2024-2026 Cupra Terramar SUV Parking and manoeuvring -> Reverse Assist (Rear View Camera) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Parking and manoeuvring -> Reverse Assist (Rear View Camera) for Your Cupra Terramar SUV First Generation (2024-2026)

248
Parking and manoeuvring
1. Open the My CUPRA App.
2. Activate the vehicle's drive system with My
CUPRA App.
3. Select the desired parking mode.
4. Check the driving route and start the proc-
ess for exiting the parking space with the
My CUPRA App.
5. When the parking space exit process is
complete, take control of the vehicle to
continue driving and look at the text mes-
sages on the infotainment system ››› .
WARNING
When exiting a parking space, there is a risk
that the vehicle could drive into traic, which
could result in an accident and serious or fa-
tal injuries.
●
Ensure that the vehicle leaves the parking
space only when the traic situation permits.
Reverse Assist (Rear View
Camera)
Introduction
A camera installed in the rear lid handle assists
the driver with reverse parking or manoeuvring
›››page198.
The camera image is viewed together with ori-
entation lines projected on the Infotainment
system display. Part of the bumper can be seen
at the bottom, which can be used by the driver
as a reference point.
Reverse assist modes
Depending on the equipment, the following
modes are available:
●
Angle parking: reverse parking perpendicu-
lar to the road.
●
Trailer towing assist function: assistance
with hitching a trailer.
●
Cross traic: monitors cross traic.
Requirements
To park with reverse assist, the following re-
quirements must be met:
●
Do not exceed a speed of approx. 15km/h
(9mph).
●
Parking space width: vehicle width + 0.15 m
(without counting the mirrors).
To display a real image, the following require-
ments must be met:
●
The luggage compartment rear door is
closed.
●
The surroundings are on a at surface.
●
The vehicle should not be loaded very heav-
ily at the rear.
WARNING
●
The reverse assist does not make it possi-
ble to precisely calculate the distance from
obstacles and nor can it overcome the sys-
tem's own limits, hence its negligent use may
cause serious accidents and injuries if used
without due care. The driver should be aware
of his/her surroundings at all times to ensure
safe driving.
●
The camera lens expands and distorts the
eld of view and displays the objects on the
screen in a way that is dierent from reality.
Distance perception is also distorted.
●
Due to the screen resolution or light con-
ditions, some items may be blurry or not dis-
played at all. Take care with thin posts, fen-
ces, railings or trees that might not be seen
on the screen and could damage the vehicle.
●
The reverse assist has blind spots where
it cannot see people or objects. Monitor the
vehicle's surrounding area at all times.
●
The system is not a replacement for driver
awareness. Supervise the parking manoeu-
vre and the vehicle's surrounding area at all
times.
●
Do not be distracted from the traic by
looking at the screen.
●
The images are only two-dimensional. Pro-
truding objects or holes in the road, for ex-
ample, are more diicult to detect or may not
be seen at all.
Parking and manoeuvring
249
Reverse Assist (Rear View Camera)
●
Vehicle load modies the representation of
the guide lines. The width represented by the
lines decreases with vehicle load. Pay special
attention to the surroundings when the in-
side of the vehicle or the luggage compart-
ment are loaded.
●
In the following situations, objects or other
vehicles appear to be further away or closer
than they actually are. Pay special attention:
–
If moving from a at surface to a slope
and vice-versa.
–
If the vehicle is heavily loaded.
–
When the vehicle approaches objects
that are not on the ground surface or that
protrude from it. These objects may be
outside the camera angle when reversing.
Note
●
It is important to take great care and pay
special attention if the driver is not familiar
with the system.
●
The reverse assist reference lines disap-
pear when the rear lid is open.
Connecting and disconnecting
Connect the reverse assist
●
With the ignition switched on, select reverse
gear.
●
OR: in the infotainment system select >
Driver assist > Park assist.
Disconnect the reverse assist
●
Drive forward at a speed of at least 15 km/h
(9 mph).
Shown on the display
The system’s functions and representations
may vary depending on the equipment.
The assistant's image view changes when the
factory-tted tow hitch is electronically con-
nected to a trailer ›››
page322.
Reverse assist functions and symbols
When the reverse assist is connected, you can
make adjustments using the function buttons.
Some adjustments are equipment-dependent.
Exit the current display
Switch to angle parking ›››page250
Switch to the trailer hitching assistance
function
Switch to cross traic
Adjust the display: brightness, contrast
and colour.
Switch to park assist ›››
page231
Display/hide the park assist view
Guide lines
Green horizontal lines: extension of the vehi-
cle.
Yellow lines: vehicle path depending on the
steering angle.
Assistance function for hitching a trailer
On vehicles with a factory-tted towing device,
this function can be used to move the vehicle
close to a tow bar.
Auxiliary lines are shown in the infotainment
system.
Green lines: distance to the trailer hitch. The
distance between the lines is approx. 0.30 m
Yellow line: pre-calculated direction of the
trailer hitch depending on how the steering
wheel is turned.
Cross traic
This view helps to monitor traic behind the
vehicle and can be used, for example, when
exiting garages or narrow exits.
250
Parking and manoeuvring
1
2
3
4
Angle parking
Fig.161 Display on the infotainment
system screen: parking with the reverse
assistant.
Key to ›››
Fig.161:
Find a parking space
Go to the selected parking space
Centre the vehicle inside the parking
space
Road
Parking space
Side boundary of the parking space
Rear boundary of the parking space
Parking
●
In the infotainment system select > Driver
assist > Park assist before passing in front of
the selected parking space.
●
With reverse assist connected and in opera-
tion, press the function button .
●
Stop the vehicle in front of the parking space
›››Fig.161
2
.
●
Reverse while turning the steering wheel so
that the yellow lines enter the parking space.
The green and yellow lines must match the
side boundary lines
3
.
●
Stop the vehicle when the red line has
reached the rear boundary
4
.
Troubleshooting
The system behaves dierently than expec-
ted
There can be several causes:
●
The camera is dirty ›››page395. In addi-
tion to dirt and snow, camera visibility can be
reduced by detergent residue or any type of
coating.
●
The system requirements must be met
›››
page248.
●
The camera is covered with water.
●
The factory-tted towing bracket must
not be electrically connected to a trailer
›››page322.
●
The vehicle has some type of damage in the
camera area, e.g. due to a parking impact.
●
The eld of view of the camera is blocked by
an accessory, e.g. a bicycle carrier system.
●
Changes have been made to the paint in the
camera area, or structural modications have
been made to a component such as the run-
ning gear.
Camera with no visibility, fault message, the
system disconnects
●
Clean the camera or remove any stickers or
accessories from it ›››page395.
●
Check for visible damage.
Possible solution
●
Temporarily disconnect the system.
●
Check if one of the causes indicated above
has occurred.
●
Once the source of the problem has been
eliminated, the system may be reconnected.
●
If the system still behaves unpredictably,
have it checked by a specialised workshop.

Related Topics

Popular Owner Manuals