2004-2009 Hyundai Tucson SUV DO-IT-YOURSELF MAINTENANCE -> HEADLIGHT AIMING ADJUSTMENT User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

DO-IT-YOURSELF MAINTENANCE -> HEADLIGHT AIMING ADJUSTMENT for Your Hyundai Tucson SUV First Generation (2004-2009)

6
DO-IT-YOURSELF MAINTENANCE
33
2. Loosen the drain plug at the bot-
tom of the fuel filter.
3. Tighten the drain plug when water
no longer comes out.
4. Installation is the reverse order of
the disassembly.
5. Check to be sure that the warning
lamp illuminates when the ignition
key is turned to 'ON', and that it
goes off when the engine is started.
If in doubt, consult your nearest
authorized HYUNDAI dealer.
G300B01JM
!
WARNING:
Be sure to carefully wipe away any
water drained out in this manner,
because the fuel mixed in the wa-
ter might be ignited and result in a
fire.
NOTE:
It is recommended that water ac-
cumulated in the fuel filter should
be removed by an authorized
Hyundai dealer.
HEADLIGHT AIMING
ADJUSTMENT
G290A02O-GAT
Before performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground
and press the front bumper & rear
bumper down several times. Place
vehicle at a distance of 3,000 mm
(118 in.) from the test wall.
3. See that the vehicle is unloaded
(except for full levels of coolant,
engine oil and fuel, and spare tire,
jack, and tools). Have the driver or
equivalent weight placed in driver's
seat.
4. Clean the head light lenses and
turn on the headlights (low beam).
6
DO-IT-YOURSELF MAINTENANCE
34
5. Open the hood.
6. Draw the vertical line (through the
center of each headlight) and the
horizontal line (through the center
of each headlight) on the aiming
screen.
And then, draw a parallel line at 30
mm (1.18 in.) under the horizontal
line.
7. Adjust each cut-off line of the low
beam to the parallel line with a
phillips screwdriver - VERTICAL
AIMING.
8. Adjust each cut-off line of the low
beam to each vertical line with a
phillips screwdriver - HORIZON-
TAL AIMING.
G290A01JM
Vertical
aiming
Horizontal
aiming
If the vehicle has had front body
repair and the headlight assembly
has been replaced, the headlight aim-
ing should be checked using an aim-
ing screen as shown in the illustra-
tion. Turn on the headlight switch.
(Low Beam Position)
1. Adjust headlights so that main axis
of light is parallel to center line of
the body and is aligned with point
"P" shown in the illustration.
2. Dotted lines in the illustration show
the center of headlights.
G290B01JM-GAT
Adjustment After Headlight
Assembly Replacement
G290B01B
L
W
H
H
Cut-off line
Ground line
"P"
Horizontal line
Vertical line
Left-Hand Drive
30 mm
L
G290B01JM-D
W
H
H
Cut-off line
"P"
Vertical line
Horizontal line
Ground
line
Right-Hand Drive
30 mm

Related Topics

DO-IT-YOURSELF MAINTENANCE
ENGINE COMPARTMENT GENERAL CHECKS CHECKING THE ENGINE OIL CHANGING THE OIL AND FILTER CHECKING AND CHANGING THE ENGINE COOLANT CHANGING THE AIR CLEANER FILTER WINDSHIELD WIPER BLADES FILLING THE WASHER RESERVOIR CHECKING THE TRANSAXLE OIL (MANUAL) CHECKING THE TRANSAXLE FLUID (AUTOMATIC) CHECKING THE BRAKES CHECKING THE CLUTCH FLUID AIR CONDITIONING CARE CHANGING THE CLIMATE CONTROL AIR FILTER CHECKING THE FREEPLAY CHECKING BRAKE PEDAL CLEARANCE CHECKING DRIVE BELTS CHECKING AND REPLACING FUSES CHECKING THE BATTERY CHECKING ELECTRIC COOLING FANS POWER STEERING FLUID LEVEL REMOVAL OF WATER FROM THE FUEL FILTER REPLACEMENT OF LIGHT BULBS BULB WATTAGE FUSE PANEL DESCRIPTION

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot