2017-2022 Subaru XV SUV Seat, seatbelt and SRS airbags -> Seatbelts User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Seat, seatbelt and SRS airbags -> Seatbelts for Your Subaru XV SUV Second Generation (2017-2022)

1-12Seat, seatbelt and SRS airbags/SeatbeltsSeatbeltsreversed. In an accident, this canincrease the risk or severity ofS01AE& Seatbelt safety tipsinjury.S01AE01. Keep the lap belt as low asWARNINGpossible on your hips. In a colli-sion, this spreads the force of the. All persons in the vehicle shouldlap belt over stronger hip bonesfasten their seatbelts BEFOREinstead of across the weakerthe vehicle starts to move. , the possibility of serious. Seatbelts provide maximum re-injury becomes greater in thestraint when the occupant sitsevent of a sudden stop or acci-well back and upright in the reduce the risk of sliding. All belts should fit snugly in orderunder the seatbelt in a collision,WARNINGto provide full restraint. Loosethe front seatbacks should befitting belts are not as effective inalways used in the upright posi-Never place the shoulder belt underpreventing or reducing while the vehicle is arm or behind the back. If an. Each seatbelt is designed to sup-If the front seatbacks are notaccident occurs, this can increaseport only one person. Never use aused in the upright position in athe risk or severity of belt for two or more per-collision, the risk of sliding undersons 3 even children. Otherwise,the lap belt and of the lap beltCAUTIONin an accident, serious injury orsliding up over the abdomen willdeath could , and both can result inMetallic parts of the seatbelt canserious internal injury or death.. Replace all seatbelt assembliesbecome very hot in a vehicle that hasincluding retractors and attach-. Do not put cushions or any otherbeen closed up in sunny weather;ing hardware worn by occupantsmaterials between occupantsthey could burn an occupant. Do notof a vehicle that has been in aand seatbacks or seat such hot parts until they accident. The entire as-If you do so, the risk of slidingsembly should be replaced evenunder the lap belt and of the lapYo
1-12
Seat, seatbelt and SRS airbags/Seatbelts
Seatbelts
reversed. In an accident, this can
increase the risk or severity of
S01AE
& Seatbelt safety tips
injury.
S01AE01
. Keep the lap belt as low as
WARNING
possible on your hips. In a colli-
sion, this spreads the force of the
. All persons in the vehicle should
lap belt over stronger hip bones
fasten their seatbelts BEFORE
instead of across the weaker
the vehicle starts to move. Other-
abdomen.
wise, the possibility of serious
. Seatbelts provide maximum re-
injury becomes greater in the
straint when the occupant sits
event of a sudden stop or acci-
well back and upright in the seat.
dent.
To reduce the risk of sliding
. All belts should fit snugly in order
under the seatbelt in a collision,
WARNING
to provide full restraint. Loose
the front seatbacks should be
fitting belts are not as effective in
always used in the upright posi-
Never place the shoulder belt under
preventing or reducing injury.
tion while the vehicle is running.
the arm or behind the back. If an
. Each seatbelt is designed to sup-
If the front seatbacks are not
accident occurs, this can increase
port only one person. Never use a
used in the upright position in a
the risk or severity of injury.
single belt for two or more per-
collision, the risk of sliding under
sons 3 even children. Otherwise,
the lap belt and of the lap belt
CAUTION
in an accident, serious injury or
sliding up over the abdomen will
death could result.
increase, and both can result in
Metallic parts of the seatbelt can
serious internal injury or death.
. Replace all seatbelt assemblies
become very hot in a vehicle that has
including retractors and attach-
. Do not put cushions or any other
been closed up in sunny weather;
ing hardware worn by occupants
materials between occupants
they could burn an occupant. Do not
of a vehicle that has been in a
and seatbacks or seat cushions.
touch such hot parts until they cool.
serious accident. The entire as-
If you do so, the risk of sliding
sembly should be replaced even
under the lap belt and of the lap
Your vehicle is equipped with a crash
if damage is not obvious.
belt sliding up over the abdomen
sensing and diagnostic module, which will
will increase, and both can result
. Never use a belt that is twisted or
record the use of the seatbelt by the front
in serious internal injury or death.
1-13Seat, seatbelt and SRS airbags/Seatbeltspassenger when any of the SRS frontal,waist. If the shoulder portion of the and curtain airbags be properly positioned, a childNEVER INSTALL A FORWARD ORrestraint system should be used. NeverREARWARD FACING CHILD SEAT IN! Infants or small childrenplace the shoulder belt under the child9sTHE FRONT SEAT. DOING SO RISKSS01AE0101Use a child restraint system that is suitablearm or behind the child9s INJURY OR DEATH TOfor your vehicle. Refer to <Child restraintTHE CHILD BY PLACING THE! Expectant motherssystems= 9S HEAD TOO CLOSE TOS01AE0103! ChildrenTHE SRS AIRBAG.S01AE0102According to accident statistics,WARNINGchildren are safer when properlyrestrained in the rear seating posi-Place children in the rear seat prop-tions than in the front seating posi-erly restrained at all times. The SRStions. For instructions and precau-airbag deploys with considerabletions concerning the child restraintspeed and force and can injure orsystem, refer to <Child restrainteven kill children, especially if theysystems= not restrained or improperlyrestrained. Because children areIf a child is too big for a child restraintlighter and weaker than adults, theirsystem, the child should sit in the rear seatrisk of being injured from deploy-and be restrained using the mothers also need to use thement is greater. For that reason, weAccording to accident statistics, childrenseatbelts. They should consult their doctorstrongly recommend that ALL chil-are safer when properly restrained in thefor specific recommendations. The lap beltdren (including those in child seatsrear seating positions than in the frontshould be worn securely and as low asand those that have outgrown childseating positions. Never allow a child topossible over the hips, not over the devices) sit in the REARstand up or kneel on the properly restrained at all timesin a child restraint
1-13
Seat, seatbelt and SRS airbags/Seatbelts
passenger when any of the SRS frontal,
waist. If the shoulder portion of the belt
times.
side and curtain airbags deploy.
cannot be properly positioned, a child
NEVER INSTALL A FORWARD OR
restraint system should be used. Never
REARWARD FACING CHILD SEAT IN
! Infants or small children
place the shoulder belt under the child9s
THE FRONT SEAT. DOING SO RISKS
S01AE0101
Use a child restraint system that is suitable
arm or behind the child9s back.
SERIOUS INJURY OR DEATH TO
for your vehicle. Refer to <Child restraint
THE CHILD BY PLACING THE
! Expectant mothers
systems= F1-25.
CHILD9S HEAD TOO CLOSE TO
S01AE0103
! Children
THE SRS AIRBAG.
S01AE0102
According to accident statistics,
WARNING
children are safer when properly
restrained in the rear seating posi-
Place children in the rear seat prop-
tions than in the front seating posi-
erly restrained at all times. The SRS
tions. For instructions and precau-
airbag deploys with considerable
tions concerning the child restraint
speed and force and can injure or
system, refer to <Child restraint
even kill children, especially if they
systems= F1-25.
are not restrained or improperly
restrained. Because children are
If a child is too big for a child restraint
lighter and weaker than adults, their
system, the child should sit in the rear seat
risk of being injured from deploy-
and be restrained using the seatbelts.
Expectant mothers also need to use the
ment is greater. For that reason, we
According to accident statistics, children
seatbelts. They should consult their doctor
strongly recommend that ALL chil-
are safer when properly restrained in the
for specific recommendations. The lap belt
dren (including those in child seats
rear seating positions than in the front
should be worn securely and as low as
and those that have outgrown child
seating positions. Never allow a child to
possible over the hips, not over the waist.
restraint devices) sit in the REAR
stand up or kneel on the seat.
seat properly restrained at all times
in a child restraint device or in a
If the shoulder portion of the belt crosses
seatbelt, whichever is appropriate
the face or neck, move the child closer to
for the child9s height and weight.
the belt buckle to help provide a good
shoulder belt fit. Care must be taken to
Secure ALL types of child restraint
securely place the lap belt as low as
devices (including forward facing
possible on the hips and not on the child9s
child seats) in the REAR seats at all
3 CONTINUED 3
1-14Seat, seatbelt and SRS airbags/Seatbelts& Emergency Locking Retrac-the rear seats by the use of the seatbelt,2. Sit well back in the (ELR)the seatbelt must be changed over to the3. Pick up the tongue plate and pull theAutomatic Locking Retractor (ALR) out slowly. Do not let it get twisted.S01AE02The driver9s seatbelt has an Emergency. If the belt stops before reaching theLocking Retractor (ELR).When the child restraint system is re-buckle, return the belt slightly and pull itmoved, make sure that the seatbelt re-The emergency locking retractor allowsout more fully and the retractor returned to thenormal body movement but the retractor. If the belt still cannot be unlocked, letEmergency Locking Retractor (ELR)locks automatically during a sudden stop,the belt retract slightly after giving it or if you pull the belt very quicklystrong pull, then pull it out slowly of the instructions on how to convert theretractor to the ALR mode and restore it to& Automatic Locking Retractor/the ELR mode, refer to <Installing childEmergency Locking Retrac-restraint systems with ALR/ELR seatbelt=tor (ALR/ELR)F1-28.S01AE03Each passenger9s seatbelt has an Auto-& Seatbelt warning lightmatic Locking Retractor/Emergency Lock-and chimeing Retractor (ALR/ELR). The AutomaticS01AE04Locking Retractor/Emergency LockingRefer to <Seatbelt warning light and chime=Retractor normally functions as an Locking Retractor (ELR). The ALR/ELR has an additional locking mode& Fastening the seatbelt<Automatic Locking Retractor (ALR)S01AE06! Front seatbeltsmode= intended to secure a child restraintS01AE0601system. When the seatbelt is once drawn4. Insert the tongue plate into the buckle1. Adjust the seat position according toout completely and is then retracted evenuntil you hear a following , the retractor locks the seatbelt inDriver9s seat: Adjust the seatback to thethat position and the seatb
1-14
Seat, seatbelt and SRS airbags/Seatbelts
& Emergency Locking Retrac-
the rear seats by the use of the seatbelt,
2. Sit well back in the seat.
tor (ELR)
the seatbelt must be changed over to the
3. Pick up the tongue plate and pull the
Automatic Locking Retractor (ALR) mode.
belt out slowly. Do not let it get twisted.
S01AE02
The driver9s seatbelt has an Emergency
. If the belt stops before reaching the
Locking Retractor (ELR).
When the child restraint system is re-
buckle, return the belt slightly and pull it
moved, make sure that the seatbelt re-
The emergency locking retractor allows
out more slowly.
tracts fully and the retractor returned to the
normal body movement but the retractor
. If the belt still cannot be unlocked, let
Emergency Locking Retractor (ELR)
locks automatically during a sudden stop,
the belt retract slightly after giving it a
mode.
impact or if you pull the belt very quickly
strong pull, then pull it out slowly again.
out of the retractor.
For instructions on how to convert the
retractor to the ALR mode and restore it to
& Automatic Locking Retractor/
the ELR mode, refer to <Installing child
Emergency Locking Retrac-
restraint systems with ALR/ELR seatbelt=
tor (ALR/ELR)
F1-28.
S01AE03
Each passenger9s seatbelt has an Auto-
& Seatbelt warning light
matic Locking Retractor/Emergency Lock-
and chime
ing Retractor (ALR/ELR). The Automatic
S01AE04
Locking Retractor/Emergency Locking
Refer to <Seatbelt warning light and chime=
Retractor normally functions as an Emer-
F3-13.
gency Locking Retractor (ELR). The ALR/
ELR has an additional locking mode
& Fastening the seatbelt
<Automatic Locking Retractor (ALR)
S01AE06
! Front seatbelts
mode= intended to secure a child restraint
S01AE0601
system. When the seatbelt is once drawn
4. Insert the tongue plate into the buckle
1. Adjust the seat position according to
out completely and is then retracted even
until you hear a click.
the following procedure.
slightly, the retractor locks the seatbelt in
Driver9s seat: Adjust the seatback to the
that position and the seatbelt cannot be
upright position. Move the seat as far from
extended. As the belt is rewinding, clicks
the steering wheel as practical while still
will be heard which indicate the retractor
maintaining full vehicle control.
functions as an ALR. When the seatbelt is
Front passenger9s seat: Adjust the seat-
retracted fully, the ALR mode is released.
back to the upright position. Move the seat
When securing a child restraint system on
as far back as possible.
1-15Seat, seatbelt and SRS airbags/Seatbelts! Adjusting the front seat shoulderWARNINGbelt anchor heightWhen wearing the seatbelts, makeS01AE060101sure the shoulder portion of thewebbing does not pass over yourneck. If it does, adjust the seatbeltanchor to a lower position. Placingthe shoulder belt over the neck mayresult in neck injury during suddenbraking or in a collision.! Unfastening the seatbeltS01AE0601025. To make the lap part tight, pull up onthe shoulder belt.6. Place the lap belt as low as possible onThe shoulder belt anchor height should beyour hips, not on your to the position best suited for thedriver/front passenger. Always adjust theanchor height so that the shoulder beltpasses over the middle of the shoulderwithout touching the raise:Pull the release knob and slide the lower:1. Push the button on the the release knob and slide the anchor2. Have the seatbelt retracted slowly the seatbelt being tangled or down on the anchor to make sure thatBefore closing the door, make sure that theit is locked in are retracted properly to avoidcatching the belt webbing in the door.3 CONTINUED 3
1-15
Seat, seatbelt and SRS airbags/Seatbelts
! Adjusting the front seat shoulder
WARNING
belt anchor height
When wearing the seatbelts, make
S01AE060101
sure the shoulder portion of the
webbing does not pass over your
neck. If it does, adjust the seatbelt
anchor to a lower position. Placing
the shoulder belt over the neck may
result in neck injury during sudden
braking or in a collision.
! Unfastening the seatbelt
S01AE060102
5. To make the lap part tight, pull up on
the shoulder belt.
6. Place the lap belt as low as possible on
The shoulder belt anchor height should be
your hips, not on your waist.
adjusted to the position best suited for the
driver/front passenger. Always adjust the
anchor height so that the shoulder belt
passes over the middle of the shoulder
without touching the neck.
To raise:
Pull the release knob and slide the anchor
up.
To lower:
1. Push the button on the buckle.
Pull the release knob and slide the anchor
2. Have the seatbelt retracted slowly to
down.
avoid the seatbelt being tangled or twisted.
Pull down on the anchor to make sure that
Before closing the door, make sure that the
it is locked in place.
belts are retracted properly to avoid
catching the belt webbing in the door.
3 CONTINUED 3
1-16Seat, seatbelt and SRS airbags/Seatbelts! Rear seatbelts (except rear center! Unfastening the seatbeltseatbelt)S01AE060201S01AE06021. Sit well back in the seat.2. Pick up the tongue plate and pull thebelt out slowly. Do not let it get twisted.. If the belt stops before reaching thebuckle, return the belt slightly and pull itout more slowly.. If the belt still cannot be unlocked, letthe belt retract slightly after giving it astrong pull, then pull it out slowly again.4. To make the lap part tight, pull up onthe shoulder belt.1. Push the button on the buckle.5. Place the lap belt as low as possible on2. Have the seatbelt retracted slowly toyour hips, not on your the seatbelt being tangled or closing the door, make sure that thebelts are retracted properly to avoidcatching the belt webbing in the door.3. Insert the tongue plate into the buckleuntil you hear a click.
1-16
Seat, seatbelt and SRS airbags/Seatbelts
! Rear seatbelts (except rear center
! Unfastening the seatbelt
seatbelt)
S01AE060201
S01AE0602
1. Sit well back in the seat.
2. Pick up the tongue plate and pull the
belt out slowly. Do not let it get twisted.
. If the belt stops before reaching the
buckle, return the belt slightly and pull it
out more slowly.
. If the belt still cannot be unlocked, let
the belt retract slightly after giving it a
strong pull, then pull it out slowly again.
4. To make the lap part tight, pull up on
the shoulder belt.
1. Push the button on the buckle.
5. Place the lap belt as low as possible on
2. Have the seatbelt retracted slowly to
your hips, not on your waist.
avoid the seatbelt being tangled or twisted.
Before closing the door, make sure that the
belts are retracted properly to avoid
catching the belt webbing in the door.
3. Insert the tongue plate into the buckle
until you hear a click.
1-17Seat, seatbelt and SRS airbags/Seatbelts! Rear center seatbeltWARNINGWARNINGS01AE0603Fastening the seatbelt with the web-. Be sure to fasten both tonguebing twisted can increase the risk orplates to the respective of injury in an the seatbelt is used only as aWhen fastening the belt after it isshoulder belt (with the connec-pulled out from the retractor, espe-tor9s tongue plate not fastened tocially when inserting the connec-the connector9s buckle on thetor9s tongue plate into the matingright-hand side), it cannot prop-buckle (on right-hand side), alwayserly restrain the wearer in posi-check that the webbing is nottion in an accident, in serious injury ordeath.. The head restraint is not intended1)Center seatbelt tongue plateto be used at the lowest position.2)Connector (tongue)Before sitting on the seat, raise3)Connector (buckle)the head restraint to the extended4)Center seatbelt buckleposition. Otherwise, in an acci-dent, serious injury or deathcould result.3 CONTINUED 3
1-17
Seat, seatbelt and SRS airbags/Seatbelts
! Rear center seatbelt
WARNING
WARNING
S01AE0603
Fastening the seatbelt with the web-
. Be sure to fasten both tongue
bing twisted can increase the risk or
plates to the respective buckles.
severity of injury in an accident.
If the seatbelt is used only as a
When fastening the belt after it is
shoulder belt (with the connec-
pulled out from the retractor, espe-
tor9s tongue plate not fastened to
cially when inserting the connec-
the connector9s buckle on the
tor9s tongue plate into the mating
right-hand side), it cannot prop-
buckle (on right-hand side), always
erly restrain the wearer in posi-
check that the webbing is not
tion in an accident, possibly
twisted.
resulting in serious injury or
death.
. The head restraint is not intended
1)
Center seatbelt tongue plate
to be used at the lowest position.
2)
Connector (tongue)
Before sitting on the seat, raise
3)
Connector (buckle)
the head restraint to the extended
4)
Center seatbelt buckle
position. Otherwise, in an acci-
dent, serious injury or death
could result.
3 CONTINUED 3
PDF page
1-19Seat, seatbelt and SRS airbags/Seatbelts7. Place the lap belt as low as possible onyour hips, not on your waist.! Unfastening the seatbeltS01AE0603015. Insert the center seatbelt tongue plate2. Insert a tongue plate or other hardinto the center seatbelt buckle markedpointed object into the slot in the connector<CENTER= on the left-hand side until it(buckle) on the right-hand side and push . The connector (tongue) plate will thendisconnect from the buckle.1. Push the release button of the centerseatbelt buckle (on the left-hand side) tounfasten the the seatback is folded down forgreater cargo area, it is necessary todisconnect the connector.6. To make the lap part tight, pull up onthe shoulder belt.3 CONTINUED 3
1-19
Seat, seatbelt and SRS airbags/Seatbelts
7. Place the lap belt as low as possible on
your hips, not on your waist.
! Unfastening the seatbelt
S01AE060301
5. Insert the center seatbelt tongue plate
2. Insert a tongue plate or other hard
into the center seatbelt buckle marked
pointed object into the slot in the connector
<CENTER= on the left-hand side until it
(buckle) on the right-hand side and push it
clicks.
in. The connector (tongue) plate will then
disconnect from the buckle.
1. Push the release button of the center
seatbelt buckle (on the left-hand side) to
unfasten the seatbelt.
NOTE
When the seatback is folded down for
greater cargo area, it is necessary to
disconnect the connector.
6. To make the lap part tight, pull up on
the shoulder belt.
3 CONTINUED 3
1-20Seat, seatbelt and SRS airbags/Seatbelts& Seatbelt maintenanceS01AE07To clean the seatbelts, use a mild soap andlukewarm water. Never bleach or dye thebelts because this could seriously affecttheir the seatbelts and attachmentsincluding the webbing and all hardwareperiodically for cracks, cuts, gashes, tears,damage, loose bolts or worn areas. Re-place the seatbelts even if only minordamage is . Keep the belts free of polishes,oils, chemicals and particularly. Do not allow the retractor to rollbattery the seatbelt too quickly. Other-wise, the metal tongue plates. Never attempt to make modifica-may hit against the trim, resultingtions or changes that will preventin damaged seatbelt from operating prop-erly.. Have the seatbelt fully rolled upso that the tongue plates areneatly stored. A hanging tongueplate can swing and hit againstthe trim during driving, causing3. Allow the retractor to roll up the to the should hold the webbing end andguide it back into the retractor while it isrolling up. Insert the connector (tongue)into the belt holder.
1-20
Seat, seatbelt and SRS airbags/Seatbelts
& Seatbelt maintenance
S01AE07
To clean the seatbelts, use a mild soap and
lukewarm water. Never bleach or dye the
belts because this could seriously affect
their strength.
Inspect the seatbelts and attachments
including the webbing and all hardware
periodically for cracks, cuts, gashes, tears,
damage, loose bolts or worn areas. Re-
place the seatbelts even if only minor
damage is found.
CAUTION
CAUTION
. Keep the belts free of polishes,
oils, chemicals and particularly
. Do not allow the retractor to roll
battery acid.
up the seatbelt too quickly. Other-
wise, the metal tongue plates
. Never attempt to make modifica-
may hit against the trim, resulting
tions or changes that will prevent
in damaged trim.
the seatbelt from operating prop-
erly.
. Have the seatbelt fully rolled up
so that the tongue plates are
neatly stored. A hanging tongue
plate can swing and hit against
the trim during driving, causing
3. Allow the retractor to roll up the belt.
damage to the trim.
You should hold the webbing end and
guide it back into the retractor while it is
rolling up. Insert the connector (tongue)
into the belt holder.
1-21Seat, seatbelt and SRS airbags/Seatbelt pretensionersSeatbelt pretensionersas SUBARU dealer.. When you sell your vehicle, we urge. When discarding seatbelt retrac-S01AFyou to inform the buyer that the vehicletor assemblies equipped withThe following seatbelts have a seatbeltis equipped with seatbelt preten-seatbelt pretensioners or . Also, notify the buyer of theping the entire vehicle due to. Driver9s seatbeltcontents in this damage or for other. Front passenger9s seatbeltreasons, consult your SUBARU& Seatbelt with shoulder seatbelt pretensioners are designedpretensionerto be activated in the event of an accidentS01AF01involving a moderate to severe frontal andNOTENOTEside collision and rollover section is applicable to the follow-. Seatbelt pretensioners are not de-ing to activate in minor impacts or. Driver9s seatbeltin rear impacts.. To obtain maximum protection,. Pretensioners are designed to func-the occupants should sit in antion on a one-time-only basis. In theupright position with their seat-event that a pretensioner is activated,belts properly fastened. Refer toboth the driver9s and front passenger9s<Seatbelts= retractor assemblies shouldbe replaced only by an authorized. Do not modify, remove or strikeSUBARU dealer. When replacing seat-the seatbelt retractor assembliesbelt retractor assemblies, use onlyequipped with seatbelt preten-genuine SUBARU or surrounding area. This. If a seatbelt that has a seatbeltcould result in accidental activa-pretensioner does not retract or cannottion of the seatbelt pretensionersbe pulled out due to a malfunction oror could make the system inop-activation of the pretensioner, contacterative, possibly resulting in ser-your SUBARU dealer as soon as pos-ious injury. Seatbelt preten-Front seatbelt have no user-serviceableThe pretensioner sensor also serves as.
1-21
Seat, seatbelt and SRS airbags/Seatbelt pretensioners
Seatbelt pretensioners
as possible.
your SUBARU dealer.
. When you sell your vehicle, we urge
. When discarding seatbelt retrac-
S01AF
you to inform the buyer that the vehicle
tor assemblies equipped with
The following seatbelts have a seatbelt
is equipped with seatbelt preten-
seatbelt pretensioners or scrap-
pretensioner.
sioners. Also, notify the buyer of the
ping the entire vehicle due to
. Driver9s seatbelt
contents in this section.
collision damage or for other
. Front passenger9s seatbelt
reasons, consult your SUBARU
& Seatbelt with shoulder belt
dealer.
The seatbelt pretensioners are designed
pretensioner
to be activated in the event of an accident
S01AF01
involving a moderate to severe frontal and
NOTE
NOTE
side collision and rollover accident.
This section is applicable to the follow-
. Seatbelt pretensioners are not de-
ing components.
WARNING
signed to activate in minor impacts or
. Driver9s seatbelt
in rear impacts.
. To obtain maximum protection,
. Pretensioners are designed to func-
the occupants should sit in an
tion on a one-time-only basis. In the
upright position with their seat-
event that a pretensioner is activated,
belts properly fastened. Refer to
both the driver9s and front passenger9s
<Seatbelts= F1-12.
seatbelt retractor assemblies should
be replaced only by an authorized
. Do not modify, remove or strike
SUBARU dealer. When replacing seat-
the seatbelt retractor assemblies
belt retractor assemblies, use only
equipped with seatbelt preten-
genuine SUBARU parts.
sioners or surrounding area. This
. If a seatbelt that has a seatbelt
could result in accidental activa-
pretensioner does not retract or cannot
tion of the seatbelt pretensioners
be pulled out due to a malfunction or
or could make the system inop-
activation of the pretensioner, contact
erative, possibly resulting in ser-
your SUBARU dealer as soon as pos-
ious injury. Seatbelt preten-
Front seatbelt pretensioner
sible.
sioners have no user-serviceable
The pretensioner sensor also serves as
. If the seatbelt retractor assembly or
parts. For required servicing of
follows.
surrounding area has been damaged,
seatbelt retractors equipped with
. SRS frontal airbag sensor
contact your SUBARU dealer as soon
seatbelt pretensioners, consult
3 CONTINUED 3

Related Topics

Popular Owner Manuals