2007-2012 Nissan X Trail SUV Instruments and controls -> Headlight and turn signal switch User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Headlight and turn signal switch for Your Nissan X Trail SUV Second Generation (2007-2012)

(95,1)
[ Edit: 2014/ 11/ 7 Model: T32-A ]
Turning the TSR system on and off
GUID-1E6BCBF6-FF04-4185-8DA1-454630A7E519
Turning the LDW system on or off is done using the
[Settings] menu in the vehicle information display. For
details, see “Vehicle information display” (P.2-20).
Perform the following steps to enable or disable the
TSR system:
1. In the [Settings] menu, select the [Driver Assis-
tance] key.
2. Touch [Traffic Sign] to turn the system ON/OFF.
System temporarily unavailable
GUID-BA4EC994-FA78-43F4-8A11-6FA33E2CC5A5
If the vehicle is parked in direct sunlight under high
temperature conditions (over approximately 408C
(1048F ) and then started, the TSR system may be
deactivated automatically. The [Not availab le high
cabin temperature] warning message will appear in
the vehicle information display.
Action to take:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
When the interior temperature is reduced, the TSR
system will resume operating automatically.
System Malfunction
GUID-CB9A153C-B940-4796-BEC6-E0CED93B2DA4
If the TSR system malfunctions it will be turned off
automatically and the system [Malfunction]/[System
error] warning message will appear in the vehicle
information display.
Action to take:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
If the TSR [Malfunc tion]/[System er ror] message
appears, pull off the road at a safe location and stop
the vehicle. Turn the engine off and restart the engine.
If the TSR [Malfunc tion]/[System er ror] message
continues to appear, have the system checked by a
NISSAN dealer.
Maintenance
GUID-4011F179-FBB0-4982-88ED-C90E38F62B76
The TSR uses the same multi-sensing front camera
unit that is used by the Lane Departure Warning
(LDW) system, located in front of the interior rearview
mirror. For maintenance of the camera, see “Multi-
sensing camera unit maintenance” (P.5-41).
T32A130827-AE66DA86-EADA-49AF-BE4F-98EA59F26D29
HEADLIGHT SWITCH
T32A130827-2D45301A-C88C-4C7B-B333-62ABD6D576C9
JVI0854X
Type A
JVI0859X
Type B
NISSAN recommends that you consult the local
regulations concerning the use of lights.
position
T32A130827-22A6378D-658B-4901-AA34-6B632DCB958D
The position turns on the front clearance, tail,
license plate and instrument panel lights.
Instruments and controls 2-39
HEADLIGHT AND TURN SIGNAL
SWITCH
Condition: 'Except for China'/
(96,1)
[ Edit: 2014/ 11/ 7 Model: T32-A ]
2-40 Instruments and controls
position
T32A130827-7DA4961D-ADB9-48C2-AF3E-CB8FF4FAA66E
The position turns on the headlights in addition to
the other lights.
AUTO position (if equipped)
T32A130827-42005CFF-F09D-4D2E-B51A-E A900BA8AB95
When the ignition switch is in the “ON” position and
the headlight switch is in the “AUTO” position, the
headlights, front clearance lights, instrument panel
lights, rear combination lights and other lights turn on
automatically depending on the brightness of the
surroundings.
The headlights will turn on automatically at twilight or in
rainy weather (when the windshield wiper is operated
continuously).
When the ignition switch is placed in the “LOCK” or
“OFF” position, the lights will turn off automatically.
JVI0510X
CAUTION:
Do not place any objects on top of the sensor
*
A
. The sensor senses the brightness level and
controls the autolight function. If the sensor is
covered, it r eacts as if it is dark, and the
headlights will illuminate.
Headlight beam
T32A130827-9CEFEA7E-F212-4D2D-A4BD-2DF2318D931E
JVI0856X
Type A
JVI0994X
Type B
To turn on the high beam, push the lever towards the
front position
*
1
.
To turn off the high beam, return the lever to the neutral
position
*
2
.
To flash the headlights, pull the lever towards the
rearmost position
*
3
. The headlights can be flashed
even when the headlights are not on.
If equipped, when the lever is pulled towards the
rearmost position
*
3
after the ignit i on switch is
placed in the “OFF” or “LOCK” position, the headlight
will turn on and stay on for 30 seconds. The lever can
be pulled 4 times for up to 2 minutes.
