2006-2014 Nissan Qashqai SUV Instruments and controls -> Vehicle information display User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Vehicle information display for Your Nissan Qashqai SUV First Generation (2006-2014)

VEHICLE INFORMATION DISPLAY  
Gear shift indicator (where fitted), see  
(P. 5-16)  
j6  
Stop/Start system indicator (where fitted), see  
(P. 5-21)  
switch/shaft (Settings control and trip  
computer control)  
j7  
j8  
switch/shaft (Twin trip odometer control  
and brightness level control)  
WARNING  
Operating the vehicle information display  
while driving can lead to a crash resulting in  
serious injuries or death. Always park the ve-  
hicle in a safe place before operating the dis-  
play screen.  
•
•
Look at the display screen only briefly while  
driving. Keep your eyes on the road. Inatten-  
tive driving may lead to a crash resulting in  
serious injuries or death.  
NIC1645  
Outside temperature (P. 2-19)  
Clock (P. 2-19)  
Speed limiter (P. 5-31)  
j1  
j2  
j3  
Settings menu (P. 2-18)  
Intelligent Key operation (P. 2-6)  
Odometer (P. 2-16)  
Warnings and alerts (P. 2-12)  
Trip computer (P. 2-16)  
j4  
j5  
Engine oil level information (P. 2-15)  
Cruise control (P. 5-29)  
Twin trip odometer (P. 2-16)  
Instruments and controls 2-11  
Downloaded from manuals search engine  
WARNINGS AND ALERTS  
The design of the warnings and alerts may differ  
depending on the model.  
j1 Door open warning  
This warning appears if any of the doors are open or  
not closed securely. The vehicle icon indicates  
which door is open on the display.  
j2 Back door open warning  
This warning appears if the back door is open or not  
closed securely. When the door is to be left open,  
e.g. when you transport a long load, push the  
switch or the steering wheel switch ji (where fit-  
ted) to confirm.  
j3 Seat belt warning (Rear seat or 2nd  
row)  
The seat belt warning indicates the seating position  
when the ignition switch is turned to the ON position  
and disappears when:  
All related seat belts have been securely fas-  
tened.  
•
The  
switch or the steering wheel switch ji  
•
•
(where fitted) is pushed.  
Approximately 35 seconds after engine start.  
WARNING  
Seat belts for 3rd row seats (where fitted) are not  
part of the seat belt warning light monitoring sys-  
tem.  
NIC1644  
2-12 Instruments and controls  
Downloaded from manuals search engine  
For more information, see “Seat belts” in the  
“1. Safety — seats, seat belts and supplemental  
restraint system” section  
The emergency key can only be removed at  
the LOCK position. Make sure the ignition  
knob is in the LOCK position before removing  
the emergency key.  
•
j8 Intelligent Key detection warning  
If the Intelligent Key is taken outside of the vehicle  
ID recognition zone while the ignition knob is in the  
Acc or ON position, the Intelligent Key detection  
warning will be displayed and a buzzer will sound.  
The Intelligent Key detection warning disappears  
when the Intelligent Key is placed back in the pas-  
senger compartment.  
j4 Ignition knob warning (Intelligent Key  
models)  
See “Steering lock” in the “5. Starting and driving”  
section for further details.  
The warning appears when the ignition knob is left  
in the Acc or “OFF” position instead of completely  
being turned to the LOCK position.  
j5 Steering wheel lock warning  
The warning appears when the ignition knob is  
pressed, but not turned to the Acc or “OFF” posi-  
tion within a short period. Move the steering wheel  
to release the lock and turn the ignition knob to Acc  
or ON. The warning will turn off in approximately 5  
seconds.  
The message also appears when you try to start the  
vehicle if the Intelligent Key is not detected within  
the vehicle.  
If this warning appears, turn the ignition knob to the  
LOCK position.  
When the ignition knob is in the ON position, a  
buzzer will sound twice and the ignition knob warn-  
ing shows when the ignition knob is turned to the  
Acc or “OFF” position. This is to warn the driver that  
the ignition knob is not in the LOCK position.  
For more information, see “Integrated keyfob/re-  
mote control system” in the “3. Pre-driving checks  
and adjustments” section.  
See “Steering lock” in the “5. Starting and driving”  
section for further details.  
j9 Intelligent Key low battery warning  
MT models:  
j6 Brake/Clutch warning (where fitted)  
The Intelligent Key low battery warning may show if  
a low battery voltage is detected when the ignition  
knob is turned from “OFF” to the ON position.  
Depress the ignition PUSH release button and turn  
the ignition knob to the LOCK position.  
When starting your vehicle, it is necessary to oper-  
ate the brake (CVT and AT models) or clutch pedal  
(MT models).  
For more information, see “Integrated keyfob/Intel-  
ligent Key battery replacement” in the “8. Mainte-  
nance and do-it-yourself” section.  
AT or CVT models:  
For more information, see “Starting the engine” in  
the “5. Starting and driving” section.  
Make sure the gear selector lever is in the P (Park)  
position and then turn the ignition switch to the  
LOCK position.  
j10 Intelligent Key system fault warning  
CAUTION  
j7 Handbrake reminder  
See “Ignition knob (where fitted)” in the “5. Starting  
and driving” section for further details.  
The reminder will come on if the handbrake is on  
whilst the vehicle is being driven.  
If the Intelligent Key system fault warning comes  
on, it may indicate a system malfunction. We rec-  
ommend that you contact a NISSAN dealer or  
qualified workshop for repair.  
CAUTION  
A buzzer will also sound.  
The steering wheel can only be locked when  
•
the ignition knob is in the LOCK position. Make  
sure the ignition knob is in the LOCK position  
before leaving the vehicle.  
Instruments and controls 2-13  
Downloaded from manuals search engine  
For more information, see “Integrated keyfob/re-  
mote control system” in the “3. Pre-driving checks  
and adjustments” section.  
CAUTION  
j17 Diesel Particulate Filter warning  
(where fitted)  
The engine oil level check is not designed to indi-  
cate a low oil level. Use the dipstick to check the  
oil level.  
See “Diesel Particulate Filter (DPF) (where fitted)”  
in the “5. Starting and driving” section for further  
details.  
j11 Intelligent Key convenience mode alert  
The Intelligent Key convenience mode alert shows  
to confirm that convenience mode has been acti-  
vated. See “Switching from Convenience mode to  
Anti-hijack mode” in the “3. Pre-driving checks and  
adjustments” section.  
See “Engine oil” in the “8. Maintenance and  
do-it-yourself” section.  
j18 Setting menu operation alert  
The alert shows when you try to operate the setting  
menu while driving. The setting menu can only be  
entered if the vehicle is stationary.  
j14 Engine oil level  
This display provides a visual representation of the  
engine oil level.  
j12 Intelligent Key anti–hijack alert  
j19 Maintenance due alert (where fitted)  
j15 Engine oil level low  
The Intelligent Key anti–hijack alert shows to con-  
firm that anti-hijack mode has been activated. See  
“Switching from Convenience mode to Anti-hijack  
mode” in the “3. Pre-driving checks and  
adjustments” section.  
This alert shows that maintenance is due. The mes-  
sage is shown until the steering wheel switch ji  
(where fitted) is pressed. When the maintenance  
due alert reaches 0 km (miles), the  
flashes next to the odometer value.  
If the oil level is not sufficient for driving, the [Oil  
level low] message appears. Oil needs to be added  
before driving.  
symbol  
CAUTION  
j13 Engine oil level information  
When turning the ignition to the ON position, the oil  
message indicates the oil level.  
The engine oil level should be checked regularly.  
Operating with an insufficient amount of oil can  
damage the engine and such damage is not cov-  
ered by the warranty.  
CAUTION  
The engine oil must be changed before the main-  
tenance due alert is shown.  
The [Oil level OK] message indicates the oil level is  
sufficient for driving. Push the  
steering wheel switch ji (where fitted) when the  
[Oil level OK] message shows to see a more de-  
tailed oil level. (See Oil level j14 )  
–
Failure to do so risks causing damage to the  
engine.  
Park the vehicle at a safe location as soon as pos-  
sible and fill the engine with the recommended en-  
gine oil.  
switch or the  
–
Continued driving after maintenance due alert  
reaches 0 km (miles) may result in reduced  
engine performance. The engine malfunction  
indicator light (orange) will illuminate.  
For checking the engine oil level and adding oil, see  
“Engine oil” in the “8. Maintenance and  
do-it-yourself” section.  
NOTE  
The [Oil level OK] message indication is dis-  
played after the ignition switch has been turned  
to the ON position and other warnings have been  
shown.  
–
The DPF (where fitted) may also become satu-  
rated because regeneration is restricted once  
the distance equals 0 km (miles)  
j16 Engine oil sensor warning  
Please visit your local NISSAN dealer or qualified  
workshop if this warning appears.  
Always visit a NISSAN dealer or qualified work-  
shop to perform the maintenance and the reset.  
2-14 Instruments and controls  
Downloaded from manuals search engine  
However reset is possible (only after the oil was  
changed) using the [Service] menu item in the  
[Settings] menu. See “[Maintenance]” later in this  
section  
j23 Low temperature warning  
Stop/Start System (where fitted)  
If, during driving, the temperature falls below 4ºC  
this alert will appear to indicate low outside air tem-  
perature. You can switch the low temperature warn-  
ing [On] or [Off]. See “[Units]” later in this section  
For more information, see “Stop/Start System  
(where fitted)” in the “5. Starting and driving” sec-  
tion  
Have the vehicle inspected by a NISSAN dealer  
or qualified workshop if these conditions occur.  
j26 Engine stop:  
CAUTION  
If the engine stops when the Stop/Start System is  
activated, the message is shown.  
j20 Distance to maintenance alert  
(where fitted)  
Even if the alert is not on, there is no guarantee  
that the road is free of hazards caused by in-  
clement weather.  
j27 Auto start deactivation:  
This alert reminds when maintenance is due in the  
shown distance. The alert is shown for 10 seconds  
at ignition ON, when the distance to the next main-  
tenance interval is below 5000 km (3100 Miles).  
The message is shown until the steering wheel  
switch ji (where fitted) is pressed.  
If the engine stops when the Stop/Start System is  
activated, and will not start automatically, the mes-  
sage is shown.  
NOTE  
The outside air temperature sensor is located at  
the front of the vehicle. At low speeds the sensor  
can be affected by engine heat, heat reflected  
from the road surface and exhaust from other  
vehicles, these influences can cause the display  
to be inaccurate. To compensate, the outside air  
temperature display is designed to react slowly  
to increasing temperatures, but quickly to falling  
temperatures.  
j28 System fault:  
If the Stop/Start System is activated, but does not  
operate correctly, the message is shown. Visit a  
NISSAN dealer or qualified workshop.  
NOTE  
Visit a NISSAN dealer or qualified workshop  
•
before the maintenance due alert j19 reaches  
0 km (miles) to perform maintenance (oil  
change).  
Activating or deactivating using the Stop/Start  
System OFF switch:  
Using the Stop/Start System OFF switch activates  
or deactivates the Stop/Start System. This is shown  
in the vehicle information display:  
The maintenance interval will reduce faster  
with certain types of driving, especially at low  
speeds in urban conditions.  
•
j24 Low fuel warning  
This warning appears when the fuel level in the tank  
is getting low. Refuel as soon as it is convenient,  
preferably before the fuel gauge reaches the empty  
position. For more information, see “Fuel gauge”  
earlier in this section.  
j29 : The Stop/Start System OFF switch is  
pushed to the “ON” position.  
j21 Tyre change alert  
You can set a distance for changing tyres. See  
“[Maintenance]” later in this section  
j30 : The Stop/Start System OFF switch is pushed to  
the “OFF” position.  
j22 Maintenance alert  
j25 Driver alert  
You can set a distance for a non specific mainte-  
nance item. See “[Maintenance]” later in this sec-  
tion  
This warning appears when the previously set time  
for a break is reached. You can set the time for up  
to 6 hours in the setting menu. (See “Settings menu”  
later in this section.)  
Instruments and controls 2-15  
Downloaded from manuals search engine  
The trip computer is controlled using the  
or the steering wheel switch ji (where fitted).  
switch  
ODOMETER/TWIN TRIP ODOMETER  
BRIGHTNESS CONTROL  
Rotate the  
switch jC anticlockwise to brighten  
The trip computer contains the following items:  
or clockwise to dim the instrument lighting level.  
[Fuel Economy] → [Average speed] → [Driving dis-  
tance] → [Elapsed time] → [Range] (km or MILES)  
→ [Settings][→ CO2 Saved] (where fitted) → [Fuel  
Economy]  
NOTE  
Brightness cannot be set when the headlight  
switch is in the OFF position.  
TRIP COMPUTER  
Short press to change the information that is  
being displayed.  
•
NIC1542  
Push and hold (up until 3 seconds) resets the  
current item that is displayed (except [Settings]  
and [Range]).  
•
The odometer and twin trip odometer are displayed  
when the ignition switch is in the ON position.  
Push and hold over 3 seconds performs a global  
reset. This resets all functions of the display (ex-  
cept [Range] and Trip A).  
•
Odometer  
The odometer jA records the total distance the ve-  
hicle has been driven.  
j1 Fuel Economy (l (litre)/100 km or  
MPG)  
Twin trip odometer  
The [Fuel Economy] mode shows the current fuel  
consumption in a moving bar graph.  
The twin trip odometer jB records the distance of 2  
individual trips (Trip A and Trip B).  
The average fuel consumption mode displays the  
average fuel consumption since the last reset.  
Changing the display:  
Briefly press the  
play as follows.  
switch jC to change the dis-  
It is shown in 2 ways:  
The Ø symbol (average) with the value on the  
•
Trip A → Trip B→ Trip A  
top right of the bar.  
Resetting the trip odometer:  
By the position of the ♦ icon (diamond) inside  
the bar.  
•
Press and hold the  
switch for approximately 1  
second to reset the selected trip (Trip A or Trip B).  
NIC1650  
2-16 Instruments and controls  
Downloaded from manuals search engine  
For more information, see “Settings menu” later in  
this section.  
j2 Average speed  
The [Average speed] mode shows the average ve-  
hicle speed since the last reset.  
j7 CO2 saved (where fitted)  
Estimated quantity of CO2 exhaust emissions pre-  
vented by Stop/Start System shown every time the  
engine is automatically stopped.  
j3 Driving distance  
The [Driving distance] mode shows the distance  
driven since the last reset.  
For more information, see “Stop/Start System  
(where fitted)” in the “5. Starting and driving” sec-  
tion  
j4 Elapsed time  
The [Elapsed Time] mode shows the time since the  
last reset.  
j5 Range (km or MILES)  
The [Range] mode provides you with an estimation  
of the distance that can be driven before refuelling  
(distance to empty). The range is constantly being  
calculated, based on the amount of fuel in the fuel  
tank and the actual fuel consumption.  
When the fuel level gets close to empty, the range  
will change to “----”.  
If the amount of fuel added is small, the display  
just before the ignition switch is turned to the  
“OFF” position may continue to be displayed.  
•
When driving uphill or corners, the fuel in the  
tank shifts, this may momentarily change the dis-  
play.  
•
j6 Settings  
The [Settings] item is only displayed when using the  
switch to control the trip computer.  
Rotate the  
switch to enter the [Settings] menu  
Instruments and controls 2-17  
Downloaded from manuals search engine  
Petrol models  
Diesel models  
jA  
jB  
SETTINGS MENU  
Select the [Settings] menu in the trip computer then  
rotate the  
Use the  
switch to enter the Settings menu.  
switch to select and set the items.  
NOTE  
Settings cannot be changed while driving.  
NIC1708  
2-18 Instruments and controls  
Downloaded from manuals search engine  
To return to the previous screen of the setting mode,  
select [Back].  
[Units]  
The following items can be set to your preference.  
[Temperature]  
•
Select this submenu to choose from degrees  
Celsius (C) or Fahrenheit (F) on the display.  
[Dist./Fuеl]  
•
The fuel consumption units can be set too.  
Select this submenu to choose:  
–
–
–
distance in miles, fuel consumption in MPG  
distance in km, fuel consumption in km/l  
distance in km, fuel consumption in l/100km  
To return to the previous screen of the setting mode,  
select [Back].  
[Alarms]  
Alerts can be set to notify the following items.  
NIC1647  
[Driver Alert]  
•
Select this submenu to set the [Driver Alert] pe-  
riod.  
[On] or [Off]  
•
•
[Clock]  
Select this submenu to set the clock display On  
or Off.  
Clock adjustment can be set to:  
[Outside temp]  
•
[Set Clock]  
•
Select this submenu to set the low temperature  
alert [On] or [Off].  
[24/12 Нr]  
Adjust the time (hour and minute) of the clock on  
Select this submenu to set the 12h/24h time dis-  
play mode.  
the meter by rotating the  
switch.  
To return to the top page of the setting mode, select  
[Back].  
Push the switch to set the values  
Instruments and controls 2-19  
Downloaded from manuals search engine  
3) Select [Confirm] to confirm the reset of the  
distance driven information to zero.  
[Stop/Start] (where fitted)  
[Maintenance]  
The CO2 savings and the engine stop time using  
the Stop/Start System are kept in a submenu.  
The maintenance intervals of the following remind-  
ers can be set or reset:  
For Diesel models jB :  
1) Select [Service].  
[Trip Saving]  
[Service] for engine oil change service reminder  
•
•
2) Press the  
switch for more than 2 sec-  
View the estimated CO2 exhaust emissions pre-  
vented since last reset.  
Select this submenu to view, or reset the dis-  
tance driven information or to set an interval  
(petrol models).  
onds, then release.  
3) Select [Reset].  
It is possible to reset using the [Reset CO2]  
submenu then push the  
switch to set to zero.  
–
View the distance driven information:  
Select [Service].  
4) Select [Confirm] to confirm the reset proce-  
dure.  
NOTE  
Alternatively while the oil service message is  
displayed (where fitted):  
–
Set procedure (petrol models only jA ):  
The [Trip Saving] value is the same informa-  
tion that is displayed when the engine is auto-  
matically stopped by the Stop/Start System.  
1) Select [Service].  
After changing the engine oil: Turn the igni-  
tion switch to ON and, while the oil service  
message is displayed within 3 seconds, push  
2) Select the distance driven/interval informa-  
tion.  
[Total Saving]  
View:  
•
both the  
and  
switches at the same  
3) Turn the  
switch and set the interval (mile-  
time for more than 5 seconds.  
age) accordingly. For interval (mileage) de-  
tails, see the separately provided Warranty  
Information and Maintenance booklet.  
–
The estimated CO2 exhaust emissions pre-  
vented.  
The display goes blank for 1 second; the de-  
fault interval is then displayed; and finally the  
display returns to normal.  
–
The time that the engine has been stopped  
by the Stop/Start System.  
4) Short press the  
interval (mileage).  
switch to confirm the set  
[Tyre]  
•
•
NOTE  
–
Reset procedure after changing engine oil.  
Select this submenu to set or reset the distance  
for replacing tyres.  
The [Total Saving] values cannot be reset  
and show accumulated Stop/Start System  
information since the vehicle was built.  
CAUTION  
[Other]  
Do not perform the reset operation unless  
the engine oil has been changed.  
For more information, see “Stop/Start System  
(where fitted)” in the “5. Starting and driving” sec-  
tion.  
Select this submenu and set or reset the dis-  
tance for replacing or checking other items.  
For Petrol models jA :  
To return to the previous page of the setting mode,  
select [Back].  
1) Select [Service].  
2) Select [Reset].  
2-20 Instruments and controls  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals