Get Maintenance -> Light bulbs Guide for Kia Picanto 4 Door Third Generation (2019-2026)

Maintenance

Light bulbs

Relay [(Petrol) 1.0 FFV]

Light bulbs

Bulb replacement precaution

Symbol

Relay Name

Type

Please prepare bulbs with appropriate

Main Relay

MINI

standards in case of emergencies. Refer

to "Bulb wattage" on page 9-4. When

Air Conditioner Relay

MICRO

changing bulbs and sorts, first turn off

HIGH CURRENT

Start Relay

MICRO

the engine at a safe place, firmly apply

HIGH CURRENT

the side brake and take out the battery's

Blower Relay

MICRO

negative (-) terminal.

Horn Relay

MICRO

WARNING

Burglar Alarm Horn

MICRO

Relay

Working on the lights

HIGH CURRENT

Cooling Fan Relay

Prior to working on the light, firmly apply

MICRO

the parking brake, ensure that the igni-

HIGH CURRENT

Head Lamp Low Relay

MICRO

tion switch is turned to the LOCK posi-

tion and turn off the lights to avoid

Head Lamp High Relay

MICRO

sudden movement of the vehicle and

Sub Fuel Pump Relay

MICRO

burning your fingers or receiving an

electric shock.

Fuel Pump Relay

MICRO

Use only the bulbs of the specified watt-

age.

WARNING

Be sure to replace the burnedout bulb

with one of the same wattage rating.

Otherwise, it may cause extensive wiring

damage and possible fire.

CAUTION

If you don't have necessary tools, the

correct bulbs and the expertise, consult

a professional workshop. Kia recom-

mends to consult an authorised Kia

dealer/service partner.

Maintenance

Light bulbs

In many cases, it is difficult to replace

to normal, the vehicle does not

vehicle light bulbs because other parts

require service.

of the vehicle must be removed before

However, if the lamp goes out after he

you can get to the is especially

momentary flickering, or the flickering

true if you have to remove the headlight

continues, have the system serviced

assembly to get to the bulb(s). Remov-

by a professional workshop. Kia rec-

ing/ installing the headlight assembly

ommends to visit an authorised Kia

can result in damage to the vehicle.

dealer/service partner.

NOTICE

CAUTION

僅 If the light bulb or lamp connector is

僅 If unauthentic parts or substandard

removed from an operating lamp acti-

lights are used when changing lights,

vated by electricity, the fuse box’s

it may lead to fuse disconnection and

electronic device may scan it as a

malfunction, and other wiring dam-

malfunction. Therefore, a lamp mal-

ages.

function history may be recorded in

僅 Do not install extra lamps or LED to

Diagnostic Trouble Code (DTC) in the

the vehicle. If supplementary lights

fuse box.

are installed, it may lead to lamp mal-

僅 It is normal for an operating lamp may

function and flickering of the lights. In

blink temporarily. Since this occur-

addition, the fuse box and other writ-

rence is due stabilization function of

ing may be damaged.

the vehicle’s electronic control device,

if the lamp lights up normally after

僅 Lamp part malfunction due to net-

temporary blinking, there is no prob-

work failure

lem in the vehicle. However, if the

The headlamp, taillight, and fog light

lamp continues to blink several times

may lit up when the head lamp switch

or turn off completely, there may be

is turned ON, and not light up when

an error in the vehicle’s electronic

the taillight or for light switch is turned

control device. In this case, have the

ON. This may be cause by network

vehicle checked by a professional

failure or vehicle electrical control sys-

workshop immediately. Kia recom-

tem malfunction. If there is a problem,

mends to visit an authorised Kia

have the system serviced by a profes-

dealer/service partner.

sional workshop. Kia recommends to

visit an authorised Kia dealer/service

NOTICE

partner.

