Get Features of your vehicle -> Mirrors Guide for Kia Sportage SUV Fifth Generation (2022-2026)

Features of your vehicle

Mirrors

For Kia Connect button function

Mirrors

This vehicle is equipped with inside and

outside rear view mirrors to provide

views of objects behind the vehicle.

Inside rear view mirror

Adjust the rear view mirror so that the

center view through the rear window is

seen. Make this adjustment before you

start driving.

ONQ5031538N

1. Roadside Assistance button

2. SOS button

Do not place objects in the rear seat or

cargo area which would interfere with

your vision out the rear window.

Day/night rear view mirror (if

equipped)

WARNING

4

Mirror adjustment

Do not adjust the rear view mirror while

the vehicle is moving. This could result in

loss of control.

OCV041036L

(A): Day, (B): Night

NOTICE

Make this adjustment before you start

driving and while the day/night lever is

in the day position (1).

Do not modify the inside mirror in any

manner, including installing a wide mir

ror. Doing so could result in injury during

an accident or deployment of the air

bag.

-

Pull the day/night lever toward you (2) to

reduce the glare from the headlamps of

the vehicles behind you during night

driving.

CAUTION

Remember that you lose some rear view

clarity in the night position.

Cleaning mirror

When cleaning the mirror, use a paper

towel or similar material dampened with

glass cleaner. Do not spray glass cleaner

directly on the mirror. It may cause the

Electric chromic mirror (ECM)

with HomeLink씾 system (if

equipped)

Electric Chromic Mirror (ECM) is that

controls the glare from the headlamps of

the vehicles behind you in nighttime or

low light driving conditions.

liquid cleaner to enter the mirror hous

ing.

-

The sensor mounted in the mirror

senses the light level around the vehicle,

and automatically controls the head

-

lamp glare from the vehicles behind you.

4

51

Features of your vehicle

Mirrors

When the engine is running, the glare is

automatically controlled by the sensor

mounted in the rear view mirror.

Your mirror will automatically dim upon

detecting glare from the vehicles travel

-

ing behind you.

The mirror defaults to the ON position

each time the vehicle is started.

Integrated HomeLink씾 Wireless

Control System

The HomeLink씾 Wireless Control Sys

-

OCV041602N

1. HomeLink Channel 1

2. HomeLink Channel 2

3. HomeLink Channel 3

tem provides a convenient way to

replace up to three handheld radio-fre

quency (RF) transmitters used to acti

vate compatible devices such as gate

operators, garage door openers, entry

-

4. Garage Door Opener Status Indicator:

Closing or Closed

door locks, security systems, and home

lighting.

5. HomeLink Operation Indicator

NOTICE

6. Garage Door Opener Status Indicator:

Opening or Opened

Considering the Home Security when

the vehicle is parked outside the garage,

the HomeLink will ONLY work when the

ignition switch is in ACC position or ON

position.

7. HomeLink User Interface Indicator

Your vehicle may be equipped with a

Gentex Automatic-Dimming Mirror with

an Integrated HomeLink씾 Wireless Con

-

trol System.

CAUTION

During nighttime driving, this feature will

automatically detect and reduce rear

Before programming HomeLink to a

garage door opener or gate operator,

make sure that people and objects are

out of the way of the device to prevent

view mirror glare. The HomeLink씾 Uni

-

versal Transceiver allows you to activate

your garage door(s), electric gate, home

lighting, etc.

potential harm or damage. When pro

-

gramming a garage door opener, it is

advised to park outside of the garage.

Automatic-Dimming Night Vision

Safety™ (NVS씾) Mirror (if

equipped)

Do not use HomeLink with any garage

door opener that lacks safety stop and

reverse features as required by U.S. fed

eral safety standards (this includes any

The NVS씾 Mirror automatically reduces

glare by monitoring light levels in the

front and the rear of the vehicle. Any

objects that obstructs the light sensor

will degrade the automatic dimming

control feature.

-

garage door opener model manufac

tured before April 1, 1982). A garage

-

door that cannot detect an object signal

ing the door to stop and reverse - does

not meet current U.S. federal safety

-

For more information regarding NVS씾

mirrors and other applications, please

refer to the Gentex website:

www.gentex.com

standards. For more information, con

-

tact HomeLink at www.homelink.com

,

4

52

Features of your vehicle

Mirrors

or call HomeLink customer support at 1-

to HomeLink for quicker training and

accurate transmission of the radio-

frequency signal.

800-355-3515

.

It is also recommended that a new bat

-

tery be replaced in the hand-held trans

mitter of the device being trained to

-

3. Place the ignition switch or ENGINE

START/STOP button to the ACC

HomeLink for quicker training and accu

-

(Accessory) position for program

-

rate transmission of the radio frequency.

ming of HomeLink.

