2018-2026 Suzuki Jimny SUV OPERATING YOUR VEHICLE -> Tyre pressure monitoring system (TPMS) (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

OPERATING YOUR VEHICLE -> Tyre pressure monitoring system (TPMS) (if equipped) for Your Suzuki Jimny SUV Fourth Generation (2018-2026)

OPERATING YOUR VEHICLE
For vehicles with instrument cluster
(Type A)
For vehicles with instrument cluster
(Type B)
78RB03045
3-63
NOTE:
• When the ESffe OFF switch is pushed
again, the hill hold control system is acti-
vated again.
When the hill hold control system is
deactivated and the transfer lever is
shifted from "4L" position to "4H" posi-
tion, the hill hold control system is acti-
vated again.
When the hill hold control system is
deactivated, hill descent control system
is also deactivated.
Tyre pressure monitoring
system (TPMS) (if equipped)
The tyre pressure monitoring system is
designed to alert you when one or more of
the tyres on your vehicle is significantly
under-inflated. The tyre pressure monitor-
ing system (TPMS) senso_r containing a
unique identification code 1s mounted on
each wheel. The TPMS sensors transmit
tyre pressure signals to the receiver of the
tyre pressure monitoring system controller.
When the inflation pressure of one or more
tyres indicates significant under-inflation,
the low tyre pressure warning light shown
below comes on.
NOTE:
The word "telltale" in this section, means
an indicator.
Low tyre pressure warning light
(!)
52D305
Each tyre should be checked monthly
when cold and infiated to the infiation pres-
sure recommended by the vehicle manu-
facturer on the vehicle placard or tyre
pressure label. (If your vehicle has tyres of
a different size than the size indicated on
the vehicle placard or tyre pressure label,
you should determine the proper tyre pres-
sure for those tyres.)
As an added fuel efficiency feature, your
vehicle has been equipped with a tyre
pressure monitoring system (TPMS) that
illuminates a low tyre pressure telltale
when one or more of your tyres is signifi-
cantly under-infiated.
Accordingly, when the low tyre pressure
telltale illuminates, you should stop and
check your tyres as soon as possible, and
infiate them to the proper pressure.
Driving on a significantly under-infiated
tyre causes the tyre to overheat and can
lead to tyre failure. Under-infiation also
reduces fuel efficiency and tyre tread life,
and may affect the vehicle's handling and
stopping ability.
Please note that the TPMS is not a substi-
tute for proper tyre maintenance, and it is
the driver's responsibility to maintain cor-
rect tyre pressure, even if under-infiation
has not reached the level to trigger illumi-
nation of the TPMS low tyre pressure tell-
tale.
A WARNING
Relying only on the tyre pressure
monitoring system to determine
when it is necessary to add air to the
tyres can result in loss of control or
an accident.
Check tyre pressures monthly when
the tyres are cold. If necessary,
adjust them to the recommended
inflation pressure as specified on the
vehicle's tyre information placard
and in this owner's manual. Refer to
"Tyres" in "INSPECTION AND MAIN-
TENANCE" section.
OPERATING YOUR VEHICLE
A WARNING
Failure to take corrective action when
the low tyre pressure warning light is
not working or when it comes on and
blinks while driving can lead to an
accident.
If the low tyre pressure warning light
does not come on for 2 seconds after
the ignition switch is turned to "ON"
position, or comes on and blinks
while driving, have your vehicle
inspected by a SUZUKI dealer. Even if
the light turns off after blinking, indi-
cating that the monitoring system
has recovered, you should still have
the system checked by a SUZUKI
dealer.
3-64
OPERATING YOUR VEHICLE
A WARNING
The load-carrying capacity of your
tyres is reduced at lower inflation
pressures. If your tyres are even
moderately under-inflated, the load
on the tyres may exceed the load-car-
rying capacity of the tyres, which
could lead to tyre failure. The low tyre
pressure warning light will not alert
you to this condition, because it only
comes on when one or more of your
tyres becomes significantly under-
inflated.
Check and adjust your tyre pressure
at least once a month. Refer to
"Tyres" in "INSPECTION AND MAIN-
TENANCE" section.
3-65
A WARNING
Continuing to drive with the low tyre
pressure warning light on can lead to
an accident, resulting in severe injury
or death.
If the low tyre pressure warning light
comes on and stays on, reduce your
speed and avoid abrupt steering and
braking. Be aware that driving on a
significantly under-inflated tyre can
cause the tyre to overheat and can
lead to tyre failure, and may affect
steering control and brake effective-
ness. Stop in a safe place as soon as
possible and check your tyres.
If you have a flat tyre, replace it
with the spare tyre (if equipped).
Refer to "Jacking instructions" in
"EMERGENCY SERVICE" section
for the tyre replacement method.
Also refer to "Replacing tyres and/
or wheels" for instructions on how
to restore normal operation of the
TPMS after you have had a flat tyre.
• If one or more of your tyres is
under-inflated, adjust the inflation
pressure in all of your tyres to the
recommended inflation pressure as
soon as possible.
The low tyre pressure warning light can
come on due to normal causes such as
natural air leakage and pressure changes
caused by changes in temperature or
atmospheric pressure. Adjusting the air
pressure in the tyres to the pressure
shown on the tyre information placard
should cause the low tyre pressure warn-
ing light to turn off.
To make the low tyre pressure warning
light go off, adjust the tyre pressures when
the tyres are cold, and drive the vehicle for
about 10 minutes.
When the adjusted tyre pressure is recog-
nized, the low tyre pressure warning light
will go off and the information display
shows the current tyre pressure (if you
select the TPMS monitor (if equipped)).
NOTICE
If the low tyre pressure warning light
does not go off even when you drive
for more than 10 minutes after adjust-
ing the cold tyre pressure, there may
be a problem with the TPMS. Have
your vehicle inspected by a SUZUKI
dealer.
If the light turns on again shortly after
adjusting the pressure in your tyres. you
may have a flat tyre. If you have a flat tyre,
replace it with the spare tyre (if equipped).
Refer to "Jacking instructions" in "EMER-
GENCY SERVICE"" section. Refer to
"Replacing tyres and/or wheels" for instruc-
tions on how to restore normal operation of
the tyre pressure monitoring system after
you have had a flat tyre.
61MM0A198
NOTE:
For a certain type of instrument cluster
only, the information display shows the
above warning and indicator message
when this light comes on.
When the tyre pressure is adjusted in
high altitude areas, the low tyre pressure
light may not turn off even after tyre
pressure adjustment. In this case, adjust
the inflation pressure to a slightly higher
pressure than the one shown on the tyre
informaUon placard.
The low tyre pressure warning light may
turn off temporarily after coming on. This
could be due to increase of surface tem-
perature after long distance driving or
traveling to a high temperature area.
Even if the tyre pressure warning light
turns off after coming on, check the infla-
tion pressure of all tyres.
OPERATING YOUR VEHICLE
To reduce the chance that the low tyre
pressure warning light will come on due
to normal changes in temperature and
atmospheric pressure, it is important to
check and adjust the tyre pressures
when the tyres are cold. If you check
tyres after driving, they are warm. Even
if the tyre pressure seems to be good in
this condition, it could fall below the
specified pressure when tyres cool
down. Also, if tyres are inflated to the
specified pressure in a warm garage, the
tyre pressure could fall below the speci-
fied one when you drive the vehicle out-
side in very cold temperature. If you
adjust the tyre pressure in a garage that
is warmer than the outside temperature,
you should add 1 kPa to the recom-
mended cold tyre pressure for every
O.B'C difference between garage tem-
perature and outside temperature.
3-66
OPERATING YOUR VEHICLE
TPMS malfunction indicator
Your vehicle has also been equipped with
a TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is com-
bined with the low tyre pressure telltale.
When the system detects a malfunction,
the telltale will flash for about 75 seconds
and then remain continuously illuminated.
This sequence will continue upon subse-
quent vehicle start-ups as long as the mal-
function exists.
The TPMS malfunction indicator is not
reset even after the engine is turned off; it
remains in the ON state until the normal
conditions are restored.
When the malfunction indicator is illumi-
nated, the system may not be able to
detect or signal low tyre pressure as
intended. TPMS malfunctions may occur
for a variety of reasons, including the
installation of replacement or alternate
tyres or wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction tell-
tale after replacing one or more tyres or
wheels on your vehicle to ensure the
replacement or alternation of tyres and
wheels to allow the TPMS to continue to
function properly.
3-67
NOTICE
The tyre pressure sensors can be
damaged if you do not take proper
precautions.
We highly recommend that you
have tyres repaired or replaced by
a SUZUKI dealer. The tyre pressure
sensors can be damaged by instal-
lation or removal of tyres.
• Do not use liquid sealants for a flat
tyre unless your vehicle is
equipped with a flat tyre repair kit
instead of a spare tyre.
NOTICE
If the low tyre pressure warning light
comes on frequently, there may be
something wrong with one or more of
the tyres, tyre pressure sensors or
the monitoring system.
If the low tyre pressure warning light
comes on frequently, have your vehi~
cle inspected by a SUZUKI dealer.
61MM0A199
NOTE:
For a cerlain type of instrument cluster
only, the information display shows the
above warning and indicator message
when this light comes on.
TPMS limitations
The tyre pressure monitoring system may
not function properly under certain circum-
stances. In the following situations, the low
tyre pressure warning light may come on
and remain on or may blink.
When you replace a flat tyre with the
spare tyre.
When you include a spare tyre during a
tyre rotation.
When the TPMS sensor is damaged
during a tyre replacement or liquid seal-
ants are used to repair a flat tyre.
When the electronic signal of TPMS sen-
sor is disturbed in one of the following
ways:
- Electric devices or facilities using simi-
lar radio wave frequencies are nearby.
- A metallic film that may cause radio
wave interference is attached on the
window.
- A lot of snow or ice covers the vehicle,
in particular, around the wheels or
wheel housings.
- Snow tyres that are not installed with
genuine TPMS sensors or snow
chains are used.
When you use non-genuine SUZUKI
wheels or tyres.
When the pressure of any tyre is too
high.
When there is a problem with the
receiver of the TPMS controller.
TPMS setting (For instrument clus-
ter - Type A)
You can set one of the initial value of
tyre pressure below that is indicated on
the tyre information label.
- Comfort Mode
- Load Mode
For details on how to set the mode, refer to
"Setting mode" in "BEFORE DRIVING"
section.
A WARNING
If the loading weight has changed,
adjust the tyre pressure according to
the tyre information label and set the
initial value via the information dis-
play. If the loading weight, tyre pres-
sure and initial value do not match,
the tyre pressure monitoring system
will not function properly.
OPERATING YOUR VEHICLE
TPMS setting (For instrument clus-
ter• Type B)
• You can check the current tyre pressure
on the information display.
• You can set one of the initial value of
tyre pressure below that is indicated on
the tyre information label.
- Comfort Mode
- Load Mode
A WARNING
If the loading weight has changed,
adjust the tyre pressure according to
the tyre information label and set the
initial value via the information dis-
play. If the loading weight, tyre pres-
sure and initial value do not nJatch,
the tyre pressure monitoring system
will not function properly.
3-68
OPERATING YOUR VEHICLE
To check the current tyre pressure
(1)
78RB03016
1) When the ignition switch is turned to
"ON" and the vehicle is stationary, push
and hold the indicator selector knob (1)
on the instrument cluster for a while to
change the information display to the
setting mode.
Setting mode
78RB03017
3-69
2) Turn the indicator selector knob (1) left
or right to select "TPMS" and push the
indicator selector knob.
NOTE:
If you exit the setting mode, select "Back"
and push the indicator selector knob (1 ).
TPMS
78RB03018
3) Turn the indicator selector knob (1) left
or right to select "Tyre Press" and push
the indicator selector knob.
78RB03019
4) The display shows current tyre pres-
sure.
NOTE:
If the low tyre pressure warning light
comes on, the information display will be
switched to "Tyre Press" display and the
corresponding tyre pressure indication
blinks to alert you which tyre(s) is(are)
low pressure.
The display may not show the tyre pres-
sure for about 10 minutes after the vehi-
cle begins to move. This is because the
TPMS system learns the tyre pressure
within this 10 minutes. The display will
show the tyre pressure after 10 minutes
pass.
If you stop the vehicle and turn the igni-
tion switch to "LOCK" position, and leave
it for 20 minutes or more, tyre pressure
wi/1 be reset and will be indicated as 0
kPa when the engine is restarted. In this
case, the current tyre pressure indication
will recover after driving for a while.
However, if any of tyre pressures has
been detected as low pressure before
stopping the engine, the tyre pressure
indication may not recover and may be
indicated as "---".
To set the initial value of tyre pressure
(1)
78RB03016
1) When the ignition switch is in "ON"
position and the vehicle is stationary,
.
push and hold the indicator selector
knob (1) on the instrument cluster for a
while to change the information display
to the setting mode.
OPERATING YOUR VEHICLE
78RB03017
2) Turn the indicator selector knob (1) left
or right to select "TPMS" and push the
indicator selector knob.
NOTE:
If you exit the setting mode, select "Back"
and push the indicator selector knob (1 ).
3-70
OPERATING YOUR VEHICLE
78RB03018
3) Turn the indicator selector knob (1) left
or right to select "TPMS Mode" and
push the indicator selector knob.
78R803020
3-71
4) Turn the indicator selector knob (1) left
or right to select the initial value and
push the indicator selector knob.
78RB03021
5) When the display shows the message
shown in the above illustration, the set-
ting is completed.
Replacing tyres and/or wheels
If you got a fiat tyre and replaced it with the
spare tyre, SUZUKI recommends that you
have a SUZUKI dealer mount a new tyre
on the wheel that had the fiat tyre. The
TPMS is already set up to recognize the ID
code of the original wheel, and normal
TPMS operation will be restored.
If you need to replace any wheels on your
vehicle, a SUZUKI dealer must check that
TPMS sensors are installed in the new
wheels and must set up the TPMS to rec-
ognize the new sensors.
NOTE:
A TPMS sensor is not installed in the spare
tyre. You should use the spare tyre only in
an emergency situation, and should
replace the spare tyre as soon as possible
to restore normal TPMS operation.
A WARNING
Use of tyres or wheels not recom-
mended by SUZUKI can result in fail-
ure of the TPMS.
When replacing tyres and wheels,
use only tyres and wheels recom-
mended by SUZUKI as standard or
optional equipment for your vehicle.
Refer to "tyres" in "INSPECTION AND
MAINTENANCE" section for addi-
tional information.

Related Topics

Popular Owner Manuals