Get Maintenance -> Light bulbs Guide for Hyundai Tucson SUV Third Generation (2016-2019)

LIGHT BULBS

Consult an authorized HYUNDAI

dealer to replace most vehicle light

bulbs. It is difficult to replace vehicle

light bulbs because other parts of the

vehicle must be removed before you

can get to the bulb. This is especially

true for removing the headlamp

assembly to get to the bulb(s).

NOTICE

i

Information

- Traffic Change

(for Europe)

Be sure to replace the burned-out

bulb with one of the same wattage The low beam light distribution is

rating. Otherwise, it may cause asymmetric. If you go abroad to a coun-

damage to the fuse or electric try with opposite traffic direction, this

wiring system.

asymmetric part will dazzle oncoming

car driver. To prevent dazzle, ECE reg-

ulation demand several technical solu-

tions (ex. automatic change system,

adhesive sheet, down aiming). These

headlamps are designed not to dazzle

opposite drivers. So, you need not

change your headlamps in a country

with opposite traffic direction.

i

Information

Removing/installing the headlamp

assembly can result in damage to

the vehicle.

After heavy driving, rain or washing,

headlamp and tail lamp lenses could

appear frosty. This condition is caused

by the temperature difference between

the lamp inside and outside. This is

similar to the condensation on your

windows inside your vehicle during the

rain and doesn’t indicate a problem

with your vehicle. If the water leaks

into the lamp bulb circuitry, we rec-

ommend that the system be checked

by an authorized HYUNDAI dealer.

WARNING

Prior to working on the light,

firmly apply the parking brake,

ensure that the ignition switch is

in the LOCK/OFF position and

turn off the lights to avoid sud-

den movement of the vehicle and

burning your fingers or receiving

an electric shock.

7

7-75

Maintenance

■ Halogen bulb

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

Headlamp, static bending lamp,

position lamp, turn signal lamp

and fog lamp light bulb replace-

ment

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

Type A

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OLMB073042L

Headlamp and Static bending lamp

WARNING

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

OTL075064

(1) Headlamp (Low)

(2) Headlamp (High)

(3) Turn signal lamp

(4) Position lamp

• Wear eye protection when

changing a bulb. Allow the bulb

to cool down before handling it.

(5) Daytime running lamp

(6) Fog lamp

(7) Static bending lamp

(if equipped)

7-76

■ High/Low beam

5. Unsnap the bulb retaining wire by

pressing the end and pushing it

upward.

6. Remove the bulb from the head-

lamp assembly.

7. Install a new bulb and snap the

bulb retaining wire into position by

aligning the wire with the groove

on the bulb.

Low

High

8. Connect the bulb socket-connec-

tor.

OTLE075013

■ Static bending lamp

OTLE075019

9. Install the bulb cover by turning it

clockwise.

Turn signal lamp

1. Open the hood.

2. Disconnect the negative battery

cable.

i

Information

The headlamp aiming should be adjust-

ed after an accident or after the head-

lamp assembly is reinstalled at an

authorized HYUNDAI dealer.

3.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

7

OTLE075015

1. Open the hood.

4.Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

2. Disconnect the negative battery

cable.

3. Remove the bulb cover by turning

it counterclockwise.

4. Disconnect the bulb socket-con-

nector.

7-77

Maintenance

■ Halogen bulb

5.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

Type B

6.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

Position lamp/Daytime running

lamp/Fog lamp

OLMB073042L

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

Headlamp (High beam)

OTL075032

(1) Headlamp (Low)

(2) Headlamp (High)

(3) Turn signal lamp

(4) Position lamp

WARNING

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

(5) Daytime running lamp

(6) Fog lamp

(7) Static bending lamp

• Wear eye protection when

changing a bulb. Allow the bulb

to cool down before handling it.

7-78

■ High beam

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

6. Remove the bulb from the head-

lamp assembly.

7. Install a new bulb and snap the

bulb retaining wire into position by

aligning the wire with the groove

on the bulb.

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

8. Connect the bulb socket-connec-

tor.

• A bulb should be operated only

when installed in a headlamp.

9. Install the bulb cover by turning it

clockwise.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OTLE075014

1. Open the hood.

2. Disconnect the negative battery

cable.

3. Remove the bulb cover by turning

it counterclockwise.

4. Disconnect the bulb socket-con-

nector.

7

5. Unsnap the bulb retaining wire by

pressing the end and pushing it

upward.

7-79

Maintenance

Headlamp (Low, LED type)

5.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

6.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

i

Information

The headlamp aiming should be adjust-

ed after an accident or after the head-

lamp assembly is reinstalled at an

authorized HYUNDAI dealer.

Position lamp/ Daytime running lamp/

Fog lamp/Static bending lamp

OTLE075019

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

Turn signal lamp

1. Open the hood.

2. Disconnect the negative battery

cable.

3.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7-80

7.Connect the bulb electrical con-

nector.

Type B

Side repeater lamp replace-

ment

8.Reinstall the lamp assembly to the

body of the vehicle.

Type A

OTL075065

1.Remove the lamp assembly from

the vehicle by prying the lens and

pulling the assembly out.

OTL075066

If the light bulb does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

2.Disconnect the bulb electrical con-

nector.

3.Separate the socket and the lens

parts by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots on the

lens part.

7

4.Remove the bulb by pulling it

straight out.

5.Insert a new bulb in the socket.

6.Reassemble the socket and the

lens part.

7-81

Maintenance

4. With the headlamp and battery in

normal condition, aim the head-

lamps so the brightest portion falls

on the horizontal and vertical

lines.