1. Programming HomeLink씾

The following steps show how to pro

-

gram HomeLink. If you have any ques

-

tions or are having difficulty

programming your HomeLink buttons,

refer to the HomeLink website or call the

HomeLink customer support toll-free

number. Do this, before going back to

the dealer who sold you the car.

OCV041603N

4

2) Programming a New Home

Link씾 Button

-

1. Press and release the HomeLink but

ton ((1), (2) or (3)) you would like to

-

僅 Visit the HomeLink website at:

www.homelink.com. Then at the top

of the page, choose your vehicle

make. Then watch the You Tube

program. If successful, the HomeLink

indicator light (7) will flash orange

slowly. If the HomeLink indicator light

does not blink orange slowly, then

start over and perform the steps of

"Erasing Home- Link Buttons" section

again.

video, and/or access additional web

site information.

-

僅 If you choose to access the website

via your cell phone, scan the QR code.

僅 Or, call HomeLink customer support

at 1-800-355-3515

OCV041604N

(Please have the vehicle make/model

AND the opener device make/model

readily available.)

2. Position the garage door opener

remote 1 - 3 inches (2 - 8 cm) away

from the HomeLink buttons.

1) Programming Preparation

1. When programming a garage door

opener, it is advised to park the vehi

cle outside of the garage.

-

2. It is recommended that a new battery

be placed in the hand-held transmit

ter of the device being programmed

OCV041605N

-

4

53

Features of your vehicle

Mirrors

3. While the HomeLink indicator light (7)

is flashing orange, press and hold the

hand-held remote button. Continue

pressing the hand-held remote button

until the HomeLink indicator light (7)

light changes from orange to green.

You may now release the hand-held

remote button.

4. Wait until your garage door comes to

a complete stop, regardless of posi

tion, before proceeding to the next

steps.

-

ODL3A040504

5. Press and release the HomeLink but

ton you are programming and

observe the indicator light.

-

* A ladder and/or second person may

simplify the following steps.

7. Firmly press and release the "Learn"

,"Smart", "Set" or "Program"" button.

You now have up to 30 seconds in

which to complete the next step.

僅 If the indicator light remains solid

green, your device should operate

when the HomeLink button is

pressed. At this point, if your device

8. Return to the vehicle and firmly press,

hold for two seconds and release, the

HomeLink button up to three times in

operates, programming is com

-

plete.

僅 If the indicator light rapidly flashes

green, firmly press, hold for two

seconds and release the HomeLink

button up to three times in a row

a row slowly. Do not press the Home

Link button rapidly. As soon as you

see the garage door start to move,

stop pressing any buttons until a few

seconds after the garage door has

come to a complete stop, regardless

of position. At this point programming

is complete and your device should

operate when the HomeLink button is

pressed and released.

-

slowly to complete the program

-

ming process. Do not press the

HomeLink button rapidly. At this

point if your device operates, pro

-

gramming is complete. If the device

does not operate, continue with

step 6.

6. At the garage door opener motor,

(security gate motor, etc.) locate the

"Learn", "Smart", "Set" or "Program"

button. This can usually be found

where the hanging antenna wire is

attached to the motor-head unit (see

the device's manual to identify this

button). The name and color of the

button may vary by manufacturer.

3) Two-Way Communication Pro

gramming (For select garage

door openers)

-

If your garage door opener has the

'myQ' logo on its side, your opener has

Two-Way Communication capability.

HomeLink has the capability to establish

Two-Way Communication with your

garage door opener. HomeLink can

receive and display "closing" or "open

-

ing" status messages from compatible

4

54

Features of your vehicle

Mirrors

garage door openers. At any time,

5. Return to the vehicle and firmly press

HomeLink can also recall and display the

last recorded status communicated by

the garage door opener to indicate your

garage door being "closed" or "opened".

and release the programmed Home

Link button to activate your garage

-

door. The Two-Way Communication

indicators (4), (6) flash in orange

when the door is moving. Do not

make any additional button presses

until AFTER the garage door has

come to a complete stop.

To check if your garage door opener is

compatible with this feature, refer to

www.homelink.com/compatible/Two-

way-Communication. If your garage

door opener has this functionality, AND

the Two-Way Communication indicators

(4), (6) in the mirror appear while the

garage door is opening/closing, then no

further steps are needed. Two-Way

Communication Programming is already

complete. However, if your garage door

opener has this functionality, AND the

Two-Way Communication indicators (4),

(6) in the mirror DO NOT appear while

the garage door is opening/closing, use

the following instructions to enable this

functionality.

6. Your Two-Way Communication pro

-

gramming is now complete.

NOTICE

If your garage door opener has Two-

Way Communication functionality, it is

possible for HomeLink to stop function

ing the garage door shortly after initial

programming, if the Two-Way Commu

nication Programming wasn't properly

completed. This usually happens after

4

-

the first 10 times a programmed Home

-

Link button is pressed. If you experience

this, completing the "Programming a

New HomeLink Button" and "Two-Way

Communication Programming" will

restore door operation.

1. In your vehicle, press and hold the

programmed HomeLink button for 2

seconds, then release. Confirm that

the garage door is moving. AFTER it

stops, you will have one minute to

complete the following steps:

4) Canadian Programming

* A ladder and/or second person may

simplify the following steps.

Canadian radio-frequency laws require

transmitter remote signals to "time-out"

(or quit) after a couple seconds of trans

mission, which may not be long enough

for HomeLink to pick up the signal

during programming.

2. On your garage door opener in your

garage, locate the "Learn" button

(usually near where the hanging

antenna wire is attached to the

-

garage door opener). If there is diffi

-

culty locating this button, refer to the

device's owner's manual.

If you live in Canada or you are having

difficulties programming a gate operator

or garage door opener by using the pro

gramming procedures, replace "Pro

gramming a New HomeLink Button"

step 3 with the following:

-

3. Press and release the "Learn" button.

4. A light on your garage door opener

-

may flash, and your Two-Way Com

-

munication indicators (4), (6) in your

vehicle may flash, confirming comple

tion of the process.

While the HomeLink indicator light (7) is

flashing orange, press and release

-

("cycle") your device's hand-held remote

4

55

Features of your vehicle

Mirrors

every two seconds until the HomeLink

indicator light (7) changes from orange

to green. You may now release the

hand-held remote button. Then proceed

with "Programming a New HomeLink

Button" step 4.

Two-Way Communication functional

ity.

-

2. Operating HomeLink씾

OCV041608N

1) Operating HomeLink씾

僅 If the indicator (4) flashes in

Orange, it indicates that the garage

door is "Closing".

1. Press and release the desired pro

grammed HomeLink button (1, 2 or 3).

-

僅 The indicator (4) turns solid green

once the garage door has closed.

僅 If the indicator (6) flashes in

Orange, it indicates that the garage

door is "Opening".

僅 The indicator (6) turns solid green

once the garage door has fully

opened.

OCV041604N

NOTICE

僅 If the indicator (4) or (6) does not

turn to green, it indicates that the

last status of garage door was not

received properly. The HomeLink

mirror tries to receive the last

known status of the garage door

for a few seconds.

The HomeLink indicator (7) should light

green, solid or flashing, and your pro

grammed device should operate.

-

If your device does not operate, the

HomeLink programming was not suc

-

cessful, and you'll need to reprogram the

button.

3) Recalling Garage Door Status

2) Two-Way Communication Dis

play Behavior

-

HomeLink mirror with Two-Way Com

-

munication provides a way to view the

last stored message from the garage

door opener. In order to recall the last

known status of the last activated

device, press the buttons "1 and 2" OR "2

and 3" simultaneously.

1. Press and release one of the pro

-

grammed HomeLink buttons (1, 2 or

3)

僅 If the indicator (4) appears solid

Green, it indicates that the last acti

-

vated device was properly "closed".

僅 If the indicator (6) appears solid

Green, it indicates that the last acti

OCV041607N

-

2. The indicator (4) and (6) operates as

below, if your garage door opener has

vated device was properly "open".

4

56

Features of your vehicle

Mirrors

4. Now all three HomeLink buttons (1),

3. Erasing HomeLink씾 Buttons

(2) and (3) are cleared of any pro

-

gramming

1) Erasing and Reprogramming a

Single HomeLink씾 Button:

Information

HomeLink and the HomeLink House

logo are registered trademarks of Gen

tex Corporation.

1. Press and hold the desired HomeLink

button you want to re-program. DO

NOT release the button.

-

The myQ logo is a registered trademark

of The Chamberlain Group, Inc

2. The HomeLink indicator light (7) will

begin appear solid green. Release the

button as soon as the HomeLink indi

-

cator light (7) begins to flash orange,

usually about 20 seconds.

FCC (USA) and ISED (Canada)

This device complies with FCC rules part

3. Proceed with the steps in the "Pro

-

15 and Innovation, Science, and Eco

-

gramming a New HomeLink Button"

section.

nomic Development Canada RSS-210.

Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) This device

must accept any interference that may

be received including interference that

may cause undesired operation. WARN

ING: The transmitter has been tested

and complies with FCC and ISED rules.

4

NOTICE

If you do not complete the re-program

-

ming of a new device to the button, it will

revert to the previously stored program

ming.

-

Changes or modifications not expressly

approved by the party responsible for

compliance could void the user's author

ity to operate the device.

2) The following instructions will

erase ALL HomeLink씾 program

ming from ALL buttons:

-

This equipment complies with FCC and

ISED radiation exposure limits set forth

for an uncontrolled environment. End

Users must follow the specific operating

instructions for satisfying RF exposure

compliance. This transmitter must be at

least 20 cm from the user and must not

OCV041609N_2

be co-located or operating in conjunc

tion with any other antenna or transmit

ter.

-

1. Press and hold the buttons (1) and (3)

simultaneously

-

2. The HomeLink indicator light (7) will

appear solid Orange for about 10 sec

-

onds

FCC (쉩tats-Unis) et ISED (Canada)

3. Release the buttons once the Home

Link indicator light (7) changes to

Green and flashes rapidly

-

Cet appareil est conforme aux r썟gle

-

ments de la FCC, section 15, et au CNR-

210 d'Innovation, Sciences et D썗veloppe

ment 썗conomique Canada. Le

-

4

57

Features of your vehicle

Mirrors

fonctionnement est assujetti aux deux

conditions suivantes: (1) cet appareil ne

doit pas causer d'interf썗rences nuisibles

et (2) cet appareil doit accepter toute

interf썗rence re썋ue, y compris celle qui

pourrait entra쎂ner un dysfonctionne

-

ment. MISE EN GARDE: L'썗metteur a

subi des tests et est conforme aux r썟gle

-

ments de la FCC et d'ISDE. Les change

-

ments ou modifications non approuv썗s

explicitement par la partie responsable

de la conformit썗 pourraient rendre

caduque l'autorisation de l'utilisateur de

se servir du dispositif.

Cet appareil est conforme aux limites

d'exposition aux radiations de la FCC et

d'ISDE 썗tablies pour un environnement

non contr쎦l썗. Les utilisateurs finaux

doivent respecter les instructions d'utili

-

sation sp썗cifiques pour satisfaire aux

exigences de conformit썗 aux expositions

de RF. L'썗metteur doit se trouver 쌽 20

cm au minimum de l'utilisateur et ne doit

pas 썛tre situ썗 au m썛me endroit que tout

autre 썗metteur ou antenne ni fonction

-

ner avec un autre 썗metteur ou antenne.

4

58

Features of your vehicle

Mirrors

HomeLink 5 Programing Flow Chart

4

59

Features of your vehicle

Mirrors

Outside rear view mirror

WARNING

Your vehicle is equipped with both left-

hand and right-hand outside rear view

mirrors.

Do not adjust or fold the outside rear

view mirrors while the vehicle is moving.

This could result in loss of control, and

an accident which could cause DEATH,

SERIOUS INJURY, or property damage.

Be sure to adjust the mirror angles

before driving.

The mirrors can be adjusted remotely

with the control levers or remote switch,

depending on the type of mirror control

installed. The mirror heads can be folded

Adjusting the outside rear view

mirrors

The electric remote control mirror switch

allows you to adjust the position of the

left and right outside rear view mirrors.

back to prevent damage during an auto

matic car wash or when passing through

a narrow street.

-

NOTICE

Rear view mirrors

僅 The outside rear view mirror is con

vex. Objects seen in the mirror are

closer than they appear.

-

ONQ5031026N

僅 Use your interior rear view mirror or

direct observation to determine the

actual distance of following vehicles

when changing lanes.

Adjusting the rear view mirrors:

1. Move the R or L switch (1) to select the

right side mirror or the left side mirror.

2. Press a corresponding point on the

mirror adjustment control (2) to posi

tion the selected mirror up, down, left

or right.

-

CAUTION

Do not scrape ice off the mirror face; this

may damage the surface of the glass. If

ice should restrict the movement of the

mirror, do not force the mirror for

adjustment. To remove ice, use a deicer

spray, or a sponge or soft cloth with

warm water.

CAUTION

僅 The mirrors stop moving when they

reach the maximum adjusting angles,

but the motor continues to operate

while the switch is pressed. Do not

press the switch longer than neces

-

sary, the motor may be damaged.

CAUTION

僅 Do not attempt to adjust the outside

rear view mirror glass by hand. You

may damage it.

If the mirror is jammed with ice, do not

adjust the mirror by force. Use an

approved spray de-icer (not radiator

antifreeze) to release the frozen mecha

nism or move the vehicle to a warm

place and allow the ice to melt.

-

4

60

Features of your vehicle

Mirrors

Folding the outside rear view mir

ror

-

Manual type

To fold the outside rear view mirror,

grasp the end of the mirror housing of

the mirror and pull it rearward and

inward.

ONQ5031027L

4

61

Features of your vehicle -> Mirrors for Your Kia Sportage SUV Fifth Generation (2022-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals