2024-2026 Cupra Terramar SUV Parking and manoeuvring -> Electronic parking brake User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Parking and manoeuvring -> Electronic parking brake for Your Cupra Terramar SUV First Generation (2024-2026)

226
Parking and manoeuvring
NOTICE
Components on the underside of the vehicle,
such as bumpers, spoilers and running gear
components, can be damaged when running
over objects protruding from the ground.
●
Drive carefully when entering buildings, on
ramps, driving over kerbs or xed markings,
and on descents.
NOTICE
Avoid parking the vehicle where the hot ex-
haust system could ignite inammable mate-
rials, such as dry grass, low bushes, spilt fuel
or ammable materials.
Electronic parking brake
Using the electronic parking brake
Fig.148 Centre console, lower part:
electronic parking brake button.
Connecting
The electronic parking brake can be activated
whenever the vehicle is at a standstill, even
when the ignition is switched o. Activate it
whenever you leave or park the vehicle.
●
Pull and holdthe button ›››Fig.148.
The parking brake is on when the red indicator
lamp on the instrument cluster and the but-
ton indicator lamp turns on.
●
Release the button.
Switching o
●
Switch the ignition on.
●
Press the button ›››Fig.148. At the same
time step hard on the brake pedal or, if the
engine is running, press the accelerator pedal
slightly.
●
The indicator lamp on button and thered in-
dicator lamp on the instrument cluster turn
o.
Automatic disconnection when moving o
The electronic parking brake automatically dis-
connects when moving o in any of the follow-
ing situations, if the driver's door is closed and
the driver's seatbelt is buckled:
●
Vehicles with an automatic gearbox: A gear
range is engaged or switched to another one
and the accelerator pedal is lightly pressed.
●
To facilitate certain manoeuvres, there are
exceptions that allow the parking brake to
disconnect automatically without the driver's
seatbelt being buckled.
The parking brake can be prevented from
being automatically released by continuously
pulling up the switch when moving o.
The electronic parking brake is not disconnec-
ted until the
button is released. This can fa-
cilitate starting o when a heavy load is towed
›››page322.
Parking and manoeuvring
227
Electronic parking brake
Automatic application when exiting the ve-
hicle incorrectly
In vehicles with automatic transmission, the
electronic parking brake may be applied auto-
matically if the system detects an improper at-
tempt to exit the vehicle. For example:
●
no seat presence detection,
●
seat belt unfastened,
●
door open.
The electronic parking brake also holds the ve-
hicle in the neutral N position.
WARNING
If the vehicle is left incorrectly, it could roll
away. This could lead to accidents, serious
injury and property damage.
●
When parking the vehicle, always perform
the appropriate operations in the indicated
order ›››page225, Parking.
●
Before leaving the vehicle, make sure that
the electronic parking brake is applied and
that the control lamp next to the gear se-
lector is red on the instrument cluster.
Protection against unintentional movement
If you do not want the electronic parking brake
to be applied automatically, e.g. in a car wash
or if you want to push or tow the vehicle, the
vehicle’s ability to roll can be maintained .
Deactivate:
With the vehicle stationary, press down the
brake pedal and select the N position on the
gear selector.
●
Conrm the message Deactivate roll-away
protection in the infotainment system.
●
OR: open the vehicle settings in the infotain-
ment system > Vehicle > Brakes > Deacti-
vate the “Roll-away protection function”.
Activate:
●
Press the button ›››Fig.148. The elec-
tronic parking brake is activated.
NOTICE
The vehicle may be able to roll even when the
ignition is switched o.
Automatic connection when the ignition is
turned o
This function can be deactivated through the
Infotainment system.
Emergency brake function
Only use the emergency brake function in an
emergency, if the vehicle cannot be stopped
by pressing the brake pedal ›››
!
●
Pull and holdthe button. The vehicle
will brake sharply. At the same time, an audio
warning will be heard.
●
To stop the braking process, release the but-
ton or press the accelerator.
When the ESC Sport or ESC OFF mode is se-
lected, ESC will reactivate to assist the driver
during braking. Depending on the model ver-
sion, the ESC will either switch back to its previ-
ous disconnected state or will remain on.
WARNING
Improper use of the electronic parking brake
can cause accidents and serious injury.
●
Never use the electronic parking brake to
stop the vehicle, unless it is an emergency.
The braking distance is considerably longer.
Always use the brake pedal.
●
Never accelerate from the engine when a
gear range or a gear is engaged and the en-
gine is running. The vehicle could start mov-
ing even when the electronic parking brake is
engaged.
NOTICE
To prevent the vehicle from unintentionally
moving when parking it, rst apply the elec-
tronic parking brake and then remove your
foot from the brake pedal.
Troubleshooting
There is a defect in the electronic park-
ing brake
The control lamp lights up in yellow.
228
Parking and manoeuvring
Visit a CUPRA dealer or other specialist work-
shop.
The electronic parking brake does not re-
lease.
The 12-volt battery is discharged.
●
Use the jump start ›››page340.
The electronic parking brake makes noises
●
When the electronic parking brake is applied
and released, noises may be heard.
●
The system performs automatic and audi-
ble checks sporadically in the parked vehicle
if some time elapses without the electronic
parking brake being used.
AutoHold function
Fig.149 In the lower part of the centre
console: AutoHold function button.
The Auto Hold function holds the vehicle at a
standstill and prevents it from moving without
it being necessary to keep the brake pedal de-
pressed.
When the Auto Hold function is
switched on, the lamp on the instru-
ment cluster lights up grey.
When the Auto Hold function is active,
the control lamp on the instrument
cluster lights up green.
The control lamp of the
button ›››Fig.149
remains on when the Auto Hold function is
connected.
Requirements
●
If the system has detected the driver’s pres-
ence based on various signals such as: seat-
belt, driver’s door, driver’s seat occupied and
others.
●
The engine is running.
Connecting and disconnecting
Press the Auto Hold button ››› . The control
lamp on the button turns on when the Auto
Hold function is switched on. The function is
now available to be activated. The lamp on the
button goes out when the Auto Hold function
is switched o.
Switching on and o automatically
If the Auto Hold function was switched on with
the Auto Hold button before switching o the
ignition, the function will remain on after the
ignition is re-engaged.
If the Auto Hold function was not switched
on, it will remain o next time the ignition is
switched on.
The Auto Hold function is automatically turned
o if the following conditions are met:
1. If any of the requirements of the function
are no longer met.
2. If the engine runs erratically or has any
anomaly.
3. Automatic gearbox: If any of the tyres have
only minimal contact with the ground, e.g.,
if the axles are crossed.
The Auto Hold function is temporarily switched
o while the user pulls the electronic parking
brake button .
Activation and deactivation
The Auto Hold function activates automatically
if the following conditions are met (all points
must be met at the same time):
1. The function is switched on
2. The vehicle is brought to a complete
standstill with the brake pedal on a at sur-
face or on a slope.
3. The engine rotates “correctly”.

Related Topics

Popular Owner Manuals