2010-2016 Renault Scenic 4 Door Getting to know your vehicle -> CHILD SAFETY: fitting a child seat User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Getting to know your vehicle -> CHILD SAFETY: fitting a child seat for Your Renault Scenic 4 Door Third Generation (2010-2016)

CHILD SAFETY: fitting a child seat (1/11)  
Some seats are not suitable for fitting  
child seats. The diagram on the follow-  
ing page shows you how to attach a  
child seat.  
In the front seat  
The laws concerning children travel-  
ling in the front passenger seat differ in  
every country. Consult the legislation in  
force and follow the indications on the  
diagram on the following page.  
The types of child seats indicated may  
not be available. Before using a differ-  
ent child seat, check with the manufac-  
turer that it can be fitted.  
Before fitting a child seat in this seat (if  
authorised):  
– lower the seat belt as far as possible;  
– move the seat as far back as possi-  
ble;  
– gently tilt the seatback away from  
vertical (approximately 25°);  
– on equipped vehicles, raise the seat  
base as far as possible.  
Fit the child seat in a rear  
seat wherever possible.  
Check that when installing  
the child seat in the vehicle  
it is not at risk of coming loose from  
its base.  
Do not change these settings after the  
child seat is installed.  
If you have to remove the headrest,  
check that it is correctly stored so  
that it does not come loose under  
harsh braking or impact.  
RISK OF DEATH OR  
SERIOUS INJURY: before  
fitting a rear-facing child  
seat to this seat, check  
that the air bag has been deacti-  
vated (refer to the information on  
“Child safety: deactivating/activat-  
ing the front passenger air bag” in  
Section 1).  
Always attach the child seat to the  
vehicle even if it is not in use so that  
it does not come loose under harsh  
braking or impact.  
1.35  
CHILD SAFETY: fitting a child seat (2/11)  
In the rear seat  
In the rear centre seat  
When fitting a child seat  
(Group 2 or 3 booster seat),  
check that the seat belts op-  
erate (wind) correctly: refer  
to Section 1 “Rear seat belts”. If  
necessary, adjust the position of the  
vehicle seat.  
A carrycot can be installed across the  
vehicle and will take up at least two  
seats. Position the child with his or her  
feet nearest the door.  
Some child seats are too wide to allow  
access to the seat belt buckles. Check  
that your child seat can be fitted in this  
seat.  
Move the front seat as far forward as  
possible to install a rear-facing child  
seat, then move back the seat in front  
as far as it will go, although without al-  
lowing it to come into contact with the  
child seat.  
When fitting an ISOFIX child seat in  
this place, ensure that the two seat  
belt buckles are placed flat under the  
child seat, except in the case of booster  
seats attached to the ISOFIX locks,  
whose fitting is authorised  
For the safety of the child in the for-  
ward-facing seat, do not move the seat  
in front back past the middle of the  
runner, do not tilt the seatback too far  
(maximum of 25°) and move the seat  
backwards as far as possible.  
Check that the child seat is resting  
against the back of the vehicle seat and  
that the headrest of the vehicle is not  
obstructing its use.  
The floor of your vehicle  
has storage spaces. Before  
installing a child seat with  
a floor support, ensure that  
this seat can be correctly installed  
by consulting the list of compatible  
vehicles supplied with the child seat.  
For 7-seater vehicles, the second row  
rear seats must be pushed forward  
before a child is seated in the third row  
rear seats.  
Ensure that the child seat  
or the child’s feet do not  
prevent the front seat from  
locking correctly. Refer to  
the information on the “Front seat”  
in Section 1 or “Rear seat operation”  
in Section 3.  
Risk of serious injury in the event of  
sudden braking or accident.  
1.36  
CHILD SAFETY: fitting a child seat (3/11)  
Child seat attached using the ISOFIX  
mounting  
ü
Seat which allows an ISOFIX  
child seat to be fitted.  
The rear seats are fitted with  
an anchorage point which allows a for-  
ward-facing ISOFIX child seat with uni-  
versal approval to be fitted. The anchor-  
ing points are visible on the floor behind  
the seat concerned or under the carpet,  
and indicated by a marking.  
The size of the ISOFIX child seat is in-  
dicated by a letter:  
– A, B and B1: for forward-facing seats  
in group 1 (9 to 18 kg);  
– C: rear-facing seat in group 1 (from 9  
to 18 kg);  
– D and E: shell seat or rear-facing  
seats in group 0 or 0+ (less than  
13 kg);  
– F and G: carrycots in group 0 (less  
than 10 kg).  
Child seat attached using the belt  
Seat which allows a child seat  
with “Universal” approval to be attached  
by a seat belt.  
Installation diagram,  
5-seater short chassis  
version  
¬
³
Check the status of the air bag  
−
Seat which only allows a rear-  
facing seat with “Universal” approval  
before fitting a child seat or allowing a  
passenger to use the seat.  
to be attached with a seat belt.  
²
Seat not suitable for fitting child  
seats.  
Using a child safety system  
which is not approved for  
this vehicle will not correctly  
protect the baby or child.  
They risk serious or even fatal injury.  
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child  
seat to the front passenger seat, check that the air bag has been deacti-  
vated (refer to the information on “Child safety: deactivating/activating the  
front passenger air bag” in Section 1).  
1.37  
CHILD SAFETY: fitting a child seat (4/11)  
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-  
tions in force are respected.  
Seat size  
Weight of  
the child  
Front passenger  
Rear centre  
seat  
Type of child seat  
Rear side seats  
seat (1) (5)  
ISOFIX  
Carrycot fitted across the vehicle  
Group 0  
< 10 kg  
F, G  
X
U - IL (2)  
U (2)  
E, D  
C
U
U
U - IL (3)  
U (3)  
U - IL (3)  
U (3)  
Shell seat/rear-facing seat  
Group 0, 0+ and 1  
< 13 kg and 9 to  
18 kg  
Forward-facing seat  
Group 1  
9 to 18 kg  
A, B, B1  
X
X
U - IUF - IL (4) U - IUF - IL (4)  
U (4) U (4)  
Booster seat  
Group 2 and 3  
15 to 25 kg and  
22 to 36 kg  
X = Seat not suitable for fitting child seats.  
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.  
IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be  
attached using the ISOFIX system; check that it can be fitted.  
(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,  
tilting the seatback slightly (approximately 25°).  
(2) A carrycot can be installed across the vehicle and will take up two seats. Position the child with his or her feet nearest the  
door.  
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it  
will go, although without allowing it to come into contact with the child seat.  
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the  
height of the headrest or remove it if necessary; do not push the seat in front of the child more than halfway back on its run-  
ners and do not recline the seatback more than 25°.  
(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in the front passenger seat, check  
that the air bag deactivator is in the OFF position.  
1.38  
CHILD SAFETY: fitting a child seat (5/11)  
Child seat attached using the ISOFIX  
mounting  
ü
Seat which allows an ISOFIX  
child seat to be fitted.  
The rear seats are fitted with  
an anchorage point which allows a for-  
ward-facing ISOFIX child seat with uni-  
versal approval to be fitted. The anchor-  
ing points are visible on the floor behind  
the seat concerned or under the carpet,  
and indicated by a marking.  
The size of the ISOFIX child seat is in-  
dicated by a letter:  
– A, B and B1: for forward-facing seats  
in group 1 (9 to 18 kg);  
– C: rear-facing seat in group 1 (from 9  
to 18 kg);  
– D and E: shell seat or rear-facing  
seats in group 0 or 0+ (less than  
13 kg);  
– F and G: carrycots in group 0 (less  
than 10 kg).  
Child seat attached using the belt  
Seat which allows a child seat  
with “Universal” approval to be attached  
by a seat belt.  
Installation diagram,  
5-seater long chassis  
version  
¬
³
Check the status of the air bag  
−
Seat which only allows a rear-  
facing seat with “Universal” approval  
before fitting a child seat or allowing a  
passenger to use the seat.  
to be attached with a seat belt.  
²
Seat not suitable for fitting child  
seats.  
Using a child safety system  
which is not approved for  
this vehicle will not correctly  
protect the baby or child.  
They risk serious or even fatal injury.  
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child  
seat to the front passenger seat, check that the air bag has been deacti-  
vated (refer to the information on “Child safety: deactivating/activating the  
front passenger air bag” in Section 1).  
1.39  
CHILD SAFETY: fitting a child seat (6/11)  
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-  
tions in force are respected.  
Seat size  
Weight of  
the child  
Front passenger  
Rear centre  
seat  
Type of child seat  
Rear side seats  
seat (1) (5)  
ISOFIX  
Carrycot fitted across the  
vehicle  
< 10 kg  
F, G  
X
U - IL (2)  
U (2)  
Group 0  
E, D  
C
U
U
U - IL (3)  
U - IL (3)  
U - IL (3)  
U - IL (3)  
Shell seat/rear-facing seat  
Group 0, 0+ and 1  
< 13 kg and 9 to  
18 kg  
Forward-facing seat  
Group 1  
9 to 18 kg  
A, B, B1  
X
X
U - IUF - IL (4)  
U (4)  
U- IUF - IL (4)  
U (4)  
Booster seat  
Group 2 and 3  
15 to 25 kg and  
22 to 36 kg  
X = Seat not suitable for fitting child seats.  
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.  
IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be  
attached using the ISOFIX system; check that it can be fitted.  
(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,  
tilting the seatback slightly (approximately 25°).  
(2) A carrycot can be installed across the vehicle and will take up two seats. Position the child with his or her feet nearest the  
door.  
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it  
will go, although without allowing it to come into contact with the child seat.  
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the  
height of the headrest or remove it if necessary; do not push the seat in front of the child more than halfway back on its run-  
ners and do not recline the seatback more than 25°.  
(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in the front passenger seat, check  
that the air bag deactivator is in the OFF position.  
1.40  
CHILD SAFETY: fitting a child seat (7/11)  
Child seat attached using the ISOFIX  
mounting  
ü
Seat which allows an ISOFIX  
child seat to be fitted.  
The rear seats are fitted with  
an anchorage point which allows a  
forward-facing ISOFIX child seat with  
universal approval to be fitted. The an-  
choring points are located on the floor  
behind the seat concerned and indi-  
cated by a marking.  
The size of the ISOFIX child seat is in-  
dicated by a letter:  
– A, B and B1: for forward-facing seats  
in group 1 (9 to 18 kg);  
– C: rear-facing seat in group 1 (from 9  
to 18 kg);  
– D and E: shell seat or rear-facing  
seats in group 0 or 0+ (less than  
13 kg);  
– F and G: carrycots in group 0 (less  
than 10 kg).  
Child seat attached using the belt  
Seat which allows a child seat  
with “Universal” approval to be attached  
by a seat belt.  
Installation diagram,  
7-seater version  
³
¬
Check the status of the air bag  
before fitting a child seat or allowing a  
passenger to use the seat.  
−
Seat which only allows a rear-  
facing seat with “Universal” approval  
²
Seat not suitable for fitting child  
to be attached with a seat belt.  
seats.  
Using a child safety system  
which is not approved for  
this vehicle will not correctly  
protect the baby or child.  
They risk serious or even fatal injury.  
(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing  
child seat in the front passenger seat, check that the air bag deactivator  
is in the OFF position.  
1.41  
CHILD SAFETY: fitting a child seat (8/11)  
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-  
tions in force are respected.  
Front  
passenger  
seat (1) (6)  
Seat size  
Weight of  
the child  
Row 2 rear  
side seats  
Row 2 rear  
centre seat  
Row 3 rear  
seats (5)  
Type of child seat  
ISOFIX  
Carrycot fitted  
across the vehi-  
cle  
< 10 kg  
F, G  
X
U - IL (2)  
U (2)  
U
Group 0  
E, D  
C
U
U
U - IL (3)  
U - IL (3)  
U - IL (3)  
U - IL (3)  
U
U
Shell seat/rear-  
facing seat  
Group 0, 0+ and 1  
< 13 kg and  
9 to 18 kg  
Forward-facing  
seat  
Group 1  
9 to 18 kg  
A, B, B1  
X
X
U - IUF - IL (4) U - IUF - IL (4)  
U
U
15 to 25 kg  
and 22 to  
36 kg  
Booster seat  
Group 2 and 3  
U (4)  
U (4)  
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat to the front passenger seat, check that  
the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front passenger  
air bag” in Section 1).  
1.42  
CHILD SAFETY: fitting a child seat (9/11)  
X = Seat not suitable for fitting child seats.  
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.  
IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at-  
tached using the ISOFIX system; check that it can be fitted.  
(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,  
tilting the seatback slightly (approximately 25°).  
(2) A carrycot can be installed across the vehicle and will take up two seats. Position the child with his or her feet nearest the door.  
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will  
go, although without allowing it to come into contact with the child seat.  
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the  
height of the headrest or remove it if necessary; do not push the seat in front of the child more than halfway back on its runners  
and do not recline the seatback more than 25°.  
(5) Push the seat(s) in front of the child in a third row seat as far forward as possible.  
(6) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in the front passenger seat, check  
that the air bag deactivator is in the OFF position.  
1.43  
CHILD SAFETY: fitting a child seat (10/11)  
Child seat attached using the ISOFIX  
mounting  
ü
Seat which allows an ISOFIX  
child seat to be fitted.  
The rear seats are fitted with  
an anchorage point which allows a for-  
ward-facing ISOFIX child seat with uni-  
versal approval to be fitted. The anchor-  
ing points are visible on the floor behind  
the seat concerned or under the carpet,  
and indicated by a marking.  
The size of the ISOFIX child seat is in-  
dicated by a letter:  
– A, B and B1: for forward-facing seats  
in group 1 (9 to 18 kg);  
– C: rear-facing seat in group 1 (from 9  
to 18 kg);  
– D and E: shell seat or rear-facing  
seats in group 0 or 0+ (less than  
13 kg);  
– F and G: carrycots in group 0 (less  
than 10 kg).  
Child seat attached using the belt  
Seat which allows a child seat  
with “Universal” approval to be attached  
by a seat belt.  
View of four-seater version  
installation  
¬
³
Check the status of the air bag  
before fitting a child seat or allowing a  
passenger to use the seat.  
−
Seat which only allows a rear-  
facing seat with “Universal” approval  
²
Seat not suitable for fitting child  
to be attached with a seat belt.  
seats.  
Using a child safety system  
which is not approved for  
this vehicle will not correctly  
protect the baby or child.  
They risk serious or even fatal injury.  
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child  
seat to the front passenger seat, check that the air bag has been deacti-  
vated (refer to the information on “Child safety: deactivating/activating the  
front passenger air bag” in Section 1).  
1.44  
CHILD SAFETY: fitting a child seat (11/11)  
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-  
tions in force are respected.  
Seat size  
Weight of  
the child  
Front passenger  
Type of child seat  
Rear side seats  
seat (1) (5)  
ISOFIX  
Carrycot fitted across the ve-  
hicle  
< 10 kg  
F, G  
X
U - IL (2)  
Group 0  
E, D  
C
U
U
U - IL (3)  
U - IL (3)  
Shell seat/rear-facing seat  
Group 0, 0+ and 1  
< 13 kg and 9 to  
18 kg  
Forward-facing seat  
Group 1  
9 to 18 kg  
A, B, B1  
X
X
U - IUF - IL (4)  
U (4)  
Booster seat  
Group 2 and 3  
15 to 25 kg and  
22 to 36 kg  
X = Seat not suitable for fitting child seats.  
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.  
IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be  
attached using the ISOFIX system; check that it can be fitted.  
(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,  
tilting the seatback slightly (approximately 25°).  
(2) A carrycot can be installed across the vehicle and will take up two seats. Position the child with his or her feet nearest the  
door.  
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it  
will go, although without allowing it to come into contact with the child seat.  
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the  
height of the headrest or remove it if necessary; do not push the seat in front of the child more than halfway back on its run-  
ners and do not recline the seatback more than 25°.  
(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in the front passenger seat, check  
that the air bag deactivator is in the OFF position.  
1.45  

Related Topics

Popular Owner Manuals