Get OPERATING YOUR VEHICLE -> SUZUKI SAFETY SUPPORT (if equipped) Guide for Suzuki Jimny SUV Fourth Generation (2018-2026)

OPERATING YOUR VEHICLE

Cancelling speed limiter

To cancel the speed limiter, push "CAN-

CEL" switch (2). The set indicator (5) will

disappear.

To resume the previously set speed, pull

up the "RES +/SET

-" switch (3) and

show

"SET" indicator (5).

To turn off the speed limiter system, push

"LIMIT" switch (1) and check that limit indi-

cator (4) disappears.

Also, you can turn off the speed limiter by

turning off the engine.

NOTE:

If you turn off the speed limiter system, the

previously set speed in the memory is

cleared. Set your speed again.

3-27

SUZUKI SAFETY SUPPORT

(if equipped)

Dual sensor brake support

Dual sensor brake support is a system that

detects a vehicle or a pedestrian in front of

your vehicle by the dual sensor, attempts

to avoid a collision by giving warning to the

driver, and attempts to reduce damage in

the event of a collision.

A WARNING

• Dual sensor brake support has lim-

its and may not function properly

depending on the driving condi-

tions. Do not rely excessively on

the system and always drive in a

safe manner.

For safety reasons, do not check

the operation of the system by

yourself.

Check that all passengers fasten

their seat belts when the vehicle is

being operated.

When the system is activated, there

is a risk of serious injury from

being thrown.

NOTE:

While the system is working, if a vehicle

in front of you moves outside the dual

sensor's detection field or the vehicle

can no longer be detected, the system

may stop functioning.

While the system is working, a braking

sound may be heard even if you do not

depress the brake pedal, but this is nor-

mal.

• As the function of the dual sensor brake

support is different depending on some

destinations or areas, there are type of

vehicles with the function not to detect

the pedestrians.

Frontal collision warning

When there is a risk of a frontal collision, a warning will be given through the information

display and sound.

Information display

•:::::

buzzer

78R803031

Brake assist system

When there is high probability of a frontal collision, the brake assist system provides more

powerful braking when you slam down on the brake pedal. Brake assist system might

work at the same time as automatic brake system.

Information display

78RB03032

OPERATING YOUR VEHICLE

3-28

OPERATING YOUR VEHICLE

Automatic brake system

When a frontal collision is unavoidable, the brakes will powerfully operate automatically.

(#1)

Indicator Information display

light

buzzer

78RB03033

(#1) After the vehicle has been stopped by the automatic brake system, the interior

buzzer will continue to beep until the automatic brake system is released. Also, the

indication on the information display and the dual sensor brake support indicator light

will go off 3 seconds after the automatic brake system is released.

A CAUTION

After the vehicle has been stopped by the automatic brake system, immediately

depress the brake pedal. If your vehicle is equipped with the automatic transmis-

sion, and when the automatic brake system is released, the vehicle will start to

move by the creeping function. This may result in an accident.

NOTE:

If you do not depress the clutch pedal when the vehicle has been stopped by the auto-

matic brake system, the engine will stall.

3-29

Situations where the system does not

activate

Under the following situations, the system

does not activate.

When the engine is off

When dual sensor brake support indica-

tor light and lane departure warning indi-

cator light are initially lighting

immediately after the ignition switch is

turned to "ON".

When the gearshift lever is in reverse

gear

When the ESP® system is activated

(except the frontal collision warning)

When the following switches are pushed

and the system is turned off:

- Dual sensor brake support OFF switch

- ESP® OFF switch

When the dual sensor is temporarily

stopped or malfunctioning

Situations where the system may not

activate properly

Under the following situations, the system

may not activate.

When the dual sensor cannot detect a

vehicle or a pedestrian in front of your

vehicle

Refer to "Handling dual sensor" in the

"OPERATING YOUR VEHICLE" section.

When you take evasive action with the

steering wheel or accelerator pedal

Situations where the vehicle may not

decelerate properly

Under the following situations, the vehicle

may not decelerate properly even when

the system is activated.

When the outside temperature is low, or

when the temperature of the brake is low

such as right after starting

When the brake is overheating and the

brake effect is deteriorated due to con-

tinuing to travel on a downhill road

When the brake effect is deteriorated

due to passing over puddles or washing

the vehicle

When driving on the following roads

- On sharp curves or extremely rough

surfaces

- On a steep slope

When driving on the following slippery

surfaces

- Frozen or snow-covered surfaces

- Over manholes or metal construction

plates

- Gravel

When driving in a rainy day

OPERATING YOUR VEHICLE

Situations where the system may acti-

vate by chance

Under the following situations, the dual

sensor may judge that there is a vehicle or

a pedestrian in front of you, and the sys-

tem may activate. Drive carefully and

calmly.

When passing through a toll booth with

more than recommended speeds

Before the parking lot gates or railroad

crossing gates are opened fully

When operating on hills that have vary-

ing slopes

When you suddenly accelerate and

approach the vehicle in front of you or on

neighboring lane

Front visibility is poor due to that there is

water vapor, sand or smoke or when the

vehicle in front of you or on oncoming

lane is surrounded by exhaust gas,

water or snow

When passing through masses of water

vapor or smoke

When stopping close to an obstacle in.

front of you

When passing through near a vehicle or

obstacle

3-30

OPERATING YOUR VEHICLE

54P000330

When you pass by an oncoming vehicle

on a curvy road

54?000332

When there is a roadside guard rail, or

sign on a curve

When you pass by an oncoming yehicle

that is stopped to make a right/left turn

3-31

When you pass by an oncoming vehicle

when you turn to the right/ left

When the posture of the vehicle is

changing by the road surface of the

undulation and uneven

When there is objects protruding from

the road's surface, manhole covers,

signs and other metal objects, as well as

falling objects or level changes in the

road

When there is a parking lot gates, toll

gates, railroad crossing gates or sign-

boards in the direction of travel.

When driving in the field covered with

grown grass

When the posture of the vehicle is

changing

When the mounting position of the dual

sensor is shifted by strong impact

When you pass under an object (grade

separation, road sign, billboard, street

lamp, etc.) at the top of an uphill road

When there are paint or patterns on the

road or the wall that may be indistin-

guishable from a vehicle

Frontal collision warning

There is a risk of a frontal collision and a warn-

ing will work under the following situations.

When you are operating at speeds

between approximately 15 km/h to 140

km/h (9 mph to 87 mph).(For pedestrian,

operating speed is between approxi-

mately 15 km/h to 60 km/h (9 mph to 37

mph).)

The relative speed between your vehicle

and the vehicle or pedestrian ahead is

approximately 15 km/h (9 mph) or more.

The interior buzzer will intermittently beep

and the indication on the information dis-

play will appear.

78RB03034

When the frontal collision warning sounds,

depending on the distance from the vehicle

in front of you and driving conditions, take

evasive action with the steering wheel or

brake pedal.

Brake assist system

Under the followings and there is a high

probability of a frontal collision, the brake

assist system provides more powerful

braking when you slam down on the brake

pedal.

When you are operating at speeds

between approximately 15 km/h to 80

km/h (9 mph to 50 mph).(For pedestrian,

operating speed is between approxi-

mately 15 km/h to 60 km/h (9 mph to 37

mph).)

The relative speed between your vehicle

and the vehicle or pedestrian ahead is

approximately 15 km/h (9 mph) or more.

When the brake assist system activates,

the frontal collision warning also activates

at the same time.

Automatic brake system

Under the followings and a frontal collision

is judged to be unavoidable, the brakes will

powerfully operate automatically.

When you are operating at speeds

between approximately 5 km/h to 100

km/h (3 mph to 62 mph).(For pedestrian,

operating speed is between approxi-

mately 5 km/h to 60 km/h (3 mph to 37

mph).)

The relative speed between your vehicle

and the vehicle or pedestrian ahead is

approximately 5 km/h (3 mph) or more.

When the automatic brake system is acti-

vated at a speed of approximately 50 km/h

(31 mph) or under toward the vehicle in

front of you (or toward the pedestrian,

approximately 30 km/h (19 mph) or under),

collisions may be avoidable.

While the automatic brake system is acti-

vating, the interior buzzer will continuously

beep, the dual sensor brake support indi-

cator light will blink rapidly, the indication

on the information display will appear, and

the brake lights will come on.

OPERATING YOUR VEHICLE

D

78RB03035

NOTE:

The indication on the information display

and the dual sensor brake support indica-

tor light will go off after approximately 3

seconds after the automatic brake system

is released.

3-32

OPERATING YOUR VEHICLE

Lane departure warning

When you are operating at a speed of

approximately 60 km/h (37 mph) or ov~r

and the dual sensor judges that your vehi-

cle is to deviate from the running lane, the

following warnings will work.

, The lane departure warning indicator

light will blink .

A message will appear on the informa-

tion display

The steering wheel will vibrate

Indicator

light

3-33

Information

display

78RB03036

A WARNING

• The lane departure warning may

not be suitable for every situation.

Also the system is not designed to

avoid the lane deviations automati~

cally. Do not rely excessively on

the system and always drive in a

safe manner.

Depending on road surface condi-

tions, you may n~t feel the vibra-

tion of the steering wheel even

when the lane departure warning

works.

For safety reasons, do not check

the operation of the system by

yourself.

Situations where the system does not

activate

Under the following situations, the system

does not activate.

, When dual sensor brake support indica-

tor light and lane departu_re warni~g i~di-

cator light are 1nitially lighting

immediately after the ignition switch is

turned to "ON"

When the following switches are pushed

and the system is turned off:

- Lane departure warning OFF switch

- ESP® OFF switch

When operated the hazard warning

switch

When the dual sensor is temporarily

stopped or malfunctioning

When the system judges that the inten-

tional lane change, such as during or

after fiashing the turn signal lights

Situations where the system may not

activate properly

Under the following situations, the system

may not activate.

, When you suddenly close to the partition

lines

When driving on sharp curves

When you do not return to inside of th_e

lane after the lane departure warning 1s

activated

When the electric power steering light

comes on

If the dual sensor cannot detect partition

lines except for above situations, _sys-

tem may also not activate. Refer to Situa-

tions where the dual sensor may not

activate properly" in this section for details.

Situations where the system may acti-

vate by chance

Under the following situations, the system

may activate.

• When there are a lot of lines in the run-

ning lane

When there is a shadow (for example,

the shadow of the guardrail) parallel to

the partition line

When partition line is in the shadows

When partition lines are drawn doubly

When there is a liner paint on the road of

a construction zone because the previ-

ous line has not been erased completely

When there is repair marks on the road

or a boundary between asphalt and

snow

When there is tyre marks on snow-cov-

ered or wet road

When driving in the place without parti-

tion lines (such as a tailgate or check-

point, or at an intersection, etc.)

When driving on the road diverges,

merges, etc.

When driving on an unpaved or rough

road

Vehicle swaying warning

When you are operating at a speed of

approximately 60 km/h (37 mph) or over

and the vehicle swaying warning judges

that your vehicle is unsteadiness by

detecting the meandering patterns or lane

departure warning is activate_d in a s_hort

period of time in a row following warnings

will work.

The lane departure warning indicator

light will blink

A message will appear on the informa-

tion display

The interior buzzer will intermittently

beep

~CO)

A

Indicator

Information

light

display

•

78RB03037

OPERATING YOUR VEHICLE

.A. WARNING

The vehicle swaying warning may

not be suitable for every situation.

Also, the system is not designed t?

avoid the unsteadiness of the vehi-

cle automatically. Do not rely

excessively on the system and

always drive in a safe manner.

For safety reasons, do not check

the operation of the system by

yourself.

NOTE:

Vehicle swaying warning by the meander-

ing pattern of the vehicle in the lane is

judged based on the driving data over the

past several tens of minutes, so the sys-

tem does not activate when right after

swaying.

Situations where the system does not

activate

Under the following situations, the system

does not activate.

When dual sensor brake support indica-

tor light and lane departure warning indi-

cator light are initially lighting immediately

after the ignition switch is turned to "ON".

When the following switches are pushed

and the system is turned off:

- Lane departure warning OFF switch

- ESP® OFF switch

When the dual sensor is temporarily

stopped or malfunctioning

3-34

OPERATING YOUR VEHICLE

Situations where the system may not

activate properly

Under the following situations, the system

may not activate.

• Right after lane changing

If the dual sensor cannot detect partition

lines except for above situations, the sys-

tem may also not activate. Refer to "Situa-

tions where the dual sensor may not

activate properly" in this section for details.

High beam assist

After the auto high beam switch operation,

head light is turned ON with the lighting

control lever on "Auto" position when the

ambient becomes dark, the system is acti-

vated. When the high beam assist is acti-

vated, high beam assist indicator light

(green) comes on.

Under the any of following situations, the

low beam turns on.

• When vehicle speed is approximately 35

km/h (21.7 mph) or under

When the front of the vehicle is bright

When the vehicle in front of you turned

on the lights

There are many street lamps in front of

you

Under the all of the following conditions

are met, the high beams (main beams)

turns on.

3-35

When vehicle speed is approximately 40

km/h (24.9 mph) or over

When the front of the vehicle is dark

When the vehicle in front of you is driv-

ing without lights

• There is few street lamps in front of you

A. WARNING

• High beam assist has limits and

may not function properly depend-

ing on the environ-

ment.

Always drive in a safe manner,

switch manually to the low beams

and high beams (main beams), if

necessary.

Switching of the low beams and

high beams (main beams) it might

not match the feeling of the driver.

NOTE:

Light vehicle such as a bicycle might not

detect.

When the sudden acceleration, high

beam assist might not operate for a few

seconds, even if vehicle speed exceeds

40kmlh (24.9 mph).

How to use High beam assist

78RB03009

When the ignition switch is turned to "ON",

switch the lighting control lever to "AUTO"

position and then push this lever forward.

High beam assist indicator light comes on

in green.

To cancel the function, pull the lever

toward you.

f,

52RM20740

Situations where the system does not

activate

When the high beam assist warning light

(orange) comes on by the temporary

stop or malfunction of system.

NOTE:

When the function of the dual sensor brake

support is temporarily stopped, high beam

assist will be temporarily stopped. Refer to

"Temporary stop or failure of the dual sen-

sor'' in this section for details.

When high beam assist warning light

(orange) is initially lighting immediately

after the ignition switch is turned to "ON".

Under the following situations, high

beam may not automatically switched

to low beam.

When you pass by an oncoming vehicle

on a curvy road where the visibility is

poor

When another vehicle crosses in front of

you

When the vehicle in front of you

glimpses due to continuous curves,

medial strip or street trees

When the vehicle in front of you

approaches towards you from the far

lane

When the vehicle in front of you is driv-

ing without lights

For the following cause, there is case

where the switching timing of the high

beam and low beam is varied.