Front fog lamp aiming

Headlamp and front fog lamp

aiming (for Europe)

Headlamp aiming

5. To aim the low beam left or right,

turn the driver clockwise or coun-

terclockwise. To aim the low beam

up or down, turn the driver clock-

wise or counterclockwise.

To aim the high beam up or down,

turn the driver clockwise or coun-

terclockwise.

OTLE075021

The front fog lamp can be aimed as

the same manner of the headlamps

aiming.

OTLE075020

1. Inflate the tires to the specified

pressure and remove any loads

from the vehicle except the driver,

spare tire, and tools.

With the front fog lamps and battery

in normal condition, aim the front fog

lamps.

To aim the front fog lamp up or down,

turn the driver clockwise or counter-

clockwise.

2. The vehicle should be placed on a

flat floor.

3. Draw vertical lines (Vertical lines

passing through respective head

lamp centers) and a horizontal line

(Horizontal line passing through

center of head lamps) on the

screen.

7-82

Aiming point

H1 : Height between the head lamp bulb center and ground (Low beam)

H2 : Height between the head lamp bulb center and ground (High beam)

H3 : Height between the fog lamp bulb center and ground

W1 : Distance between the two head lamp bulbs centers (Low beam)

W2 : Distance between the two head lamp bulbs centers (High beam)

W3 : Distance between the two fog lamp bulbs centers

7

OTLE075022

Unit: mm (in)

H3

FOG+DRL

W3

Vehicle

condition

Lamp type

H1

H2

W1

W2

FOG

FOG+DRL

Halogen/HID 886 (34.89)

LED 884 (34.80)

Halogen/HID 879 (34.60)

LED 877 (34.53)

1502 (59.13)

1494 (58.82)

1502 (59.13)

1494 (58.82)

862

(33.94)

578

(22.76)

Without driver

With driver

565 (22.24)

558 (21.97)

1208 (47.56) 1474 (58.03) 1452 (57.17)

855

(33.66)

571

(22.48)

1208 (47.56) 1474 (58.03) 1452 (57.17)

7-83

Maintenance

Headlamp low beam (LHD side)

■ Based on 10m screen

OTLE075100

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If headlamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

7-84

Headlamp low beam (RHD side)

■ Based on 10m screen

7

OTLE075101

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If headlamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

7-85

Maintenance

Front fog lamp

■ Based on 10m screen

OTLE075102

1. Turn the front fog lamp on without the driver aboard.

2. The cut-off line should be projected in the allowable range (shaded region).

7-86

3. Loosen the lamp assembly retain-

ing screws with a cross-tip screw-

driver.

Outside lamp

Rear combination light bulb

replacement

Stop/tail Lamp and Turn signal

lamp

■ Type A

4. Remove the rear combination

lamp assembly from the body of

the vehicle.

OTL075034

■ Type B

OTL075035

7

OTL075034

OTL075036

(1) Stop lamp

1. Turn off the engine.

2. Open the tailgate.

(2) Tail lamp

(3) Rear turn signal lamp

(4) Back-up lamp

7-87

Maintenance

8.Install the socket in the assembly by Stop/tail lamp (LED type)

aligning the tabs on the socket with

the slots in the assembly.

Push the socket into the assembly checked by an authorized HYUNDAI

If the LED lamp does not operate, we

recommend you to have the vehicle

Stop/tail lamp

and turn the socket clockwise.

dealer.

9.Reinstall the lamp assembly to the

body of the vehicle.

Turn Signal lamp

OTL075037

5.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on the

assembly.

6.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

7-88

Stop and tail lamp (LED type)

Inside lamp

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

Tail lamp/Back-up lamp

OTL075039

4.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OTLE075016

1. Turn off the engine.

2. Open the tailgate.

5.Pull the bulb out of the socket.

6.Insert a new bulb into the socket.

3. Remove the service cover using a

flat-blade screwdriver.

7.Install the socket into the assembly

by aligning the tabs on the socket

with the slots on the assembly and

turning the socket clockwise.

7

8.Reinstall the lamp assembly to the

body of the vehicle

7-89

Maintenance

Rear fog lamp (if equipped)

High mounted stop lamp

replacement

License plate light bulb

replacement

1.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

2.Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

3.Insert a new bulb in the socket.

OTL075040

OTL075041

4.Reinstall the light assembly to the

body of the vehicle.

If the high mounted stop lamp does not 1.Loosen the lens retaining screws

operate, we recommend that you con-

tact an authorized HYUNDAI dealer.

with a screwdriver.

2.Remove the lens.

3.Remove the bulb by pulling it straight

out.

4.Install a new bulb.

5.Reinstall the lens securely with the

lens retaining screws.

7-90

Interior light bulb replacement

Map lamp, Room lamp, Vanity mirror lamp, Tailgate room lamp and

glove box lamp

Map lamp and Room lamp

■ Map lamp - with sunroof

■ Map lamp - without sunroof

■ Vanity mirror lamp

OTLE075017

OTLE075018

OTL075043

■ Room lamp - with sunroof

■ Room lamp - without sunroof

■ Tailgate room lamp

7

OTL075044

OLFH074029

OTL075045

If the LED lamp does not operate, we

recommend you to have the vehicle

checked by an authorized HYUNDAI

dealer.

7-91

Maintenance

■ Glove box lamp

NOTICE

Be careful not to damage the cover,

tab, and plastic housing.

OTL075046

1. Using a flat-head screwdriver,

gently pry the lens from the interi-

or light housing.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior

light housing notches and snap

the lens into place.

7-92

Maintenance -> Light bulbs for Your Hyundai Tucson SUV Third Generation (2016-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals