Get Maintenance Guide for Hyundai Tucson SUV Third Generation (2016-2019)

Maintenance

Engine compartment .............................................7-3

Maintenance services ...........................................7-6

Owner's responsibility......................................................7-6

Owner maintenance precautions ..................................7-6

Owner maintenance...............................................7-7

Owner maintenance schedule........................................7-8

Scheduled maintenance services ......................7-10

Normal Maintenance Schedule

(For Europe, Except Russia).........................................7-11

Maintenance Under Severe Usage and Low Mileage

Conditions (For Europe, Except Russia)....................7-15

Normal Maintenance Schedule

Brake/clutch fluid................................................7-35

Checking the brake/clutch fluid level........................7-35

Washer fluid .........................................................7-36

Checking the washer fluid level..................................7-36

Parking brake .......................................................7-36

Checking the parking brake.........................................7-36

Fuel filter (for Diesel).........................................7-37

Draining water from fuel filter....................................7-37

Fuel filter cartridge replacement................................7-37

Air cleaner ............................................................7-38

Filter replacement...........................................................7-38

Climate control air filter .....................................7-40

Filter inspection...............................................................7-40

Filter replacement...........................................................7-40

(Except Europe, For Russia).........................................7-17

Maintenance Under Severe Usage and Low Mileage

Conditions (Except Europe, For Russia)....................7-21

Wiper blades.........................................................7-41

Blade inspection..............................................................7-41

Blade replacement..........................................................7-41

Explanation of scheduled maintenance items..7-24

Engine oil ..............................................................7-28

Checking the engine oil level (Gasoline engine).....7-28

Checking the engine oil level (Diesel engine) ........7-29

Checking the engine oil and filter..............................7-30

Engine coolant......................................................7-31

Checking the engine coolant level..............................7-31

Changing the engine coolant.......................................7-34

Battery...................................................................7-44

For best battery service................................................7-44

Battery capacity label....................................................7-46

Battery recharging .........................................................7-46

Reset items.......................................................................7-47

7

Tires and wheels..................................................7-48

Tire care............................................................................7-48

Recommended cold tire inflation pressures.............7-48

Checking tire inflation pressure..................................7-50

Tire rotation .....................................................................7-51

Wheel alignment and tire balance..............................7-52

Tire replacement .............................................................7-52

Wheel replacement ........................................................7-54

Tire traction......................................................................7-54

Tire maintenance ...........................................................7-54

Tire sidewall labeling......................................................7-54

Low aspect ratio tire......................................................7-59

Fuses......................................................................7-60

Fuse/Relay panel description......................................7-65

Light bulbs.............................................................7-75

Headlamp, static bending lamp, position lamp,

Appearance care..................................................7-93

Exterior care ....................................................................7-93

Interior care......................................................................7-99

Emission control system...................................7-100

Crankcase emission control system.........................7-100

Evaporative emission control system ......................7-100

Exhaust emission control system.............................7-101

turn signal lamp and fog lamp light bulb

replacement......................................................................7-76

Side repeater lamp replacement.................................7-81

Headlamp and front fog lamp aiming........................7-82

Rear combination light bulb replacement.................7-87

High mounted stop lamp replacement.......................7-90

License plate light bulb replacement.........................7-90

Interior light bulb replacement....................................7-91

7

ENGINE COMMPARTMENNT

■ Gasoline Engine (Gamma 1.6L GDI)

1.Engine coolant reservoir/Radiator cap

2.Brake/clutch fluid reservoir

3.Air cleaner

4.Engine oil dipstick

5.Engine oil filler cap

6.Windshield washer fluid reservoir

7.Fuse box

■ Gasoline Engine (Gamma 1.6L T-GDI)

8.Battery

The actual engine room in the vehicle

may differ from the illustration.

7

OTLE075001/OTLE075002

7-3

Maintenance

■ Gasoline Engine (Nu 2.0 MPI)

1. Engine coolant reservoir/Radiator cap

2. Brake/clutch fluid reservoir

3. Air cleaner

4. Engine oil dipstick

5. Engine oil filler cap

6. Windshield washer fluid reservoir

7. Fuse box

■ Gasoline Engine (Theta II 2.4 GDI)

8. Battery

The actual engine room in the vehicle

may differ from the illustration.

OTLE075003/OTLE075104

7-4

■ Diesel Engine (U2 1.7 TCI)

1. Engine coolant reservoir/Radiator cap

2. Brake/clutch fluid reservoir

3. Air cleaner

4. Engine oil dipstick

5. Engine oil filler cap

6. Windshield washer fluid reservoir

7. Fuse box

■ Diesel Engine (R 2.0 TCI)

8. Battery

9.Fuel filter

7

The actual engine room in the vehicle

may differ from the illustration.

OTL075002/OTL075001

7-5

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care Detailed warranty information is pro-

to prevent damage to your vehicle vided in your Service Passport.

and injury to yourself whenever per-

NOTICE

Improper owner maintenance dur-

ing the warranty period may affect

warranty coverage. For details, read

the separate Service Passport pro-

vided with the vehicle. If you're

unsure about any servicing or main-

tenance procedure, we recommend

that the system be serviced by an

authorized HYUNDAI dealer.

Repairs and adjustments required as

forming any maintenance or inspec-

a result of improper maintenance or

tion procedures.

a lack of required maintenance are

We recommend you have your vehi- not covered.

cle maintained and repaired by an

authorized HYUNDAI dealer. An

Owner maintenance precautions

authorized HYUNDAI dealer meets

HYUNDAI’s high service quality stan- Inadequate, incomplete or insufficient

dards and receives technical support servicing may result in operational

from HYUNDAI in order to provide problems with your vehicle that could

you with a high level of service satis- lead to vehicle damage, an accident,

faction.

or personal injury. This chapter pro-

vides instructions only for the mainte-

nance items that are easy to perform.

Owner’s responsibility

Several procedures can be done only

by an authorized HYUNDAI dealer

with special tools.

Maintenance service and record reten-

tion are the owner’s responsibility.

You should retain documents that show

proper maintenance has been per-

formed on your vehicle in accordance

with the scheduled maintenance serv-

ice charts shown on the following

pages. You need this information to

establish your compliance with the

servicing and maintenance require-

ments of your vehicle warranties.

Your vehicle should not be modified in

any way. Such modifications may

adversely affect the performance,

safety or durability of your vehicle and

may, in addition, violate conditions of

the limited warranties covering the

vehicle.

7-6

OWNER MAINNTENANCE

The following lists are vehicle checks

and inspections that should be per-

formed by the owner or an authorized

HYUNDAI dealer at the frequencies

indicated to help ensure safe, depend-

able operation of your vehicle.

(Continued)

WARNING

• Block the tires (front and back)

to prevent the vehicle from

moving.

Performing maintenance work

on a vehicle can be dangerous.

If you lack sufficient knowledge

and experience or the proper

tools and equipment to do the

work, we recommend that the

system be serviced by an author-

ized HYUNDAI dealer. ALWAYS

follow these precautions for

performing maintenance work:

Remove loose clothing or jew-

elry that can become entan-

gled in moving parts.

Any adverse conditions should be

brought to the attention of your dealer

as soon as possible.

• If you must run the engine

during maintenance, do so

out doors or in an area with

plenty of ventilation.

These Owner Maintenance vehicle

checks are generally not covered by

warranties and you may be charged

for labor, parts and lubricants used.

• Keep flames, sparks, or smok-

ing materials away from the

battery and fuel-related parts.

• Park your vehicle on level

ground, move the shift lever

into the P (Park, for automatic

transaxle/dual clutch transmis-

sion vehicle) position, apply the

parking brake, place the igni-

tion switch in the LOCK/OFF

position.

7

(Continued)

7-7

Maintenance

While operating your vehicle:

Owner maintenance schedule

WARNING

• Note any changes in the sound of

the exhaust or any smell of exhaust

fumes in the vehicle.

When you stop for fuel:

Diesel Engine

• Check the engine oil level.

• Check coolant level in the engine

coolant reservoir.

Never manipulate or modify the

injection system while running

the diesel engine or within 30

seconds after turning OFF the

diesel engine.The high-pressure

pump, high-pressure pipes, rail,

and injectors are still subject to

the high pressure right after

stopping the diesel engine.

• Check for vibrations in the steering

wheel. Notice if there is any

increased steering effort or loose-

ness in the steering wheel, or

change in its straight-ahead position.

• Check the windshield washer fluid

level.

• Check for low or under-inflated tires.

• Notice if your vehicle constantly turns

slightly or “pulls” to one side when

traveling on smooth, level road.

WARNING

Be careful when checking your

engine coolant level when the

engine is hot.This may result in

coolant being blown out of the

opening and cause serious

burns and other injuries.

• When stopping, listen and check for

unusual sounds, pulling to one side,

increased brake pedal travel or

“hard-to-push” brake pedal.

When the fuel leakage vents out,

it may cause serious body injury.

Any people, who are implement-

ed with the artificial cardiac

pacemaker, should remain away

from the ECU or the wiring har-

ness by at least 30 cm, while run-

ning the diesel engine. The high

currents of the electric engine

control system produce a con-

siderable amount of magnetic

fields.

• If any slipping or changes in the

operation of your transaxle occurs,

check the transaxle fluid level.

• Check the automatic transaxle/

dual clutch transmission P (Park)

function.

• Check the parking brake.

• Check for fluid leaks under your

vehicle (water dripping from the air

conditioning system during or after

use is normal).

7-8

At least monthly:

At least twice a year:

(i.e., every Spring and Fall)

At least once a year:

• Check coolant level in the engine

coolant reservoir.

• Clean body and door drain holes.

• Check radiator, heater and air condi-

tioning hoses for leaks or damage.

• Lubricate door hinges and hood

hinges.

• Check the operation of all exterior

lights, including the stoplights, turn

signals and hazard warning flashers.

• Check windshield washer spray

and wiper operation. Clean wiper

blades with clean cloth dampened

with washer fluid.

• Lubricate door and hood locks and

latches.

• Check the inflation pressures of all

tires including the spare for tires

that are worn, show uneven wear,

or are damaged.

• Lubricate door rubber weather

strips.

• Check headlamp alignment.

• Check the air conditioning system.

• Check muffler, exhaust pipes,

shields and clamps.

• Inspect and lubricate automatic

transaxle linkage and controls.

• Check for loose wheel lug nuts.

• Check the seat belts for wear and

function.

• Clean the battery and terminals.

• Check the brake fluid level.

7

7-9

Maintenance

SCHEDULEED MAINTEENANCE SSERVICES

Follow Normal Maintenance Schedule if the vehicle is usually operated where none of the following conditions apply.

If any of the following conditions apply, you must follow the Maintenance Under Severe Usage Conditions.

• Repeated driving short distance of less than 8 km (5 miles) in normal temperature or less than 16 km(10 miles) in

freezing temperature

• Extensive engine idling or low speed driving for long distances

• Driving on rough, dusty, muddy, unpaved, graveled or salt-spread roads

• Driving in areas using salt or other corrosive materials or in very cold weather

• Driving in the condition of inflowing sand or dust into engine

• Driving in heavy traffic area

• Driving on uphill, downhill, or mountain road repeatedly

• Towing a trailer or using a camper, or roof rack

• Driving as a patrol car, taxi, other commercial use of vehicle towing

• Driving over 170 km/h (106 mile/h)

• Frequently driving in stop-and-go condition

If your vehicle is operated under the above conditions, you should inspect, replace or refill more frequently than the

following Normal Maintenance Schedule. After the periods or distance shown in the chart, continue to follow the pre-

scribed maintenance intervals.

7-10

Normal Maintenance Schedule (For Europe, Except Russia)

MAINTENANCE

INTERVALS

Months

24

20

30

48

40

60

72

60

90

96

80

120

100

150

144

120

180

168

140

210

192

160

240

Miles x 1,000

Km x 1,000

MAINTENANCE

ITEM

120

First Inspect at 90,000 km (60,000 miles) or 72 months,

after every 30,000 km (20,000 miles) or 24 months

Drive belts (Gasoline) *¹

First Inspect at 90,000 km (60,000 miles) or 48 months,

after every 30,000 km (20,000 miles) or 24 months

Drive belts (Diesel) *¹

Diesel *²*³*⁴

R

Gasoline (1.6 GDI) *²*⁵

Gasoline (1.6 T-GDI) *²

Gasoline (2.0 MPI) *²

Engine oil and

engine oil filter **

Replace every 15,000 km (10,000 miles) or 12 months

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

** : The engine oil level should be checked regularly and maintained properly. Operating with an insufficient amount of oil can dam-

age the engine, and such damage is not covered by warranty.

*¹: Inspect drive belt tensioner, idler and alternator pulley and if necessary correct or replace.

*²: Check the engine oil level and leak every 500 km (350 miles) or before starting a long trip.

7

*³: This maintenance schedule depends on fuel quality. It is applicable only when using a qualified fuel <"EN590 or equivalent">.

If the diesel fuel specifications don't meet the EN590, it must be replaced according to the severe maintenance schedule.

*⁴: If the recommended oil is not available, replace engine oil and engine oil filter every 20,000 km or 12 months.

*⁵: If the recommended oil is not available, replace engine oil and engine oil filter every 15,000 km.

7-11

Maintenance

Normal Maintenance Schedule (For Europe, Except Russia) (Cont.)

MAINTENANCE

INTERVALS

Months

24

20

30

48

40

60

72

60

90

96

80

120

100

150

144

120

180

168

140

210

192

160

240

Miles x 1,000

Km x 1,000

MAINTENANCE

ITEM

120

Fuel additives (Gasoline) *⁷

Add every 15,000 km (10,000 miles) or 12 months

Intercooler, in/out hose,

air intake hose

Inspect every 10,000 km (6,500 miles)

1.6 T-GDI

Air cleaner filter

I

R

I

R

I

R

I

R

Replace every 75,000 km (50,000 miles) *⁸or 60 months

Replace every 160,000 km (100,000 miles) *⁸or 120 months

For 1.6 T-GDI

Spark plugs

Except 1.6 T-GDI

Vapor hose and fuel filler cap (Gasoline)

I

Fuel tank air filter (Gasoline)

Fuel filter (Gasoline) *⁹

I

Fuel lines, hoses and connections (Gasoline)

Fuel lines, hoses and connections (Diesel)

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁷: If good quality gasolines meet Europe Fuel standards (EN228) or equivalents including fuel additives is not available, one bot-

tle of additive is recommended. Additives are available from your authorized HYUNDAI dealer along with information on how to

use them. Do not mix other additives.

*⁸: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁹: The fuel filter is considered to be maintenance free but periodic inspection is recommended for this maintenance schedule

depends on fuel quality. If there are some important matters like fuel flow restriction, surging, loss of power, hard starting prob-

lem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for

details.

7-12

Normal Maintenance Schedule (For Europe, Except Russia) (Cont.)

MAINTENANCE

INTERVALS

Months

24

20

30

I

48

40

60

R

72

60

90

I

96

80

120

R

120

100

150

I

144

120

180

R

168

140

210

I

192

160

240

R

Miles x 1,000

Km x 1,000

MAINTENANCE

ITEM

Fuel filter cartridge (Diesel) *¹⁰

Inspect “Coolant level adjustment and leak” every day.

At first, inspect 60,000 km (40,000 miles) or 48 months

after that, inspect every 30,000 km (20,000 miles) or 24 months

Cooling system

At first, replace at 210,000 km (120,000 miles) or 10 years :

after that, replace every 30,000 km (20,000 miles) or 24 months *¹²

Engine coolant *¹¹

Battery condition

I

Brake lines, hoses and connections

Parking brake

I

Brake/clutch fluid

R

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

Disc brakes and pads

Steering gear rack, linkage and boots

I

7

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹⁰: This maintenance schedule depends on fuel quality. It is applicable only when using a qualified fuel <"EN590 or equivalent">.

If the diesel fuel specifications don't meet the EN590, it must be replaced more frequently. If there are some important safety

matters like fuel flow restriction, surging, loss of power, hard starting problem etc., replace the fuel filter immediately regard-

less of maintenance schedule. We recommend that you consult an authorized HYUNDAI dealer for details.

*¹¹: When adding coolant, use only deionized water or soft water for your vehicle and never mix hard water in the coolant filled at

the factory. An improper coolant mixture can result in serious malfunction or engine damage.

*¹²: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7-13

Maintenance

Normal Maintenance Schedule (For Europe, Except Russia) (Cont.)

MAINTENANCE

INTERVALS

Months

24

20

48

40

72

60

96

80

120

100

144

120

168

140

192

160

Miles x 1,000

Km x 1,000

MAINTENANCE

ITEM

30

60

90

120

150

180

210

240

Driveshaft and boots

I

Tire (pressure & tread wear)

Front suspension ball joints

Air conditioner refrigerant

Air conditioner compressor

Climate control air filter

Manual transaxle fluid *¹³

Dual clutch transmission fluid *¹³

Automatic transaxle fluid

Transfer case oil (4WD) *¹³

Rear differential oil (4WD) *¹³

Propeller shaft (4WD)

I

R

I

R

I

R

I

R

I

No check, No service required

I

Valve clearance (Gasoline 1.6) *¹⁴

Exhaust system

I

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹³: Manual transaxle/dual clutch transmission fluid, transfer case oil and differential oil should be changed anytime they have been

submerged in water.

*¹⁴: Inspect for excessive valve noise and/or engine vibration and adjust if necessary.We recommend that the system be checked

by an authorized HYUNDAI dealer.

7-14

Maintenance Under Severe Usage and Low Mileage Conditions (For Europe, Except Russia)

The following items must be serviced more frequently on cars mainly used under severe and low mileage driving con-

ditions. Refer to the chart below for the appropriate maintenance intervals.

R : Replace

I : Inspect and if necessary, adjust, correct, clean or replace

Maintenance

operation

Maintenance item

Maintenance intervals

Driving condition

Diesel

Replace every 15,000 km (10,000 miles)

or 12 months

Gasoline (1.6 GDI)

Engine oil and

engine oil filter

A, B, C, D, E, F, G,

H, I, K, L

Replace every 7,500 km (4,500 miles)

or 6 months

R

Gasoline (1.6 T-GDI)

Gasoline (2.0 MPI)

Replace every 7,500 km (4,500 miles)

or 6 months

Replace more frequently

depending on the condition

Air cleaner filter

Spark plugs

R

I

C, E

B, H

Replace more frequently

depending on the condition

Inspect more frequently

depending on the condition

Steering gear rack, linkage and boots

Front suspension ball joints

Disc brakes and pads, calipers and rotors

Parking brake

C, D, E, F, G

C, D, E, G, H

C, D, G, H

7

Inspect more frequently

depending on the condition

I

Inspect more frequently

depending on the condition

I

Inspect more frequently

depending on the condition

I

Inspect more frequently

depending on the condition

Driveshaft and boots

I

C, D, E, F, G, H, I

7-15

Maintenance

operation

Maintenance item

Maintenance intervals

Driving condition

Replace more frequently

depending on the condition

Climate control air filter

Manual transaxle fluid

R

I

C, E, G

C, D, E, F, G,

H, I, K

Every 120,000 km (80,000 miles)

Every 100,000 km (62,000 miles)

Every 120,000 km (80,000 miles)

A, C, D, E, F, G, H,

I, K

Automatic transaxle fluid

Dual clutch transmission fluid

Rear differential oil (4WD)

Transfer case oil (4WD)

Propeller shaft (4WD)

C, D, E, G, H,

I, K

C, D, E, G, I, K, H

C, E

Every 20,000 km (12,500 miles)

or 12 months

Severe driving conditions

A : Repeatedly driving short distance of less than 5 miles (8 km)

in normal temperature or less than 10 miles (16 km) in freez-

ing temperature

E : Driving in the condition of inflowing sand or dust into engine

F : Driving in heavy traffic area

G : Driving on uphill, downhill, or mountain roads repeatedly

H : Towing a trailer, or using a camper or roof rack

I : Driving for patrol car, taxi, commercial car or vehicle towing

J : Driving over 140 km/h (87 mile/h)

B : Extensive engine idling or low speed driving for long dis-

tances

C : Driving on rough, dusty, muddy, unpaved, graveled or salt

spread roads

K : Driving over 170 km/h (106 mile/h)

D : Driving in areas using salt or other corrosive materials or in

very cold weather

L : Frequently driving in stop-and-go conditions and under

15,000 km per year.

7-16

Normal Maintenance Schedule (Except Europe, For Russia)

MAINTENANCE

INTERVALS

Months

12

10

15

I

24

20

30

I

36

30

45

I

48

40

60

I

60

50

75

I

72

60

90

I

84

70

105

I

96

80

120

I

Miles x 1,000

Km x 1,000

Gasoline

MAINTENANCE

ITEM

Drive belts *¹

At first, inspect at 90,000 km (60,000 miles) or 48 months

Diesel

after that, inspect every 30,000 km (20,000 miles) or 24 months

Replace every 15,000 km (10,000 miles) or 12 months

Replace every 10,000 km (6,500 miles) or 12 months

Diesel *²- For Russia

Diesel *²- Except Russia

Gasoline (1.6 GDI, 2.0 MPI,

2.4 GDI) - Except Middle

East, Morocco, Egypt *²

R

Engine oil and

engine oil filter *³

Gasoline (1.6 GDI, 2.0 MPI,

2.4 GDI) - For Middle East,

Morocco, Egypt *²

Replace every 10,000 km (6,500 miles) or 12 months

Gasoline (1.6 T-GDI)

- For South Africa *²

R

7

Gasoline (1.6 T-GDI)

- Except South Africa *²

Replace every 10,000 km (6,500 miles) or 6 months

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: Inspect drive belt tensioner, idler and alternator pulley and if necessary correct or replace.

*²: Check the engine oil level and leak every 500 km (350 miles) or before starting a long trip.

*³: The engine oil level should be checked regularly and maintained properly. Operating with an insufficient amount of oil can dam-

age the engine, and such damage is not covered by warranty.

7-17

Maintenance

Normal Maintenance Schedule (Except Europe, For Russia) (Cont.)

MAINTENANCE

INTERVALS

Months

12

10

15

24

20

30

36

30

45

48

40

60

50

75

72

60

90

84

70

96

80

Miles x 1,000

Km x 1,000

MAINTENANCE

ITEM

105

120

Fuel additives (Gasoline) *⁴

Add every 10,000 km (6,500 miles) or 6 months

Intercooler, in/out hose,

air intake hose

1.6 T-GDI

Inspect every 10,000 km (6,500 miles)

Except Middle East

For Middle East

For 1.6 T-GDI

I

R

I

R

I

Air cleaner filter

Spark plugs

R

Replace every 75,000 km (50,000 miles) *⁵or 60 months

Replace every 160,000 km (100,000 miles) *⁵or 120 months

Except 1.6 T-GDI

Vapor hose and fuel filler cap (Gasoline)

I

R

I

Fuel tank air filter (Gasoline)

Fuel filter (Gasoline) *⁶

I

R

I

Fuel lines, hoses and connections (Gasoline)

Fuel lines, hoses and connections (Diesel)

I

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁴: If good quality gasolines meet Europe Fuel standards (EN228) or equivalents including fuel additives is not available, one bot-

tle of additive is recommended. Additives are available from your authorized HYUNDAI dealer along with information on how

to use them. Do not mix other additives.

*⁵: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁶: The fuel filter is considered to be maintenance free but periodic inspection is recommended for this maintenance schedule

depends on fuel quality. If there are some important matters like fuel flow restriction, surging, loss of power, hard starting prob-

lem etc, replace the fuel filter immediately regardless of maintenance schedule. We recommend that you consult an authorized

HYUNDAI dealer for details.

7-18

Normal Maintenance Schedule (Except Europe, For Russia) (Cont.)

MAINTENANCE

INTERVALS

Months

12

10

15

24

20

30

I

36

30

45

48

40

60

R

60

50

75

72

60

90

I

84

70

96

80

120

R

Miles x 1,000

Km x 1,000

MAINTENANCE

ITEM

105

Fuel filter cartridge (Diesel) *⁷

Inspect “Coolant level adjustment and leak” every day.

At first, inspect 60,000 km (40,000 miles) or 48 months

after that, inspect every 30,000 km (20,000 miles) or 24 months

Cooling system

At first, replace at 200,000 km (120,000 miles) or 120 months :

after that, replace every 40,000 km (25,000 miles) or 24 months *⁵

Engine coolant *⁸

Battery condition

I

Brake lines, hoses and connections

Parking brake

Brake/clutch fluid

Disc brakes and pads

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁵: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7

*⁷: This maintenance schedule depends on fuel quality. It is applicable only when using a qualified fuel <"EN590 or equivalent">.

If the diesel fuel specifications don't meet the EN590, it must be replaced more frequently. HYUNDAI recommends "every

7,500km inspection, every 15,000km replacement". If there are some important safety matters like fuel flow restriction, surg-

ing, loss of power, hard starting problem etc., replace the fuel filter immediately regardless of maintenance schedule. We rec-

ommend that you consult an authorized HYUNDAI dealer for details.

*⁸: When adding coolant, use only deionized water or soft water for your vehicle and never mix hard water in the coolant filled at

the factory. An improper coolant mixture can result in serious malfunction or engine damage. For your convenience, it can be

replaced prior to it's interval when you do maintenance of other items.

7-19

Maintenance

Normal Maintenance Schedule (Except Europe, For Russia) (Cont.)

MAINTENANCE

INTERVALS

Months

12

10

15

I

24

36

30

45

I

48

60

50

75

I

72

84

70

105

I

96

Miles x 1,000

Km x 1,000

20

40

60

80

MAINTENANCE

ITEM

30

60

90

120

Steering gear rack, linkage and boots

Driveshaft and boots

I

Tire (pressure & tread wear)

Front suspension ball joints

Air conditioner refrigerant

I

Air conditioner compressor

I

Climate control air filter

Manual transaxle fluid *⁹

R

I

R

I

Dual clutch transmission fluid *⁹

I

Automatic transaxle fluid

No check, No service required

Transfer case oil (4WD) *⁹

Rear differential oil (4WD) *⁹

Propeller shaft (4WD)

I

Valve clearance (Gasoline) *¹⁰

Exhaust system

I

ERA-GLONASS system (for Russia)

ERA-GLONASS system battery (for Russia, if equipped)

I

Replace every 3 years

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁹: Manual transaxle/Dual clutch transmission fluid, transfer case oil and differential oil should be changed anytime they have been

submerged in water.

*¹⁰: Inspect for excessive valve noise and/or engine vibration and adjust if necessary.We recommend that the system be checked

by an authorized HYUNDAI dealer.

7-20

Maintenance Under Severe Usage and Low Mileage Conditions (Except Europe, For Russia)

The following items must be serviced more frequently on cars mainly used under severe driving conditions.

Refer to the chart below for the appropriate maintenance intervals.

R : Replace

I : Inspect and if necessary, adjust, correct, clean or replace

Maintenance

operation

Driving

condition

Maintenance item

Maintenance intervals

Diesel

- For Russia

7,500 km (4,500 miles) or 6 months

5,000 km (3,000 miles) or 6 months

Diesel

- Except Russia

Gasoline (1.6 GDI, 2.0 MPI,

2.4 GDI) - Except Middle

East, Morocco, Egypt

7,500 km (4,500 miles) or 6 months

5,000 km (3,000 miles) or 6 months

Engine oil and

engine oil filter

A, B, C, D, E, F, G,

H, I, K, L

R

Gasoline (1.6 GDI, 2.0 MPI,

2.4 GDI) - For Middle East,

Morocco, Egypt

Gasoline (1.6 T-GDI)

- For South Africa

7,500 km (4,500 miles) or 6 months

5,000 km (3,000 miles) or 6 months

7

Gasoline (1.6 T-GDI)

- Except South Africa

Replace more frequently

depending on the condition

Air cleaner filter

R

I

C, E

B, H

Replace more frequently

depending on the condition

Spark plugs

Inspect more frequently

depending on the condition

Steering gear rack, linkage and boots

C, D, E, F, G

7-21

Maintenance

operation

Driving

condition

Maintenance item

Maintenance intervals

Inspect more frequently

depending on the condition

Front suspension ball joints

Disc brakes and pads, calipers and rotors

Parking brake

I

C, D, E, F, G

C, D, E, G, H

C, D, G, H

Inspect more frequently

depending on the condition

Inspect more frequently

depending on the condition

I

Inspect more frequently

depending on the condition

Driveshaft and boots

I

C, D, E, F, G, H, I, K

C, E, G

Replace more frequently

depending on the condition

Climate control air filter

R

I

C, D, E, F, G,

H, I, K

Manual transaxle fluid

Every 120,000 km (80,000 miles)

Every 100,000 km (62,000 miles)

Every 120,000 km (80,000 miles)

Automatic transaxle fluid

Dual clutch transmission fluid

Rear differential oil (4WD)

Transfer case oil (4WD)

Propeller shaft (4WD)

A, C, F, G, H, I, K

C, D, E, G, H, I, K

C, D, E, G, I, K, H

C, E

Every 15,000 km (10,000 miles)

or 12 months

Every 7,500 km (4,650 miles)

or 6 months

ERA-GLONASS system (for Russia)

I

A, L

7-22

Severe driving conditions

A : Repeatedly driving short distance of less than 5 miles (8 km)

in normal temperature or less than 10 miles (16 km) in freez-

ing temperature

E : Driving in the condition of inflowing sand or dust into engine

F : Driving in heavy traffic area

G : Driving on uphill, downhill, or mountain roads repeatedly

H : Towing a trailer, or using a camper or roof rack

I : Driving for patrol car, taxi, commercial car or vehicle towing

J : Driving over 140 km/h (87 mile/h)

B : Extensive engine idling or low speed driving for long distances

C : Driving on rough, dusty, muddy, unpaved, graveled or salt

spread roads

D : Driving in areas using salt or other corrosive materials or in

very cold weather

K : Driving over 170 km/h (106 mile/h)

L : Frequently driving in stop-and-go conditions

7

7-23

Maintenance

EXPLANATIOON OF SCHEDUULLED MAINTENNANCE ITEMS

Engine oil and filter

Fuel filter (cartridge)

WARNING

The engine oil and filter should be A clogged-up fuel filter may limit the

changed at the intervals specified in vehicle driving speed, damage the

the maintenance schedule. If the car emission system, and cause the

is being driven in severe conditions, hard starting. When a considerable

more frequent oil and filter changes amount of foreign substances are

Diesel Engine

Never manipulate or modify the

injection system while running

the diesel engine or within 30

seconds after turning OFF the

diesel engine. The high-pressure

pump, high-pressure pipes, rail,

and injectors are still subject to

the high pressure right after

stopping the diesel engine.When

the fuel leakage vents out, it may

cause serious body injury. Any

people, who are implemented

with the artificial cardiac pace-

maker, should remain away from

the ECU or the wiring harness by

at least 30 cm while running the

diesel engine. The high currents

of the common rail system pro-

duce a considerable amount of

magnetic fields.

are required.

accumulated in the fuel tank, the fuel

filter should be replaced.

Drive belts

Upon installing a new fuel filter, oper-

ate the diesel engine for several min-

utes, and check the connections for

any leakages. We recommend you to

have the fuel filter replaced by an

authorized HYUNDAI dealer.

Inspect all drive belts for evidence of

cuts, cracks, excessive wear or oil

saturation and replace if necessary.

Drive belts should be checked peri-

odically for proper tension and

adjusted as necessary.

Fuel lines, fuel hoses and con-

nections

CAUTION

Check the fuel lines, fuel hoses and

connections for leakage and dam-

age. We recommend that the fuel

lines, fuel hoses and connections be

replaced by an authorized HYUNDAI

dealer.

When you are inspecting the belt,

place the ignition switch to the

LOCK/OFF or ACC position.

7-24

Vapor hose and fuel filler cap

Vacuum crankcase ventilation

hoses (if equipped)

Air cleaner filter

The vapor hose and fuel filler cap

should be inspected at those inter-

vals specified in the maintenance

schedule. Make sure that a new

vapor hose or fuel filler cap is cor-

rectly replaced.

We recommend that the air cleaner

filter be replaced by an authorized

HYUNDAI dealer.

Inspect the surface of hoses for evi-

dence of heat and/or mechanical

damage. Hard and brittle rubber,

cracking, tears, cuts, abrasions, and

excessive swelling indicate deterio-

ration. Particular attention should be

Spark plugs

(For Gasoline Engine)

paid to examine those hose surfaces Make sure to install new spark plugs

nearest to high heat sources, such of the correct heat range.

as the exhaust manifold.

Inspect the hose routing to assure

that the hoses do not come in con-

WARNING

tact with any heat source, sharp

edges or moving component which

might cause heat damage or

Do not disconnect and inspect

spark plugs when the engine is

hot.You may burn yourself.

mechanical wear. Inspect all hose

connections, such as clamps and

couplings, to make sure they are

secure, and that no leaks are pres-

ent. Hoses should be replaced

Valve clearance

(For Gasoline Engine)

7

Inspect excessive valve noise and/or

immediately if there is any evidence

of deterioration or damage.

engine vibration and adjust if neces-

sary. We recommend that the system

be serviced by an authorized HYUNDAI

dealer.

7-25

Maintenance

Cooling system

Automatic transaxle fluid

Manual transaxle fluid

(if equipped)

Check the cooling system parts, Automatic transaxle fluid should not

such as radiator, coolant reservoir, be checked under normal usage

hoses and connections for leakage conditions.

and damage. Replace any damaged

parts.

Inspect the manual transaxle fluid

according to the maintenance sched-

ule.

We recommend that the automatic

transaxle fluid changed by an author-

ized HYUNDAI dealer according to

the maintenance schedule.

Dual clutch transmission fluid

(if equipped)

Engine coolant

The coolant should be changed at

the intervals specified in the mainte-

nance schedule.

Inspect the dual clutch transmission

fluid according to the maintenance

schedule.

i

Information

Automatic transaxle fluid color is basi-

cally red.

As the vehicle is driven, the automatic

transaxle fluid will begin to look darker.

It is normal condition and you should

not judge the need to replace the fluid

based upon the changed color.

NOTICE

The use of a non-specified fluid

could result in transaxle malfunc-

tion and failure.

Use only specified automatic

transaxle fluid.

(Refer to “Recommended lubri-

cants and capacities” in chapter 8.)

7-26

Brake hoses and lines

Brake pads, calipers and

rotors

Steering gear box, linkage &

boots/lower arm ball joint

Visually check for proper installation,

chafing, cracks, deterioration and

any leakage. Replace any deteriorat-

ed or damaged parts immediately.

Check the pads for excessive wear, With the vehicle stopped and engine

discs for run out and wear, and off, check for excessive free-play in

calipers for fluid leakage.

the steering wheel.

For more information on checking Check the linkage for bends or dam-

the pads or lining wear limit, refer to age. Check the dust boots and ball

Brake/Clutch fluid

(if equipped)

the HYUNDAI web site.

joints for deterioration, cracks, or

damage. Replace any damaged

parts.

(http://service.hyundai-motor.com)

Check brake fluid level in the brake

fluid reservoir. The level should be

between “MIN” and “MAX” marks on

the side of the reservoir. Use only

hydraulic brake fluid conforming to

DOT 3 or DOT 4 specification.

Suspension mounting bolts

Drive shafts and boots

Check the suspension connections

for looseness or damage. Retighten

to the specified torque.

Check the drive shafts, boots and

clamps for cracks, deterioration, or

damage. Replace any damaged

parts and, if necessary, repack the

grease.

Parking brake

Inspect the parking brake system

including the parking brake lever and

cables.

Air conditioning refrigerant/

compressor

7

Check the air conditioning lines and

connections for leakage and dam-

age.

7-27

Maintenance

ENGINE OIL

5. Pull the dipstick out again and

check the level. The level should

be between F (Full) and L (Low).

Checking the engine oil level (Gasoline engine)

■ 1.6 GDI

■ 1.6 T-GDI

6. If it is near or at L, add enough oil

to bring the level to F.

WARNING

Radiator hose

Be very careful not to touch the

radiator hose when checking or

adding the engine oil as it may

be hot enough to burn you.

OTLE075008

OTLE075007

■ 2.0 MPI

■ 2.4 GDI

NOTICE

• Do not overfill the engine oil.

It may damage the engine.

• Do not spill engine oil, when

adding or changing engine oil. If

you drop the engine oil on the

engine room, wipe it off immedi-

ately.

OTLE075009

ODM076059L

1. Be sure the vehicle is on level 3. Turn the engine off and wait for a

ground.

few minutes (about 5 minutes) for

the oil to return to the oil pan.

2. Start the engine and allow it to reach

normal operating temperature.

• When you wipe the oil level gauge,

you should wipe it with a clean

cloth. When mixed with debris, it

can cause engine damage.

4. Pull the dipstick out, wipe it clean,

and re-insert it fully.

7-28

■ 1.6 GDI

■ 1.6 T-GDI

Checking the engine oil level

(Diesel engine)

■ 1.7 TCI

OTLE075005

OTLE075006

■ 2.0 MPI

■ 2.4 GDI

OTL075004

■ 2.0 TCI

7

OTLE075004

ODM076060L

Use only the specified engine oil.

(Refer to “Recommended lubricants and capacities” in chapter 8.)

OTL075003

1. Be sure the vehicle is on level

ground.

2. Start the engine and allow it to reach

normal operating temperature.

7-29

Maintenance

■ 1.7 TCI

3. Turn the engine off and wait for a

few minutes (about 5 minutes) for

the oil to return to the oil pan.

Checking the engine oil and filter

4. Pull the dipstick out, wipe it clean,

and re-insert it fully.

5. Pull the dipstick out again and

check the level. The level should

be between F (Full) and L (Low).

6. If it is near or at L, add enough oil

to bring the level to F.

OTL075006

■ 2.0 TCI

WARNING

Radiator hose

We recommend that the engine oil

and filter be replaced by an author-

ized HYUNDAI dealer.

Be very careful not to touch the

radiator hose when checking or

adding the engine oil as it may

be hot enough to burn you.

WARNING

Used engine oil may cause irri-

tation or cancer of the skin if

left in contact with the skin for

prolonged periods of time. Used

engine oil contains chemicals

that have caused cancer in lab-

oratory animals. Always protect

your skin by washing your

hands thoroughly with soap

and warm water as soon as pos-

sible after handling used oil.

NOTICE

OTL075005

Use only the specified engine oil.

(Refer to“Recommended lubricants

and capacities” in chapter 8.)

• Do not spill engine oil, when

adding or changing engine oil. If

you drop the engine oil on the

engine room, wipe it off immedi-

ately.

• When you wipe the oil level gauge,

you should wipe it with a clean

cloth. When mixed with debris, it

can cause engine damage.

7-30

ENGINE CCOOLANT

The high-pressure cooling system

has a reservoir filled with year-round

antifreeze coolant. The reservoir is

filled at the factory.

The coolant level should be filled

between MAX and MIN marks on the

side of the coolant reservoir when

the engine is cool.

Checking the engine coolant

level

Check the antifreeze protection and

coolant concentration level at least

once a year, at the beginning of the

winter season, and before traveling

to a colder climate.

If the coolant level is low, add enough

distilled (deionized) or soft water.

Bring the level to MAX, but do not

overfill.

If frequent additions are required, we

recommend that the system be

inspected by an authorized HYUNDAI

dealer.

NOTICE

• When the engine overheats from

low engine coolant, suddenly

adding engine coolant may cause

cracks in the engine. To prevent

damage, add engine coolant

slowly in small quantities.

OTL075070

• Do not drive with no engine

coolant. It may cause water pump

failure and engine seizure, etc.

7

OTL075008

Check the condition and connections

of all cooling system hoses and

heater hoses. Replace any swollen

or deteriorated hoses.

7-31

Maintenance

(Continued)

WARNING

• Turn the engine off and wait

until it cools down. Use

extreme care when removing

the radiator cap. Wrap a thick

towel around it, and turn it

counterclockwise slowly to

the first stop. Step back while

the pressure is released from

the cooling system.

Removing radiator

cap

The electric motor

(cooling fan) is con-

trolled by engine

coolant temperature,

refrigerant pressure

and vehicle speed. It may some-

times operate even when the

engine is not running. Use

extreme caution when working

near the blades of the cooling

fan so that you are not injured

by a rotating fan blades. As the

engine coolant temperature

decreases, the electric motor

will automatically shut off. This

is a normal condition.

• Never attempt to remove the

radiator cap while the engine

is operating or hot. Doing so

might lead to cooling system

and engine damage and could

result in serious personal

injury from escaping hot

coolant or steam.

When you are sure all the

pressure has been released,

press down on the cap, using

a thick towel, and continue

turning counterclockwise to

remove it.

(Continued)

• Even if the engine is not oper-

ating, do not remove the radia-

tor cap or the drain plug while

the engine and radiator are

hot. Hot coolant and steam

may still blow out under pres-

sure, causing serious injury.

The electric motor (cooling fan)

may operate until you discon-

nect the negative battery cable.

7-32

(Continued)

Recommended engine coolant

NOTICE

• When adding coolant, use only

deionized water or soft water for

your vehicle and never mix hard

water in the coolant filled at the fac-

tory. An improper coolant mixture

can result in serious malfunction or

engine damage.

■ Engine room rear view

Make sure the coolant cap is prop-

erly closed after refill of coolant.

Otherwise the engine could be over-

heated while driving.

■ Engine room front view

• The engine in your vehicle has alu-

minum engine parts and must be

protected by an ethylene-glycol-

based coolant to prevent corrosion

and freezing.

OTLE075010

• DO NOT USE alcohol or methanol

coolant or mix them with the spec-

ified coolant.

2. Make sure that the tiny protru-

sions inside the coolant cap

should be securely interlocked.

• Do not use a solution that contains

more than 60% antifreeze or less

than 35% antifreeze, which would

reduce the effectiveness of the solu-

tion.

OTL075062

1. Check if the radiator cap label is

straight In front.

7

(Continued)

7-33

Maintenance

For mixture percentage, refer to the

following table.

Changing the engine coolant

We recommend that the coolant be

replaced by an authorized HYUNDAI

dealer.

Mixture Percentage

(volume)

Ambient

Temperature

Antifreeze

Water

65

NOTICE

-15°C (5°F)

-25°C (-13°F)

-35°C (-31°F)

-45°C (-49°F)

35

40

50

60

Put a thick cloth or fabric around

the radiator cap before refilling

the coolant in order to prevent the

coolant from overflowing into engine

parts such as generator.

50

40

i

Information

If in doubt about the mix ratio, a 50%

water and 50% antifreeze mix is the

easiest to mix together as it will be the

same quantity of each. It is suitable to

use for most temperature ranges of

-35°C (-31°F) and higher.

WARNING

• Do not use engine coolant or

antifreeze in the washer fluid

reservoir.

• Engine coolant can severely

obscure visibility when sprayed

on the windshield and may

cause loss of vehicle control or

damage to paint and body trim.

7-34

BRAKE/CCLUTCH FLLUID (IFF EQUIPPEDD)

If the fluid level is excessively low,

Checking the brake/clutch

fluid level

WARNING

we recommend that the system be

checked by an authorized HYUNDAI

dealer.

When changing and adding brake/

clutch fluid, handle it carefully. Do

not let it come in contact with your

eyes. If brake/ clutch fluid should

come in contact with your eyes,

immediately flush them with a

large quantity of fresh tap water.

Have your eyes examined by a

doctor as soon as possible.

i

Information

Use only the specified brake/clutch

fluid. (Refer to “Recommended lubri-

cants and capacities” in chapter 8.)

WARNING

In the event the brake/clutch sys-

tem requires frequent additions of

fluid, we recommend that the sys-

tem be inspected by an author-

ized HYUNDAI dealer.

NOTICE

OTL075009

Do not allow brake/clutch fluid to

contact the vehicle's body paint, as

paint damage will result.

Check the fluid level in the reservoir

periodically. The fluid level should be

between MAX and MIN marks on the

side of the reservoir.

Brake/clutch fluid, which has been

exposed to open air for an extend-

ed time should never be used as its

quality cannot be guaranteed. It

should be disposed of properly.

Don't put in the wrong kind of fluid.

i

Information

Before removing the reservoir cap

and adding brake/clutch fluid, clean

the area around the reservoir cap

thoroughly to prevent brake/clutch

fluid contamination.

7

Before removing the brake/clutch filler

cap, read the warning on the cap.

i

Information

A few drops of mineral-based oil,

such as engine oil, in your brake/

clutch system can damage brake/

clutch system parts.

If the level is low, add fluid to the MAX

level.The level will fall with accumulat-

ed mileage. This is a normal condition

associated with the wear of the brake

linings.

Clean filler cap before removing. Use

only DOT3 or DOT4 brake/clutch fluid

from a sealed container.

7-35

Maintenance

WASHER FLUID

PARKING BRAKE

Checking the washer fluid

level

Checking the parking brake

NOTICE

Do not use engine coolant or

antifreeze in the washer fluid

reservoir.

WARNING

• Engine coolant can severely

obscure visibility when sprayed

on the windshield and may

cause loss of vehicle control or

damage to paint and body trim.

OTL055011

• Windshield Washer fluid agents

contain some amounts of alco-

hol and can be flammable under

certain circumstances. Do not

allow sparks or flame to contact

the washer fluid or the washer

fluid reservoir. Damage to the

vehicle or occupants could

occur.

OTL075010

Check the stroke of the parking

brake by counting the number of

“clicks’’ heard while fully applying it

from the released position. Also, the

parking brake alone should securely

hold the vehicle on a fairly steep

grade. If the stroke is more or less

than specified, we recommend that

the system be serviced by an author-

ized HYUNDAI dealer.

The reservoir is translucent so that

you can check the level with a quick

visual inspection.

Check the fluid level in the washer

fluid reservoir and add fluid if neces-

sary.

Plain water may be used if washer

fluid is not available.

• Windshield washer fluid is poi-

sonous to humans and animals.

Do not drink and avoid contact-

ing windshield washer fluid.

Serious injury or death could

occur.

However, use washer solvent with

antifreeze characteristics in cold cli-

mates to prevent freezing.

Stroke : 5~6 “clicks’’ at a force of

20 kg (44 lbs, 196 N).

7-36

FUEL FILTERR (FOR DIESEL)

Draining water from fuel filter

Fuel filter cartridge replace-

ment

The fuel filter in the diesel engine

operates the critical function of sepa-

rating water from the fuels and accu-

mulating the water in its bottom.

When enough water is accumulated

inside the fuel filter, the warning light

illuminates with the ignition switch in

the ON position.

In this case, we recommend you to

have the system checked by an

authorized HYUNDAI dealer.

OTL075014

NOTICE

When the accumulated water is not

drained at a proper timing, water

may permeate in the fuel filter,

damaging the major vehicle com-

ponents, such as the fuel system.

i

Information

When replacing the fuel filter car-

tridge, we recommend that you use

parts for replacement from an author-

ized HYUNDAI dealer.

7

7-37

Maintenance

AIR CLEANER

Filter replacement

OTL075015

OTL075016

1.Pull down the air cleaner filter cover. 3. Pull down the lever to the UNLOCK

position.

OTL075013

2. Wipe the inside of the air cleaner.

The air cleaner filter can be cleaned

for inspection using compressed air.

Do not attempt to wash or to rinse it,

as water will damage the filter.

If soiled, the air cleaner filter must be

replaced.

7-38

i

Information

If the vehicle is operated in extremely

dusty or sandy areas, replace the element

more often than the usual recommended

intervals (refer to “Maintenance Under

Severe Usage Conditions” in this chap-

ter).

NOTICE

• Do not drive with the air cleaner

filter removed. This will result in

excessive engine wear.

OTL075017

OTL075018

4. Replace the air cleaner filter.

5. Pull up the lever (1) to the LOCK

position.

• When removing the air cleaner

filter, be careful that dust or dirt

does not enter the air intake, or

damage may result.

6. Rise up the cover (2) until the hooks

on the cover are securely fastened

into the latches (3).

7. Check if the cover is firmly installed.

• Use HYUNDAI genuine parts,

use of non-genuine parts could

damage the air flow sensor.

7

7-39

Maintenance

CLIMATTE CONTRROL AIR FILTER

Filter inspection

Filter replacement

If the vehicle is operated in the

severely air-polluted cities or on

dusty rough roads for a long period,

it should be inspected more fre-

quently and replaced earlier. When

you, the owner, replace the climate

control air filter, replace it performing

the following procedure, and be care-

ful to avoid damaging other compo-

nents.

OTLE075011

OTL075019

Replace the filter according to the

Maintenance Schedule.

NOTICE

Install a new climate control air filter

in the correct direction with the

arrow symbol(↓) facing downwards.

Otherwise, the climate control effects

may decrease, possibly with a noise.

OTLE075012

3.Remove the climate control air filter

case while pressing the lock on the

right side of the cover.

OTL075020

1.With the glove box open, remove

the stoppers on both sides.

4.Replace the climate control air filter.

2.Remove the support strap (1).

5.Reassemble in the reverse order of

disassembly.

7-40

WIPER BLADES

Contamination of either the wind-

shield or the wiper blades with for-

eign matter can reduce the effective-

ness of the windshield wipers.

Blade inspection

Blade replacement

When the wipers no longer clean

adequately, the blades may be worn

or cracked, and require replacement.

Common sources of contamination

are insects, tree sap, and hot wax

treatments used by some commer-

cial car washes. If the blades are not

wiping properly, clean both the win-

dow and the blades with a good

cleaner or mild detergent, and rinse

thoroughly with clean water.

NOTICE

To prevent damage to the wiper arms

or other components, do not attempt

to move the wipers manually.

NOTICE

OLMB073019

The use of a non-specified wiper

blade could result in wiper mal-

function and failure.

NOTICE

i

Information

To prevent damage to the wiper

blades, do not use gasoline,

kerosene, paint thinner, or other

solvents on or near them.

Commercial hot waxes applied by

automatic car washes have been

known to make the windshield diffi-

cult to clean.

CAUTION

Do not allow the wiper arm to fall

against the windshield, since it

may chip or crack the windshield.

7

i

Information

Wiper blades are consumable item and

normal wear of the wipers may not be

covered by your vehicle warranty.

7-41

Maintenance

Front windshield wiper blade

OLF074018

OLF074019

2. Lift up the wiper blade clip. Then 3. Install the new blade assembly in

pull down the blade assembly and

remove it.

OLF074017

the reverse order of removal.

1. Raise the wiper arm.

4. Return the wiper arm on the wind-

shield.

7-42

Rear window wiper blade

OTL075051

2. Install the new blade assembly by

inserting the center part into the

slot in the wiper arm until it clicks

into place.

OTL075050

1. Raise the wiper arm and pull out

the wiper blade assembly.

3. Make sure the blade assembly is

installed firmly by trying to pull it

slightly.

To prevent damage to the wiper arms

or other components, we recommend

that the wiper blade be replaced by an

authorized HYUNDAI dealer.

7

7-43

Maintenance

BATTERY

For best battery service

i

Information

WARNING

The battery, which is originally

installed in your vehicle, is mainte-

nance free. However, your vehicle is

equipped with a battery marked with

LOWER and UPPER on the side, you

should check the electrolyte level. The

electrolyte level should be between the

LOWER and the UPPER. When the

electrolyte level is low, add distilled

(or de-mineralized) water. (Never add

sulfuric acids or other electrolyte). Be

careful not to spill distilled (or de-min-

eralized) water over the battery sur-

face or other adjacent components.

Also, do not overfill the battery cells.

If not, it may corrode the battery or

other components. Finally, securely

close the cell cap. However, we recom-

mend you to contact an authorized

HYUNDAI dealer for better battery

service.

To prevent SERIOUS INJURY or

DEATH to you or bystanders,

always follow these precautions

when working near or handling

the battery:

Always read and follow

instructions carefully

when handling a battery.

Wear eye protection

designed to protect the

eyes from acid splashes.

OTL075022

• Keep the battery securely mounted.

• Keep the battery top clean and dry.

Keep all flames, sparks,

or smoking materials

away from the battery.

• Keep the terminals and connec-

tions clean, tight, and coated with

petroleum jelly or terminal grease.

Hydrogen is always

present in battery cells,

is highly combustible,

and may explode if ignit-

ed.

• Rinse any spilled electrolyte from

the battery immediately with a

solution of water and baking soda.

Keep batteries out of

reach of children.

• If the vehicle is not going to be

used for an extended time, discon-

nect the battery cables.

(Continued)

7-44

i

Information

(Continued)

Batteries contain sulfu-

(Continued)

• NEVER attempt to recharge

the battery when the vehicle’s

battery cables are connected

to the battery.

An inappropriately disposed

ric acid which is highly

corrosive. Do not allow

acid to contact your

eyes, skin or clothing.

battery can be harmful to the

environment and human health.

Dispose the battery according to

your local law(s) or regulations.

Pb

• The electrical ignition system

works with high voltage.

NEVER touch these compo-

nents with the engine running

or when the Engine Start/Stop

button is in the ON position.

If acid gets into your eyes, flush

your eyes with clean water for at

least 15 minutes and get imme-

diate medical attention. If acid

gets on your skin, thoroughly

wash the area. If you feel pain or

a burning sensation, get med-

ical attention immediately.

NOTICE

If you connect unauthorized elec-

tronic devices to the battery, the

battery may be discharged. Never

use unauthorized devices.

• Do not allow the (+) and (-)

jumper cables to touch. It may

cause sparks.

• When lifting a plastic-cased

battery, excessive pressure

on the case may cause battery

acid to leak. Lift with a battery

carrier or with your hands on

opposite corners.

• The battery may rupture or

explode when you jump start

with a low or frozen battery.

7

• Do not attempt to jump start

your vehicle if your battery is

frozen.

(Continued)

7-45

Maintenance

Battery capacity label

Battery recharging

CAUTION

Your vehicle has a maintenance-free,

calcium-based battery.

■ Example

AGM battery (if equipped)

• If the battery becomes discharged

in a short time (because, for exam-

ple, the headlights or interior lights

were left on while the vehicle was

not in use), recharge it by slow

charging (trickle) for 10 hours.

• Absorbent Glass Matt (AGM)

batteries are maintenance-

free and we recommend that

the AGM battery be serviced

by an authorized HYUNDAI

dealer. For charging your

AGM battery, use only fully

automatic battery chargers

that are specially developed

for AGM batteries.

• If the battery gradually discharges

because of high electric load while

the vehicle is being used, recharge

it at 20-30A for two hours.

OLMB073072

The actual battery label in the vehicle

may differ from the illustration.

• When replacing the AGM bat-

tery, we recommend that you

use parts for replacement

from an authorized HYUNDAI

dealer.

1. CMF60L-BCI : The HYUNDAI

model name of battery

2. 12V : The nominal voltage

• Do not open or remove the

cap on top of the battery. This

may cause leaks of internal

electrolyte that could result in

severe injury.

3. 60Ah(20HR) : The nominal capacity

(in Ampere hours)

4. 92RC : The nominal reserve capac-

ity (in min.)

5. 550CCA : The cold-test current in

amperes by SAE

6. 440A : The cold-test current in

amperes by EN

7-46

Reset items

(Continued)

WARNING

Items should be reset after the bat-

tery has been discharged or the bat-

tery has been disconnected.

• The negative battery cable

must be removed first and

installed last when the battery

is disconnected.

When recharging the battery,

observe the following precau-

tions:

• Auto up/down window

(See chapter 3)

• Before performing maintenance

or recharging the battery, turn

off all accessories and stop the

engine.

• Disconnect the battery charger

in the following order.

• Sunroof (See chapter 3)

• Trip computer (See chapter 3)

1. Turn off the battery charger

main switch.

• Climate control system

(See chapter 3)

• Do not allow cigarettes, sparks,

or flame near the battery.

2. Unhook the negative clamp

from the negative battery

terminal.

• Wear eye protection when

checking the battery during

charging.

3. Unhook the positive clamp

from the positive battery

terminal.

• The battery must be removed

from the vehicle and placed in

an area with good ventilation.

• Watch the battery during

charging, and stop or reduce

the charging rate if the battery

cells begin gassing (boiling)

violently or if the temperature

of the electrolyte of any cell

exceeds 49°C (120°F).

7

(Continued)

7-47

Maintenance

TIRES ANDD WHEELS

Tire care

WARNING

For proper maintenance, safety, and

maximum fuel economy, you must

always maintain recommended tire

inflation pressures and stay within

the load limits and weight distribution

recommended for your vehicle.

Tire underinflation

Severe underinflation (70 kPa

(10 psi) or more) can lead to

severe heat build-up, causing

blowouts, tread separation and

other tire failures that can result

in the loss of vehicle control

leading to severe injury or

death. This risk is much higher

on hot days and when driving

for long periods at high speeds.

Recommended cold tire infla-

tion pressures

OTLE085006

All tire pressures (including the

spare) should be checked when the

tires are cold. “Cold Tires” means the

vehicle has not been driven for at

least three hours or driven less than

1.6 km (1 mile).

All specifications (sizes and pres-

sures) can be found on a label

attached to the vehicle.

Recommended pressures must be

maintained for the best ride, top vehi-

cle handling, and minimum tire wear.

For recommended inflation pres-

sure refer to “Tire and wheels” in

chapter 8.

7-48

CAUTION

Tire pressure

• Underinflation also results in

excessive wear, poor handling

and reduced fuel economy.

Wheel deformation also is

possible. Keep your tire pres-

sures at the proper levels. If a

tire frequently needs refilling,

we recommend that the tire be

checked by an authorized

HYUNDAI dealer.

• Warm tires normally exceed

recommended cold tire pres-

sures by 28 to 41 kPa (4 to 6

psi). Do not release air from

warm tires to adjust the pres-

sure or the tires will be under-

inflated.

Always observe the following:

• Check tire pressure when the

tires are cold. (After vehicle

has been parked for at least

three hours or hasn't been driv-

en more than 1.6 km (1 mile)

since startup.)

• Be sure to reinstall the tire

inflation valve caps. Without

the valve cap, dirt or moisture

could get into the valve core

and cause air leakage. If a

valve cap is missing, install a

new one as soon as possible.

• Check the pressure of your

spare tire each time you check

the pressure of other tires.

• Overinflation produces a harsh

ride, excessive wear at the cen-

ter of the tire tread, and a

greater possibility of damage

from road hazards.

• Never overload your vehicle.

Be careful not to overload a

vehicle luggage rack if your

vehicle is equipped with one.

WARNING

• Worn, old tires can cause acci-

dents. If your tread is badly

worn, or if your tires have been

damaged, replace them.

7

Tire inflation

Overinflation or underinflation

can reduce tire life, adversely

affect vehicle handling, and

lead to sudden tire failure. This

could result in loss of vehicle

control and potential injury.

7-49

Maintenance

Remove the valve cap from the tire

valve stem. Press the tire gage firmly

onto the valve to get a pressure

measurement. If the cold tire inflation

pressure matches the recommended

pressure on the tire and loading infor-

mation label, no further adjustment is

necessary. If the pressure is low, add

air until you reach the recommended

amount.

Checking tire inflation pres-

sure

WARNING

Check your tires once a month or

more.

• Inspect your tires frequently

for proper inflation as well as

wear and damage. Always use

a tire pressure gauge.

Also, check the tire pressure of the

spare tire.

• Tires with too much or too little

pressure wear unevenly caus-

ing poor handling, loss of vehi-

cle control, and sudden tire

failure leading to accidents,

injuries, and even death. The

recommended cold tire pres-

sure for your vehicle can be

found in this manual and on

the tire label located on the dri-

ver's side center pillar.

How to check

Use a good quality gage to check tire

pressure.You can not tell if your tires

are properly inflated simply by look-

ing at them. Radial tires may look

properly inflated even when they're

underinflated.

If you overfill the tire, release air by

pushing on the metal stem in the cen-

ter of the tire valve. Recheck the tire

pressure with the tire gage. Be sure to

put the valve caps back on the valve

stems. They help prevent leaks by

keeping out dirt and moisture.

Check the tire's inflation pressure

when the tires are cold. - "Cold"

means your vehicle has been sitting

for at least three hours or driven no

more than 1.6 km (1 mile).

• Worn tires can cause acci-

dents. Replace tires that are

worn, show uneven wear, or

are damaged.

• Remember to check the pres-

sure of your spare tire.

HYUNDAI recommends that

you check the spare every time

you check the pressure of the

other tires on your vehicle.

7-50

■ without a spare tire

Tire rotation

i

Information

To equalize tread wear, it is recom-

mended that the tires be rotated every

12,000 km (7,500 miles) or sooner if

irregular wear develops.

The outside and inside of the unsym-

metrical tire is distinguishable. When

installing an unsymmetrical tire, be

sure to install the side marked "out-

side" face the outside. If the side

marked "inside" is installed on the

outside, it will have a bad effect on

vehicle performance.

During rotation, check the tires for cor-

rect balance.

When rotating tires, check for uneven

wear and damage. Abnormal wear is

usually caused by incorrect tire pres-

sure, improper wheel alignment, out-

of-balance wheels, severe braking or

severe cornering. Look for bumps or

bulges in the tread or side of tire.

Replace the tire if you find either of

these conditions. Replace the tire if

fabric or cord is visible. After rotation,

be sure to bring the front and rear tire

pressures to specification and check

lug nut tightness.

WARNING

ODH073802

Disc brake pads should be inspected

for wear whenever tires are rotated.

• Do not use the compact spare

tire for tire rotation.

• Do not mix bias ply and radial

ply tires under any circum-

stances.This may cause unusu-

al handling characteristics that

could result in death, severe

injury, or property damage.

7

Refer to“Tire and wheels”in chap-

ter 8.

7-51

Maintenance

Wheel alignment and tire bal-

ance

Tire replacement

WARNING

Tread wear indicator

The wheels on your vehicle were

aligned and balanced carefully at the

factory to give you the longest tire life

and best overall performance.

When replacing the tires,

recheck and tighten the wheel

nuts after driving about 1,000

km (620 miles). If the steering

wheel shakes or the vehicle

vibrates while driving, the tire is

out of balance. Align the tire

balance. If the problem is not

solved, we recommend that you

contact an authorized HYUNDAI

dealer.

In most cases, you will not need to

have your wheels aligned again.

However, if you notice unusual tire

wear or your vehicle pulling one way

or the other, the alignment may need

to be reset.

OLMB073027

If you notice your vehicle vibrating

when driving on a smooth road, your

wheels may need to be rebalanced.

If the tire is worn evenly, a tread wear

indicator will appear as a solid band

across the tread. This shows there is

less than 1.6 mm (1/16 in.) of tread

left on the tire. Replace the tire when

this happens.

NOTICE

Improper wheel weights can

damage your vehicle's aluminum

wheels. Use only approved wheel

weights.

Do not wait for the band to appear

across the entire tread before replac-

ing the tire.

7-52

Compact spare tire replacement

(if equipped)

(Continued)

WARNING

• The use of any other tire size

or type may seriously affect

ride, handling, ground clear-

ance, stopping distance, body

to tire clearance, snow tire

clearance, and speedometer

reliability.

A compact spare tire has a shorter

tread life than a regular size tire.

Replace it when you can see the

tread wear indicator bars on the tire.

The replacement compact spare tire

should be the same size and design

tire as the one provided with your

new vehicle and should be mounted

on the same compact spare tire

wheel. The compact spare tire is not

designed to be mounted on a regular

size wheel, and the compact spare

tire wheel is not designed for mount-

ing a regular size tire.

• Driving on worn-out tires is

very hazardous and will

reduce braking effectiveness,

steering accuracy, and trac-

tion.

• Your vehicle is equipped with

tires designed to provide for

safe ride and handling capa-

bility. Do not use a size and

type of tire and wheel that is

different from the one that is

originally installed on your

vehicle. It can affect the safety

and performance of your vehi-

cle, which could lead to han-

dling failure or rollover and

serious injury.When replacing

the tires, be sure to equip all

four tires with the tire and

wheel of the same size, type,

tread, brand and load-carrying

capacity.

• When replacing tires (or

wheels), it is recommended to

replace the two front or two

rear tires (or wheels) as a pair.

Replacing just one tire can

seriously affect your vehicle’s

handling.

• The ABS works by comparing

the speed of the wheels. Tire

size can affect wheel speed.

When replacing tires, all 4

tires must use the same size

originally supplied with the

vehicle. Using tires of a differ-

ent size can cause the ABS

(Anti-lock Brake System) and

ESC (Electronic Stability

Control) (if equipped) to work

irregularly.

7

(Continued)

7-53

Maintenance

Wheel replacement

Tire traction

Tire sidewall labeling

When replacing the metal wheels for Tire traction can be reduced if you

any reason, make sure the new drive on worn tires, tires that are

wheels are equivalent to the original improperly inflated or on slippery

factory units in diameter, rim width road surfaces. Tires should be

1

5,6

7

and offset.

replaced when tread wear indicators

appear. To reduce the possibility of

losing control, slow down whenever

there is rain, snow or ice on the road.

4

WARNING

2

A wheel that is not the correct

size may adversely affect wheel

and bearing life, braking and

stopping abilities, handling char-

acteristics, ground clearance,

body-to-tire clearance, snow

chain clearance, speedometer

and odometer calibration, head-

lamp aim and bumper height.

3

Tire maintenance

In addition to proper inflation, correct

wheel alignment helps to decrease

tire wear. If you find a tire is worn

unevenly, have your dealer check the

wheel alignment.

1

OLMB073028

This information identifies and

describes the fundamental charac-

teristics of the tire and also provides

the tire identification number (TIN)

for safety standard certification. The

TIN can be used to identify the tire in

case of a recall.

When you have new tires installed,

make sure they are balanced. This

will increase vehicle ride comfort and

tire life. Additionally, a tire should

always be rebalanced if it is removed

from the wheel.

1. Manufacturer or brand name

Manufacturer or Brand name is shown.

7-54

215/70R16 100H

Wheel size designation

2. Tire size designation

215 - Tire width in millimeters.

Wheels are also marked with impor-

tant information that you need if you

ever have to replace one. The follow-

ing explains what the letters and

numbers in the wheel size designa-

tion mean.

A tire’s sidewall is marked with a tire

size designation. You will need this

information when selecting replace-

ment tires for your car. The following

explains what the letters and num-

bers in the tire size designation

mean.

70 - Aspect ratio. The tire’s section

height as a percentage of its

width.

R - Tire construction code (Radial).

16 - Rim diameter in inches.

100 - Load Index, a numerical code

associated with the maximum

load the tire can carry.

Example tire size designation:

Example wheel size designation:

(These numbers are provided as an

example only; your tire size designa-

tor could vary depending on your

vehicle.)

6.5JX16

H - Speed Rating Symbol. See the

speed rating chart in this section 6.5 - Rim width in inches.

for additional information.

J - Rim contour designation.

16 - Rim diameter in inches.

7

7-55

Maintenance

Tire speed ratings

3. Checking tire life

(TIN :Tire Identification

Number)

WARNING

The chart below lists many of the dif-

ferent speed ratings currently being

used for passenger car tires. The

speed rating is part of the tire size

designation on the sidewall of the

tire. This symbol corresponds to that

tire's designed maximum safe oper-

ating speed.

Tire age

Any tires that are over 6 years old,

based on the manufacturing date,

tire strength and performance,

decline with age naturally (even

unused spare tires). Therefore, the

tires (including the spare tire) should

be replaced by new ones. You can

find the manufacturing date on the

tire sidewall (possibly on the inside of

the wheel), displaying the DOT

Code. The DOT Code is a series of

numbers on a tire consisting of num-

bers and English letters. The manu-

facturing date is designated by the

last four digits (characters) of the

DOT code.

Tires degrade over time, even

when they are not being used.

Regardless of the remaining

tread, it is recommended that

tires generally be replaced after

six (6) years of normal service.

Heat caused by hot climates or

frequent high loading conditions

can accelerate the aging process.

Failure to follow this Warning can

result in sudden tire failure,

which could lead to a loss of con-

trol and an accident involving

serious injury or death.

Speed

Rating

Symbol

Maximum Speed

S

T

180 km/h (112 mph)

190 km/h (118 mph)

210 km/h (130 mph)

240 km/h (149 mph)

270 km/h (168 mph)

300 km/h (186 mph)

H

V

W

Y

DOT : XXXX XXXX OOOO

The front part of the DOT means a

plant code number, tire size and

tread pattern and the last four num-

bers indicate week and year manu-

factured.

For example:

DOT XXXX XXXX 1616 represents

that the tire was produced in the 16th

week of 2016.

7-56

Tread wear

4. Tire ply composition and

material

6. Maximum load rating

The tread wear grade is a compara-

tive rating based on the wear rate of

the tire when tested under controlled

conditions on a specified govern-

ment test course. For example, a tire

graded 150 would wear one-and-a-

half times (1½) as well on the gov-

ernment course as a tire graded 100.

This number indicates the maximum

load in kilograms and pounds that

can be carried by the tire. When

replacing the tires on the vehicle,

always use a tire that has the same

load rating as the factory installed

tire.

The number of layers or plies of rub-

ber-coated fabric are in the tire. Tire

manufacturers also must indicate the

materials in the tire, which include

steel, nylon, polyester, and others.

The letter "R" means radial ply con-

struction; the letter "D" means diago-

nal or bias ply construction; and the

letter "B" means belted-bias ply con-

struction.

The relative performance of tires

depends upon the actual conditions

of their use, however, and may

depart significantly from the norm

because of variations in driving

habits, service practices and differ-

ences in road characteristics and cli-

mate.

7. Uniform tire quality grading

Quality grades can be found where

applicable on the tire sidewall

between tread shoulder and maxi-

mum section width.

5. Maximum permissible infla-

tion pressure

For example:

This number is the greatest amount

of air pressure that should be put in

the tire. Do not exceed the maximum

permissible inflation pressure. Refer

to the Tire and Loading Information

label for recommended inflation

pressure.

TREADWEAR 200

TRACTION AA

TEMPERATURE A

These grades are molded on the

side-walls of passenger vehicle tires.

The tires available as standard or

optional equipment on your vehicles

may vary with respect to grade.

7

7-57

Maintenance

Traction - AA, A, B & C

Temperature -A, B & C

WARNING

The traction grades, from highest to The temperature grades are A (the

lowest, are AA, A, B and C. Those highest), B and C representing the

grades represent the tires ability to tire’s resistance to the generation of

stop on wet pavement as measured heat and its ability to dissipate heat

under controlled conditions on spec- when tested under controlled condi-

ified government test surfaces of tions on a specified indoor laboratory

asphalt and concrete. A tire marked test wheel.

Tire temperature

The temperature grade for this

tire is established for a tire that is

properly inflated and not over-

loaded. Excessive speed, under-

inflation, or excessive loading,

either separately or in combina-

tion, can cause heat build-up and

possible sudden tire failure. This

can cause loss of vehicle control

and serious injury or death.

C may have poor traction perform-

ance.

Sustained high temperature can

cause the material of the tire to

degenerate and reduce tire life, and

excessive temperature can lead to

sudden tire failure. Grades B and A

represent higher levels of perform-

ance on the laboratory test wheel

than the minimum required by the

law.

WARNING

The traction grade assigned to

this tire is based on straight-

ahead braking traction tests,

and does not include accelera-

tion, cornering, hydroplaning,

or peak traction characteristics.

7-58

Low aspect ratio tire

(if equipped)

NOTICE

The sidewall of the low aspect • It is difficult to recognize tire

The low aspect ratio tires, of which

aspect ratio is below 50, are equipped

with for the sporty look.

ratio tire is thinner than the high

aspect ratio tire. Thus, the wheel

and the tire may be easily damaged.

damage only with eyes. However,

we recommend you to have the

tire checked or replaced upon

detecting even the slightest tire

damage. The tire damage may

leak air from the tire.

Riding with high aspect ratio tires Thus, follow the below instructions.

may be uncomfortable with unpleas-

ant noises, because the low aspect

ratio tires are optimized for handling

and braking.

• Cautiously drive the vehicle on a

rough road or off the road.

Otherwise, the tires and wheels • Tire damage, caused by driving

may be damaged. After driving

those areas, inspect the tires

and wheels.

on a rough road, pothole, man-

hole or curb stone, or off the

road, is not covered by the man-

ufacturer’s warranty.

• Slowly drive the vehicle to pass

over a pothole, speed bump, man- • For further information about

hole, or curb stone. Otherwise, the

tires and wheels may be damaged.

the tire, refer to the label on the

tire sidewall.

• Upon having an impact on the

tire, we recommend you to have

the tires inspected by an author-

ized HYUNDAI dealer.

7

• Inspect the tires every 3,000 km

to prevent damage

7-59

Maintenance

FUSES

■ Blade type

A vehicle’s electrical system is pro-

tected from electrical overload dam-

age by fuses.

i

Information

Four kinds of fuses are used : blade type

for lower amperage rating, cartridge

type/Multi fuse/Battery fuse terminal for

higher amperage ratings.

This vehicle has 2 (or 3) fuse panels,

one located in the driver’s side panel

bolster, the other in the engine com-

partment near the battery.

Normal

Blown

■ Cartridge type

If any of your vehicle’s lights, acces-

sories, or controls do not work, check

the appropriate circuit fuse. If a fuse

has blown, the element inside the

fuse will be melted.

Normal

Blown

If the electrical system does not work,

first check the driver’s side fuse

panel. Before replacing a blown fuse,

turn the engine and all switches off,

and then disconnect the negative bat-

tery cable. Always replace a blown

fuse with one of the same rating.

■ Multi fuse

Normal

Blown

If the replacement fuse blows, this indi-

cates an electrical problem. Avoid

using the system involved and immedi-

ately consult an authorized HYUNDAI

dealer.

■ Battery fuse terminal

Blown

Normal

OLF074075

7-60

NOTICE

WARNING

Do not use a screwdriver or any • When replacing a blown fuse or

Fuse replacement

other metal object to remove fuses

because it may cause a short cir-

cuit and damage the system.

relay with a new one, make sure

the new fuse or relay fits tightly

into the clips. The incomplete fas-

tening fuse or relay may cause the

vehicle wiring and electric sys-

tems damage and a possible fire.

• Never replace a fuse with any-

thing but another fuse of the

same rating.

• A higher capacity fuse could

cause damage and possibly a

fire.

• Do not remove fuses, relays and

terminals fastened with bolts or

nuts. The fuses, relays and ter-

minals may be fastened incom-

pletely, and it may cause a pos-

sible fire. If fuses, relays and ter-

minals fastened with bolts or

nuts are blown, we recommend

that you consult an authorized

HYUNDAI dealer.

• Never install a wire or aluminum

foil instead of the proper fuse -

even as a temporary repair. It

may cause extensive wiring

damage and a possible fire.

• Do not input any other objects

except fuses or relays into

fuse/relay terminals such as a driv-

er or wiring. It may cause contact

failure and system malfunction.

7

7-61

Maintenance

Inner panel fuse replacement

i

Information

If you do not have a spare, use a fuse

of the same rating from a circuit you

may not need for operating the vehi-

cle, such as the cigar lighter fuse.

If the headlights or other electrical

components do not work and the

fuses are OK, check the fuse block in

the engine compartment. If a fuse is

blown, it must be replaced with the

same rating.

OTL075026

3. Pull the suspected fuse straight

out. Use the removal tool provided

in the engine compartment fuse

panel.

OTL075023

1. Turn the engine and all other

switches off.

2. Open the fuse panel cover.

4. Check the removed fuse; replace it

if it is blown.

5. Push in a new fuse of the same

rating, and make sure it fits tightly

in the clips.

If it fits loosely, we recommend that

you consult an authorized HYUNDAI

dealer.

7-62

Fuse switch

Engine compartment panel fuse

replacement

i

Information

OTL075025

OLF044148L

OTL075024

Always, place the fuse switch to the

ON position.

If the fuse switch is OFF, the above

message will appear.

1. Turn the engine off and all other

switches off.

If you move the switch to the OFF

position, some items such as the

audio system and digital clock must

be reset and the smart key may not

work properly.

NOTICE

2. Turn all the switches off.

3. Remove the fuse box cover by

pressing the tab and pulling up.

• Always place the fuse switch in

the ON position while driving the

vehicle.

7

4. Check the removed fuse; replace it

if it is blown. To remove or insert

the fuse, use the fuse puller in the

engine compartment fuse panel.

• Place the fuse switch in the OFF

position when the vehicle is

parked more than a month to

prevent battery discharge.

5. Push in a new fuse of the same

rating, and make sure it fits tightly

in the clips. If it fits loosely, we rec-

ommend that you consult an author-

ized HYUNDAI dealer.

• Do not move the transportation

fuse switch repeatedly. The fuse

switch may be damaged.

7-63

Maintenance

Main fuse

Multi fuse

NOTICE

After checking the fuse box in the

engine compartment, securely

install the fuse box cover. If not,

electrical failures may occur from

water leaking in.

OTL075027

OTL075028

If an electrical system does not oper- If the multi fuse is blown, it must be

ate with no blown fuse in the engine removed as follows:

room and inner fuse box, the main

1. Disconnect the negative battery

fuse inside the battery (+) cap may

cable.

be blown.

2. Remove the nuts shown in the pic-

The main fuse is heavily connected

ture above.

to many other parts. In this case, we

3. Replace the fuse with a new one

recommend you to contact an author-

of the same rating.

ized HYUNDAI dealer.

4. Reinstall in the reverse order of

removal.

i

Information

If the multi fuse is blown, we recom-

mend that you consult an authorized

HYUNDAI dealer.

7-64

Fuse/Relay panel description

Driver’s side fuse panel

OTL075067

Inside the fuse/relay box covers, you

can find the fuse/relay label describ-

ing fuse/relay name and capacity.

i

Information

7

Not all fuse panel descriptions in this

manual may be applicable to your

vehicle. It is accurate at the time of

printing. When you inspect the fuse

box on your vehicle, refer to the fuse

box label.

OTL077031L

7-65

Maintenance

Driver’s side fuse panel

Fuse Name

Symbol

Fuse Rating

Circuit Protected

A/C Control Module, Cluster Ionizer (Auto A/C),

E/R Junction Block (RLY.4, 5, 13)

A/CON 1

7.5A

RR WIPER

MODULE 6

WASHER

15A

10A

15A

Rear Wiper Motor, ICM Relay Box (Rear Wiper Relay)

BCM, Smart Key Control Module

Multifunction Switch (Washer Switch)

Crash Pad Switch, Rear Parking Assist Buzzer, BCM, 4WD ECM, AEB Sensor,

Steering Angle Sensor, Blind Spot Detection Radar LH/RH, Console Switch,

Smart Parking Assist Control Module, Lane Keeping Assist Control Module

MODULE 5

7.5A

A/BAG

15A

10A

7.5A

15A

7.5A

SRS Control Module

BCM, A/V & Navigation Head Unit, MTS Module, AUDIO, Low DC-DC Converter,

Smart Key Control Module, Power Outside Mirror Switch, PCB Block (Power Outlet Relay)

MODULE 1

START

ICM Relay Box (Burglar Alarm Relay), Transaxle Range Switch

Front Air Ventilation Seat Module, Front Seat Warmer Module,

Rear Seat Warmer

MODULE 7

HTD STRG

MODULE 8

BCM

Driver/Passenger Power Outside Mirror, Center Facia Switch,

Driver/Passenger Smart Key Outside Handle, Key Solenoid, AEB Sensor

7-66

Fuse Name

Symbol

Fuse Rating

Circuit Protected

Data Link Connector, A/C Control Module, ATM Shift Lever Ill.,

A/V & Navigation Head Unit, Electro Chromic Mirror,

Head Lamp Leveling Device Actuator LH/RH,

MODULE 4

7.5A

Auto Head Lamp Levelring Device Module, Crash Pad Switch, Front Air Ventilation Seat Module,

Low DC-DC Converter, Front Seat Warmer Module, Rear Seat Warmer, MTS Module

A/BAG IND

MODULE 3

SMART KEY 1

4WD

7.5A

10A

15A

20A

10A

15A

7.5A

10A

15A

Instrument Cluster, Center Facia Switch

BCM, ATM Shift Lever, Stop Lamp Switch

Smart Key Control Module

4WD ECM

T/GATE OPEN

S/HEATER RR

MDPS

Tail Gate Relay

Rear Seat Warmer

MDPS Unit

7

SMART KEY 3

CLUSTER

Immobilizer Module, Smart Key Control Module

Instrument Cluster

SMART KEY 2

MULTI MEDIA

Immobilizer Module, Smart Key Control Module, Start/Stop Button Switch

AUDIO, A/V & Navigation Head Unit, Low DC-DC Converter

7-67

Maintenance

Driver’s side fuse panel

Fuse Name

Symbol

Fuse Rating

Circuit Protected

INTERIOR

LAMP

Glove Box Lamp, Ignition Key Ill. & Door Warning Switch, Luggage Lamp, Front Vanity Lamp

Switch LH/RH, Room Lamp, Overhead Console Lamp, Rear Personal Lamp LH/RH

10A

Door Lock Relay, Door Unlock Relay,

ICM Relay Box (Dead Lock Relay)

DOOR LOCK

SUN ROOF 2

20A

7.5A

10A

30A

20A

10A

7.5A

Panorama Sunroof

POWER

OUTLET

Front Power Outlet & Cigarette Lighter

Stop Lamp Switch, Smart Key Control Module

BRAKE

SWITCH

Auto Light & Photo Sensor, Data Link Connector, UIP Sensor A/C Control Module, Instrument

Cluster, Electro Chromic Mirror, BCM, ICM Relay Box (Outside Mirror Folding/Unfolding Relay)

MEMORY 2

MEMORY 1

P/SEAT PASS

¹MEMORY

MTS Module

Passenger Seat Manual Switch

S/HEATER

FRT

Front Air Ventilation Seat Control Module, Front Seat Warmer Control Module

Panorama Sunroof

SUN ROOF 1

MODULE 2

PCB Block (Fuse - F44/F45/F49/F50/F52/F53)

ICM Relay Box (Rear Fog Lamp Relay)

A/C Control Module

RR FOG

LAMP

A/CON 2

7-68

Driver’s side fuse panel

Fuse Name

Symbol

Fuse Rating

Circuit Protected

HEATED

MIRROR

10A

A/C Control Module, Driver/Passenger Power Outside Mirror, ECM/PCM

P/SEAT DRV

30A

25A

Driver Seat Manual Switch

SAFETY

P/ WINDOW

Driver Safety Power Window Module

P/ WINDOW

RH

Power Window Main Switch, Passenger Power Window Switch

P/ WINDOW

LH

7

7-69

Maintenance

Engine compartment fuse panel

OTL075029

Inside the fuse/relay box covers, you

can find the fuse/relay label describ-

ing fuse/relay name and capacity.

i

Information

Not all fuse panel descriptions in this

manual may be applicable to your

vehicle. It is accurate at the time of

printing. When you inspect the fuse

box on your vehicle, refer to the fuse

box label.

OTLE077030

7-70

Engine compartment main fuse panel (Gasoline Engine)

Fuse Name

Symbol

Fuse rating

Circuit Protected

1

POWER

STEERING1

1

100A

MDPS Unit

POWER

STEERING2

2

1

80A

60A

50A

40A

30A

50A

B+ 1

B+ 2

B+ 3

ABS 1

ABS 2

IG1

Smart Junction Block (IPS1, IPS2, IPS3, IPS4)

MULTI

FUSE

Smart Junction Block (IPS5, IPS6, IPS7, IPS8, IPS9, Fuse - F19/F28/F35/F42)

ESP Control Module, ABS Control Module, Multipurpose Check Connector

W/O Smart Key : Ignition Switch

With Smart Key : PCB Block (PDM (IG1) Relay, PDM (ACC) Relay)

7

W/O Smart Key : Ignition Switch

With Smart Key : PCB Block (PDM (IG2) Relay)

IG2

Smart Junction Block (Fuse - F14/F21/F22/F31/F38/F45/F40/F46,

Leak Current Autocut Device)

B+ 4

COOLING

FAN1

(50A)

[60A]

(G4NA/G4FD) : E/R Junction Block (RLY. 1, RLY. 9)

(G4FJ) : E/R Junction Block (RLY. 1)

FUSE

E-CVVT1

E-CVVT2

E-CVVT1

E-CVVT2

20A

ECVVT RLY 1

ECVVT RLY 2

7-71

Maintenance

Engine compartment main fuse panel (Gasoline Engine)

Fuse Name

Symbol

Fuse rating

Circuit Protected

TCU 3

40A

TCM

TCU 4

40A

TCM

BLOWER

E/R Junction Block (RLY. 13)

Power Tail Gate Module

E/R Junction Block (RLY. 2)

FUSE

POWER

TAILGATE

REAR

HEATED

REAR

HEATED

COOLING

FAN2

2

G4FJ : E/R Junction Block (RLY. 9)

7-72

Engine compartment main fuse panel (Diesel Engine)

Fuse Name

Symbol

Fuse rating

Circuit Protected

1

POWER

STEERING1

1

100A

MDPS Unit

POWER

STEERING2

2

1

80A

60A

50A

40A

30A

50A

B+ 1

B+ 2

Smart Junction Block (IPS1, IPS2, IPS3, IPS4)

Smart Junction Block (IPS5, IPS6, IPS7, IPS8, IPS9, Fuse - F19/F28/F35/F42)

Smart Junction Block (Fuse - F23/F32/F39/F40/F46, Power Window Relay)

ESP Control Module, ABS Control Module, Multipurpose Check Connector

B+ 3

ABS 1

ABS 2

IG1

MULTI

FUSE

W/O Smart Key : Ignition Switch

With Smart Key : PCB Block (PDM (IG1) Relay, PDM (ACC) Relay)

7

W/O Smart Key : Ignition Switch

With Smart Key : PCB Block (PDM (IG2) Relay)

IG2

GLOW PLUG

Glow Relay Unit

1

PTC 1

HEATER

PTC

HEATER

E/R Junction Block (RLY. 6)

E/R Junction Block (RLY. 5)

E/R Junction Block (RLY. 4)

2

PTC 2

HEATER

PTC

HEATER

3

PTC 3

HEATER

PTC

HEATER

7-73

Maintenance

Engine compartment main fuse panel (Diesel Engine)

Fuse Name

Symbol

Fuse rating

Circuit Protected

Smart Junction Block (Fuse - F14/F21/F22/F31/F38/F45/F40/F46,

Leak Current Autocut Device)

B+ 4

50A

COOLING

FAN1

(50A)

[60A]

(G4NA/G4FD) : E/R Junction Block (RLY. 1, RLY. 9)

(G4FJ) : E/R Junction Block (RLY. 1)

TCU 3

TCU 4

40A

30A

40A

TCM

FUSE

BLOWER

E/R Junction Block (RLY. 13)

Power Tail Gate Module

E/R Junction Block (RLY. 10)

E/R Junction Block (RLY. 2)

G4FJ : E/R Junction Block (RLY. 9)

POWER

TAILGATE

FUEL

HEATER

REAR

HEATED

REAR

HEATED

COOLING

FAN2

2

7-74

LIGHT BULBS

Consult an authorized HYUNDAI

dealer to replace most vehicle light

bulbs. It is difficult to replace vehicle

light bulbs because other parts of the

vehicle must be removed before you

can get to the bulb. This is especially

true for removing the headlamp

assembly to get to the bulb(s).

NOTICE

i

Information

- Traffic Change

(for Europe)

Be sure to replace the burned-out

bulb with one of the same wattage The low beam light distribution is

rating. Otherwise, it may cause asymmetric. If you go abroad to a coun-

damage to the fuse or electric try with opposite traffic direction, this

wiring system.

asymmetric part will dazzle oncoming

car driver. To prevent dazzle, ECE reg-

ulation demand several technical solu-

tions (ex. automatic change system,

adhesive sheet, down aiming). These

headlamps are designed not to dazzle

opposite drivers. So, you need not

change your headlamps in a country

with opposite traffic direction.

i

Information

Removing/installing the headlamp

assembly can result in damage to

the vehicle.

After heavy driving, rain or washing,

headlamp and tail lamp lenses could

appear frosty. This condition is caused

by the temperature difference between

the lamp inside and outside. This is

similar to the condensation on your

windows inside your vehicle during the

rain and doesn’t indicate a problem

with your vehicle. If the water leaks

into the lamp bulb circuitry, we rec-

ommend that the system be checked

by an authorized HYUNDAI dealer.

WARNING

Prior to working on the light,

firmly apply the parking brake,

ensure that the ignition switch is

in the LOCK/OFF position and

turn off the lights to avoid sud-

den movement of the vehicle and

burning your fingers or receiving

an electric shock.

7

7-75

Maintenance

■ Halogen bulb

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

Headlamp, static bending lamp,

position lamp, turn signal lamp

and fog lamp light bulb replace-

ment

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

Type A

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OLMB073042L

Headlamp and Static bending lamp

WARNING

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

OTL075064

(1) Headlamp (Low)

(2) Headlamp (High)

(3) Turn signal lamp

(4) Position lamp

• Wear eye protection when

changing a bulb. Allow the bulb

to cool down before handling it.

(5) Daytime running lamp

(6) Fog lamp

(7) Static bending lamp

(if equipped)

7-76

■ High/Low beam

5. Unsnap the bulb retaining wire by

pressing the end and pushing it

upward.

6. Remove the bulb from the head-

lamp assembly.

7. Install a new bulb and snap the

bulb retaining wire into position by

aligning the wire with the groove

on the bulb.

Low

High

8. Connect the bulb socket-connec-

tor.

OTLE075013

■ Static bending lamp

OTLE075019

9. Install the bulb cover by turning it

clockwise.

Turn signal lamp

1. Open the hood.

2. Disconnect the negative battery

cable.

i

Information

The headlamp aiming should be adjust-

ed after an accident or after the head-

lamp assembly is reinstalled at an

authorized HYUNDAI dealer.

3.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

7

OTLE075015

1. Open the hood.

4.Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

2. Disconnect the negative battery

cable.

3. Remove the bulb cover by turning

it counterclockwise.

4. Disconnect the bulb socket-con-

nector.

7-77

Maintenance

■ Halogen bulb

5.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

Type B

6.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

Position lamp/Daytime running

lamp/Fog lamp

OLMB073042L

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

Headlamp (High beam)

OTL075032

(1) Headlamp (Low)

(2) Headlamp (High)

(3) Turn signal lamp

(4) Position lamp

WARNING

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

(5) Daytime running lamp

(6) Fog lamp

(7) Static bending lamp

• Wear eye protection when

changing a bulb. Allow the bulb

to cool down before handling it.

7-78

■ High beam

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

6. Remove the bulb from the head-

lamp assembly.

7. Install a new bulb and snap the

bulb retaining wire into position by

aligning the wire with the groove

on the bulb.

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

8. Connect the bulb socket-connec-

tor.

• A bulb should be operated only

when installed in a headlamp.

9. Install the bulb cover by turning it

clockwise.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OTLE075014

1. Open the hood.

2. Disconnect the negative battery

cable.

3. Remove the bulb cover by turning

it counterclockwise.

4. Disconnect the bulb socket-con-

nector.

7

5. Unsnap the bulb retaining wire by

pressing the end and pushing it

upward.

7-79

Maintenance

Headlamp (Low, LED type)

5.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

6.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

i

Information

The headlamp aiming should be adjust-

ed after an accident or after the head-

lamp assembly is reinstalled at an

authorized HYUNDAI dealer.

Position lamp/ Daytime running lamp/

Fog lamp/Static bending lamp

OTLE075019

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

Turn signal lamp

1. Open the hood.

2. Disconnect the negative battery

cable.

3.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7-80

7.Connect the bulb electrical con-

nector.

Type B

Side repeater lamp replace-

ment

8.Reinstall the lamp assembly to the

body of the vehicle.

Type A

OTL075065

1.Remove the lamp assembly from

the vehicle by prying the lens and

pulling the assembly out.

OTL075066

If the light bulb does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

2.Disconnect the bulb electrical con-

nector.

3.Separate the socket and the lens

parts by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots on the

lens part.

7

4.Remove the bulb by pulling it

straight out.

5.Insert a new bulb in the socket.

6.Reassemble the socket and the

lens part.

7-81

Maintenance

4. With the headlamp and battery in

normal condition, aim the head-

lamps so the brightest portion falls

on the horizontal and vertical

lines.

Front fog lamp aiming

Headlamp and front fog lamp

aiming (for Europe)

Headlamp aiming

5. To aim the low beam left or right,

turn the driver clockwise or coun-

terclockwise. To aim the low beam

up or down, turn the driver clock-

wise or counterclockwise.

To aim the high beam up or down,

turn the driver clockwise or coun-

terclockwise.

OTLE075021

The front fog lamp can be aimed as

the same manner of the headlamps

aiming.

OTLE075020

1. Inflate the tires to the specified

pressure and remove any loads

from the vehicle except the driver,

spare tire, and tools.

With the front fog lamps and battery

in normal condition, aim the front fog

lamps.

To aim the front fog lamp up or down,

turn the driver clockwise or counter-

clockwise.

2. The vehicle should be placed on a

flat floor.

3. Draw vertical lines (Vertical lines

passing through respective head

lamp centers) and a horizontal line

(Horizontal line passing through

center of head lamps) on the

screen.

7-82

Aiming point

H1 : Height between the head lamp bulb center and ground (Low beam)

H2 : Height between the head lamp bulb center and ground (High beam)

H3 : Height between the fog lamp bulb center and ground

W1 : Distance between the two head lamp bulbs centers (Low beam)

W2 : Distance between the two head lamp bulbs centers (High beam)

W3 : Distance between the two fog lamp bulbs centers

7

OTLE075022

Unit: mm (in)

H3

FOG+DRL

W3

Vehicle

condition

Lamp type

H1

H2

W1

W2

FOG

FOG+DRL

Halogen/HID 886 (34.89)

LED 884 (34.80)

Halogen/HID 879 (34.60)

LED 877 (34.53)

1502 (59.13)

1494 (58.82)

1502 (59.13)

1494 (58.82)

862

(33.94)

578

(22.76)

Without driver

With driver

565 (22.24)

558 (21.97)

1208 (47.56) 1474 (58.03) 1452 (57.17)

855

(33.66)

571

(22.48)

1208 (47.56) 1474 (58.03) 1452 (57.17)

7-83

Maintenance

Headlamp low beam (LHD side)

■ Based on 10m screen

OTLE075100

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If headlamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

7-84

Headlamp low beam (RHD side)

■ Based on 10m screen

7

OTLE075101

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If headlamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

7-85

Maintenance

Front fog lamp

■ Based on 10m screen

OTLE075102

1. Turn the front fog lamp on without the driver aboard.

2. The cut-off line should be projected in the allowable range (shaded region).

7-86

3. Loosen the lamp assembly retain-

ing screws with a cross-tip screw-

driver.

Outside lamp

Rear combination light bulb

replacement

Stop/tail Lamp and Turn signal

lamp

■ Type A

4. Remove the rear combination

lamp assembly from the body of

the vehicle.

OTL075034

■ Type B

OTL075035

7

OTL075034

OTL075036

(1) Stop lamp

1. Turn off the engine.

2. Open the tailgate.

(2) Tail lamp

(3) Rear turn signal lamp

(4) Back-up lamp

7-87

Maintenance

8.Install the socket in the assembly by Stop/tail lamp (LED type)

aligning the tabs on the socket with

the slots in the assembly.

Push the socket into the assembly checked by an authorized HYUNDAI

If the LED lamp does not operate, we

recommend you to have the vehicle

Stop/tail lamp

and turn the socket clockwise.

dealer.

9.Reinstall the lamp assembly to the

body of the vehicle.

Turn Signal lamp

OTL075037

5.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on the

assembly.

6.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

7-88

Stop and tail lamp (LED type)

Inside lamp

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

Tail lamp/Back-up lamp

OTL075039

4.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OTLE075016

1. Turn off the engine.

2. Open the tailgate.

5.Pull the bulb out of the socket.

6.Insert a new bulb into the socket.

3. Remove the service cover using a

flat-blade screwdriver.

7.Install the socket into the assembly

by aligning the tabs on the socket

with the slots on the assembly and

turning the socket clockwise.

7

8.Reinstall the lamp assembly to the

body of the vehicle

7-89

Maintenance

Rear fog lamp (if equipped)

High mounted stop lamp

replacement

License plate light bulb

replacement

1.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

2.Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

3.Insert a new bulb in the socket.

OTL075040

OTL075041

4.Reinstall the light assembly to the

body of the vehicle.

If the high mounted stop lamp does not 1.Loosen the lens retaining screws

operate, we recommend that you con-

tact an authorized HYUNDAI dealer.

with a screwdriver.

2.Remove the lens.

3.Remove the bulb by pulling it straight

out.

4.Install a new bulb.

5.Reinstall the lens securely with the

lens retaining screws.

7-90

Interior light bulb replacement

Map lamp, Room lamp, Vanity mirror lamp, Tailgate room lamp and

glove box lamp

Map lamp and Room lamp

■ Map lamp - with sunroof

■ Map lamp - without sunroof

■ Vanity mirror lamp

OTLE075017

OTLE075018

OTL075043

■ Room lamp - with sunroof

■ Room lamp - without sunroof

■ Tailgate room lamp

7

OTL075044

OLFH074029

OTL075045

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

7-91

Maintenance

■ Glove box lamp

NOTICE

Be careful not to damage the cover,

tab, and plastic housing.

OTL075046

1. Using a flat-head screwdriver,

gently pry the lens from the interi-

or light housing.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior

light housing notches and snap

the lens into place.

7-92

APPEARANNCE CARRE

Exterior care

Finish maintenance

NOTICE

Washing

Exterior general caution

• Do not use strong soap, chemi-

cal detergents or hot water, and

do not wash the vehicle in direct

sunlight or when the body of the

vehicle is warm.

To help protect your vehicle’s finish

from rust and deterioration, wash it

thoroughly and frequently at least

once a month with lukewarm or cold

water.

If you use your vehicle for off-road

driving, you should wash it after each

off-road trip. Pay special attention to

the removal of any accumulation of

salt, dirt, mud, and other foreign

materials. Make sure the drain holes

in the lower edges of the doors and

rocker panels are kept clear and

clean.

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning

and caution statements that appear

on the label.

• Be careful when washing the

side windows of your vehicle.

Especially, with high-pressure

water, water may leak through

the windows and wet the interior.

• To prevent damage to the plastic

parts and lamps, do not clean

with chemical solvents or strong

detergents.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar deposits

can damage your vehicle’s finish if not

removed immediately.

Even prompt washing with plain water

may not completely remove all these

deposits.

A mild soap, safe for use on painted

surfaces, may be used.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water.

Do not allow soap to dry on the finish.

WARNING

Wet brakes

7

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water. If braking performance

is impaired, dry the brakes by

applying them lightly while main-

taining a slow forward speed.

7-93

Maintenance

High-pressure washing

Waxing

Wax the vehicle when water will no

longer bead on the paint.

• When using high-pressure washers,

make sure to maintain sufficient dis-

tance from the vehicle.

Always wash and dry the vehicle

before waxing. Use a good quality

liquid or paste wax, and follow the

manufacturer’s instructions. Wax all

metal trim to protect it and to main-

tain its luster. Removing oil, tar, and

similar materials with a spot remover

will usually strip the wax from the fin-

ish. Be sure to re-wax these areas

even if the rest of the vehicle does

not yet need waxing.

Insufficient clearance or excessive

pressure can lead to component

damage or water penetration.

• Do not spray the camera, sensors or

its surrounding area directly with a

high pressure washer. Shock

applied from high pressure water

may cause the device to not operate

normally.

OLMB073082

NOTICE

• Do not bring the nozzle tip close to

boots (rubber or plastic covers) or

connectors as they may be dam-

aged if they come into contact with

high pressure water.

• Water washing in the engine com-

partment including high pressure

water washing may cause the fail-

ure of electrical circuits located in

the engine compartment.

NOTICE

• Wiping dust or dirt off the body

with a dry cloth will scratch the

finish.

• Never allow water or other liquids

to come in contact with electri-

cal/electronic components inside

the vehicle as this may damage

them.

• Do not use steel wool, abrasive

cleaners, or strong detergents

containing highly alkaline or

caustic agents on chrome-plated

or anodized aluminum parts.This

may result in damage to the pro-

tective coating and cause discol-

oration or paint deterioration.

7-94

Finish damage repair

Bright-metal maintenance

Underbody maintenance

Deep scratches or stone chips in the • To remove road tar and insects, Corrosive materials used for ice and

painted surface must be repaired

promptly. Exposed metal will quickly

rust and may develop into a major

repair expense.

use a tar remover, not a scraper or snow removal and dust control may

other sharp object.

collect on the underbody. If these

materials are not removed, acceler-

ated rusting can occur on underbody

parts such as the fuel lines, frame,

floor pan and exhaust system, even

though they have been treated with

rust protection.

• To protect the surfaces of bright-

metal parts from corrosion, apply a

coating of wax or chrome preser-

vative and rub to a high luster.

NOTICE

• During winter weather or in coastal

areas, cover the bright metal parts

with a heavier coating of wax or

preservative. If necessary, coat the

parts with non-corrosive petroleum

jelly or other protective compound.

If your vehicle is damaged and

requires any metal repair or

replacement, be sure the body

shop applies anti-corrosion materi-

als to the parts repaired or replaced.

Thoroughly flush the vehicle under-

body and wheel openings with luke-

warm or cold water once a month,

after off-road driving and at the end of

each winter. Pay special attention to

these areas because it is difficult to

see all the mud and dirt. It will do

more harm than good to wet down the

road grime without removing it. The

lower edges of doors, rocker panels,

and frame members have drain holes

that should not be allowed to clog with

dirt; trapped water in these areas can

cause rusting.

7

7-95

Maintenance

Aluminum wheel maintenance

Corrosion protection

WARNING

The aluminum wheels are coated with Protecting your vehicle from corro-

a clear protective finish.

sion

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water. If braking performance

is impaired, dry the brakes by

applying them lightly while main-

taining a slow forward speed.

By using the most advanced design

and construction practices to combat

corrosion, we produces cars of the

highest quality. However, this is only

part of the job. To achieve the long-

term corrosion resistance your vehi-

cle can deliver, the owner's coopera-

tion and assistance is also required.

NOTICE

• Do not use any abrasive cleaner,

polishing compound, solvent,

or wire brushes on aluminum

wheels.

• Clean the wheel when it has

cooled.

• Use only a mild soap or neutral

detergent, and rinse thoroughly

with water. Also, be sure to clean

the wheels after driving on salted

roads.

Common causes of corrosion

The most common causes of corro-

sion on your car are:

• Road salt, dirt and moisture that is

allowed to accumulate underneath

the car.

• Do not wash the wheels with high-

speed car wash brushes.

• Removal of paint or protective coat-

ings by stones, gravel, abrasion or

minor scrapes and dents which

leave unprotected metal exposed to

corrosion.

• Do not use any cleanser contain-

ing acid or alkaline detergents.

7-96

High-corrosion areas

High temperatures can also acceler- Keep your car clean

ate corrosion of parts that are not

If you live in an area where your car

is regularly exposed to corrosive

materials, corrosion protection is

particularly important. Some of the

common causes of accelerated cor-

rosion are road salts, dust control

chemicals, ocean air and industrial

pollution.

The best way to prevent corrosion is

properly ventilated so the moisture

can be dispersed. For all these rea-

sons, it is particularly important to

keep your car clean and free of mud

or accumulations of other materials.

This applies not only to the visible sur-

faces but particularly to the underside

of the car.

to keep your car clean and free of

corrosive materials. Attention to the

underside of the car is particularly

important.

• If you live in a high-corrosion area

— where road salts are used, near

the ocean, areas with industrial

pollution, acid rain, etc.—, you

should take extra care to prevent

corrosion. In winter, hose off the

underside of your car at least once

a month and be sure to clean the

underside thoroughly when winter

is over.

Moisture breeds corrosion

To help prevent corrosion

Moisture creates the conditions in

which corrosion is most likely to occur.

For example, corrosion is accelerated

by high humidity, particularly when

temperatures are just above freezing.

In such conditions, the corrosive

material is kept in contact with the car

surfaces by moisture that is slow to

evaporate.

You can help prevent corrosion from

getting started by observing the fol-

lowing:

• When cleaning underneath the car,

give particular attention to the

components under the fenders and

other areas that are hidden from

view. Do a thorough job; just damp-

ening the accumulated mud rather

than washing it away will acceler-

ate corrosion rather than prevent

it. Water under high pressure and

steam are particularly effective in

removing accumulated mud and

corrosive materials.

7

Mud is particularly corrosive because

it is slow to dry and holds moisture in

contact with the vehicle. Although the

mud appears to be dry, it can still

retain the moisture and promote cor-

rosion.

7-97

Maintenance

• When cleaning lower door panels, Keep paint and trim in good con- Don't neglect the interior

rocker panels and frame members, dition

Moisture can collect under the floor

be sure that drain holes are kept

open so that moisture can escape

and not be trapped inside to accel-

erate corrosion.

Scratches or chips in the finish mats and carpeting to cause corro-

should be covered with "touch-up" sion. Check under the mats periodi-

paint as soon as possible to reduce cally to be sure the carpeting is dry.

the possibility of corrosion. If bare Use particular care if you carry fertil-

metal is showing through, the atten- izers, cleaning materials or chemi-

tion of a qualified body and paint cals in the car.

Keep your garage dry

shop is recommended.

These should be carried only in

proper containers and any spills or

leaks should be cleaned up, flushed

with clean water and thoroughly

dried.

Don't park your car in a damp, poor-

ly ventilated garage. This creates a

favorable environment for corrosion. Bird droppings : Bird droppings are

This is particularly true if you wash highly corrosive and may damage

your car in the garage or drive it into painted surfaces in just a few hours.

the garage when it is still wet or cov- Always remove bird droppings as

ered with snow, ice or mud. Even a soon as possible.

heated garage can contribute to cor-

rosion unless it is well ventilated so

moisture is dispersed.

7-98

Cleaning the upholstery and

interior trim

Cleaning the lap/shoulder belt

webbing

Interior care

Interior general precautions

Vinyl

Clean the belt webbing with any mild

soap solution recommended for clean-

ing upholstery or carpet. Follow the

instructions provided with the soap. Do

not bleach or re-dye the webbing

because this may weaken it.

Prevent chemicals such as perfume,

cosmetic oil, sun cream, hand cleaner

and air freshener from contacting the

interior parts because they may

cause damage or discoloration. If they

do contact the interior parts, wipe them

off immediately.

Remove dust and loose dirt from

vinyl with a whisk broom or vacuum

cleaner. Clean vinyl surfaces with a

vinyl cleaner.

Fabric

See the instructions that follow for

the proper way to clean vinyl.

Cleaning the interior window

glass

Remove dust and loose dirt from fabric

with a whisk broom or vacuum cleaner.

Clean with a mild soap solution recom-

mended for upholstery or carpets.

If the interior glass surfaces of the

vehicle become fogged (that is, cov-

ered with an oily, greasy or waxy film),

they should be cleaned with glass

cleaner. Follow the directions on the

glass cleaner container.

NOTICE

Never allow water or other liquids to

come in contact with electrical/elec-

tronic components inside the vehi-

cle as this may damage them.

Remove fresh spots immediately with

a fabric spot cleaner. If fresh spots do

not receive immediate attention, the

fabric can be stained and its color can

be affected. Also, its fire-resistant prop-

erties can be reduced if the material is

not properly maintained.

NOTICE

7

Do not scrape or scratch the inside

of the rear window.This may result

in damage to the rear window

defroster grid.

When cleaning leather products

(steering wheel, seats etc.), use

neutral detergents or low alcohol

content solutions. If you use high

alcohol content solutions or acid/

alkaline detergents, the color of

the leather may fade or the sur-

face may get stripped off.

NOTICE

Using anything but recommended

cleaners and procedures may affect

the fabric’s appearance and fire-

resistant properties.

7-99

Maintenance

EMISSION COONTROL SYSTEM

The emission control system of your

vehicle is covered by a written limited

warranty. Please see the warranty

information contained in the Service

Passport in your vehicle.

1. Crankcase emission control

system

CAUTION

The positive crankcase ventilation

system is employed to prevent air

pollution caused by blow-by gases

being emitted from the crankcase.

This system supplies fresh filtered air

to the crankcase through the air

intake hose. Inside the crankcase,

the fresh air mixes with blow-by

gases, which then pass through the

PCV valve into the induction system.

For the Inspection and Maintenance

Test (With Electronic Stability Control

(ESC) system)

Your vehicle is equipped with an

emission control system to meet all

emission regulations.

• To prevent the vehicle from

misfiring during dynamome-

ter testing, turn the Electronic

Stability Control (ESC) sys-

tem off by pressing the ESC

switch.

There are three emission control

systems which are as follows.

(1) Crankcase emission control sys-

tem

• After dynamometer testing is

completed, turn the ESC sys-

tem back on by pressing the

ESC switch again.

2. Evaporative emission con-

trol system

(2) Evaporative emission control sys-

tem

(3) Exhaust emission control system

The Evaporative Emission Control

System is designed to prevent fuel

vapors from escaping into the atmos-

phere.

In order to assure the proper function

of the emission control systems, it is

recommended that you have your car

inspected and maintained by an

authorized HYUNDAI dealer in accor-

dance with the maintenance schedule

in this manual.

7-100

Canister

Engine exhaust gas precautions

(carbon monoxide)

3. Exhaust emission control

system

Fuel vapors generated inside the fuel

tank are absorbed and stored in the

onboard canister.When the engine is

running, the fuel vapors absorbed in

the canister are drawn into the surge

tank through the purge control sole-

noid valve.

• Carbon monoxide can be present

with other exhaust fumes.Therefore,

if you smell exhaust fumes of any

kind inside your vehicle, have it

inspected and repaired immediately.

If you ever suspect exhaust fumes

are coming into your vehicle, drive it

only with all the windows fully open.

Have your vehicle checked and

repaired immediately.

The Exhaust Emission Control System

is a highly effective system which con-

trols exhaust emissions while main-

taining good vehicle performance.

Vehicle modifications

This vehicle should not be modified.

Modification of your vehicle could

affect its performance, safety or

durability and may even violate gov-

ernmental safety and emissions reg-

ulations.

Purge Control Solenoid Valve

(PCSV)

The purge control solenoid valve is

controlled by the Engine Control

Module (ECM); when the engine

coolant temperature is low during

idling, the PCSV closes so that evap-

orated fuel is not taken into the

engine. After the engine warms-up

during ordinary driving, the PCSV

opens to introduce evaporated fuel to

the engine.

In addition, damage or performance

problems resulting from any modifi-

cation may not be covered under

warranty.

• If you use unauthorized electronic

devices, it may cause the vehicle to

operate abnormally, wire damage,

battery discharge and fire. For your

safety, do not use unauthorized

electronic devices.

7

7-101

Maintenance

• Do not operate the engine in con-

fined or closed areas (such as

garages) any more than what is

necessary to move the vehicle in or

out of the area.

Operating precautions for cat-

alytic converters (if equipped)

WARNING

Engine exhaust gases contain

carbon monoxide (CO). Though

colorless and odorless, it is dan-

gerous and could be lethal if

inhaled. Follow the instructions

following to avoid CO poisoning.

WARNING

• When the vehicle is stopped in an

open area for more than a short

time with the engine running,

adjust the ventilation system (as

needed) to draw outside air into the

vehicle.

• A hot exhaust system can

ignite flammable items under

your vehicle. Do not park, idle,

or drive the vehicle over or

near flammable objects, such

as dry grass, paper, leaves, etc.

• Never sit in a parked or stopped

vehicle for any extended time with

the engine running.

• The exhaust system and cat-

alytic system are very hot while

the engine is running or imme-

diately after the engine is

turned off. Keep away from the

exhaust system and catalytic,

you may get burned.

• When the engine stalls or fails to

start, excessive attempts to restart

the engine may cause damage to

the emission control system.

Also, do not remove the heat

sink around the exhaust sys-

tem, do not seal the bottom of

the vehicle or do not coat the

vehicle for corrosion control. It

may present a fire risk under

certain conditions.

7-102

Your vehicle is equipped with a cat-

alytic converter emission control

device.

Failure to observe these precautions

could result in damage to the catalytic

converter and to your vehicle.

(Continued)

• Do not operate the engine at

high idle speed for extended

periods (5 minutes or more).

Therefore, the following precautions

must be observed:

Additionally, such actions could void

your warranties.

• Do not modify or tamper with

any part of the engine or emis-

sion control system. All inspec-

tions and adjustments must be

made by an authorized HYUNDAI

dealer.

CAUTION

• Use only UNLEADED FUEL for

gasoline engine.

• Do not operate the vehicle when

there are signs of engine mal-

function, such as misfire or a

noticeable loss of performance.

• Avoid driving with a very low

fuel level. If you run out of

gasoline, it could cause the

engine to misfire and result in

excessive loading of the cat-

alytic converter.

• Do not misuse or abuse the

engine. Examples of misuse are

coasting with the engine off and

descending steep grades in

gear with the engine off.

(Continued)

7

7-103

Maintenance

The Malfunction Indicator Lamp (MIL)

stops illuminating, when the driving

speed exceeds 60 km/h (37mph), or

when the engine rpm is between

1,500 and 2,500 with the gear in the

2nd position or above for approxi-

mately 25 minutes.

Diesel particulate filter (DPF)

(if equipped)

CAUTION

The Diesel Particulate Filter (DPF)

system removes the soot in the

exhaust gas.

Diesel Fuel

(if equipped with DPF)

We recommend you to use only

the regulated diesel fuels, when

your vehicle is equipped with

the DPF system.

The DPF system automatically burns

(or oxidizes) the accumulated soot in

accordance with the driving situa-

tions, unlike a disposable air filter.

When the MIL continuously blinks or

the warning message “Check exhaust

system” illuminates in the above

cases, we recommend you to have the

DPF system checked by an author-

ized HYUNDAI dealer.

When you use other diesel fuels,

which is high in sulfurs (above

50 ppm) or contains unspecified

additives, it may damage the

DPF system and cause the white

smoke emission.

In other words, the accumulated soot

is automatically purged out by the

engine control system and by the high

exhaust-gas temperature at normal/

high driving speeds.

When the vehicle is continuously driv-

en with the MIL flashing for an extend-

ed period of time, it may damage the

DPF system and lower the fuel econ-

omy.

However, when the vehicle is continu-

ally driven at repeated short distance

or driven at low speed for a long time,

the accumulated soot may not be

automatically removed because of low

exhaust gas temperature. In this case,

the accumulated soot is out of the

detection range, the soot oxidization

process does not occur, and the

Lean NOx Trap (if equipped)

The Lean NOx Trap (LNT) system

removes the nitrogen oxide in the

exhaust gas. The smell can occur in

the exhaust gas depending on the

quality of the fuel and it can degrade

NOx reduction performance, please

use the regulated automotive diesel

fuel.

Malfunction Indicator Lamp (

Illuminates.

)

7-104

Maintenance for Your Hyundai Tucson SUV Third Generation (2016-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals