2022-2026 Nissan X Trail SUV Starting and driving -> Speed limiter (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting and driving -> Speed limiter (if equipped) for Your Nissan X Trail SUV Fourth Generation (2022-2026)

SPEED LIMITER (if equipped)  
The speed limiter allows you to set the desired  
vehicle speed limit. While the speed limiter is  
activated, the driver can perform normal brak-  
ing and acceleration, but the vehicle will not  
exceed the set speed.  
Action to take:  
objects such as ice, frost or dirt obstructing the  
radar sensors.  
When the above conditions no longer exist,  
the system will resume automatically.  
Check for and remove objects obstructing the  
area around the radar sensors.  
SYSTEM MALFUNCTION  
Do not attach stickers (including transparent  
material), install accessories or apply additional  
paint near the radar sensors.  
When the RCTA system malfunctions, it will turn  
off automatically. The “System fault” warning  
message will appear in the vehicle information  
display.  
WARNING:  
.
.
Always observe posted speed limits. Do  
not set the speed over them.  
Do not strike or damage the area around the  
radar sensors. It is recommended that you visit  
a NISSAN dealer if the area around the radar  
sensors is damaged due to a collision.  
NOTE:  
Always confirm the setting status of the  
speed limiter on the vehicle information  
display.  
If the BSW system stops working, the RCTA  
system will also stop working.  
For the radio approval numbers and informa-  
tion, see “Radio approval number and informa-  
tion” (P.9-15).  
Action to take:  
When the speed limiter is on, the cruise control  
(if equipped) system cannot be operated.  
Stop the vehicle in a safe location, turn the  
engine off and restart the engine. If the  
message continues to appear, have the system  
checked by a NISSAN dealer.  
SPEED LIMITER OPERATIONS  
The speed limiter can be set at  
between the following speeds.  
a
speed  
SYSTEM MAINTENANCE  
.
30 to 180 km/h (20 to 112 MPH) (for HR13  
and R9M engine models)  
.
30 to 200 km/h (20 to 124 MPH) (for M9R  
engine models)  
JVS0945X  
The two radar sensors  
for the RCTA systems  
are located near the rear bumper. Always keep  
the area near the radar sensors clean.  
WAF0491X  
The radar sensors may be blocked by tempor-  
ary ambient conditions such as splashing  
water, mist or fog.  
The speed limiter set switches are located on  
the steering wheel.  
1.  
RES/+ switch  
The blocked condition may also be caused by  
5-60 Starting and driving  
2.  
3.  
4.  
CANCEL switch  
SET/- switch  
The speed limiter will not automatically  
reduce the vehicle speed to the set speed  
limit.  
Canceling speed limit  
To cancel the speed limiter, push the CANCEL  
switch. The speed limiter indicator and the set  
speed indicator on the vehicle information  
display will turn off.  
Speed limiter MAIN switch (When this  
switch is pushed, the speed limiter enters  
the standby mode. If the cruise control or  
ICC system is on, the system will turn off  
and the speed limiter enters the standby  
mode.)  
Turning on speed limiter  
Push the speed limiter MAIN switch. The speed  
limiter and the set speed indicators illuminate  
on the vehicle information display.  
It is also possible to override the speed limiter  
by fully depressing the accelerator pedal be-  
yond the resistance point.  
5.  
Cruise ON/OFF switch (For details, see  
“Cruise control” (P.5-62).)  
Setting speed limit  
1. Push the SET/− switch.  
WARNING:  
.
When the vehicle is stopped, the speed  
will be set at 30 km/h or 20 MPH.  
.
.
The vehicle may accelerate when the  
speed limiter cancels.  
.
While driving, the speed limit will be set  
at the current speed.  
When additional floor mats are used, be  
sure that they are correctly secured and  
that they cannot interfere with the accel-  
erator pedal. Mats not adapted to the  
vehicle may prevent proper operation of  
the speed limiter.  
2. When the speed limit is set, the speed  
limiter indicator and the set speed indicator  
illuminate on the vehicle information dis-  
play.  
Fully depress the accelerator pedal beyond the  
resistance point. The speed limiter will be  
suspended to allow driving above the set  
speed. The set speed indicator will flash. The  
speed limiter will automatically resume when  
the vehicle speed drops below the set speed  
limit.  
Changing set speed limit:  
Use either of the following operations to  
change the speed limit.  
JVS0284X  
The speed limiter operating condition is shown  
on the vehicle information display.  
.
Push and hold the RES/+ or SET/- switch.  
The set speed will increase or decrease by  
approximately 5 km/h or 5 MPH.  
1.  
Speed limiter indicator  
Set speed indicator  
.
Push, then quickly release the RES/+ or  
SET/- switch. Each time you do this, the set  
speed will increase or decrease by approxi-  
mately 1 km/h or 1 MPH.  
2.  
Resuming a previous set speed  
The speed unit can be converted between  
“km/h” and “MPH”. (See “Vehicle information  
display” (P.2-21).)  
If a set speed limit has been cancelled, the set  
speed will be stored in the speed limiter  
memory.  
The new set speed limit value will be displayed  
in the vehicle information display.  
When the vehicle speed exceeds the set speed  
limit, the set speed indicator blinks and the  
accelerator pedal operation will not work until  
the vehicle speed slows down to the set speed  
limit.  
This speed limit can be reactivated by pressing  
the RES/+ switch upwards.  
When the actual vehicle speed exceeds the set  
speed, an audible warning will be heard a short  
time after the set speed is exceeded if driver  
intervention is not detected.  
If the current vehicle speed is higher than the  
previous set speed, the accelerator pedal will  
not work and the set speed indicator will flash  
until the vehicle speed drops below the set  
speed limit.  
When the actual vehicle speed exceeds the set  
Starting and driving 5-61  
CRUISE CONTROL (if equipped)  
speed, an audible warning will be heard a short  
time after the set speed is exceeded and driver  
intervention is not detected.  
control and result in an accident.  
— When it is not possible to keep the  
vehicle at a constant speed  
— When driving in heavy traffic  
Turning the speed limiter off  
— When driving in traffic that varies  
speed  
The speed limiter system will be turned off  
when one of the following operations is per-  
formed:  
— When driving in windy areas  
.
Push the speed limiter MAIN switch. The  
speed limiter indicator and the set speed  
indicator on the vehicle information display  
will be turned off.  
— When driving on winding or hilly roads  
— When driving on slippery (rain, snow,  
ice, etc.) roads  
JVS1005X  
(Model without speed limiter)  
.
Push the Cruise ON/OFF switch. The speed  
limiter information on the vehicle informa-  
tion will be replaced with the cruise control  
information. For details see “Cruise control”  
(P.5-62).  
CAUTION:  
On manual Transmission (MT) model, do not  
shift to the “N” (Neutral) position without  
depressing the clutch pedal when the cruise  
control is operated. Should this occur, de-  
press the clutch pedal and turn the Cruise  
ON/OFF switch off immediately. Failure to do  
so may cause engine damage.  
.
When the vehicle is stopped and the igni-  
tion switch is placed in the “OFF” position.  
Turning off the speed limiter will erase the set  
speed limit memory.  
Speed limiter malfunction  
PRECAUTIONS ON CRUISE CONTROL  
If the speed limiter malfunctions, the speed  
limiter on the vehicle information display will  
flash.  
.
If the cruise control system malfunctions, it  
will cancel automatically. The CRUISE in-  
dicator in the vehicle information display  
will then blink to warn the driver.  
WAF0492X  
(Model with speed limiter)  
RES/+ switch  
Turn the speed limiter MAIN switch off and  
have the system checked by a NISSAN dealer.  
CANCEL switch  
.
.
If the CRUISE indicator blinks, turn the  
Cruise ON/OFF switch off and have the  
system checked by a NISSAN dealer.  
SET/- switch  
Cruise ON/OFF switch  
Speed limiter MAIN switch  
The CRUISE indicator may blink when the  
Cruise ON/OFF switch is turned ON while  
pushing the ACCELERATE/RESUME or RES/  
+, COAST/SET or SET/- or CANCEL switch.  
To properly set the cruise control system,  
perform the following procedures.  
WARNING:  
.
.
Always observe the posted speed limits  
and do not set the speed over them.  
Do not use the cruise control when  
driving under the following conditions.  
Doing so could cause a loss of vehicle  
5-62 Starting and driving  

Related Topics

Starting and driving
Break-in schedule Push-button ignition switch (model with Intelligent Key system) Starting engine (model without Intelligent Key system) Starting engine (model with Intelligent Key system) Driving vehicle Stop/Start System or Idling Stop System (if equipped) Hill start assist system Hill descent control system (if equipped) Intelligent Lane Intervention (if equipped) Blind Spot Warning (BSW) (if equipped) Rear Cross Traffic Alert (RCTA) (if equipped) Cruise control (if equipped) Increasing fuel economy and reducing Carbon Dioxide emissions SPORT mode system (for Korea) ECO mode system (if equipped) Parking Trailer towing (except for Australia, New Zealand, South Africa, Argentina and Europe) Trailer towing (for Australia, New Zealand, South Africa, Argentina and Europe) Electric power steering Anti-lock Braking System (ABS) Vehicle security Cold weather driving

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot