2024-2026 Cupra Terramar SUV Parking and manoeuvring User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Parking and manoeuvring for Your Cupra Terramar SUV First Generation (2024-2026)

Parking and manoeuvring
225
Park the vehicle
Parking and manoeu-
vring
Park the vehicle
Parking
When parking your vehicle, all legal require-
ments should be observed.
1. Connect the electronic parking brake
›››
page226.
2. Automatic transmission: switch on the
parking lock by pressing button P.
3. Stop the engine and turn o the ignition.
Turn the steering wheel slightly to engage
the steering lock.
4. On slopes, turn the steering wheel so that
if the parked vehicle were to start moving, it
would steer toward the kerb.
5. Exit the vehicle ››› . Watch out for other
road users!
6. Take all vehicle keys with you and lock it.
To avoid damage or hazardous situations, al-
ways park the vehicle on a suitable parking sur-
face ››› .
Rear seat warning
The function depends on the vehicle's equip-
ment.
When the ignition is switched o, a text mes-
sage in the infotainment system reminds you
not to leave any passengers in the rear seats
››› .
If a rear door was used before the trip, a text
message is also displayed on the instrument
cluster and an audible warning may sound. This
warning can be activated/deactivated in the
infotainment system menu Settings > Screen
settings > Rear seat warning.
WARNING
If the vehicle is parked incorrectly, it could
roll away, even on gentle slopes. This can
cause accidents and serious injuries.
●
When parking, always carry out the opera-
tions in the stipulated order.
●
Before leaving the vehicle, make sure that
the electronic parking brake is engaged.
WARNING
If children, people who may need assistance
or animals are left unattended in the vehicle,
accidents and serious injuries can occur.
●
Never leave children, people who may need
assistance or animals unattended in the ve-
hicle. They could operate the gear selector
and release the electronic parking brake. The
vehicle could be set in motion.
●
Never leave children, people who may need
assistance, or animals in the vehicle. De-
pending on the season, very high or low tem-
peratures can be reached inside a closed ve-
hicle.
●
Always take all vehicle keys with you when
leaving the vehicle.
NOTICE
The presence of irregularities on the ground,
sand or mud can cause damage to the vehicle
and mean that it cannot be parked properly.
●
Always park the vehicle on rm and at
ground.
226
Parking and manoeuvring
NOTICE
Components on the underside of the vehicle,
such as bumpers, spoilers and running gear
components, can be damaged when running
over objects protruding from the ground.
●
Drive carefully when entering buildings, on
ramps, driving over kerbs or xed markings,
and on descents.
NOTICE
Avoid parking the vehicle where the hot ex-
haust system could ignite inammable mate-
rials, such as dry grass, low bushes, spilt fuel
or ammable materials.
Electronic parking brake
Using the electronic parking brake
Fig.148 Centre console, lower part:
electronic parking brake button.
Connecting
The electronic parking brake can be activated
whenever the vehicle is at a standstill, even
when the ignition is switched o. Activate it
whenever you leave or park the vehicle.
●
Pull and holdthe button ›››Fig.148.
The parking brake is on when the red indicator
lamp on the instrument cluster and the but-
ton indicator lamp turns on.
●
Release the button.
Switching o
●
Switch the ignition on.
●
Press the button ›››Fig.148. At the same
time step hard on the brake pedal or, if the
engine is running, press the accelerator pedal
slightly.
●
The indicator lamp on button and thered in-
dicator lamp on the instrument cluster turn
o.
Automatic disconnection when moving o
The electronic parking brake automatically dis-
connects when moving o in any of the follow-
ing situations, if the driver's door is closed and
the driver's seatbelt is buckled:
●
Vehicles with an automatic gearbox: A gear
range is engaged or switched to another one
and the accelerator pedal is lightly pressed.
●
To facilitate certain manoeuvres, there are
exceptions that allow the parking brake to
disconnect automatically without the driver's
seatbelt being buckled.
The parking brake can be prevented from
being automatically released by continuously
pulling up the switch when moving o.
The electronic parking brake is not disconnec-
ted until the
button is released. This can fa-
cilitate starting o when a heavy load is towed
›››page322.
Parking and manoeuvring
227
Electronic parking brake
Automatic application when exiting the ve-
hicle incorrectly
In vehicles with automatic transmission, the
electronic parking brake may be applied auto-
matically if the system detects an improper at-
tempt to exit the vehicle. For example:
●
no seat presence detection,
●
seat belt unfastened,
●
door open.
The electronic parking brake also holds the ve-
hicle in the neutral N position.
WARNING
If the vehicle is left incorrectly, it could roll
away. This could lead to accidents, serious
injury and property damage.
●
When parking the vehicle, always perform
the appropriate operations in the indicated
order ›››page225, Parking.
●
Before leaving the vehicle, make sure that
the electronic parking brake is applied and
that the control lamp next to the gear se-
lector is red on the instrument cluster.
Protection against unintentional movement
If you do not want the electronic parking brake
to be applied automatically, e.g. in a car wash
or if you want to push or tow the vehicle, the
vehicle’s ability to roll can be maintained .
Deactivate:
With the vehicle stationary, press down the
brake pedal and select the N position on the
gear selector.
●
Conrm the message Deactivate roll-away
protection in the infotainment system.
●
OR: open the vehicle settings in the infotain-
ment system > Vehicle > Brakes > Deacti-
vate the “Roll-away protection function”.
Activate:
●
Press the button ›››Fig.148. The elec-
tronic parking brake is activated.
NOTICE
The vehicle may be able to roll even when the
ignition is switched o.
Automatic connection when the ignition is
turned o
This function can be deactivated through the
Infotainment system.
Emergency brake function
Only use the emergency brake function in an
emergency, if the vehicle cannot be stopped
by pressing the brake pedal ›››
!
●
Pull and holdthe button. The vehicle
will brake sharply. At the same time, an audio
warning will be heard.
●
To stop the braking process, release the but-
ton or press the accelerator.
When the ESC Sport or ESC OFF mode is se-
lected, ESC will reactivate to assist the driver
during braking. Depending on the model ver-
sion, the ESC will either switch back to its previ-
ous disconnected state or will remain on.
WARNING
Improper use of the electronic parking brake
can cause accidents and serious injury.
●
Never use the electronic parking brake to
stop the vehicle, unless it is an emergency.
The braking distance is considerably longer.
Always use the brake pedal.
●
Never accelerate from the engine when a
gear range or a gear is engaged and the en-
gine is running. The vehicle could start mov-
ing even when the electronic parking brake is
engaged.
NOTICE
To prevent the vehicle from unintentionally
moving when parking it, rst apply the elec-
tronic parking brake and then remove your
foot from the brake pedal.
Troubleshooting
There is a defect in the electronic park-
ing brake
The control lamp lights up in yellow.
228
Parking and manoeuvring
Visit a CUPRA dealer or other specialist work-
shop.
The electronic parking brake does not re-
lease.
The 12-volt battery is discharged.
●
Use the jump start ›››page340.
The electronic parking brake makes noises
●
When the electronic parking brake is applied
and released, noises may be heard.
●
The system performs automatic and audi-
ble checks sporadically in the parked vehicle
if some time elapses without the electronic
parking brake being used.
AutoHold function
Fig.149 In the lower part of the centre
console: AutoHold function button.
The Auto Hold function holds the vehicle at a
standstill and prevents it from moving without
it being necessary to keep the brake pedal de-
pressed.
When the Auto Hold function is
switched on, the lamp on the instru-
ment cluster lights up grey.
When the Auto Hold function is active,
the control lamp on the instrument
cluster lights up green.
The control lamp of the
button ›››Fig.149
remains on when the Auto Hold function is
connected.
Requirements
●
If the system has detected the driver’s pres-
ence based on various signals such as: seat-
belt, driver’s door, driver’s seat occupied and
others.
●
The engine is running.
Connecting and disconnecting
Press the Auto Hold button ››› . The control
lamp on the button turns on when the Auto
Hold function is switched on. The function is
now available to be activated. The lamp on the
button goes out when the Auto Hold function
is switched o.
Switching on and o automatically
If the Auto Hold function was switched on with
the Auto Hold button before switching o the
ignition, the function will remain on after the
ignition is re-engaged.
If the Auto Hold function was not switched
on, it will remain o next time the ignition is
switched on.
The Auto Hold function is automatically turned
o if the following conditions are met:
1. If any of the requirements of the function
are no longer met.
2. If the engine runs erratically or has any
anomaly.
3. Automatic gearbox: If any of the tyres have
only minimal contact with the ground, e.g.,
if the axles are crossed.
The Auto Hold function is temporarily switched
o while the user pulls the electronic parking
brake button .
Activation and deactivation
The Auto Hold function activates automatically
if the following conditions are met (all points
must be met at the same time):
1. The function is switched on
2. The vehicle is brought to a complete
standstill with the brake pedal on a at sur-
face or on a slope.
3. The engine rotates “correctly”.
230
Parking and manoeuvring
Deactivating
●
The automatic brake operation function de-
activates when a park assist system is switched
o.
●
OR: to temporarily deactivate the manoeu-
vre braking function, press the function
button on the park assist screen and change
the setting.
WARNING
Never allow the automatic braking opera-
tions of park assist systems to lead you to
take any risk that compromises safety. In cer-
tain situations, the automatic braking inter-
vention may only work in a limited way or
not work at all. Collisions with obstacles can
injure people and damage the vehicle. The
system is not a replacement for driver aware-
ness.
●
Pay attention and do not rely solely on park
assist systems.
●
Always be prepared to brake and control
the steering yourself.
●
Do not take any risks that compromise
safety.
●
Act in accordance with the warnings and
driving recommendations of the parking sys-
tems.
Note
●
Switch o the parking system if the auto-
matic brakes operate excessively, e.g. when
driving o-road.
●
After the park assist’s manoeuvre braking
function has braked the vehicle, it deacti-
vates for the next 5 metres of movement
in the same direction, and becomes active
again after changing gear or changing the
position of the gear selector.
Troubleshooting
The parking system behaves dierently than
expected
There can be several causes:
●
The system requirements are not met.
●
The sensors or the camera are dirty or have
ice on them ›››
page395.
●
The camera lens is not clean and the camera
image is not clear ›››page395.
●
Some noise sources, such as a jackhammer
or a cobblestone surface can interfere with the
ultrasound signal.
●
The vehicle has some type of damage in the
sensor or camera area, e.g. due to a parking
impact.
●
The sensor detection zone or eld of view of
the camera are blocked by an accessory, e.g. a
bike rack.
●
Changes have been made to the paintwork
or structural modications in the sensor or
camera area, e.g. at the front of the vehicle or
to the running gear.
Also take into account the messages displayed
on the infotainment system display.
Sensor or camera without visibility, or the
parking system has been switched o
If a sensor fails, that sensor zone is perma-
nently switched o. The aected sensor zone
may be displayed on the infotainment system
with a symbol and a greyed-out graphic
segment. If necessary, the parking system
switches o the aected zone.
If the park assist is not working properly, a
continuous audible signal sounds for a few
seconds when it is switched on. If applicable,
a message to this eect is displayed on the
instrument cluster display
●
Check if one of the causes indicated above
has occurred.
●
Once the source of the problem has been
eliminated, the system may be reconnected.
●
If the problem persists, consult a specialised
workshop.
Parking and manoeuvring
231
Park Distance Control Plus (Park Pilot)
A
B
C
D
Park Distance Control
Plus (Park Pilot)
Description
Fig.150 Parking aid view on the
Infotainment system display.
Parking aid plus assists the driver by giving
visual and audio warnings about obstacles de-
tected in front of and behind the vehicle.
The bumpers are tted with sensors. When
an obstacle is detected, it is indicated by au-
dible signals and in the Infotainment system
›››
Fig.150.
When moving close to an obstacle, it is possi-
ble to know if the obstacle is in front of the
vehicle or behind it according to the sound
frequency.
The approximate measurement range of the
sensors is:
1.20 m
0.90 m
1.60 m
0.90 m
As you approach the obstacle, the frequency
of the audible signals will increase. The signal
will sound continuously at around 0.30 m: Stop
the vehicle!
If the separation is maintained, the warning
volume is reduced after about 2.5 seconds.
Error messages
If a an error or fault message is displayed on
the instrument cluster in Park Assist, there is a
fault.
If the fault doesn't disappear before discon-
necting the ignition, it will not be indicated
next time the parking aid is connected.
If a rear sensor is faulty, only the obstacles in
the front area are detected. If a front sensor is
faulty, only the obstacles in the rear area are
displayed. The symbol is displayed.
We recommend taking the vehicle to a special-
ised workshop to have the fault repaired.
Trailer mode
On vehicles with a factory-mounted trailer
hook, when the trailer is connected, the rear
sensors will not activate when reverse gear is
engaged or button is pressed in the Infotain-
ment system ( > Assistants). Therefore, any
objects behind or to the side of the vehicle will
not be indicated on the screen and no audio
signals will sound.
The screen will only display objects detected
at the front, and the vehicle's trajectory will be
hidden.
Parking assist settings
The indications and audible signals are set in
the Infotainment system: function button >
Assistants > Parking > > Settings.
●
Automatic activation: On/o
●
Front volume: Volume in the front and rear
area.
●
Rear volume: Volume in the rear area.
●
Reduce volume: When the parking aid is
switched on, the volume of the audio source
will be reduced, depending on the selected
option.
232
Parking and manoeuvring
WARNING
●
Always pay attention, by looking directly,
to traic and the area around the vehicle.
Assistance systems are not a replacement for
driver awareness. Responsibility always lies
with the driver.
●
The sensors have blind spots in which ob-
stacles and people are not detected. Pay spe-
cial attention to children and animals.
●
Always keep visual control of the surround-
ings: use the mirrors for additional help.
NOTICE
Park assist plus functions can be aected by
various factors which may cause damage:
●
Under certain circumstances, the system
does not detect or display certain objects:
–
Chains, trailer draw bars, bars, fences,
posts and thin trees.
–
Objects that are located above the sen-
sors, such as protrusions in a wall.
–
Objects with certain surfaces or struc-
tures, such as wire mesh fences or powder
snow.
●
Certain surfaces of objects and garments
do not reect the ultrasound sensors' signals.
The system cannot detect these objects or
people wearing such clothes correctly.
●
Sensor signals may be aected by external
sound sources. This may prevent them from
detecting people or objects.
●
If the system warns you of the proximity of
a low obstacle, please note that after being
detected by the system, the obstacle in ques-
tion may disappear from the measurement
sensors as the vehicle moves closer, and the
system will no longer warn of its presence. In
certain circumstances, objects such as high
kerbs that could damage the underside of
the vehicle are not detected.
●
If the parking distance warning system is
ignored, the vehicle could suer considera-
ble damage.
●
Damage to the radiator grille, bumper,
wheel arch and vehicle underbody can mod-
ify the orientation of the sensors. This can
aect the parking aid function.
Have the function checked by a specialised
workshop.
●
A number plate or number plate holder
with dimensions that exceed the space for
the number plate, or a cured or deformed
number plate can cause false detections or a
loss of visibility for the sensors.
Note
●
The display on the Infotainment system
screen shows a slight time delay.
●
In certain situations, the system can give a
warning even though there is no obstacle in
the detected area:
–
Rough or cobbled surfaces or surfaces
with long grass.
–
External ultrasound sources, such as
other vehicles equipped with ultrasound
systems.
–
Heavy rain or snow, hail or dense exhaust
gases.
–
If the number plate is not properly se-
cured to the surface of the bumper.
–
Gradient changes.
●
In order to guarantee good operation, keep
the sensors clean, free of snow and ice, and
do not cover them with stickers or other ob-
jects.
●
If you use high-pressure or vapour equip-
ment for cleaning, do not apply it directly,
unless you do so very briey, and always keep
a distance of more than 10 cm away.
●
Fitting certain accessories to the front of
the vehicle, such as a plate holder with ad-
vertising, may interfere with the operation of
the Park Assist.
●
We recommend that you practice parking
in an area without traic.
Parking and manoeuvring
233
Park Distance Control Plus (Park Pilot)
1)
The RVC button will only be displayed when reverse gear is engaged.
●
The volume and tone of the signals and
indications can be changed.
●
Please observe information on towing a
trailer.
Operating Park Assist Plus
Switching on and o manually
●
Press button in the infotainment system
( > Assistants > Parking assist > Parking
aid).
Automatic activation
●
Select reverse gear.
●
OR: if you drive forward at a speed of less
than 15 km/h (9 mph) and you encounter an
obstacle, it is detected when it is optically ap-
prox. less than 95 cm. away, or acoustically ap-
prox. 50 cm. away. If the automatic connection
is activated, a reduced display is shown.
●
OR: if the vehicle moves back a certain dis-
tance (between approx. 10 and 20 cm approx
depending on whether or not an obstacle is
detected).
When the Plus Parking Aid connects auto-
matically, a diagram of the vehicle and the seg-
ments will appear on screen. This function will
be available unless the user has deactivated it.
It only operates every time the speed drops
below 15 km/h (9 mph) for the rst time.
Automatic activation of park assist can be
switched on and o in the infotainment sys-
tem:
●
Switch the ignition on.
●
In the infotainment system select > Assis-
tants > Parking > Parking aid.
●
Check the Automatic activation box.
If activated automatically, an audible sound
warning will only be given when obstacles in
front are at a distance of less than 50 cm. ap-
prox.
If it is switched o using the button in the
infotainment system, one of the following ac-
tions must be taken for it to reactivate auto-
matically:
●
Switch o the ignition and switch it on again.
●
EITHER: drive forward at over approx.
15km/h (9mph).
●
OR: activate or deactivate the parking lock
button P.
●
OR: switch the automatic activation on and
o in the Infotainment system.
Automatic disconnection
●
Drive forward at 15 km/h (9mph) or faster.
●
OR: press the parking lock button P.
Temporary mute
●
Press the function button on the infotain-
ment screen.
●
OR: activate the electronic parking brake.
Change from reduced view to full view
●
Engage the reverse gear if your vehicle is
equipped with a reversing camera.
●
Press the car icon on the reduced view
●
OR: if the vehicle moves back a certain dis-
tance (between approx. 10 and 20 cm approx
depending on whether or not an obstacle is
detected).
Switch to the reverse assist image (Rear View
Camera “RVC”)
●
Select reverse gear.
●
OR: press the RVC button on the Infotain-
ment System display.
1)
A short conrmation signal will be heard and
the button symbol will light up when the sys-
tem is switched on.
NOTICE
Park assist plus only connects automatically
when driving very slowly. If driving style is not
adapted to the circumstances, an accident
and serious injury or damage may be caused.
234
Parking and manoeuvring
Visual indication segments
Fig.151 Park Assist view on the
Infotainment system display.
The optical indication of the segments works
as follows:
●
Grey segments: the obstacle is more than
approx. 30 cm away from the path or in the
direction opposite to travel. They are also dis-
played when the electronic parking brake is ac-
tivated.
●
Yellow segments: the obstacles lie on the
vehicle’s path and are at a distance of less than
approx. 30 cm away.
●
Red segments: obstacles are less than ap-
prox. 30 cm away.
A guiding track will indicate the anticipated for-
ward or backward trajectory, depending on the
gear that is engaged.
If an obstacle is located in the vehicle’s way,
the corresponding audible warning will sound.
When the penultimate segment is displayed,
the vehicle has reached the collision zone. In
the collision zone, obstacles are shown in red
(including those outside the trajectory). Stop
the vehicle! ››› in Description on page232
In the event the car is equipped with the Top
View Camera system, Park Assist visual guid-
ance will appear in accordance with the view
selected in the Top View Camera system.
Rear park assist
Description
Rear park assist is a visual and audible assistant
that warns of obstacles located behind the ve-
hicle.
There are sensors integrated in the rear
bumper. When they detect an obstacle, you
are alerted by audible and visible warnings on
the Infotainment system.
If the Top View Camera system is installed, the
rear park assist will issue an audible warning
about objects near the rear of the vehicle, and
the Top View Camera image will be available on
the infotainment screen, giving a real image of
the objects around the car.
Particularly make sure that the sensors are not
covered by adhesives, residues, dirt and the
like, as this could aect the system's operation.
Cleaning instructions ›››
page395.
The approximate measurement range of the
rear sensors is:
●
Side area: 0.60 m
●
Central area: 1.60 m
As you approach the obstacle, the frequency
of the audible signals will increase. The signal
will sound continuously at around 0.30 m: Stop
the vehicle! ››› on page232.
If the separation is maintained, the warning
volume is reduced after about 2.5 seconds.
Turning on Park assist
●
Select reverse gear.
Turning o Park assist
●
Drive forward at 15 km/h (9mph) or faster.
●
EITHER: use the selector lever to select N or
D, or press the parking lock button P.
Park assist settings
The indications and audible signals are set in
the Infotainment system: function button >
Assistants > Parking > > Settings.
●
Rear volume: Volume in the rear area.
●
Reduce volume: When Park Assist is
switched on, the volume of the audio source
will be reduced, depending on the selected
option.
Parking and manoeuvring
235
Intelligent Park Assist (IPA) automatic parking system
Error messages
If a an error or fault message appears on the
instrument cluster in Park assist, there is a fault.
If the fault doesn't disappear before switching
o the ignition, it will not be indicated next
time the park assist is connected.
We recommend taking the vehicle to a special-
ised workshop to have the fault repaired.
Towing device
In vehicles factory tted with a towing device,
when the trailer is connected, the park assist
will not be activated when reverse gear is en-
gaged.
WARNING
Observe the safety warnings ››› in De-
scription on page232.
Intelligent Park Assist
(IPA) automatic parking
system
Introduction
The automatic parking system is an additional
function of ParkPilot ›››
page231 and helps
the driver nd a suitable parking space from
among the following types:
●
reverse parking in suitable perpendicular
and parallel spaces,
●
park driving forwards in suitable perpendicu-
lar spaces,
●
exit a parking space driving forwards from a
parallel space,
●
park in a suitable space driving forwards at
an angle to partially enter the selected parking
space. The system will centre the vehicle in the
parking space,
●
nish reverse parking into a space in which
you have attempted to park manually by parti-
ally entering with the rear of the vehicle.
In vehicles with an automatic parking system
and factory infotainment system, the front,
rear and side areas are represented, and the
position of obstacles is shown relative to the
vehicle.
The automatic parking system is subject to
certain limitations inherent to the system
and its use requires special attention by the
driver››› .
WARNING
The technology used in the automatic park-
ing system has a series of limitations inherent
to the system itself and the use of ultrasonic
sensors. The use of Park Assist should never
tempt you to take any risk that may compro-
mise safety. The system is not a replacement
for driver awareness.
●
Any accidental movement of the vehicle
could result in serious injury.
●
Adapt your speed and driving style at all
times to suit visibility, weather, road and traf-
c conditions.
●
Certain surfaces of objects and garments
do not reect the ultrasound sensors' sig-
nals. The system cannot detect, at least cor-
rectly, these objects or people wearing such
clothes.
●
Ultrasound sensor signals may be aected
by external sound sources. In certain circum-
stances this may prevent them from detect-
ing people or objects.
●
The ultrasound sensors may have blind
spots in which obstacles and people are not
detected.
●
Monitor the area around the vehicle at all
times, since the ultrasound sensors do not
detect small children, animals or certain ob-
jects in all situations.
WARNING
Quick turns of the steering wheel when park-
ing or exiting a parking space with the au-
tomatic parking system can cause serious in-
jury.
●
Do not hold the steering wheel during ma-
noeuvres to park or exit a parking space un-
til the system requests it. Doing so disables
the system during the manoeuvre, resulting
in the parking being cancelled.
236
Parking and manoeuvring
NOTICE
●
In certain circumstances, the ultrasonic
sensors do not detect objects such as trailer
hitches, bars, fences, posts or thin trees, or
an open (or opening) rear lid, which could
damage the vehicle.
●
Retrotting of certain accessories to the
vehicle, such as a bicycle rack, may interfere
with the operation of the automatic parking
system and cause damage.
●
The automatic parking system uses as a
reference parked vehicles, kerbs and other
objects. Make sure that the tyres and wheels
are not damaged while parking. If necessary,
interrupt the parking manoeuvre on time to
avoid damaging the vehicle.
●
The ultrasound sensors on the bumper may
be damaged or shifted in the event of a colli-
sion, for example, when entering or exiting a
parking space.
●
If you use high-pressure or steam equip-
ment to clean the ultrasound sensors, do not
apply it directly unless very briey and always
from a distance of more than 10 cm.
●
A registration plate or plate holder on the
front that is larger than the space for the reg-
istration plate, or a registration plate that is
curved or warped can cause:
–
False detections.
–
The sensors to lose visibility.
–
Cancellation of the parking manoeuvre
or defective parking.
●
If one of the ultrasonic sensors is damaged,
the area corresponding to that group of sen-
sors (front or rear) is deactivated and can-
not be activated until the fault is corrected.
However, you can still use the sensors of the
other bumper as per usual. If there is a fault
in the system, consult a specialist workshop.
CUPRA recommends going to a specialised
CUPRA dealer or any SEAT dealership for this
purpose.
Note
●
In order to guarantee good system oper-
ation, keep the ultrasound sensors of the
bumper clean, free of snow or ice, and do not
cover them with stickers or other objects.
●
Certain sources of noise, such as rough as-
phalt or paving stones and the noise of other
vehicles can induce the automatic parking
system or ParkPilot to give erroneous warn-
ings. The presence of metal objects can also
aect the manoeuvre.
●
To become familiar with the system and
its functions, CUPRA recommends that you
practice operating the automatic parking
system in an area where there is not too
much traic or in a car park.
Description of the automatic park-
ing system
The components of the automatic parking
system are the ultrasonic sensors located in
the front and rear bumpers, the
button to
switch the system on and o and the messages
on the infotainment system display.
Prerequisites for parking
●
The traction control (TCS) must be switched
on ›››page191.
●
Speed when passing next to the parking
space: do not exceed approx. 50km/h
(31mph).
●
Keep a distance between 0.5and2.0metres
when driving past the parking space.
●
Space length (parallel parking): vehicle
length +1meter.
●
Space width (parking bay): vehicle width
+1.1meters.
Requirements for leaving the parking space
(only for parallel parking)
●
The traction control (TCS) must be switched
on ›››page191.
●
Space length: length of the vehicle
+0.5metres.
Parking and manoeuvring
237
Intelligent Park Assist (IPA) automatic parking system
Prematurely stopping or automatically inter-
rupting the manoeuvres for parking or exit-
ing a parking space
The automatic parking system interrupts the
manoeuvres for parking or exiting a parking
space in any of the following cases:
●
Press button in the infotainment system,
> Assistants > Parking > Automatic park-
ing system.
●
The driver takes control of the steering
wheel.
●
The parking manoeuvre can involve up to 8
movements.
●
The parking manoeuvre does not end within
6 minutes after activation of the automatic
steering.
●
There is a fault in the system (the system is
temporarily unavailable).
●
TCS is switched o.
●
TCS or ESC intervene with regulation.
●
A door or the luggage compartment is
opened.
●
The parking system encounters an unexpec-
ted obstacle.
●
The parking system detects high rolling re-
sistance, e.g. if there is an obstacle on the
ground (stone, bump, kerb, etc.).
Special characteristics
The automatic parking system is subject to
certain limitations inherent to the system. For
example, it is therefore not possible to use it to
enter or exit a parking space on sharp bends or
on very steep hills.
After changing a wheel
If, after changing a wheel, the vehicle stops
entering and exiting parking spaces correctly,
the circumference of the new wheel may be
dierent and the system may need to adapt
to it. The adaptation is automatic and takes
place during driving ››› in Introduction on
page235.
Selecting a parking type
Fig.152 On the infotainment system
display: parking modes indication.
Automatic parking includes the following 5
types of parking:
Reverse parallel parking.
Reverse angle parking.
Forward angle parking.
Reverse parallel parking without driving
past rst: “Help me”.
Forward or reverse parking in a parking bay
without driving past rst.
238
Parking and manoeuvring
Selecting a parking type after passing in
front of the space
After activating the automatic parking system
and after detecting a parking space, the info-
tainment system display proposes a type of
parking. The automatic parking system selects
the parking type automatically. The selected
type is shown on the infotainment system dis-
play ›››Fig.152.
●
The prerequisites for parking with the
automatic parking system must be met
›››page236.
●
Press the button in the infotainment sys-
tem, > Assistants.
●
When the system is switched on, the symbol
on the infotainment system display is high-
lighted. The selected type of parking is also
displayed. You can change the type of parking
on the infotainment system display.
●
If there are more spaces available, another
space can be selected by clicking on it on the
infotainment system display.
●
Follow the instructions displayed on the info-
tainment system display while paying attention
to traic and drive the vehicle past the parking
space.
Reverse parallel parking without driving past
rst (type
)
With this type of parking , press button
so that the system completes the parking that
has already been started. The system will only
switch on if suicient progress has been made
with the manoeuvre (the side sensor must be
able to detect the reference vehicle). If it is
impossible to successfully complete the ma-
noeuvre that has been started, the system it-
self will drive out of the parking space before
starting parking in a similar way to type
.
Special case of forward or reverse parking
into a parking bay without driving past
rst.
●
The prerequisites for parking with the
automatic parking system must be met
›››page236.
●
Move forward towards the parking space
while paying attention to traic and stop the
vehicle with the front part partially inside the
parking space.
●
Press the button once in the infotainment
system, > Assistants.
●
When the system is switched on, the symbol
on the infotainment system display is high-
lighted. The selected parking mode without a
reduced view is also displayed.
●
Let go of the steering wheel ››› in Intro-
duction on page235.
Parking with the automatic parking
system
The prerequisites have to be met to park with
the automatic parking system ›››
page236
and the parking mode has to be selected
›››page237.
Parking
Fig.153 On the infotainment system display:
parallel parking position.
Fig.154 On the infotainment system display:
parking bay parking position.
Parking and manoeuvring
239
Intelligent Park Assist (IPA) automatic parking system
1
2
3
4
›››
Fig.153, ›››Fig.154
Your vehicle
Parking space detected
Indication showing the proposed parking
manoeuvre
Start parking manoeuvre
●
Look at the display on the infotainment sys-
tem's screen to see if the space has been de-
tected as “appropriate” and if the correct posi-
tion for parking has been reached ›››Fig.153,
›››Fig.154. Stop the vehicle and follow the in-
structions shown on the infotainment screen.
●
Stop the vehicle, press the brake and, after a
short pause, press the Start
4
button in the
infotainment system.
●
Let go of the steering wheel ››› in Intro-
duction on page235.
●
Please note the following message:
Parking the vehicle... Steering intervention
active
●
The automatic parking system will park au-
tonomously by taking control of the steering
wheel (transverse control of the vehicle) and
control of the accelerator and brake pedals
(longitudinal control of the vehicle).
●
Once the manoeuvres have been comple-
ted, this is indicated by an audio and visual
warning in the infotainment system. At this
point the vehicle will be parked and immobi-
lised (gear P activated) and will turn o.
Progress bars
Fig.155 On the infotainment system display:
progress bar
The progress bar
5
on the infotainment sys-
tem display shows the relative distance to be
covered as a symbol. The more complete the
progress bar, the shorter the distance to com-
plete the parking manoeuvre.
Fig.156 On the Infotainment System
display: parking space
Note
If the parking space is displayed with arrows
on its sides, this indicates that it is possi-
ble to park in a dierent way in the same
space by pressing on the highlighted space
›››Fig.156.
Note
If the manoeuvre is terminated prematurely
during parking, the result may not be the
best.
Leaving a parking space with the
automatic parking system (only for
parallel parking)
Fig.157 On the infotainment system
display: leaving a parallel parking space.
1
Your vehicle
2
Message giving the proposed manoeuvre
to exit the parking space
240
Parking and manoeuvring
Leaving a parking space (parallel parking)
The necessary conditions to exit a park-
ing space with Park Assist have to be met
›››page236.
●
Press the in the infotainment system:
> Assistants. When the system is switched on,
the symbol on the infotainment system dis-
play is highlighted.
●
Turn on the corresponding turn signal to-
wards the road you will enter when exiting the
parking space, and press the brake pedal.
●
Tap the Start button
3
in the Infotainment
system.
●
Let go of the steering wheel ››› in Intro-
duction on page235. Please note the follow-
ing message:
Vehicle driving out of the parking space...
Intervention in active steering.
●
The automatic parking system will automati-
cally perform the manoeuvres for getting the
vehicle out of the parking space by taking con-
trol of the steering wheel (transverse control
of the vehicle) and control of the accelerator
and brake pedals (longitudinal control of the
vehicle).
●
The vehicle can be driven out of the park-
ing space when a message to this eect is
displayed in the infotainment system (Vehicle
out of the parking space. Take control of
the vehicle) and, if necessary, an audio sig-
nal sounds. Take control of the steering wheel
while maintaining the steering angle set by the
automatic parking system.
●
Paying attention to the traic and surround-
ings, exit the parking space.
Automatic Parking System
Plus with memory func-
tion
Introduction
The Automatic Parking System Plus with mem-
ory function oers assistance when parking in
frequently used parking spaces. The vehicle
automatically manoeuvres along a previously
saved route to the parking space.
The availability of the Automatic Parking Sys-
tem Plus with memory function depends on
the vehicle’s equipment.
How it works
The Automatic Parking System Plus with mem-
ory function is an extension of the Automatic
Parking System.
This parking system uses the front camera to
detect the surrounding area and saves the
route to the parking space, with a maximum
distance of 50m. Once the parking process
is saved in the Assistant, the vehicle is able to
reach the parking space automatically.
The driver must monitor the area around the
vehicle at all times ›››
.
Automatic braking may occur if there are ob-
stacles in the vehicle’s path or if a dangerous
situation arises.
Prerequisites
●
GPS coordinates of the vehicle's position are
available.
●
Suicient space for manoeuvring. The vehi-
cle may have to travel a few meters to reach
the programmed parking route.
WARNING
The smart technology used in parking sys-
tems cannot ignore the laws of physics and
only works within the limits of the system.
Failure to take this into account may result
in accidents and serious injuries, as well as
damage to the vehicle.
●
Pay attention to the parking process and
the traic around you. Look in the direction
that the vehicle is parking.
●
Do not use the Automatic Parking System
Plus with memory function in parking spaces
where there are no dened boundaries, e.g.
near the edge of lakes or rivers or near un-
fenced slopes.
Parking and manoeuvring
241
Automatic Parking System Plus with memory function
WARNING
The driver is responsible for automatic park-
ing at all times. There is a risk of accidents.
●
Only park the vehicle if you have a valid
driver’s license.
●
Follow the traic regulations of the country
you are in.
●
Do not leave the driver’s seat at any point
during the parking manoeuvre.
●
If necessary, operate the turn signals your-
self.
●
Use the brake pedal to slow down or even
stop the vehicle in dangerous situations.
WARNING
The system is only capable of a limited re-
sponse to sudden changes in external condi-
tions. Collisions with other road users may
occur.
●
Do not use the parking system when traic
speeds are in excess of 50 km/h (30 mph).
●
Always keep a safety distance of at least
one vehicle length at junctions.
●
Do not perform automatic parking from
the other side of the road or across several
lanes.
WARNING
The vehicle may occupy/invade the path of
oncoming traic.
●
Pay attention to the parking process and
the traic around you.
●
Keep the vehicle under control and use the
brake if necessary.
WARNING
The parking process cannot be carried out
correctly if the roadway is slippery; the vehi-
cle may skid. This can cause accidents and
damage to the vehicle.
●
Do not use the Park Assist in winter road
conditions.
Saving the parking process
Find a suitable parking space
●
The parking space is clearly visible and un-
obstructed. Underground car parks and multi-
storey car parks are not suitable.
●
There is good visibility, i.e. no heavy rain, fog
or darkness.
Programming of the parking process may be
limited if the parking space is unsuitable.
Program the process for reaching a parking
space
1. Drive to the parking space as normal.
2. Stop the vehicle safely.
3. Save the parking process as a parking
space in the infotainment system.
Follow the indications below to get the best
possible result when parking.
●
Carry out the parking process as slowly as
possible.
●
Avoid adjusting the trajectory of the vehi-
cle during the last few meters to the parking
space.
●
Do not turn the steering wheel to its end
stop, move it too quickly or change direction
many times while driving.
Saving a parking space
Once you have reached the desired parking
space, you can save it in the following ways:
Variant 1: saving a parking space in the Park
Assist with memory function menu
1. Press the button in the infotainment
system; or: > Assistants > Park Assist
with memory function.
2. Click on the icon
.
3. Press the + icon.
4. Select the function button, assign the sym-
bol you want (›››Fig.158
1
) and conrm
it.
242
Parking and manoeuvring
You have saved a new parking space in the
menu. The system stores the route with a
maximum distance of 50m.
Variant 2: saving a parking space in the depar-
ture menu
1. Press the icon Save parking manoeu-
vre.
The parking process is saved as a parking
space with GPS coordinates. The system
stores the route with a maximum distance
of 50m.
Note
To replace the GPS coordinates with a name
for the parking space, edit the space in the
vehicle’s parking system.
Reprogramming the parking process of a
saved parking space
If you want to reprogram a parking process,
e.g. to improve the nal result or to reach
the parking space from another location, you
must rst delete the parking space saved in the
menu.
1. Delete that parking space stored in the In-
fotainment system.
2. Reprogram the parking process in its en-
tirety.
Note
When deleting a stored parking space, the
entry and exit processes for that parking
space are always deleted.
Parking and manoeuvring
243
Automatic Parking System Plus with memory function
View and edit parking spaces
Fig.158 Schematic representation: Park Assist
menu with memory function.
1
Saved parking spaces.
2
Add the last parking process
3
Edit saved parking spaces.
4
Start the parking process.
Open the menu
All parking processes are displayed as favour-
ites in the menu of the automatic parking sys-
tem with memory function.
1. In the infotainment system, tap
; or
> Parking assistants > Park Assist with
memory function
Edit or delete parking spaces
1. Press
3
.
You can edit any of the saved parking
spaces.
2. To rename a parking space or assign a dif-
ferent symbol to it, press icon
for that
parking space.
Or: to delete a parking space, press on the
icon for that space.
To delete all parking spaces, press of all
parking spaces.
Saved parking space status
Fig.159 Infotainment system: parking
spaces without navigation.
1
Parking space not available.
2
Parking space available.
3
Automatic parking process selected.
244
Parking and manoeuvring
Fig.160 Infotainment system: parking
space with guided route for the navigation
system (depending on country and vehicle
equipment).
Driving to and from a parking
space
When approaching a saved parking space, the
System oers a parking process on the Info-
tainment system display.
●
Stop the vehicle as close as possible to the
stored route, a maximum of one metre away.
●
Always approach the initial position of the
parking process from the same direction.
Note
Impediments may occur if visibility is very
poor, e.g. in the dark, when parking and exit-
ing a parking space.
Variant 1: Start from the Automatic parking
system with memory function menu
1. Stop the vehicle near the parking space
and hold it stationary with the brake pedal.
2. If necessary, click on the parking space
available icon in the Parking System menu
›››
Fig.158
1
. The function button will be
displayed in copper.
3. Press the Start button ›››
Fig.158
4
.
4. Let go of the steering wheel and take your
foot o the brake pedal.
The system will start the parking process.
5. Always wait for the Parking system to n-
ish turning the steering wheel at the end
of the parking process for optimal results
›››
.
At the end of the parking process, an audi-
ble signal will sound and a message to this
eect will be displayed on the infotainment
system.
The electronic parking brake will be ap-
plied.
6. Park the vehicle.
Variant 2: Start from Navigation in the info-
tainment system
Once you reach the destination, a message will
be displayed on the infotainment system.
1. Stop the vehicle and hold it stationary with
the brake pedal.
2. Press the Start button in the message.
3. Let go of the steering wheel and take your
foot o the brake pedal.
4. Observe the images in the infotainment
system.
The system will start the parking process.
5. Follow the instructions for variant 1 from
step 5 onwards.
WARNING
Sudden steering wheel movements can
cause serious injury.
●
Do not grab the steering wheel during the
manoeuvre, unless the system asks you to do
so.
●
If a dangerous situation arises, grab the
steering wheel.
Navigate to a parking space as a
destination
Which parking spaces can be used as navi-
gation destinations?
Saved parking spaces with a navigation symbol
›››
Fig.160 can be transferred to the naviga-
tion system as destinations. This function de-
pends on the country and vehicle equipment.
Parking and manoeuvring
245
Automatic parking system plus with remote function (My CUPRA App)
Start the guided route
1. To select a destination, press on a button
with a navigation symbol in the parking
system menu.
2. Conrm the message in the infotainment
system.
The guided route to that destination will
begin and the Parking System menu will
close.
Or: follow the directions to exit a parking
space with the parking system.
3. Once the vehicle has arrived at the desti-
nation, read the message on the infotain-
ment system.
The parking system with memory function
is ready to automatically park the vehicle.
Automatic parking system
plus with remote function
(My CUPRA App)
Introduction
The driver can control the parking process
from outside the vehicle via a mobile app.
How it works
The automatic parking system with remote
parking function is an extension of the auto-
matic parking system.
Remote parking is also possible with the auto-
matic parking system plus with remote mem-
ory function (My CUPRA App).
The driver carries the vehicle’s key during
parking. The vehicle’s Keyless Access system
must be active and the mobile app should be
used.
The parking system takes charge of the vehi-
cle's steering, gear changes, acceleration and
braking ›››
, ››› .
Function button on the screen of the info-
tainment system.
Functions available for remote parking
with the automatic parking system plus.
●
Select and change the parking mode.
●
Drive to the appropriate parallel or bay park-
ing space.
●
Manoeuvring out of a suitable parallel or bay
parking space.
In the case of a parallel parking space, for
safety reasons, the driver and other occupants
or pets must be positioned out of the way of
the vehicle's manoeuvres.
Remote parking functions available with
the automatic parking system with remote
memory function (My CUPRA App)
●
Parking in a space that has been saved in the
infotainment system.
●
Close the windows by pressing and holding
the “Close windows” button in the App.
The driver must monitor the area around the
vehicle at all times ››› .
Please note that automatic braking may occur
if there are obstacles in the vehicle's path or
if a dangerous situation arises ›››page229,
Automatic brake operation.
WARNING
The automatic parking system Plus with re-
mote parking is no substitute for the driver's
attention and only works within the limits of
the system. The parking system cannot de-
tect all driving situations and may not react
at all or may react with a delay or in an un-
desired manner. If the driver does not pay
attention, there is a risk of accidents and se-
rious or even fatal injuries.
●
Always pay proper attention and do not
rely solely on the system. The driver is always
responsible for all driving tasks.
●
Carefully observe the remote parking proc-
ess from outside the vehicle and cancel the
parking in the CUPRA App if a dangerous sit-
uation arises.
●
Only park/unpark the vehicle if you hold a
valid driving licence.
●
Follow the traic regulations of the coun-
try you are in.
●
Leave the driver seat only when the vehicle
asks you to do so.
246
Parking and manoeuvring
●
Do not use the parking system in parking
spaces without structural boundaries (for ex-
ample, nearby bodies of water, riverbanks or
embankments without barriers).
WARNING
The system is only capable of a limited re-
sponse to sudden changes in external condi-
tions. Collisions with other road users may
occur.
●
Do not use the parking system when traic
speeds are in excess of 50 km/h (30 mph).
●
Always keep a safety distance of at least
one vehicle length at junctions.
●
Do not perform automatic parking from
the other side of the road or across several
lanes.
WARNING
The vehicle may roll or move into the path
of oncoming traic, which could lead to acci-
dents with damage to the vehicle and serious
or fatal injuries.
●
Do not stand in the path of the vehicle.
●
Carefully observe the parking process and
the traic and cancel the parking in the
CUPRA App if a dangerous situation arises.
WARNING
The parking process cannot be carried out
correctly if the roadway is slippery; the vehi-
cle may skid. This can lead to accidents with
damage to the vehicle and serious injuries.
●
Do not use the parking system to park on
frozen or icy roads.
NOTICE
The parking system may suggest parking
spaces that are not suitable for the parking
process due to a lack of boundaries or due to
adjacent objects. This can cause damage to
the vehicle.
●
Do not park next to protruding objects, for
example, loading ramps and parked trailers,
or under overhanging objects.
●
Pay close attention to the parking process
in multi-storey car parks where the parking
space is surrounded by pillars.
CUPRA remote parking app
The CUPRA app for the automatic parking sys-
tem plus with remote function is available in
App Stores ›››
, ››› .
WARNING
The operation of the vehicle may be restric-
ted if an incompatible mobile phone is used
(e.g. delayed reaction of the vehicle during
remote parking). This may result in damage
to the vehicle and serious injury.
●
Check compatibility information in your
mobile phone's app.
1. Install and run the My CUPRA App on a
compatible mobile phone.
2. Synchronise the mobile phone with the ve-
hicle.
NOTICE
The remote parking function may not work
properly if the mobile phone is damaged (e.g.
the touch screen is damaged) or if the func-
tions are restricted (e.g. delayed reactions to
operation). This can lead to accidents result-
ing in vehicle damage and injuries.
●
Only use a compatible and fully operational
mobile telephone.
NOTICE
Technical manipulation by the user may in-
terfere with the remote parking process,
which may lead to accidents resulting in vehi-
cle damage and injury.
●
Do not make any modications to the soft-
ware, the mobile phone, its operating system
or the vehicle.
Parking and manoeuvring
247
Automatic parking system plus with remote function (My CUPRA App)
Synchronising and connecting a
mobile
The mobile must be synchronised with the ve-
hicle via Bluetooth®.
To continue using the CUPRA app, the mobile
device only needs to be connected to the ve-
hicle via Bluetooth®.
Synchronising a mobile with the vehicle
1. Switch the ignition on.
2. Tap the infotainment system function but-
ton
.
3. Press Settings.
4. Select the option Remote Controlled
Parking with My CUPRA App.
5. Scan the QR code with the My CUPRA App.
The mobile is synchronised.
6. See the My CUPRA App for further infor-
mation.
Cancel synchronisation between the mobile
and vehicle
Remote parking is no longer possible as soon
as the synchronisation has been cancelled in
the App or in the vehicle.
Mobile and app data can be deleted from the
infotainment system.
●
Tap the infotainment system function button
.
●
Delete the mobile from the Remote Con-
trolled Parking with My CUPRA App menu in
Settings.
To cancel the synchronisation completely, also
delete the vehicle from the My CUPRA App.
Driving to and from a parking
space
Prerequisites
●
There is a Bluetooth® connection between
the vehicle and the mobile.
●
The vehicle key is in the driver's hands.
●
Automatic Parking System Plus: A car park
space has been found and selected in the Info-
tainment system.
●
Automatic parking system Plus with memory
and remote function: A saved parking process
(car park space) has been detected nearby the
vehicle.
●
The driver must park the vehicle at a dis-
tance of no more than 6 metres from the park-
ing space in order to park it remotely ››› .
The driver must never be in the path of the
vehicle, as this could result in damage or injury
to persons.
Driving to a car park space
If the function button appears on the screen
of the parking system, the parking process can
be carried out using the mobile.
1. To park remotely, tap the function button
in the infotainment system. The function
is activated.
2. Exit the vehicle as soon as possible, as
the function is deactivated after a certain
amount of time has elapsed. If necessary,
take all the vehicle keys with you.
3. Check the driving route and start the park-
ing process with the My CUPRA App ››› .
When the parking process is complete, a
text message is displayed in the My CUPRA
App.
The electronic parking brake is applied in
the vehicle and the vehicle's drive system is
deactivated.
WARNING
The parking process may be interrupted if
the driver is too far away from the vehicle,
which can lead to accidents and serious inju-
ries.
●
Remain in a safe and suitable position in
the vicinity of the vehicle.
Exiting the parking space
This function is only available for the automatic
parking system plus.
248
Parking and manoeuvring
1. Open the My CUPRA App.
2. Activate the vehicle's drive system with My
CUPRA App.
3. Select the desired parking mode.
4. Check the driving route and start the proc-
ess for exiting the parking space with the
My CUPRA App.
5. When the parking space exit process is
complete, take control of the vehicle to
continue driving and look at the text mes-
sages on the infotainment system ››› .
WARNING
When exiting a parking space, there is a risk
that the vehicle could drive into traic, which
could result in an accident and serious or fa-
tal injuries.
●
Ensure that the vehicle leaves the parking
space only when the traic situation permits.
Reverse Assist (Rear View
Camera)
Introduction
A camera installed in the rear lid handle assists
the driver with reverse parking or manoeuvring
›››page198.
The camera image is viewed together with ori-
entation lines projected on the Infotainment
system display. Part of the bumper can be seen
at the bottom, which can be used by the driver
as a reference point.
Reverse assist modes
Depending on the equipment, the following
modes are available:
●
Angle parking: reverse parking perpendicu-
lar to the road.
●
Trailer towing assist function: assistance
with hitching a trailer.
●
Cross traic: monitors cross traic.
Requirements
To park with reverse assist, the following re-
quirements must be met:
●
Do not exceed a speed of approx. 15km/h
(9mph).
●
Parking space width: vehicle width + 0.15 m
(without counting the mirrors).
To display a real image, the following require-
ments must be met:
●
The luggage compartment rear door is
closed.
●
The surroundings are on a at surface.
●
The vehicle should not be loaded very heav-
ily at the rear.
WARNING
●
The reverse assist does not make it possi-
ble to precisely calculate the distance from
obstacles and nor can it overcome the sys-
tem's own limits, hence its negligent use may
cause serious accidents and injuries if used
without due care. The driver should be aware
of his/her surroundings at all times to ensure
safe driving.
●
The camera lens expands and distorts the
eld of view and displays the objects on the
screen in a way that is dierent from reality.
Distance perception is also distorted.
●
Due to the screen resolution or light con-
ditions, some items may be blurry or not dis-
played at all. Take care with thin posts, fen-
ces, railings or trees that might not be seen
on the screen and could damage the vehicle.
●
The reverse assist has blind spots where
it cannot see people or objects. Monitor the
vehicle's surrounding area at all times.
●
The system is not a replacement for driver
awareness. Supervise the parking manoeu-
vre and the vehicle's surrounding area at all
times.
●
Do not be distracted from the traic by
looking at the screen.
●
The images are only two-dimensional. Pro-
truding objects or holes in the road, for ex-
ample, are more diicult to detect or may not
be seen at all.
Parking and manoeuvring
249
Reverse Assist (Rear View Camera)
●
Vehicle load modies the representation of
the guide lines. The width represented by the
lines decreases with vehicle load. Pay special
attention to the surroundings when the in-
side of the vehicle or the luggage compart-
ment are loaded.
●
In the following situations, objects or other
vehicles appear to be further away or closer
than they actually are. Pay special attention:
–
If moving from a at surface to a slope
and vice-versa.
–
If the vehicle is heavily loaded.
–
When the vehicle approaches objects
that are not on the ground surface or that
protrude from it. These objects may be
outside the camera angle when reversing.
Note
●
It is important to take great care and pay
special attention if the driver is not familiar
with the system.
●
The reverse assist reference lines disap-
pear when the rear lid is open.
Connecting and disconnecting
Connect the reverse assist
●
With the ignition switched on, select reverse
gear.
●
OR: in the infotainment system select >
Driver assist > Park assist.
Disconnect the reverse assist
●
Drive forward at a speed of at least 15 km/h
(9 mph).
Shown on the display
The system’s functions and representations
may vary depending on the equipment.
The assistant's image view changes when the
factory-tted tow hitch is electronically con-
nected to a trailer ›››
page322.
Reverse assist functions and symbols
When the reverse assist is connected, you can
make adjustments using the function buttons.
Some adjustments are equipment-dependent.
Exit the current display
Switch to angle parking ›››page250
Switch to the trailer hitching assistance
function
Switch to cross traic
Adjust the display: brightness, contrast
and colour.
Switch to park assist ›››
page231
Display/hide the park assist view
Guide lines
Green horizontal lines: extension of the vehi-
cle.
Yellow lines: vehicle path depending on the
steering angle.
Assistance function for hitching a trailer
On vehicles with a factory-tted towing device,
this function can be used to move the vehicle
close to a tow bar.
Auxiliary lines are shown in the infotainment
system.
Green lines: distance to the trailer hitch. The
distance between the lines is approx. 0.30 m
Yellow line: pre-calculated direction of the
trailer hitch depending on how the steering
wheel is turned.
Cross traic
This view helps to monitor traic behind the
vehicle and can be used, for example, when
exiting garages or narrow exits.
250
Parking and manoeuvring
1
2
3
4
Angle parking
Fig.161 Display on the infotainment
system screen: parking with the reverse
assistant.
Key to ›››
Fig.161:
Find a parking space
Go to the selected parking space
Centre the vehicle inside the parking
space
Road
Parking space
Side boundary of the parking space
Rear boundary of the parking space
Parking
●
In the infotainment system select > Driver
assist > Park assist before passing in front of
the selected parking space.
●
With reverse assist connected and in opera-
tion, press the function button .
●
Stop the vehicle in front of the parking space
›››Fig.161
2
.
●
Reverse while turning the steering wheel so
that the yellow lines enter the parking space.
The green and yellow lines must match the
side boundary lines
3
.
●
Stop the vehicle when the red line has
reached the rear boundary
4
.
Troubleshooting
The system behaves dierently than expec-
ted
There can be several causes:
●
The camera is dirty ›››page395. In addi-
tion to dirt and snow, camera visibility can be
reduced by detergent residue or any type of
coating.
●
The system requirements must be met
›››
page248.
●
The camera is covered with water.
●
The factory-tted towing bracket must
not be electrically connected to a trailer
›››page322.
●
The vehicle has some type of damage in the
camera area, e.g. due to a parking impact.
●
The eld of view of the camera is blocked by
an accessory, e.g. a bicycle carrier system.
●
Changes have been made to the paint in the
camera area, or structural modications have
been made to a component such as the run-
ning gear.
Camera with no visibility, fault message, the
system disconnects
●
Clean the camera or remove any stickers or
accessories from it ›››page395.
●
Check for visible damage.
Possible solution
●
Temporarily disconnect the system.
●
Check if one of the causes indicated above
has occurred.
●
Once the source of the problem has been
eliminated, the system may be reconnected.
●
If the system still behaves unpredictably,
have it checked by a specialised workshop.
Parking and manoeuvring
251
Peripheral view system (Top View Camera)
A
Peripheral view system
(Top View Camera)
Introduction
Using 4 cameras, the system generates a rep-
resentation that is shown on the infotainment
system display. The cameras are located on the
radiator grille, the exterior mirrors and the rear
lid.
The functions and representations of the Area
View system may vary depending on whether
or not the vehicle has ParkPilot.
WARNING
The image from the cameras does not make
it possible to calculate the distance to the
obstacles (people, vehicles, etc.) precisely,
so using them could cause serious accidents
and injury.
●
The camera lenses augment and distort the
visual eld and the objects on the screen are
seen dierently and imprecisely.
●
Certain objects may not be shown or may
not be shown very clearly, for example, posts
or thin rails, due to the screen resolution or if
light conditions are insuicient.
●
The cameras have blind spots in which ob-
stacles and people are not registered.
WARNING
The smart technology incorporated into the
Top View Camera system cannot overcome
the limits imposed by the laws of physics
and it only works within the limits of the sys-
tem. The greater convenience provided by
the Area View system should never tempt
you to take any risk that may compromise
safety. If used negligently or involuntarily,
it may cause serious accidents and injuries.
The system is not a replacement for driver
awareness.
●
Adapt your speed and driving style to
suit visibility, weather, road and traic condi-
tions.
●
Do not be distracted from the traic by
looking at the screen.
●
Monitor the area around the vehicle at
all times, since the cameras do not capture
small children, animals and certain objects in
all situations.
●
The system will probably be unable to rep-
resent all areas clearly.
NOTICE
●
The camera images are only two-dimen-
sional. Due to a lack of spatial depth, objects
that jut out or holes on the road, for exam-
ple, are more diicult to detect or may not be
seen at all.
●
In certain circumstances, the camera does
not capture objects such as beams, fences,
posts or thin trees, which could damage the
vehicle.
●
The system displays the auxiliary lines and
boxes regardless of the vehicle's surround-
ings and whether or not objects are detec-
ted. The driver is responsible for determining
that the vehicle will t in the parking space.
Area View system
Fig.162 Display of the Area View system:
aerial view.
There are four dierent views to choose from
›››
Fig.162:
Front camera area
252
Parking and manoeuvring
B
C
D
Right camera area
Rear camera area
Left camera area
Function buttons:
Depending on the equipment: connect-
ing and disconnecting the ParkPilot
sound.
The aerial view is generated by combining the
images from all the cameras ›››Fig.162.
The top view can be selected by pressing the
vehicle inside the zone.
The system will automatically switch between
front and rear camera view according to the
direction of travel.
Press on the dierent areas ›››Fig.162
A
to
D
of the top view or reduced top view to select
and set the corresponding view, which will be
highlighted in orange.
Conditions necessary for the use of the Area
View system
●
The doors and the rear lid must be closed.
●
The image must be reliable and clear. For this
reason, for example, the camera lens must be
clean.
●
The area around the vehicle must be clearly
and totally visible.
●
The area for parking or manoeuvring should
be a at surface.
●
The vehicle should not be loaded very heav-
ily at the rear.
●
The driver must be used to the system.
●
There should be no damage to the vehicle in
the camera area. If the position or installation
angle of the cameras have been changed, e.g.
after a rear-end collision, the system should be
checked by a specialised workshop.
Special characteristics
The images on the area view system cameras
are only two-dimensional. Due to a lack of spa-
tial depth, it is diicult or impossible to make
out on-screen any holes there may be on the
ground, objects jutting out from the ground or
parts protruding from other vehicles.
Situations in which the objects or other vehi-
cles appear to be further away or closer than
they really are:
●
On moving from a horizontal plane to a
slope.
●
On moving from a slope to a horizontal
plane.
●
If the vehicle is heavily loaded at the rear.
●
If the vehicle approaches protruding objects.
These objects may be outside the cameras'
angle of visibility.
Trailer mode
The Area View system conceals, in the rear
camera area, all the auxiliary guiding lines
when the factory-tted towing bracket is con-
nected electrically to a trailer ›››page322.
Note
To become familiar with the system and
its functions, CUPRA recommends that you
practice handling the Area View system in an
area where there is not too much traic or in
a car park.
Connecting and disconnecting
Connecting
●
Select reverse gear.
●
OR: in the infotainment system select >
Assistants > Parking assistant > Park assist.
Switching o
●
Drive forward at a speed of at least 15 km/h
(9 mph).
●
OR: press the function button.
Views of the peripheral vision sys-
tem (modes)
The red lines indicate a distance of approx. 40
cm away from the vehicle.
Parking and manoeuvring
253
Trailer Assist
Top views (bird's eye view)
Main mode:
The vehicle and its immediate vicinity
seen from above are shown. Depending
on the equipment, the ParkPilot's path
may also be displayed.
Front camera views (front view)
Cross traic.
This visualization helps to monitor traic
to the left, front and right of the vehicle
and can be used, for example, when ex-
iting garages or narrow exits
Angle parking.
The area in front of the vehicle is shown.
Orientation lines are shown to give guid-
ance.
Side camera views (side view)
Right and left sides.
The areas located directly to the side of
the vehicle seen from above are repre-
sented in order to navigate possible ob-
stacles more precisely.
Rear camera views (rear view)
Angle parking.
The area behind the vehicle is shown.
Auxiliary lines are shown to give guid-
ance.
Trailer coupling assistance function.
On vehicles with a trailer coupling assis-
tance function, the function will provide
guidance to facilitate hitching the trailer.
Auxiliary lines are shown in the infotain-
ment system.
Green lines: distance to the trailer hitch.
The distance between the lines is approx.
0.30 m
Yellow line: pre-calculated direction of the
trailer hitch depending on how the steer-
ing wheel is turned.
Cross traic.
This visualization helps to monitor traic
to the left, front and right of the vehicle
and can be used, for example, when ex-
iting garages or narrow exits.
Trailer Assist
Introduction
Trailer assist helps the driver to reverse and
manoeuvre with a trailer.
By moving the rotary knob of the exterior mir-
rors, the trailer assist directs the trailer that is
hitched. The driver has to accelerate, change
gears and brake!
System limitations
Under certain circumstances, the camera does
not detect objects such as trailer draw bars,
bars, fences, posts or thin trees, or an open
(or opening) rear lid, which could damage the
vehicle.
In order to guarantee good system operation,
keep the camera clean, free of snow or ice,
and do not cover it with stickers or other ob-
jects. Do not allow the draw bar to be covered
by external inuences.
Use the trailer manoeuvre assistant only when
the rear lid is closed correctly.
NOTICE
The trailer maneuver assistant does not take
the vehicle’s surrounding as a reference. No
obstacle detection takes place. The driver
alone has to assess whether it is possible to
manoeuvre safely with the tow vehicle and
trailer set.
●
Always observe the movement of the
trailer and, if necessary, actively interrupt
the manoeuvre to avoid damage. Even if
the trailer manoeuvring assistant is operated
correctly, on rare occasions the trailer may
move in a dierent way to the setting.
●
Do not rely solely on the indications on the
instrument cluster display.
254
Parking and manoeuvring
1
2
3
4
5
6
7
Note
The trailer manoeuvre assistant automati-
cally switches o approx. 10 minutes after
being activated. The assistant is also deacti-
vated if the driver does not perform any ac-
tion over the course of approx. 3 minutes.
Requirements
The following requirements must be met for
the trailer manoeuvre assistant to work:
●
The engine is running.
●
The ESC must be connected.
●
The driver's door and the rear lid are closed.
●
The exterior mirrors are not folded.
●
There is a non-articulated one or two axle
trailer hitched and electrically connected.
●
Both the tow vehicle and trailer are stopped.
●
The maximum bending angle has not been
exceeded.
●
The length of the trailer’s drawbar has been
determined.
Determine the length of the trailer's draw-
bar
In order for the trailer manoeuvre assistant
to determine the length of the trailer’s draw-
bar, drive the vehicle-trailer set through some
turning manoeuvres or curves. The more pre-
cisely the length of the drawbar is determined,
the wider the angles that will be available
when manoeuvring. The assistant subdivides
the maximum available end stops of the angle
indicator into four levels: approx. 30°, 45°, 60°
and 75°.
Note
For technical reasons, the trailer manoeuvre
assistant cannot always correctly detect trail-
ers with LED technology taillights.
Operating
Fig.163 Outside rearview mirror rotary
control: adjust the trailer angle.
Fig.164 Instrument cluster display:
engage reverse.
Key to the ›››
Fig.163 , ›››Fig.164:
Rotary exterior mirror controls.
Trailer orientation to the left
Trailer orientation to the right
Move the vehicle in the direction of the
towing device.
Actual trailer position
Target trailer position
Angle indicator zero position
Manoeuvre with the tow vehicle and trailer
set
The system requirements must be met
›››
page254.
Parking and manoeuvring
255
Trailer Assist
●
Select reverse gear.
●
Press the infotainment system button >
Assistants > Parking > Trailer As-
sist.
●
Let go of the steering wheel ››› .
●
Tilt the rotary control until the desired direc-
tion is reached ›››Fig.163. A representation
of the tow vehicle and trailer set is shown
on the instrument cluster screen for guidance
purposes ›››Fig.164.
●
Reverse by accelerating slowly. Pay attention
to your surroundings!
●
If necessary, correct the angle with the ro-
tary control. Press the control towards the left
or right: the set will move to the left or right.
Press the control backwards: the vehicle will
follow the trailer.
●
Reverse and move forwards until the desired
position is reached.
●
The manoeuvre ends when a message is dis-
played on the instrument cluster display and, in
some cases, an audio signal sounds.
Automatic brake operation
The trailer manoeuvre assistant helps the
driver by automatically operating the brakes in
certain situations.
The driver is responsible for braking on
time›››
.
The brakes may be applied automatically and
the function deactivated in the following situa-
tions:
●
A certain speed is exceeded.
●
The steering wheel is grabbed. The vehicle
brakes automatically until it stops.
●
If the button is pressed during the ma-
noeuvre or the driver’s door opens.
WARNING
The quickly turning steering wheel can cause
serious injuries.
●
Do not hold the steering wheel during the
manoeuvre until the system requests it.
●
Exception: If a dangerous situation occurs,
intervene and take over the steering.
WARNING
Never allow the automatic operation of
brakes to lead you to take any risk that com-
promises safety. The system is not a replace-
ment for driver awareness.
●
The manoeuvre assist system is subject to
certain limitations inherent to the system. In
certain situations, the automatic braking in-
tervention may only work in a limited way or
not work at all.
●
Always be ready to use the brakes yourself!
●
Automatic brake operation ends after 1.5
seconds approx. if the vehicle is stopped. Af-
ter this, brake the vehicle yourself.
Note
The exterior mirrors cannot be adjusted
while the assistant is active. The saved set-
ting for the passenger’s mirror can be activa-
ted ›››page142.
Troubleshooting
Camera with no visibility, fault message, the
system disconnects
●
Clean the camera or remove any stickers or
accessories from it ›››page395.
●
Check for visible damage.
The system behaves dierently than expec-
ted
There can be several causes:
●
The camera is dirty ›››page395. In addi-
tion to dirt and snow, camera visibility can be
reduced by detergent residue or any type of
coating.
●
The system requirements must be met
›››page254.
●
The camera is covered with water.
●
The vehicle has some type of damage in the
camera area, e.g. due to a parking impact.
●
The eld of view of the camera is blocked by
an accessory, e.g. a bicycle carrier system.
256
Parking and manoeuvring
1)
It is only displayed if the vehicle is equipped with a parking system.
●
Changes have been made to the paint in the
camera area and structural modications have
been made, e.g. to the front part of the vehicle
and the running gear.
Solution for all cases
●
Temporarily disconnect the system.
●
Check if one of the causes indicated above
has occurred.
●
Once the source of the problem has been
eliminated, the system may be reconnected.
●
If the system still behaves unpredictably,
have it checked by a specialised workshop.
Rear Cross Traic Alert
How it works
Fig.165 Park assist diagram: detected area
around the vehicle that is driving o.
Park Assist uses the radar sensors on the rear
bumper ›››
page197 to monitor traic cross-
ing behind the vehicle as it reverses out of a
parking bay, or as it is being manoeuvred, for
example in very low visibility conditions.
When the system detects a relevant vehicle on
the road that is approaching the rear of the
vehicle ›››Fig.165, an audio alarm may sound
if the vehicle is suiciently relevant.
In addition to the audio alarm, the driver is
also informed by means of a visual signal on
infotainment system display. This signal is dis-
played in the form of a red strip at the back of
the image of the vehicle on the infotainment
system display. This strip displays the side of
the vehicle towards which traic is approach-
ing in a cross-wise direction
1)
.
Automatic braking to reduce damages
›››
page229.
Connecting and disconnecting
The rear cross traic alert can be activated
and deactivated by accessing the Assistants
menu of the infotainment system. It can also
be found in the Park Assist Settings menu.
Additionally it can be switched on and o by
accessing the Assistants menu on the instru-
ment cluster.
When the vehicle is restarted, the last adjust-
ment in the system will remain active.
Trailer mode
The rear cross traic alert will be automatically
deactivated and it will be impossible to activate
them if the tow hitch is electrically connected
to a trailer or other similar object. As soon as
the driver starts driving, a message appears on
the instrument cluster display indicating that
the assistant is deactivated.
Once the trailer is uncoupled from the vehicle,
the assistant will return to its initial state prior
to the moment when the trailer was electrically
connected.
Parking and manoeuvring
257
Exit Warning
If the tow hitch is not factory tted, then the
rear cross traic alert will have to be deactiva-
ted manually when driving with a trailer.
WARNING
The smart technology incorporated into the
rear cross traic alert cannot overcome the
limits imposed by the laws of physics; it only
works within the limits of the system. The
park assist function should not tempt you
into taking any risks. The system is not a re-
placement for driver awareness.
●
The system should never be used in limi-
ted visibility conditions or complicated traf-
c, e.g., in high-traic areas or when crossing
multiple lanes.
●
Be sure to always be aware of the vehicle's
surroundings, since the system often fails to
detect things such as bicycles or pedestrians.
●
The rear cross traic alert itself will not
brake the vehicle to a complete stop.
Exit Warning
How it works
Fig.166 Illustrated example.
Fig.167 Door: warning lamp
The door opening warning (Exit Warning)
warns occupants of a possible collision when
opening the door when the vehicle is station-
ary.
The system monitors, within the limits of
the system itself, the rear and side environ-
ment of the vehicle using the rear sensors
›››
page197. It detects moving objects
that approach from behind, such as cars
›››Fig.166.
If a critical situation is detected when the door
is opened, an alert is given by an audible signal
from the door speaker on the corresponding
side ›››Fig.167. The side assist control lamp
on the side of the corresponding door will also
ash. If the door has already been opened and
another road user has been detected in a crit-
ical situation, the control lamp of the lane de-
parture warning on the corresponding side will
light up permanently.
The door opening assistant control lamps can
be set to up to 5 dierent brightness levels by
accessing the Side Assist menu.
When you want to access the vehicle for the
rst time, with the doors closed and locked,
the function will be available 3 minutes after
the rst opening of any of the doors. The func-
tion will continue to be available as long as the
vehicle has the ignition connected and is not
moving.
After switching o the ignition, the function will
remain available for approximately 3 minutes.
258
Parking and manoeuvring
Connecting and disconnecting
The door opening assistant can be switched on
and o by accessing the Assistants menu in
the infotainment system. It can also be found
in the Park Assist Settings menu.
When the vehicle is restarted, the last adjust-
ment in the system will remain active.
Trailer mode
The door opening assistant will be automati-
cally deactivated and it will be impossible to
activate it if the tow hitch is electrically con-
nected to a trailer or other similar object.
Once the trailer is uncoupled from the vehicle,
the assistant will return to its initial state prior
to the moment when the trailer was electrically
connected.
If the tow hitch is not factory tted, then the
door opening assistant will have to be deacti-
vated manually when driving with a trailer.
WARNING
●
Always pay close attention to the traic
and the surroundings of the vehicle. The
door opening warning (Exit Warning) cannot
replace the necessary attention to be paid
by the vehicle’s occupants. Responsibility for
opening the doors and exiting the vehicle al-
ways lies with its occupants.
●
The door opening warning (Exit Warning)
operates continuously as long as the vehicle
ignition is on. Otherwise, the system is deac-
tivated and the lamps light up briey.
●
It is possible that the traic situation is not
interpreted correctly the system cannot be
aware of all the objects that are approaching,
such as pedestrians. Always visually monitor
the traic and the area surrounding the vehi-
cle.
WARNING
The door opening warning (Exit Warning) is
subject to system limits and cannot warn of
an imminent collision in all cases:
●
If your vehicle is too deep in the parking
space and the adjacent vehicles hide it.
●
In certain circumstances, objects or people
who approach, e.g. on a bicycle or scooter,
are not detected.
●
The system does not react to stationary ob-
jects.

Related Topics

Popular Owner Manuals