Advertisement

Advertisement

Download User Manual App

Quickly access user manual for free!

READY TO SET OFF -> Service indicator for Your Peugeot Partner Van 2008-2014

Instruments and controls  
More than 1 000 miles/km before the A few seconds after the ignition is  
next service is due  
SERVICE INDICATOR  
switched on, the oil level is displayed,  
then the total distance recorder  
This programmes service intervals  
according to the use of the vehicle.  
Example: 4 800 miles/km remain  
before the next service is due. When  
the ignition is switched on and for a  
few seconds, the screen shows:  
resumes normal operation and the  
spanner remains on. This indicates that  
a service should be carried out shortly.  
Operation  
Service overdue  
A few moments after the ignition  
has been switched on, the spanner  
indicating a service operation comes  
on; the display for the total distance  
recorder gives (in round gures) the  
distance remaining before the next  
service.  
The points at which a service is due  
are calculated from the last indicator  
zero reset.  
Each time the ignition is  
switched on and for a few  
seconds, the spanner  
ashes and the excess  
distance is displayed.  
A few seconds after the ignition is  
switched on, the oil level is displayed,  
then the total distance recorder  
resumes normal operation showing the  
total and trip distances.  
With the engine running the  
spanner remains on until the  
service has been carried out.  
The point at which a service is due is  
determined by two parameters:  
-
-
the distance travelled,  
the time which has elapsed since  
the last service.  
Less than 1 000 miles/km before the  
next service is due  
Each time the ignition is switched on  
and for a few seconds, the spanner  
ashes and the number of miles/  
kilometres remaining is displayed:  
First of the two terms reached: the  
spanner also comes on if the two-year  
interval has elapsed.  
The distance remaining before the  
next service may be weighted by  
the time factor, depending on the  
type of driving.  
2
Instruments and controls  
Zero re-set  
Oil level correct  
Low oil level  
Dipstick  
A = maximum, never exceed  
this level as a surplus of oil  
may damage the engine.  
Contact a PEUGEOT dealer  
or a qualied workshop  
without delay.  
B = minimum, top up the level  
via the oil ller cap, using the  
grade of oil suited to your  
engine.  
Your PEUGEOT dealer or a qualied  
workshop carries out this operation  
after each service.  
However, if you carry out the service  
yourself, the re-set procedure is as  
follows:  
Flashing of "OIL",  
linked with the  
service warning lamp,  
-
-
switch off the ignition,  
press and hold the trip recorder  
reset button,  
switch on the ignition.  
accompanied by an  
audible signal and a message in the  
screen, indicates a low oil level which  
could damage the engine.  
-
The display begins a countdown.  
When the display shows "=0", release  
the button; the spanner disappears.  
If the low oil level is conrmed by a  
check using the dipstick, it is essential  
that the level is topped up.  
Trip recorder zero  
reset button  
With the ignition on, press  
the button until the zeros  
appear.  
After this operation, if you wish to  
disconnect the battery, lock the  
vehicle and wait for at least ve  
minutes, otherwise the zero re-set will  
not be registered.  
Oil level gauge fault  
Flashing of "OIL--"  
indicates a malfunction  
of the engine oil level  
indicator. Contact  
a PEUGEOT dealer or a qualied  
workshop.  
Lighting dimmer  
With the lighting on,  
press the button to vary  
the brightness of the  
The level read will only be correct  
if the vehicle is on level ground  
and the engine has been off for  
more than 30 minutes.  
Engine oil level indicator  
instruments and controls.  
When the lighting  
When the ignition is switched on, the  
engine oil level is indicated for a few  
seconds, after the service information.  
reaches the minimum (or  
maximum) setting, release  
the button then press it again to  
increase (or reduce) the brightness.  
As soon as the lighting is of the  
required brightness, release the button.