After an accident or after the headlight

僅 Lamp part malfunction due to elec-

assembly is reinstalled, have the head-

trical control system stabilization

light aiming adjusted by a professional

A normally functioning lamp may

workshop. Kia recommends to visit an

flicker momentarily. This momentary

authorised Kia dealer/service partner.

occurrence is due to stabilization unc-

tion of the vehicle's electrical on con-

trol system. If the lamp soon returns

Maintenance

Light bulbs

Daytime running lamp

NOTICE

You can find moisture inside the lens of

lamps after a car wash or driving in the

rain. It is a natural event caused by the

temperature difference between the

inside and the outside of the lamp and

does not mean a problem with its func-

OJAPE073030

tions. The moisture inside the lamp

1. Headlamp (High/Low) (Bulb type)

would disappear if you drive the vehicle

2. Headlamp (High/Low) (LED type)

with the headlamp turned on, however,

3. Position lamp / Daytime running lamp

the level at which the moisture is

(Bulb type)

removed may differ depending on the

size / location / condition of the lamp. If

4. Position lamp / Daytime running lamp

the moisture continues to stay inside the

(LED type)

lamp, have the vehicle checked by a

5. Front turn signal lamp (Bulb type)

professional workshop. Kia recommends

6. Front turn signal lamp (LED type)

to visit an authorised Kia dealer/service

7. Daytime running lamp (LED type)

partner.

Light bulb position (Rear)

Light bulb position (Front)

Rear combination lamp – Type A

Headlamp – Type A

OJAPE073031

Rear combination lamp – Type B

OJAPE073028

Headlamp – Type B

OJAPE073032

OJAPE073029

$MaintenanceLight bulbsReplacing lights (LED type)Back up lamp/ License plate lamp /High mounted stop lampIf the LED lamp does not operate, haveyour vehicle checked by a professionalworkshop. Kia recommends to visit anauthorised Kia dealer/service LED lamp cannot be replaced as asingle unit because it is an integratedunit. The LED lamp has to be replacedOJAPE073033with the unit.1. Stop and tail lamp (Bulb type)A skilled technician should check or2. Tail lamp (LED type)repair the LED lamp, for it may damage3. Rear turn signal lamp (Bulb type)related parts of the vehicle.4. Stop lamp (LED type)Headlamp (Low/High beam) bulb5. Back up lamp (Bulb type)/ Rear fogreplacement (Headlamp Type A)lamp (LED type)6. High mounted stop lamp (Bulb type)7. License plate lamp (Bulb type)Light bulb position (Side)Type AOJAPE0730341. Apply the parking brake and turn theignition to "OFF".2. Turn off the lights.3. Open the bonnet.4. Remove the headlamp bulb cover byOJAPE073037turning it B5. Disconnect the headlamp bulbsocket-connector.6. Unsnap the headlamp bulb retainingwire by pressing the end and pushingit upward.7. Remove the bulb from the head lampOJAPE073041assembly.1. Side repeater lamp (Bulb type)8. Install in reverse order of removal.2. Side repeater lamp (LED type)866$

Maintenance

Light bulbs

Replacing lights (LED type)

Back up lamp/ License plate lamp /

High mounted stop lamp

If the LED lamp does not operate, have

your vehicle checked by a professional

workshop. Kia recommends to visit an

authorised Kia dealer/service partner.

The LED lamp cannot be replaced as a

single unit because it is an integrated

unit. The LED lamp has to be replaced

OJAPE073033

with the unit.

1. Stop and tail lamp (Bulb type)

A skilled technician should check or

2. Tail lamp (LED type)

repair the LED lamp, for it may damage

3. Rear turn signal lamp (Bulb type)

related parts of the vehicle.

4. Stop lamp (LED type)

Headlamp (Low/High beam) bulb

5. Back up lamp (Bulb type)/ Rear fog

replacement (Headlamp Type A)

lamp (LED type)

6. High mounted stop lamp (Bulb type)

7. License plate lamp (Bulb type)

Light bulb position (Side)

Type A

OJAPE073034

1. Apply the parking brake and turn the

ignition to "OFF".

2. Turn off the lights.

3. Open the bonnet.

4. Remove the headlamp bulb cover by

OJAPE073037

turning it counterclockwise.

Type B

5. Disconnect the headlamp bulb

socket-connector.

6. Unsnap the headlamp bulb retaining

wire by pressing the end and pushing

it upward.

7. Remove the bulb from the head lamp

OJAPE073041

assembly.

1. Side repeater lamp (Bulb type)

8. Install in reverse order of removal.

2. Side repeater lamp (LED type)

Maintenance

Light bulbs

Headlamp bulb

3. Open the bonnet and remove the turn

signal lamp assembly by turning it

counterclockwise.

4. Remove the bulb by turning it coun-

terclockwise and Install a new bulb.

5. Install in reverse order of removal.

Position lamp/Daytime running

OJAPE073025

lamp (Bulb type) bulb replace-

WARNING

ment (Headlamp Type A)

Halogen bulbs

Headlamp Type A

僅 Halogen bulbs contain pressurized

gas that will produce flying pieces of

glass if broken.

僅 Always handle them carefully, and

avoid scratches and abrasions. If the

bulbs are lit, avoid contact with liq-

uids. Never touch the glass with bare

OJAPE073036

hands. Residual oil may cause the

1. Apply the parking brake and turn the

bulb to overheat and burst when lit.

ignition to "OFF".

A bulb should be operated only when

2. Turn off the lights.

installed in a headlight.

3. Open the bonnet and remove the

僅 If a bulb becomes damaged or

Position & Daytime Running Lamp

cracked, replace it immediately and

assembly by turning it counterclock-

carefully dispose of it.

wise.

僅 Wear eye protection when changing a

4. Install a new bulb and Install in

bulb. Allow the bulb to cool down

reverse order of removal.

before handling it.

Rear turn signal lamp (Bulb type)

bulb replacement (Rear combina-

Front turn signal lamp (Bulb type)

tion lamp Type A)

bulb replacement (Headlamp

Type A)

1. Apply the parking brake and turn the

ignition to "OFF".

2. Turn off the lights.

3. Open the tailgate.

4. Loosen the light assembly retaining

screws with a cross-tip screwdriver.

5. Remove the rear combination lamp

OJAPE073035

assembly from the body of the vehi-

1. Apply the parking brake and turn the

cle.

ignition to "OFF".

2. Turn off the lights.

$MaintenanceLight bulbsTail lamp (Bulb type) bulb6. Disconnect the rear combination (Rear combinationlamp Type A)1. Apply the parking brake and turn theignition to "OFF".2. Turn off the lights.3. Open the tailgate.4. Loosen the light assembly retainingOJAPE073039screws with a cross-tip screwdriver.5. Remove the rear combination lampassembly from the body of the vehi-cle.6. Disconnect the rear combination 0730407. Remove the socket from the assemblyby turning the socket counterclock-wise until the tabs on the socket alignwith the slots on the assembly.8. Remove the bulb from the socket bypressing it in and rotating it counter-OJAPE073039clockwise until the tabs on the bulbalign with the slots in the socket. Pullthe bulb out of the 0730407. Remove the socket from the assemblyby turning the socket counterclock-OJAPE073048wise until the tabs on the socket align9. Insert a new bulb by inserting it intowith the slots on the socket and rotating it until it locks8. Remove the bulb from the socket byinto it in and rotating it the socket in the assembly byclockwise until the tabs on the bulbaligning the tabs on the socket withalign with the slots in the slots in the assembly. Push thesocket into the assembly and turn thesocket clockwise.11.Install the rear combination lampassembly to the body of the 073049L868$

Maintenance

Light bulbs

Tail lamp (Bulb type) bulb

6. Disconnect the rear combination lamp

connector.

replacement (Rear combination

lamp Type A)

1. Apply the parking brake and turn the

ignition to "OFF".

2. Turn off the lights.

3. Open the tailgate.

4. Loosen the light assembly retaining

OJAPE073039

screws with a cross-tip screwdriver.

5. Remove the rear combination lamp

assembly from the body of the vehi-

cle.

6. Disconnect the rear combination lamp

connector.

OJAPE073040

7. Remove the socket from the assembly

by turning the socket counterclock-

wise until the tabs on the socket align

with the slots on the assembly.

8. Remove the bulb from the socket by

pressing it in and rotating it counter-

OJAPE073039

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

OJAPE073040

7. Remove the socket from the assembly

by turning the socket counterclock-

OJAPE073048

wise until the tabs on the socket align

9. Insert a new bulb by inserting it into

with the slots on the assembly.

the socket and rotating it until it locks

8. Remove the bulb from the socket by

into place.

pressing it in and rotating it counter-

10.Install the socket in the assembly by

clockwise until the tabs on the bulb

aligning the tabs on the socket with

align with the slots in the socket.

the slots in the assembly. Push the

socket into the assembly and turn the

socket clockwise.

11.Install the rear combination lamp

assembly to the body of the vehicle.

OJAPE073049L

Maintenance

Light bulbs

9. Insert a new bulb by inserting it into

wise until the tabs on the socket align

the socket and rotating it until it locks

with the slots on the assembly.

into place.

5. Remove the bulb from bulb-socket by

10.Install the socket in the assembly by

pulling it out.

aligning the tabs on the socket with

6. Insert a new bulb by inserting it into

the slots in the assembly. Push the

the bulb-socket.

socket into the assembly and turn the

7. Install the socket in the assembly by

socket clockwise.

aligning the tabs on the socket with

11.Install the rear combination lamp

the slots in the assembly. Push the

assembly to the body of the vehicle.

socket into the assembly and turn the

socket clockwise.

Back up lamp (Bulb type) bulb

8. Align the lens cover tabs with the

replacement

lamp housing notches and snap the

lens into place.

High mounted stop lamp (Bulb

type) bulb replacement

OJAPE073051

If the back up lamp does not operate,

have your vehicle checked by a profes-

sional workshop. Kia recommends to

OJAPE073042

visit an authorised Kia dealer/service

If the high mounted stop lamp (1) does

partner.

not operate, have your vehicle checked

License plate lamp (Bulb type)

by a professional workshop. Kia recom-

bulb replacement

mends to visit an authorised Kia dealer/

service partner.

Side repeater lamp (bulb type)

bulb replacement

OJAPE073043

1. Apply the parking brake and turn the

ignition to "OFF".

2. Turn off the lights.

OJAPE073044

3. Using a flat-blade screwdriver, gently

1. Apply the parking brake and turn the

pry the lens cover from lamp housing.

ignition to "OFF".

4. Remove the socket from the assembly

2. Turn off the lights.

by turning the socket counterclock-

3. Remove the lens by pulling it forward

from the vehicle.

Maintenance

Light bulbs

Room lamp (Bulb type) bulb

4. Disconnect the bulb connector.

replacement

5. Remove the bulb socket from the

body by turning it counterclockwise.

6. Install a new bulb and install in the

reverse order of removal.

Map lamp (Bulb type) bulb

replacement

OJAPE073046

1. Apply the parking brake and turn the

ignition to "OFF".

2. Turn off the lights.

3. Using a flat-blade screwdriver, gently

pry the lens cover from lamp housing.

OJAPE073045

4. Remove the bulb by pulling it straight

1. Apply the parking brake and turn the

out.

ignition to "OFF".

5. Install a new bulb in the socket.

2. Turn off the lights.

6. Align the lens cover tabs with the

3. Using a flat-blade screwdriver, gently

lamp housing notches and snap the

pry the lens cover from lamp housing.

lens into place.

4. Remove the bulb by pulling it straight

WARNING

out.

5. Install a new bulb in the socket.

Prior to working on the Interior lamps,

6. Align the lens cover tabs with the

ensure that the “OFF” button is

lamp housing notches and snap the

depressed to avoid burning your fingers

lens into place.

or receiving an electric shock.

WARNING

CAUTION

Prior to working on the Interior lamps,

Be careful not to dirty or damage the

ensure that the “OFF” button is

lens, lens tab, and plastic housings.

depressed to avoid burning your fingers

or receiving an electric shock.

CAUTION

Be careful not to dirty or damage the

lens, lens tab, and plastic housings.

Maintenance

Light bulbs

Vanity mirror lamp (LED type)

CAUTION

bulb replacement

Be careful not to dirty or damage the

lens, lens tab, and plastic housings.

Headlamp and front fog lamp

aiming (for Europe)

Headlamp aiming

OJAPE073144R

Type A

If the vanity mirror lamp (LED type) (1)

does not operate, have your vehicle

checked by a professional workshop. Kia

recommends to visit an authorised Kia

dealer/service LED lamp

cannot be replaced as a single compo-

nent because it is an integrated unit. The

LED lamp has to be replaced with the

unit.A skilled technician should check or

repair the vanity mirror lamp (LED type),

for it may damage related parts of the

vehicle.

OJAPE073106L

Tailgate room lamp (Bulb type)

Type B

bulb replacement

OJAPE073047

1. Apply the parking brake and turn the

ignition to "OFF".

2. Turn off the lights.

3. Using a flat-blade screwdriver, gently

OJAPE073107L

pry the lens cover from lamp housing.

1. Inflate the tyres to the specified pres-

4. Remove the bulb by pulling it straight

sure and remove any loads from the

out.

vehicle except the driver, spare tyre,

5. Install a new bulb in the socket.

and tools.

6. Align the lens cover tabs with the

2. The vehicle should be placed on a flat

lamp housing notches and snap the

floor.

lens into place.

Maintenance -> Light bulbs for Your Kia Picanto 4 Door Third Generation (2019-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals