while the

power switch is in the ON position.

2-38 Instruments and controls

If the windshield wiper operation is inter-

rupted by snow or ice, the wiper may stop

moving to protect its motor. If this occurs,

turn the wiper switch to the OFF position

and remove the snow or ice that is on and

around the wiper arms. In approximately 1

minute, turn the switch on again to operate

the wiper.

WASHER OPERATION

To operate the washer, pull the lever toward the

5

back of the vehicle

until the desired amount of

᭺

washer fluid is spread on the windshield. The

wiper will automatically operate several times.

The windshield wiper and washer operates when

the power switch is in the ON position.

Push the lever down to operate the wiper at the

following speed:

1

Intermittent — intermittent operation can be

᭺

A

adjusted by turning the knob toward

᭺

B

(Slower) or

(Faster).

᭺

2

Low — continuous low speed operation

High — continuous high speed operation

MIST — one sweep operation of the wiper

᭺

3

᭺

4

᭺

Instruments and controls 2-39

REAR WINDOW WIPER AND

WASHER SWITCH

If the rear window wiper operation is inter-

rupted by snow etc., the wiper may stop

moving to protect its motor. If this occurs,

turn the wiper switch to the OFF position

and remove the snow etc. on and around

the wiper arms. After about 1 minute, turn

the switch ON again to operate the wiper.

WARNING

In freezing temperatures the washer so-

lution may freeze on the rear window

glass and obscure your vision. Warm the

rear window with the defroster before

you wash the rear window.

CAUTION

•

Do not operate the washer continu-

ously for more than 30 seconds.

Do not operate the washer if the reser-

voir tank is empty.

Do not fill the window washer reservoir

tank with washer fluid concentrates at

full strength. Some methyl alcohol

based washer fluid concentrates may

permanently stain the grille if spilled

while filling the window washer reser-

voir tank.

The rear window wiper and washer operate when

the power switch is in the ON position.

Turn the switch clockwise from the OFF position

to operate the wiper.

1

Intermittent (INT) — intermittent operation

᭺

(not adjustable)

•

Pre-mix washer fluid concentrates

with water to the manufacturer’s rec-

ommended levels before pouring the

fluid into the window washer reservoir

tank. Do not use the window washer

reservoir tank to mix the washer fluid

concentrate and water.

2

Low (ON) — continuous low speed operation

᭺

3

Push the switch forward

washer. Then the wiper will also operate several

times.

to operate the

᭺

2-40 Instruments and controls

REAR WINDOW AND OUTSIDE

MIRROR DEFROSTER SWITCH

INSTRUMENT BRIGHTNESS

CONTROL

Type A

Type B

1

If the button

is pushed again, the instrument

To defog/defrost the rear window glass and out-

side mirrors, place the power switch in the ON

position and push the switch

light will illuminate. Push the switch again to turn

the defroster off.

᭺

The instrument brightness control switch can be

operated when the power switch is in the ON

position. When the switch is operated, the ve-

hicle information display switches to the bright-

ness adjustment mode.

lights are turned on to the lowest brightness

setting.

1

on. The indicator

᭺

It will automatically turn off in approximately 15

minutes.

1

Push the switch

to display the setting menu of

᭺

the brightness control on the vehicle information

display.

CAUTION

1

Push the

button to move the bar to the + side.

᭺

When cleaning the inner side of the rear

window, be careful not to scratch or dam-

age the rear window defroster.

If the bar reaches the maximum brightness, a

chime will sound. If the button

when the brightness is at the maximum setting,

the instrument lights turn off.

1

is pushed again

᭺

Instruments and controls 2-41

HEADLIGHT AND TURN SIGNAL

SWITCH

The autolight system can turn on the headlights

automatically when it is dark and turn off the

headlights when it is light.

For US models: The headlights will also be turned

on automatically at twilight or in rainy weather

(when the windshield wiper is operated continu-

ously).

If the power switch is placed in the OFF position

and one of the doors is opened and this condition

continues, the headlights remain on for 45 sec-

onds.

Automatic headlights off delay:

You can keep the headlights on for up to 180

seconds after you push the power switch to OFF

and open any door then close all the doors.

HEADLIGHT SWITCH

Autolight system (if so equipped)

The autolight system allows the headlights to be

set so they turn on and off automatically.

Lighting

You can adjust the period of the automatic head-

lights off delay from 0 seconds (OFF) to 180

seconds. The factory default setting is 45 sec-

onds.

1

Turn the switch to the

position:

᭺

To set the autolight system:

The front park, side marker, tail, license plate

and the instrument light will come on.

1. Make sure the headlight switch is in the AUTO

2

Turn the switch to the

position:

1

position

.

᭺

The headlights will come on and all the other

lights will remain on.

For automatic headlights off delay setting, see

the LEAF Navigation System Owner’s Manual.

2. Place the power switch in the ON position.

3. The autolight system automatically turns the

headlights on and off.

To turn the autolight system off, turn the switch to

the OFF,

or

position.

2-42 Instruments and controls

Battery saver system

• When the headlight switch is in the

or

position while the power switch is in the

ON position, the lights will automatically turn off

45 seconds after the power switch has been

placed in the OFF position.

• When the headlight switch remains in the

or

position after the lights automatically

turn off, the lights will turn on when the power

switch is placed in the ON position.

CAUTION

•

When you turn on the headlight switch

again after the lights automatically

turn off, the lights will not turn off

automatically. Be sure to turn the light

switch to the OFF position when you

leave the vehicle for extended periods

of time, otherwise the battery will be

discharged.

Be sure not to put anything on top of the

1

Headlight beam select

photo sensor

located on the top of the

᭺

1

To select the low beam, put the lever in the

neutral position as shown.

To select the high beam, push the lever

forward while the switch is in the

position. Pull it back to select the low

beam.

᭺

instrument panel. The photo sensor con-

trols the autolight; if it is covered, the photo

sensor reacts as if it is dark and the head-

lights will illuminate.

2

᭺

•

Never leave the light switch on when

the power switch is in the OFF, ACC or

ON position for extended periods of

time even if the headlights turn off

automatically.

3

Pulling the lever toward you will flash the

᭺

headlight high beam even when the head-

light switch is in the OFF position.

Instruments and controls 2-43

FOG LIGHT SWITCH (IF SO

EQUIPPED)

Daytime running light system (for

Canada)

The daytime running lights automatically illumi-

nate when the power switch is in the READY to

drive position with the parking brake released.

The daytime running lights operate with the head-

light switch in the OFF position. Turn headlight

switch to the

position for full illumination

when driving at night.

If the parking brake is applied before the power

switch is in the READY to drive position, daytime

running lights do not operate. The daytime run-

ning lights illuminate once the parking brake is

released. The daytime running lights will remain

on until the power switch is pushed to the OFF

position.

To turn the fog lights on, turn the headlight switch

TURN SIGNAL SWITCH

to the

position, then turn the switch to the

1

Turn signal

᭺

position. To turn them off, turn the switch to

Move the lever up or down to signal the turning

direction. When the turn is completed, the turn

signals cancel automatically.

the OFF position.

The headlights must be on for the fog lights to

operate.

2

᭺

Lane change signal

To indicate a lane change, move the lever up or

down to the point where lights begin flashing.

The turn signal will flash three times automati-

cally.

2-44 Instruments and controls

HEATED STEERING WHEEL SWITCH

indicator light will remain on as long as the sys-

tem is on.

• The heated steering wheel consumes less

power than the heater and can be used to

either help extend vehicle range by reduc-

ing heater use or to maximize comfort by

supplementing the heater.

Push the switch again to turn the heated steering

wheel system off manually. The indicator light turn

off.

NOTE:

• If the surface temperature of the steering

wheel is above 68°F (20°C) when the

switch is turned on, the system will not

heat the steering wheel. This is not a

malfunction.

• If the outside temperature is low (approxi-

mately 50°F (10°C) or less) and the Climate

Ctrl. Timer or Remote Climate Control are

used, the steering wheel heater will auto-

matically operate in the following

conditions.

The heated steering wheel system is designed to

operate only when the surface temperature of the

steering wheel is below approximately 68°F

(20°C).

– When using the Climate Ctrl. Timer:

Operates from approximately 15 min-

utes before the set departure time until

the set departure time.

Push the heated steering wheel switch to warm

the steering wheel when the power switch is in

1

the ON position. The indicator light

switch will illuminate.

on the

᭺

– When using Remote Climate Control:

Operates 15 minutes after Remote Cli-

mate Control starts.

If the surface temperature of the steering wheel is

below approximately 68°F (20°C), the system will

heat the steering wheel and cycle off and on to

maintain a temperature above 68°F (20°C). The

Instruments and controls 2-45

HORN

ECO SWITCH

HEATED SEAT SWITCH

To activate the ECO mode, press the ECO

To sound the horn, push the center pad area of

the steering wheel.

1

switch

on the right side of the steering wheel.

᭺

The “ECO indicator light” on the instrument clus-

ter will illuminate.

WARNING

To deactivate the ECO mode, press the ECO

Do not disassemble the horn. Doing so

could affect proper operation of the

supplemental front air bag system. Tam-

pering with the supplemental front air

bag system may result in serious per-

sonal injury.

1

switch

again. The “ECO indicator light”on the

᭺

instrument cluster will go out.

See “Electronic Shift Control System” in the

“Starting and Driving” section.

2-46 Instruments and controls

The heater is controlled by a thermostat, auto-

matically turning the heater on and off. The indi-

cator light will remain on as long as the switch is

on.

CAUTION

•

Do not use the seat heater for ex-

tended periods or when no one is us-

ing the seat.

Do not put anything on the seat which

insulates heat, such as

When the vehicle’s interior is warmed, or before

you leave the vehicle, be sure to turn the switch

off.

a

blanket,

cushion, seat cover, etc. Otherwise, the

seat may become overheated.

Do not place anything hard or heavy on

the seat or pierce it with a pin or similar

object. This may result in damage to

the heater.

Any liquid spilled on the heated seat

should be removed immediately with a

dry cloth.

When cleaning the seat, never use

gasoline, thinner, or any similar mate-

rials.

If any abnormalities are found or the

heated seat does not operate, turn the

switch off and have the system

checked by a NISSAN certified LEAF

dealer.

NOTE:

•

The heated seats consumes less power

than the heater and can be used to either

help extend vehicle range by reducing

heater use or to maximize comfort by

supplementing the heater.

•

Rear

The front seats and the rear outboard seats can

be warmed by built-in heaters. The switches lo-

cated on the center console and at the side of the

front passenger seatback can be operated inde-

pendently of each other.

WARNING

Do not use or allow occupants to use the

seat heater if you or the occupants can-

not monitor elevated seat temperatures

or have an inability to feel pain in those

body parts in contact with the seat. Use of

the seat heater by such people could re-

sult in serious injury.

1. Place the power switch in the ON position.

2. Push the LO or HI position of the switch, as

desired, depending on the temperature. The

indicator light in the switch will illuminate.

3. To turn off the heater, return the switch to the

level position. Make sure the indicator light

goes off.

Instruments and controls 2-47

VEHICLE DYNAMIC CONTROL (VDC)

OFF SWITCH

CHARGE PORT LID SWITCH

Push the VDC OFF switch again to turn on the

VDC system, or the VDC is automatically turned

back on when the power switch is placed in the

off position and then placed back in the READY

to drive position. See “Vehicle Dynamic Control

(VDC) system” in the “Starting and driving” sec-

tion.

To open the charge port lid, push the charge port

lid switch. See “Charge Port Lid” in the “Pre-

Driving Checks and Adjustments” section.

The vehicle should be driven with the Vehicle

Dynamic Control (VDC) system on for most driv-

ing conditions.

If the vehicle is stuck in mud or snow, the VDC

system reduces the traction motor output to re-

duce wheel spin. The traction motor speed will be

reduced even if the accelerator is depressed to

the floor. If maximum traction motor power is

needed to free a stuck vehicle, turn the VDC

system off.

To turn off the VDC system, push the VDC OFF

switch. The

indicator will illuminate.

2-48 Instruments and controls

CHARGE CONNECTOR LOCK SWITCH

CHARGE TIMER OFF SWITCH

POWER OUTLET

To lock or unlock the charge connector, push the

charge connector lock switch. See “Charge

Connector Lock Switch” in the “Charging” sec-

tion.

To turn off the charge timer, push the charge

timer OFF switch. See “Charging Timer” in the

“Charging” section.

The power outlet is located in the instrument

panel.

CAUTION

•

The outlet and plug may be hot during

or immediately after use.

Do not use with accessories that ex-

ceed

a

12-volt, 120W (10A) power

draw. Do not use double adapters or

more than one electrical accessory.

Instruments and controls 2-49

STORAGE

CUP HOLDERS

•

Use the power outlet with the power

switch is in the ON or READY to drive

position to avoid discharging the 12-

volt battery.

Avoid using the power outlet when the

air conditioner, headlights or rear win-

dow defroster are on.

This power outlet is not designed for

use with a cigarette lighter unit.

Push the plug in as far as it will go. If

good contact is not made, the plug may

overheat or the internal temperature

fuse may open.

CAUTION

Avoid abrupt starting and braking

•

when the cup holder is being used to

prevent spilling the drink. If the liquid

is hot, it can scald you or your passen-

ger.

•

Use only soft cups in the cup holder.

Hard objects can injure you in an acci-

dent.

•

Before inserting or disconnecting a

plug, make sure that the electrical ac-

cessory being used is turned OFF.

When not in use, be sure to close the

cap. Do not allow water to contact the

outlet.

Front

2-50 Instruments and controls

SEATBACK POCKET

SUNGLASSES HOLDER

To open the sunglasses holder, push and release.

Only store one pair of sunglasses in the holder.

Soft bottle holders

The seatback pocket is located on the back of the

passenger’s seat. The pocket can be used to

store maps.

CAUTION

Do not use the bottle holder for any

WARNING

•

Keep the sunglasses holder closed while

driving to prevent an accident.

other objects that could be thrown

about in the vehicle and possibly injure

people during sudden braking or an

accident.

Do not use the bottle holder for open

liquid containers.

Instruments and controls 2-51

CAUTION

•

Do not use for anything other than

sunglasses.

Do not leave sunglasses in the sun-

glasses holder while parking in direct

sunlight. The heat may damage the

sunglasses.

GLOVE BOX

CONSOLE BOX

A

To open the glove box, pull the handle.

To open the console box, push up the knob

᭺

and pull up the lid. To close, push the lid down

until it is latched.

To close, push the lid in until the lock latches.

WARNING

Keep the glove box lid closed while driv-

ing to prevent injury in case of an acci-

dent or a sudden stop.

2-52 Instruments and controls

TONNEAU COVER (IF SO

EQUIPPED)

– If the tonneau cover contacts the top

tether strap when it is attached to

the top tether anchor, remove the

tonneau cover from the vehicle or

secure it on the cargo floor below its

attachment location. If the tonneau

cover is not removed, it may damage

the top tether strap during a colli-

sion.

WARNING

•

Never put anything on the tonneau

cover, no matter how small. Any object

on it could cause an injury in an acci-

dent or sudden stop.

– Do not allow cargo to contact the

top tether strap when it is attached

to the top tether anchor. Properly

secure the cargo so it does not con-

tact the top tether strap. Cargo that

is not properly secured or that con-

tacts the top tether strap may dam-

age the top tether strap during a

collision.

•

Do not leave the tonneau cover in the

vehicle with it disengaged from the

holder.

Properly secure all cargo with ropes or

straps to help prevent it from sliding or

shifting. Do not place cargo higher

than the seatbacks. In a sudden stop or

collision, unsecured cargo could cause

personal injury.

•

Your child could be seriously injured or

killed in a collision if the child restraint

top tether strap is damaged.

The tonneau cover keeps the luggage compart-

ment contents hidden from the outside.

To remove the tonneau cover:

1. Remove the straps from the rear hatch.

2. Pull up the tonneau cover.

3. Remove the tonneau cover holders from the

rear pillar.

Instruments and controls 2-53

STOWING GOLF BAGS

LUGGAGE SIDE HOOK

Normally, two standard golf bags can be stowed

in the cargo area. Insert the top of the golf bag

CAUTION

1

into right side of the cargo area

then rotate the

᭺

Do not apply a total load of more than 4 lb

(2 kg) to the hook. Doing so may cause

the hook to break.

2

bag backward

bag into right side of the cargo area

. Insert the top of the 2nd golf

᭺

3

and stow

᭺

4

the bottom of golf bag forward all the way

.

᭺

The hook is located at the side of the luggage

room. Use the hook to secure the Electric Vehicle

Supply Equipment (EVSE).

In some cases, you may not be able to stow two

golf bags in your vehicle, depending on their sizes

or types.

4. Slide down the tonneau cover along the rear

seat back.

5. Remove the tonneau cover by pulling either

the left or right side backward away from the

pillar.

2-54 Instruments and controls

WINDOWS

POWER WINDOWS

Locking passengers’ windows

C

When the lock button

is pushed in, only the

᭺

driver side window can be opened or closed.

Push it in again to cancel.

WARNING

Make sure that all passengers have

their hands, etc. inside the vehicle

while it is in motion and before closing

the windows. Use the window lock

switch to prevent unexpected use of

the power windows.

Do not leave children unattended in-

side the vehicle. They could unknow-

ingly activate switches or controls and

become trapped in the window. Unat-

tended children could become in-

volved in serious accidents.

•

Main power window switch (driver’s

side)

The power windows operate when the power

switch is in the ON position, or for about 45

seconds after the power switch is placed in the

OFF position. If the driver’s or front passenger’s

door is opened during this period of about 45

seconds, power to the windows is canceled.

1. Driver side window

2. Front passenger side window

3. Rear left passenger side window

4. Rear right passenger side window

5. Window lock button

A

To open or close the window, push down

or

᭺

B

pull up

the switch and hold it. The main switch

(driver’s side switches) will open or close all the

windows.

᭺

Instruments and controls 2-55

Auto-reverse function

WARNING

There are some small distances immedi-

ately before the closed position which

cannot be detected. Make sure that all

passengers have their hands, etc., inside

the vehicle before closing the window.

If the control unit detects something caught in the

window as it is closing, the window will be imme-

diately lowered.

The auto reverse function can be activated when

the window is closed by automatic operation

when the power switch is in the ON position or

for 45 seconds after the power switch is placed

in the OFF position.

Passenger side power window switch

Automatic operation

The automatic operation is available for the

switch that has an

The passenger’s side power window switch will

open or close only the corresponding window. To

open or close the window, push down or pull up

the switch and hold it.

mark on its surface.

To fully open or close the window, completely

push down or pull up the switch and release it;

the switch need not be held. The window will

automatically open or close all the way. To stop

the window, just push or lift the switch in the

opposite direction.

Depending on the environment or driving

conditions, the auto reverse function may

be activated if an impact or load similar to

something being caught in the window oc-

curs.

A light push or pull on the switch will cause the

window to open or close until the switch is re-

leased.

2-56 Instruments and controls

INTERIOR LIGHTS

If the windows do not close

automatically

If the power window automatic function (closing

only) does not operate properly, perform the fol-

lowing procedure to initialize the power window

system.

CAUTION

Do not use for extended periods of time

with the power switch in the OFF posi-

tion. This could result in a discharged

12-volt battery.

1. Place the power switch in the ON position.

2. Close the door.

3. Open the window completely by operating

the power window switch.

4. Pull the power window switch and hold it to

close the window, and then hold the switch

more than 3 seconds after the window is

closed completely.

MAP LIGHTS

Push the button to turn the map lights on. To turn

them off, press the button again.

5. Release the power window switch. Operate

the window by the automatic function to con-

firm the initialization is complete.

If the power window automatic function does not

operate properly after performing the procedure

above, have your vehicle checked by a NISSAN

certified LEAF dealer.

Instruments and controls 2-57

DOOR position

CARGO LIGHT

2

When the switch is in the DOOR position , the

The light illuminates when the trunk lid is opened.

When the trunk lid is closed, the light goes off.

For blub replacement procedures, refer to “Exte-

rior and interior lights” in the “Maintenance and

do-it-yourself” section of this manual.

᭺

ceiling light will illuminate under the following

conditions:

• the power switch is placed in the LOCK

position.

– remains on for about 15 seconds.

• doors are unlocked by pushing the UNLOCK

button or the request switch, with the

power switch in the LOCK position

– remains on for about 15 seconds.

• any door is opened and then closed with the

power switch in the LOCK position

– remains on for about 15 seconds.

CEILING LIGHT

The ceiling light switch has three positions: ON ,

DOOR and OFF.

• any door is opened with the power switch in the

ACC or ON position

– remains on while the door is opened. When

the door is closed, the light turns off.

ON position

1

When the switch is in the ON position

ceiling light will illuminate.

, the

᭺

The light will automatically turn off after 10

minutes when the light remains illuminated

to prevent the battery from becoming dis-

charged.

OFF position

3

When the switch is in the OFF position

, the

᭺

ceiling light will not illuminate, regardless of the

condition.

2-58 Instruments and controls

HOMELINK® UNIVERSAL

TRANSCEIVER (IF SO EQUIPPED)

The HomeLink® Universal Transceiver provides

a convenient way to consolidate the functions of

up to three individual hand-held transmitters into

one built-in device.

PROGRAMMING HOMELINK®

WARNING

If you have any questions or are having difficulty

programming your HomeLink® buttons, refer to

the HomeLink® web site at: www.homelink.com

or call 1-800-355-3515.

•

Do not use the HomeLink® Universal

Transceiver with any garage door

opener that lacks safety stop and re-

verse features as required by federal

safety standards. (These standards be-

came effective for opener models

manufactured after April 1, 1982.) A

garage door opener that cannot detect

an object in the path of a closing ga-

rage door and then automatically stop

and reverse, does not meet current

federal safety standards. Using a ga-

rage door opener without these fea-

tures increases the risk of serious in-

jury or death.

During the programming procedure,

your garage door or security gate will

open or close (if the transmitter is

within range). Make sure that people

or objects are clear of the garage door,

gate, etc. that you are programming.

Place the power switch in the ACC or

ON position while programming the

HomeLink® Universal Transceiver.

HomeLink® Universal Transceiver:

• Will operate most Radio Frequency (RF) de-

vices such as garage doors, gates, home and

office lighting, entry door locks and security

systems.

NOTE:

Place the ignition switch in the ACC posi-

tion when programming HomeLink®. It is

also recommended that a new battery be

placed in the hand-held transmitter of the

device being programmed to HomeLink®

for quicker programming and accurate

transmission of the radio-frequency.

• Is powered by the vehicle’s 12-volt battery. No

separate batteries are required. If the vehicle’s

12-volt battery is discharged or is discon-

nected, HomeLink® will retain all programming.

Once the HomeLink® Universal Trans-

ceiver is programmed, retain the original

transmitter for future programming proce-

dures (for example, new vehicle pur-

chases). Upon sale of the vehicle, the pro-

1. Position the end of your hand-held transmitter

1–3 inches (2–8 cm) away from the

HomeLink® surface, keeping the HomeLink®

1

•

indicator light

in view.

᭺

grammed

HomeLink®

Universal

Transceiver buttons should be erased for

security purposes. For additional informa-

tion, see “Programming HomeLink®” in

this section.

Instruments and controls 2-59

4. At the receiver located on the garage door

opener motor in the garage, locate the “learn”

or “smart” button (the name and color of the

button may vary by manufacturer but it is

usually located near where the hanging an-

tenna wire is attached to the unit). If there is

difficulty locating the button, reference the

garage door opener’s manual.

5. Press and release the “learn” or “smart”

button.

6. Return to the vehicle and firmly press and hold

the trained HomeLink® button for two sec-

onds and release. Repeat the “press/hold/

release” sequence up to 3 times to complete

the training process. HomeLink® should now

activate your rolling code equipped device.

2. Using both hands, simultaneously press and

hold the desired HomeLink® button and

handheld transmitter button. DO NOT release

1

3. Press and hold the programmed HomeLink®

button and observe the indicator light.

1

• If the indicator light

is solid/

᭺

until the HomeLink® indicator light

flashes

᭺

continuous, programming is complete

and your device should activate when the

HomeLink® button is pressed and released.

7. If you have any questions or are having diffi-

culty programming your HomeLink® buttons,

refer to the HomeLink® web site at:

www.homelink.com or call 1-800-355-3515.

slowly and then rapidly. When the indicator

light flashes rapidly, both buttons may be re-

leased. (The rapid flashing indicates success-

ful programming.)

1

• If the indicator light

blinks rapidly for

᭺

two seconds and then turns to a solid/

continuous light, continue with Steps

4-6 for a rolling code device. A second per-

son may make the following steps easier.

Please use a ladder or other device. Do not

stand on your vehicle to perform the next

steps.

NOTE:

Some devices may require you to re-

place Step 2 with the cycling procedure

noted in the “Programing HomeLink®

for Canadian customers and gate open-

ers” section.

2-60 Instruments and controls

stop transmitting. Continue to press and hold

the desired HomeLink® button while you

press and re-press (“cycle”) your hand-held

transmitter every two seconds until the fre-

quency signal has been learned. The

HomeLink® indicator light will flash slowly

and then rapidly after several seconds upon

successful training. DO NOT release until the

HomeLink® indicator light flashes slowly and

then rapidly. When the indicator light flashes

rapidly, both buttons may be released. The

rapid flashing indicates successful training.

For convenience, the hand-held transmitter of the

device may also be used at any time.

PROGRAMMING HOMELINK® FOR

CANADIAN CUSTOMERS AND

GATE OPENERS

Canadian radio-frequency laws require transmit-

ter signals to “time-out” (or quit) after several

seconds of transmission – which may not be long

enough for HomeLink® to pick up the signal

during training. Similar to this Canadian law,

some U.S. gate operators are designed to “tim-

eout” in the same manner.

PROGRAMMING TROUBLE-

DIAGNOSIS

If HomeLink® does not quickly learn the hand-

held transmitter information, perform the follow-

ing steps.

• Replace the hand-held transmitter batteries

with new batteries.

• Position the hand-held transmitter with its bat-

tery area facing away from the HomeLink®

surface.

If you live in Canada or you are having difficulties

training a gate operator or garage door opener

by using the “Training” procedures, replace “Pro-

gramming HomeLink®” Step 2 with the follow-

ing:

Proceed with “Programming HomeLink®” step 3

to complete.

• Push and hold both the HomeLink® and hand-

held transmitter buttons without interruption.

If the device was unplugged during the program-

ming procedure, remember to plug it back in

when programming is completed.

• Position the hand-held transmitter 1 to 3 inches

(2 to 8 cm) away from the HomeLink® surface.

Hold the transmitter in that position for up to 15

seconds. If HomeLink® is not programmed

within that time, try holding the transmitter in

another position while keeping the indicator

light in view at all times.

NOTE:

When programming a garage door opener,

etc., unplug the device during the “cycling”

process to prevent possible damage to the

garage door opener components.

OPERATING THE HOMELINK®

UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after it is

programmed, can be used to activate the pro-

grammed device. To operate, simply press and

1. See “Programing HomeLink®” step 1 in this

section.

If you continue to have programming difficulties,

please contact the NISSAN Consumer Affairs

Department. The phone numbers are located in

the Foreword of this Owner’s Manual.

release

the

appropriate

programmed

2. Using both hands, simultaneously press and

hold the desired HomeLink® button and the

hand-held transmitter button. During training,

your hand-held transmitter may automatically

HomeLink® Universal Transceiver button. The

amber indicator light will illuminate while the sig-

nal is being transmitted.

Instruments and controls 2-61

2. The indicator light will begin to flash after 20

seconds. Without releasing the HomeLink®

FCC notice:

For USA:

CLEARING THE PROGRAMMED

INFORMATION

The following procedure clears the programmed

information from both buttons. Individual buttons

cannot be cleared. However, individual buttons

can be reprogrammed, see “Reprogramming a

single HomeLink® button” in this section.

button,

proceed

with

“Programming

This device complies with Part 15 of the

FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device may

not cause harmful interference, and (2) this

device must accept any interference re-

ceived, including interference that may

cause undesired operation.

HomeLink®” - Step 1.

For questions or comments, contact HomeLink®

at: www.homelink.com or 1–800–355–3515.

The HomeLink® Universal Transceiver button

has now been reprogrammed. The new device

can be activated by pushing the HomeLink®

button that was just programmed. This procedure

will not affect any other programmed HomeLink®

buttons.

To clear all programming:

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to flash

in approximately 10 seconds. Do not hold for

longer than 20 seconds.

NOTE:

Changes or modifications not expressly ap-

proved by the party responsible for compli-

ance could void the user’s authority to op-

erate the equipment.

IF YOUR VEHICLE IS STOLEN

2. Release both buttons.

If your vehicle is stolen, you should change the

codes of any non-rolling code device that has

been programmed into HomeLink®. Consult the

Owner’s Manual of each device or call the manu-

facturer or dealer of those devices for additional

information.

HomeLink® is now in the programming mode

and can be programmed at any time beginning

with “Programming HomeLink®” - Step 1.

For Canada:

This device complies with Industry Canada

licence-exempt RSS standard(s). Opera-

tion is subject to the following two condi-

tions: (1) this device may not cause inter-

ference, and (2) this device must accept any

interference, including interference that

may cause undesired operation of the

device.

REPROGRAMMING A SINGLE

HOMELINK® BUTTON

To reprogram a HomeLink® Universal Trans-

ceiver button, complete the following:

When your vehicle is recovered, you will

need to reprogram the HomeLink® Univer-

sal Transceiver with your new transmitter

information.

1. Press and hold the desired HomeLink® but-

ton. DO NOT release the button.

2-62 Instruments and controls

Instruments and controls for Your Nissan Leaf 4 Door First Generation (2010-2017)

Related Topics

Popular Owner Manuals

Latest Owner Manuals