When the lights of the vehicle in front of

you is dark

When only one side of the lights of the

vehicle in front of you is turned on

The directions and movements of the

vehicle in front of you

When the vehicle in front of you is a

motorcycle

When driving on the following roads

- On sharp curves or extremely rough

surfaces

- On a steep slope

When your vehicle is weighed down by

heavy items in the luggage compartment

or rear seat

OPERATING YOUR VEHICLE

Under the following situations, the

brightness of the surrounding area can

not be detected accurately, and there is

a case where the high beam is a nui-

sance to pedestrians or the vehicle

ahead, or low beam will remain to con-

tinue.

In these cases, change high beam or

low beam manually.

When lights are similar to headlights or

taillights are around

When the vehicle in front of you is driv-

ing without lights

When the headlights of oncoming vehi-

cle are covered in dirt or discolored

When the optical axis of the headlight of

oncoming vehicle is deviated

When the brightness is changed

extremely and continuously

When driving on an undulated or bumpy

road

When driving on the road with a lot of

curves

When there are things that strongly

reflect light, such as road signs or mir-

rors in front of the vehicle

When the rear part of the preceding

vehicle strongly reflects light, such as

containers

When the headlights of your car are

damaged or covered in dirt

When the vehicle is tilted due to the flat

tyres or being towed

3-36

OPERATING YOUR VEHICLE

Other than the described above, the dual

sensor cannot be detected the vehicle in

front of you or light source, and there is a

case where high beam assist may not acti-

vate properly.

Refer to "Situations where the dual sensor

may not activate properly" in this section

for details.

Under the following situations, switch

high beam or low beam manually,

When switching back and forth between

the high beams (main beams) and low

beams frequently

When there is a problem using the high

beams (main beams)

When it is considered disturbing to other

drivers or pedestrians

There is a case where high beams (main

beams) is switched to low beams by the

fog lights of the vehicle in front of you.

Street lights, traffic signals, and illumina-

tion of billboards or signs may cause the

high beams (main beams) to switch to the

low beams, or low beam to remain on.

3-37

Dual sensor brake support OFF

switch

You can turn off the dual sensor brake

support system.

In the following situations, push and hold

the dual sensor brake support OFF

switch as unexpected dangers may be

possible if ii is activated.

- When the vehicle is placed upon ates-

ter such as when undergoing a vehicle

inspection

- When the vehicle is put up on a lift,

and the tyres are idling

- When the vehicle is being towed

- When the vehicle is being carried on a

car carrier

- When the vehicle is being operated on

a race track

- When there is vinyl curtains or pendu-

lous branches in front of the vehicle

- When driving in the field covered with

grown grass

- When using an automatic car washer

- When the vehicle is placed upon a car

elevator or placed in a mechanical

parking lot

- With a spare tyre or snow chains

equipped

- When you have a temporarily repaired

flat tyre

- When you have an accident or break-

down

- When the automatic brake system is

activated frequently

- When tyres are not inflated to the rec-

ommended tyre pressure

- With worn tyres equipped

- With non-specified sized tyres or

wheels equipped

- With a modified suspension equipped

- When attaching an item which inter-

feres with the visibility of the dual sen-

sor

- When the vehicle is being weighed

down by heavy items

- When the vehicle is used to tow a

trailer

78RB03010

When you want to turn off the system,

push and hold the dual s_ensor_ brake

support OFF switch (1) until the interior

buzzer beeps and the dual sensor brake

support OFF indicator light (2) comes

on.

Perform the following method to turn the

system back on.

• Push and hold the dual sensor brake

support OFF switch (1) until the interior

buzzer beeps and the dual sensor brake

support OFF indicator light (2) goes off.

Turn off the engine and then turn it on

again.

A WARNING

If you attempt to press the dual sen-

sor brake support OFF switch while

driving, you could lose control of the

vehicle.

Do not press the dual sensor brake

support OFF switch while driving.

Lane departure warning OFF switch

You can turn off the lane departure warn-

ing and the vehicle swaying warning.

i~ (2) -

OFF

~i

(1) ii

_____ Jj

78RB03011

When you want to turn off the system,

push and hold the lane departure warn-

ing OFF switch (1) until the interior

buzzer beeps and the lane departure

warning OFF indicator light (2) comes

on.

Perform the following method to turn the

system back on.

• Push and hold the lane departure warn-

ing OFF switch (1) until the interior

buzzer beeps and the lane departure

warning OFF indicator light (2) goes off.

OPERATING YOUR VEHICLE

A WARNING

If you attempt to press the lane

departure warning OFF switch while

driving, you could lose control of the

vehicle.

Do not press the lane departure

warning OFF switch while driving.

·NOTE:

Once the system is turned off, it does not

turn on automatically, even if you turn off

the engine and then starl the engine again.

To turn the system back on, push the

switch again.

3-38

OPERATING YOUR VEHICLE

Traffic sign recognition

(if equipped)

When the vehicle with the dual sensor

passes the traffic sign, the traffic sign is

shown on the information display on the

cluster meter in order to notify the driver.

This system may not work properly outside

Europe.

60

..

A WARNING

The function of the traffic sign recog-

nition has limits and may not func-

tion properly depending on the

driving conditions of circumstances.

Do not rely excessively on this func-

tion and always drive in a safe man~

ner.

3-39

NOTE:

The traffic sign may be shown with delay

on the information display depending on

the circumstances and conditions of the

vehicle

The number of the traffic sign for this

function shows up to three signs on the

information display

The traffic signs are disappeared on the

information display under the following

situations

- When the vehicle was run in constant

distance after showing the traffic signs

on the information display (except for

regulation end sign},

- When a period of time passed after

the traffic signs on the information dis-

play (only for regulation end sign),

- When turning right or left with the turn

signal lights blinked,

- For manual transmission vehicle, the

gearshift lever is in "R" position, for

automatic transmission vehicle, the

gearshift lever is in "P" or "R" position

(except for speed limit sign).

To change the traffic sign recognition

setting, select "Sign recog." in "Setting

mode" on the information display. Then,

select "ON" or "OFF"

When the ignition switch was turned

"OFF" with the speed limit sign shown on

the information display and then the igni-

tion switch is fumed "ON" again, the

information display shows the same

speed limit sign the last time the ignition

switch was fumed "OFF"

When you drive in the area where unit of

velocity is changed, the traffic signs may

not be appeared or the different traffic

signs may be appeared on the informa-

tion display after passing the actual traf-

fic signs. This is not a malfunction. The

display will be resumed after driving for a

while.

The speed limit sign on the information

display that is higher or lower than the

actual limited speed sign may be dis-

played for the speed limit sign

Situations where the system does not

activate

Under the following situations, the system

does not activate.

When the engine is off

When dual sensor brake support indica-

tor light and lane departure warning indi-

cator light are initially lighting

immediately after the ignition switch is in

"ON" position

For manual transmission vehicle, the

gearshift lever is in "R" position, for auto-

matic transmission vehicle, the gearshift

lever is in "P", "R", or "N" position

When the dual sensor is temporarily

stopped or malfunctioning

When the ESP® OFF switch is pushed

and the system is turned off

When the traffic sign recognition is

turned off by operating the setting mode

of information display

When parking brake is applied

When you drive in the area that there are

no speed limit signs and has speed limit

OPERATING YOUR VEHICLE

3-40

OPERATING YOUR VEHICLE

Types of recognized traffic signs

Information

Type of the traffic sign

message

[l[I

Speed limit begins/ends

No overtaking begins/ends

Speed limit with supplemental mark

(Displayed simultaneously with speed

limit)

Supplemental mark exists

I

(Display example)

All canceled (All restrictions canceled. Returns to default road regu-

lation.)

NOTE:

The above traffic signs are representative examples. The traffic signs may be different

in every country.

3-41

Situations where the dual sensor may

not activate properly

There may be high possibility not to detect

the traffic signs by the dual sensor under

the following situations. Also the function

of the dual sensor may be stopped tempo-

rarily. When the situations are improved,

the temporary stop of the function will be

canceled.

When there is bad weather such as

heavy rain, fog or a blizzard

When the dual sensor is hit by a bright

light such as sunlight or the headlight of

oncoming vehicle

When there is a sight of similar tone and

color such as a snowscape

When the vehicle runs on the road which

became bright by the reflected light,

When there are no lights or lamps as

street lamps, etc around in the dark

Front visibility is poor due to that there is

water vapor, sand or smoke or when the

vehicle in front of you is surrounded by

exhaust gas, water or snow

When you drive in the dawn, the dusk

and the night or when you drive in a dark

place as an indoor parking lot

When the vehicle direction to go ahead

or the vehicle position was largely

changed (for example, the lane change,

left turn, or right turn),

When the windshield is covered in fog,

snow, ice or dirt

81M40380

When raindrop, water or dirt on the wind-

shield is not wiped up enough

While using the windshield washer

When a wiper blade other than SUZUKI

genuine parts, including short type wiper

blade is used

When the tyres are not inflated to the

recommended tyre inflation pressure or

when the tyres except the assignment

size are equipped,

72M20405

When your vehicle is weighed down by

heavy items in the luggage compartment

or rear seat

When the headlights are covered in dirt,

snow, ice or mud

When the optical axis of the headlight is

deviated

When the brightness changes extremely

(for example, passing the entrance or

exit of tunnel),

When the vehicle is swaying on the

rough roads (for example, unevenness

roads or stone pavement roads) and the

visibility of the monocular camera is

unstable,

There may be a case to display the traf-

fic sign irrelevant to the vehicle, the traf-

fic sign that is not existed around the

vehicle under the following situations.

- When the traffic sign is existed on the

branched road, the junction or the

adjacent lane near the road that the

vehicle is moving,

- When there are similar things to the

color and the object of the traffic sign

(for example, the similar traffic sign,

the signboard or the structures)

- When the vehicle that the decal or

sticker like the traffic sign is pasted on

is existed in front of your vehicle, or

when you overtake such a vehicle,

- When the traffic sign is in front of the

vehicle on the roundabout,

OPERATING YOUR VEHICLE

NOTE:

The traffic sign may be continued to dis-

play on the information display under the

following situations. Drive safely accord-

ing to the actual traffic rules.

- When you drive in the area where the

different speed limit is established

even though there is no speed limit

sign,

- When you drive in the area where the

end of traffic regulation is indicated by

the lane on the road even though

there is no traffic sign to indicate the

end of the traffic regulation,

Situations where the dual sensor can-

not be detected accurately by the posi-

tions or conditions of the traffic signs

The detection of traffic sign may be done

with delay or there may be a possibility to

occur no detection or inaccurate detection

of the traffic sign including the supplemen-

tal mark under the following situations.

When the traffic sign is dirt and hidden

by the leaves of the tree or the vehicle in

front of your vehicle and then it is hard to

recognize the traffic sign,

When the circumstance of the traffic sign

is complicated and it is hard to recognize

the traffic sign,

When the traffic sign is far from the vehi-

cle,

When the traffic sign is bended or

deformed,

When the color of the traffic sign is

faded,

3-42

OPERATING YOUR VEHICLE

When the direction of traffic sign is Handling dual sensor

changed,

• When the traffic sign is damaged,

• When the traffic sign is aimed diagonally

to the vehicle,

When the signboard, the poster or traffic

information signboard is installed on the

top or bottom of it,

When the object as mud, snow or the ice

is attached on the traffic sign,

• When there is a traffic sign on a corner

or a curve,

When there is a traffic sign where light of

the headlight is hard to reach,

When the traffic sign is hard to recognize

due to the illumination on the roads or

the shadow of the building,

When the size of the traffic sign is small, (1) Dual sensor

When the traffic sign is a lighting type,

When the traffic sign is assimilated into

the building on the background and it is

hard to recognize the traffic sign,

When there is a hidden or rubbed part

on the traffic sign and the traffic sign is

hard to recognize,

When the traffic sign is refiected by the

strong light (for example, backlight or

headlight) and the dual sensor cannot

detect accurately,

NOTE:

There may be a possibility to detect the

supplemental mark inaccurately or not to

detect it as the traffic sign by the situations

around the vehicle.

3-43

78RB03012

A WARNING

The detection performance of the

dual sensor has limits and the dual

sensor cannot detect all vehicles,

pedestrian, object of the high beam

assist (such as the lights of the vehi-

cle in front of you, street lamps, etc.),

partition lines or traffic sign. Do not

rely excessively on the system and

always drive in a safe manner.

• Observe the following instructions

in order to keep the dual sensor

functioning properly. If mishandled,

the dual sensor cannot accurately

detect a vehicle, a pedestrian, an

object of the high beam assist

(such as the lights of the vehicle in

front of you, street lamps, etc.) or

partition lines in front of you, the

system will not function properly

and unexpected accidents may

occur.

- Do not touch the lens of the dual

sensor.

- Do not clean the lens of the dual

sensor by yourself.

- Do not strike the body of, or any

surrounding parts of the dual

sensor.

(Continued)

A WARNING

(Continued)

- Do not remove or disassemble

the dual sensor.

- Do not stick or affix anything to

the lens of the dual sensor, not

even clear items.

• When the windshield around the

dual sensor is deformed or dam-

aged, or the windshield in front of

the dual sensor is cracked because

of an accident, the dual sensor can-

not detect an obstacle in front of

you, a pedestrian, an object of the

high beam assist (such as the

lights of the vehicle in front of you,

street lamps, etc.), partition lines or

traffic signs properly. If driving with

these damaged parts, the dual sen-

sor brake support will not function

properly and unexpected accidents

may occur. Operate the dual sensor

brake support OFF switch to turn

off the dual sensor brake support,

and ask a SUZUKI dealer to have

them inspected.

(Continued)

A WARNING

(Continued)

Do not apply any accessories

(other than SUZUKI genuine acces-

sories), films or stickers to the area

listed below. These may affect with

visibility of the dual sensor. If the

area of the dual sensor is

obstructed, the dual sensor cannot

detect any vehicles, pedestrians,

objects of the high beam assist

(such as the lights of the vehicle in

front of you, street lamps, etc.),

partition lines or traffic signs prop-

erly and the dual sensor brake sup-

port may not function properly.

Also, if applying them to an area

other than the prohibited area, it

may affect with the function of the

dual sensor by reflection of light or

an image. In this case, move them

to another place.

- On windshield

OPERATING YOUR VEHICLE

A WARNING

Do not remove or disassemble

laser sensor parts of dual sensor.

Do not look into irradiation portion

of dual sensor by using the optical

instrument such as magnifying

glass, the objective glass, etc at

distance within 10 cm (3.9 inch)

from dual sensor when the ignition

switch is turned to "ON". Your eyes

might be damaged by laser.

3-44

OPERATING YOUR VEHICLE

Laser explanatory label

Max overage power: 45 mW

Pulse duration: 33 ns

Wavelength: 905 nm

IEC 60825-1 :2007

Complies with FDA performance standards for laser products

except for deviations pursuant to Laser Notice No. 50, dated

Ju!y 26'", 2001

52RM30510

Laser emission data

Maximum average power: 45 mW

Pulse duration: 33 ns

Wave length: 905 nm

Divergence

(horizontal x vertical): 28' x 12'

NOTE:

The detection of the vehicle and an obsta-

cle in front of you, partition lines ·on the

road by the dual sensor is limited within the

visual range. It also takes several seconds

to detect and activate the alert after an

object is appeared in the visual range of

the dual sensor.

3-45

Laser classification label

INVISIBLE LASER RADIATION

DO NOT VIEW DIRECTLY WITH

OPTICAL INSTRUMENTS (MAGNIFIERS)

CLASS 1M LASER PRODUCT

52RM30520

A WARNING

Do not stick a sticker or a film

(including transparent thing) on the

front of dual sensor of the outside

windshield as shown in the below

illustration.

78RB03013

(1) (2) Prohibited area

The prohibited area (1) and (2) are shown

as below.

(1) From top edge of windshield to dual

sensor approximately 10 cm (3.9

inch) below of the bottom end of dual

sensor

(2) Approximately 20 cm (7.8 inch) from

the center of dual sensor to right and

left approximately 10 cm (3.9 inch)

A WARNING

Do not stick a sticker or a film

(including transparent thing) below

the dual sensor camera inside the

windshield shown as following illus-

tration.

When there is a large temperature gap

between inside of the vehicle and outside

air (such as winter), windshield is easy to

fog. If the front portion of dual sensor on

the windshield is fogged up or covered

with condensation or ice, dual sensor

brake support may not activate temporar-

ily. In this case, use the front defroster to

remove the fog, etc.

When cleaning inside of the windshield, do

not adhere the glass cleaner to lens.

OPERATING YOUR VEHICLE

3-46

OPERATING YOUR VEHICLE

Temporary stop or failure of the dual sensor

The following chart shows the temporary stop or failure of the dual sensor.

(1)

(2)

(3)

(4)

3-47

ra

!~

I ,.

I

®

...

FUNCTION

TEMPORARILY

DISABLED

(#1)

.~

SYSTEM

WARNING

Dual sensor

Temporary

Stop

On

Off

On

Failure

Off

On

(1) Dual sensor brake support indicator

light

(2) Lane departure warning indicator light

(3) High beam assist warning light

(orange)

(4) Indication of information display

#1: Depending on the cause of the tem-

porary stop or failure, the following

message may appear simultaneously.

.~

FUNCTION

TEMPORARILY

DISABLED

(CAM VIS)

.~

FUNCTION

TEMPORARILY

DISABLED

(CAM TEMP)

75RM350

NOTE:

When the function of the dual sensor is

temporarily stopped or malfunctioning, all

of following functions will be turned off.

Dual sensor brake support

Lane departure warning

Vehicle swaying warning

High beam assist

Traffic sign recognition

Temporary stop of the dual sensor

Under the following situations, the function

of the dual sensor stops temporarily.

When the situations are improved, the

temporary stop of the function will be can-

celed.

When the visibility of the dual sensor is

poor

Refer to "Situations where the dual sen-

sor may not activate properly" in this

section for details.

When the temperature of the body of

dual sensor is high

When the systems related to the dual

sensor brake support are stopped tem-

porarily

When the battery has a voltage abnor-

mality

Failure of the dual sensor

When the dual sensor is faulty, the function

of the dual sensor is stopped until the igni-

tion switch is turned to "LOCK".

Find a safe place to park and turn the igni-

tion switch to "LOCK".

Restart the engine, and check that the dual

sensor brake support indicator light, lane

departure warning indicator light, and high

beam assist warning light go off.

If all of the indicators stay on after

restarting the engine, there may be a

failure of the dual sensor. Ask a SUZUKI

dealer to have the dual sensor

inspected.

NOTE:

Under the following situations, the dual

sensor brake support indicator light, lane

departure warning indicator light, and

high beam assist warning light come on

after the engine has been started, it

does not indicate a malfunction. Once

the ignition switch to is turned to "LOCK"

position and then the engine is restarted,

these indicators will go off.

- When the automatic brake system has

been operating 3 times

- When the automatic brake system has

been operating for long periods

OPERATING YOUR VEHICLE

The function of the dual sensor is

stopped if the dual sensor brake support

indicator light, lane departure warning

indicator light, and high beam assist

warning light come on and there may be

a failure of the dual sensor, but it r}oes

not hinder normal driving.

Pedestrian detection

The dual sensor detects pedestrians by

whose size, shape or motion.

•

T

(1)

75RM238

(1) About 1 - 2 m (3.3 - 6.6 ft)

3-48

OPERATING YOUR VEHICLE

A WARNING

Even when the detection conditions

are satisfied, not all pedestrians may

be detected by the dual sensor.

In the following situations, there may

be a high possibility of undetectable

or delay of detection. Always drive in

a safe manner.

• A person who walks in a group

• A person who walks beside a wall

or another obstacle

A person who has an umbrella up

A person whose color is similar to

the background and who is

blended into the scenery

• A person who has a big luggage

• A person who walks with a stoop or

who crouches.

• A person who is lying down

• A person who is in a dark place

• A person who jumps out in front of

you

• A person at night

NOTE:

As the function of the dual sensor brake

support is different depending on some

destinations or areas, there are type of

vehicles with the function not to detect the

pedestrians.

3-49

Situations where the dual sensor may

not activate properly

In the following situations, there may be a

high possibility that the dual sensor cannot

detect a vehicle, a pedestrian, an object of

the high beam assist (such as the lights of

the vehicle in front of you and street lamps,

etc.), partition lines or traffic sign. Also the

function of the dual sensor may be

stopped temporarily. When the situations

are improved, the temporary stop of the

function will be canceled.

81M40380

When there is bad weather such as

heavy rain, fog or a blizzard

When the dual sensor is hit by a bright

light such as sunlight or the headlight of

oncoming vehicle

When there is a sight of similar tone and

color such as a snowscape

When there is a dark place and no land-

mark around

When front visibility is poor due to that

there is water vapor, sand or smoke or

when the vehicle in front of you is sur-

rounded by exhaust gas, water or snow

• When your vehicle gets close to an

object in a dark place such as at dusk, at

dawn or an indoor parking lot

When the windshield is covered in fog,

snow, ice or dirt

• When raindrop, water or dirt on the wind-

shield is not wiped up enough

While using the windshield washer

When a wiper blade other than SUZUKI

genuine parts, including short type wiper

blade is used

When lens of dual sensor is dirty or dam-

aged

72M20423

When the vision of the dual sensor is

obstructed with the followings:

- A sticker or film on the windshield

- An accessory on the windshield

- A crack or scratch of the windshield

- A long object such as a roof carrier or

ski board on the roof

72M20405

When your vehicle is weighed down by

heavy items in the luggage compartment

or rear seat

When wheel alignment is deviated

When the tyres are not infiated to the

recommended tyre pressure or the tyres

are worn

With snow chains or non-specified sized

tyres equipped

When you have a temporarily repaired

fiat tyre

With a modified suspension equipped

When passing through the entrance or

exit of the tunnel and the brightness is

changed extremely

When driving without lighting the head-

lights at night or in tunnels

When driving on the following roads

- On sharp curves or extremely rough

surfaces

- On a steep slope

- On seam of the road

When vehicle is swaying

When the optical axis of the headlight is

deviated

With modified headlights and/or front fog

lights equipped

When the headlights are covered in dirt,

snow, ice or mud

When the following types of a vehicle are

in front of you, or when the following situa-

tions occur, the dual sensor may not detect

a vehicle in front of you or may need more

time to detect a vehicle. ·

72M20407

Vehicles in front of you have small, low,

or uneven backs as shown below:

- A track without side or back gates, and

when mounting no luggage on the

cargo bed

- A vehicle with luggage protruding out

from the back

- A specially shaped vehicle such as a

car carrier trailer or a motorcycle with

side car

- A low-slung vehicle

When ground clearance of vehicle in

front of you is extremely high.

When a vehicle is oncoming or retreating

vehicle

OPERATING YOUR VEHICLE

When a vehicle facing sideways

When a vehicle in front of you without

turning on the tail lights at night or in tun-

nels

When a vehicle in front of you refiects

sunlight strongly

When there is a wall in front of the

parked vehicle

When there is another obstacle beside a

vehicle

D

72M20406

When only a part of the vehicle in front of

you is within the dual sensor detection

field

When the difference of speed between

the vehicle in front of you and your vehi-

cle is increased

When the distance to the vehicle in front

of you is short

When the vehicle in front of you is diffi-

cult to refiect the laser beam

When driving on a curve

For a while after escaping from a curve

When the vehicle in front of you turns,

accelerates or decelerates suddenly

When a vehicle in front of you jumps out

3-50

OPERATING YOUR VEHICLE

• When you change the lane and

approach the leading vehicle

When the following types of partition lines

are in front of you, or when the following

situations occur, the dual sensor may not

detect the lines or may need more time to

detect the lines.

• The narrow lane width

• When the lane is difficult to detect

- No partition lines, or faded lines

- The color of partition lines is similar to

the road

- The width of partition lines is narrow

- The partition lines has blurred

- There are road studs or stones

- The partition lines can not be seen, or

difficult to see due to sand, etc.

- Driving on a road that is wet due to

rain, after the rain, puddles, etc.

- The partition lines drew on a curb

- Driving on a road that is bright due to

reflected light, etc.

When the distance to the vehicle in front

of you is short

Immediately after the lane change, or

immediately after passing through the

intersection.

3-51

OPERATING YOUR VEHICLE -> SUZUKI SAFETY SUPPORT (if equipped) for Your Suzuki Jimny SUV Fourth Generation (2018-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals