Get Instruments and controls -> Programming HomeLink? Guide for Nissan Leaf 4 Door First Generation (2010-2017)

HOMELINK® UNIVERSAL

TRANSCEIVER (IF SO EQUIPPED)

The HomeLink® Universal Transceiver provides

a convenient way to consolidate the functions of

up to three individual hand-held transmitters into

one built-in device.

PROGRAMMING HOMELINK®

WARNING

If you have any questions or are having difficulty

programming your HomeLink® buttons, refer to

the HomeLink® web site at: www.homelink.com

or call 1-800-355-3515.

•

Do not use the HomeLink® Universal

Transceiver with any garage door

opener that lacks safety stop and re-

verse features as required by federal

safety standards. (These standards be-

came effective for opener models

manufactured after April 1, 1982.) A

garage door opener that cannot detect

an object in the path of a closing ga-

rage door and then automatically stop

and reverse, does not meet current

federal safety standards. Using a ga-

rage door opener without these fea-

tures increases the risk of serious in-

jury or death.

During the programming procedure,

your garage door or security gate will

open or close (if the transmitter is

within range). Make sure that people

or objects are clear of the garage door,

gate, etc. that you are programming.

Place the power switch in the ACC or

ON position while programming the

HomeLink® Universal Transceiver.

HomeLink® Universal Transceiver:

• Will operate most Radio Frequency (RF) de-

vices such as garage doors, gates, home and

office lighting, entry door locks and security

systems.

NOTE:

Place the ignition switch in the ACC posi-

tion when programming HomeLink®. It is

also recommended that a new battery be

placed in the hand-held transmitter of the

device being programmed to HomeLink®

for quicker programming and accurate

transmission of the radio-frequency.

• Is powered by the vehicle’s 12-volt battery. No

separate batteries are required. If the vehicle’s

12-volt battery is discharged or is discon-

nected, HomeLink® will retain all programming.

Once the HomeLink® Universal Trans-

ceiver is programmed, retain the original

transmitter for future programming proce-

dures (for example, new vehicle pur-

chases). Upon sale of the vehicle, the pro-

1. Position the end of your hand-held transmitter

1–3 inches (2–8 cm) away from the

HomeLink® surface, keeping the HomeLink®

•

indicator light

in view.

᭺

grammed

HomeLink®

Universal

Transceiver buttons should be erased for

security purposes. For additional informa-

tion, see “Programming HomeLink®” in

this section.

Instruments and controls 2-59

4. At the receiver located on the garage door

opener motor in the garage, locate the “learn”

or “smart” button (the name and color of the

button may vary by manufacturer but it is

usually located near where the hanging an-

tenna wire is attached to the unit). If there is

difficulty locating the button, reference the

garage door opener’s manual.

5. Press and release the “learn” or “smart”

button.

6. Return to the vehicle and firmly press and hold

the trained HomeLink® button for two sec-

onds and release. Repeat the “press/hold/

release” sequence up to 3 times to complete

the training process. HomeLink® should now

activate your rolling code equipped device.

2. Using both hands, simultaneously press and

hold the desired HomeLink® button and

handheld transmitter button. DO NOT release

3. Press and hold the programmed HomeLink®

button and observe the indicator light.

• If the indicator light

is solid/

᭺

until the HomeLink® indicator light

flashes

᭺

continuous, programming is complete

and your device should activate when the

HomeLink® button is pressed and released.

7. If you have any questions or are having diffi-

culty programming your HomeLink® buttons,

refer to the HomeLink® web site at:

www.homelink.com or call 1-800-355-3515.

slowly and then rapidly. When the indicator

light flashes rapidly, both buttons may be re-

leased. (The rapid flashing indicates success-

ful programming.)

• If the indicator light

blinks rapidly for

᭺

two seconds and then turns to a solid/

continuous light, continue with Steps

4-6 for a rolling code device. A second per-

son may make the following steps easier.

Please use a ladder or other device. Do not

stand on your vehicle to perform the next

steps.

NOTE:

Some devices may require you to re-

place Step 2 with the cycling procedure

noted in the “Programing HomeLink®

for Canadian customers and gate open-

ers” section.

2-60 Instruments and controls

Instruments and controls -> Programming HomeLink? for Your Nissan Leaf 4 Door First Generation (2010-2017)

Related Topics

Popular Owner Manuals

Latest Owner Manuals