High beam assist (if equipped)
GUID-A9E44EB1-B8C0-468F-A5B4-1A9C35090997
The high beam assist system will operate when the
vehicle is driven at speeds of approximately 40 km/h
(25 MPH) and above. If an oncoming vehicle or leading
vehicle appears in front of your vehicle when the
headlight high beam is on, th e headlight will be
switched to the low beam automatically.
Precautions on high beam assist:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
WARNING:
. The high beam assist system is a conve-
nience but it is not a substitute for safe
driving operation. The driver should remain
alert at all times, ensure safe driving prac-
tices and switch the high beam and low
beam manually when necessary.
. The high beam or low beam may not switch
automatically under the following condi-
tions. Switch the high beam and low beam
manually.
— Durin g bad weather (rain, fog, sno w,
wind, etc.).
— When a light source similar to a head-
light or tail light is in the vicinity of the
vehicle.
— When the headlights of the oncoming
vehicle or the leading vehicle are turned
off, when the color of the light is
affected due to foreign materials on
the lights, or when the light beam is
out of position.
Condition: 'Except for China'/
(97,1)
[ Edit: 2014/ 11/ 7 Model: T32-A ]
— When there is a sudden, c ontinuous
change in brightness.
— When driving on a road that passes over
rolling hills, or a road that has level
differences.
— When driving on a road wit h many
curves.
— When a sign or mirror-like surface is
reflecting intense light towards the front
of the vehicle.
— When the container, etc. being towed by
a leading vehicle is reflecting intense
light.
— When a head l i g h t on your vehicle is
damaged or dirty.
— When the vehicle is leaning at an angle
due to a punctured tire, being towed,
etc.
. The timing of switching the low beam and
high beam may change under the following
situations.
— The brightness of the headlights of the
oncoming vehicle or leading vehicle.
— The m ovement and direction of the
oncoming vehicle and the leading vehi-
cle.
— When only one light on the oncoming
vehicle or the leading vehicle is illumi-
nated.
— When the oncoming vehicle or the lead-
ing vehicle is a two-wheeled vehicle.
— Road conditions (incline, curve, the road
surface, etc.).
— The number of passengers and the
amount of luggage.
High beam assist operations:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
JVI0974X
Type A
JVI0996X
Type B
To activate the high beam assist system, turn the
headlight switch to the “AUTO” position
*
1
and push
the lever forward
*
2
(high beam position). The high
beam assist indicator light in the meter will illuminate
while the headlights are turned on.
If the high beam assist indicator light does not
illuminate in the above condition, it may indicate that
the system is not functioning properly. Have the system
checked by a NISSAN dealer.
When the vehicle speed lowers to less than approxi-
mately 25 km/h (16 MPH), the headlight remains the
low beam.
To turn off the high beam assist system, turn the
headlight switch to the
position or select the low
beam position by placing the lever in the neutral
position.
Ambient image sensor maintenance:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
JVI0975X
The ambient image sensor
*
1
for the high beam
assist system is located in front of the inside rearview
mirror. To keep the proper operation of the high beam
assist system and prevent a system malfunction, be
sure to observe the following:
. Always keep the windshield clean.
. Do not attach a sticker (including transparent
material) or install an accessory near the ambient
image sensor.
. Do not strike or damage the areas around the
ambient image sensor. Do not touch the sensor
lens that is located on the ambient image sensor.
If the ambient image sensor is damaged due to an
Instruments and controls 2-41
Condition: 'Except for China'/
(98,1)
[ Edit: 2014/ 11/ 7 Model: T32-A ]
2-42 Instruments and controls
accident, contact a NISSAN dealer.
Daytime running light system
T32A130827-03F4324C-0702-4A59-BBC8-01F30381336D
Even if the headlight switch is * position, the daytime
running lights will come on after starting the engine.
When the light switch is turned to the
position, the
daytime running light will turn off.
HEADLIGHT AIMING CONTROL
T32A130827-A1D7D009-92AF-4459-81E1-BE4387A95870
JVI0477X
Manual type
T32A130827-76E07AD9-CA96-44FA-AB9E-4D2046E5D91B
The headlight aiming control operates when the
ignition switch is in the “ON” position and the headlight
is on to allow the headlight axis to be adjusted
according to the driving condition.
When driving with no heavy load/luggage or driving on
a flat road, select the normal position “0”.
If the number of occupants and load/luggage in the
vehicle changes, the headlight axis may become higher
than normal.
If the vehicle is traveling on a hilly road, the headlights
may directly shine on the rearview and outside mirrors
of a vehicle ahead or the windshield of an oncoming
vehicle, which may obscure other drivers’ vision.
To adjust to the proper aiming height, turn the switch
accordingly. The higher the number, designated on the
switch, the lower the headlight axis.
Select the switch position by referring to the following
samples.
Condition: 'Except for China'/
(99,1)
[ Edit: 2014/ 11/ 7 Model: T32-A ]
Two-row model
Switch posi-
tion
Number of
front seat
occupants
Number of
rear seat oc-
cupants
Weight of load in luggage compartment [APPROX. kg ( lb )]
2WD
4WD
MR20 QR25 R9M MR20 QR25
R9M
MT M-CVT CVT M-CVT CVT MT M-CVT M-CVT CVT M-CVT CVT
MT
0 1 or 2
No occu-
pants
No load
1 2
3
2 2 3
102 kg
(225 lb)
111 kg
(245 lb)
65 kg
(143 lb)
120 kg
(265 lb)
64 kg
(141 lb)
170 kg
(375 lb)
178 kg
(392 lb)
117 kg
(258 lb)
75 kg
(165 lb)
152 kg
(335 lb)
123 kg
(271 lb)
252 kg
(556 lb)
3 1
No occu-
pants
305 kg
(673 lb)
318 kg
(701 lb)
251 kg
(553 lb)
318 kg
(701 lb)
266 kg
(587 lb)
365 kg
(805 lb)
371 kg
(818 lb)
322 kg
(710 lb)
269 kg
(593 lb)
359 kg
(792 lb)
332 kg
(732 lb)
436 kg
(961 lb)
Three-row model
Switch posi-
tion
Number of
front seat
occupants
Number of
second row
seat occu-
pants
Number of
third row
seat occu-
pants
Weight of load in luggage compartment [APPROX. kg ( lb )]
2WD
4WD
MR20 QR25 R9M QR25
R9M
MT M-CVT CVT M-CVT CVT MT M-CVT M-CVT
MT
0 1 or 2
No occu-
pants
No occu-
pants
No load
1 2
No occu-
pants or 3
2
2 2 3 2
95 kg
(209 lb)
62 kg
(137 lb)
61 kg
(135 lb)
134 kg
(295 lb)
57 kg
(126 lb)
137 kg
(302 lb)
142 kg
(313 lb)
30 kg (66
lb)
141 kg
(311 lb)
3 1
No occu-
pants
No occu-
pants
472 kg
(1041 lb)
438 kg
(966 lb)
428 kg
(944 lb)
509 kg
(1122 lb)
420 kg
(926 lb)
524 kg
(1155 lb)
515 kg
(1136 lb)
474 kg
(1045 lb)
525 kg
(1158 lb)
Instruments and controls 2-43
Condition: 'Except for China'/
(100,1)
[ Edit: 2014/ 11/ 7 Model: T32-A ]
2-44 Instruments and controls
Automatic type
T32A130827-66387FF4-1CC3-4BDA-8563-27530E2881E3
The headlights are equipped with the automatic
leveling system. Headlight axis is controlled automati-
cally.
BATTERY SAVER SYSTEM
T32A130827-61CE9F9B-3E2D-4043-B79E-11558E12A2B4
The light reminder chime will sound if the headlight
switch is in either the
or position and when
the driver’s door is opened with the ignition switch in
the “OFF” or “LOCK” position.
Type A:
If the ignition switch is placed in “OFF” or “LOCK”
position while the headlight switch is in the
or
position, the battery saver function will turn off the
lights after a period of time to prevent the battery from
being discharged. The lights will turn on when the
doors are being opened.
Type B:
If the ignition switch is placed in “OFF” or “LOCK”
position while the headlight switch is in the
or
position, the battery saver function will turn off the
lights after opening the driver’s side door.
HEADLIGHT CLEANER (if equipped)
GUID-1CA84B69-AE3D-46F1-9857-AC539E6ACDC6
JVI1002X
Headlight cleaner switch (if equipped)
The headlight cleaner operates when the headlight is
on and the ignition switch is in the “ON” position.
To operate the headlight cleaner:
. Push the headlight cleaner switch (if equipped)
. Pull the windshield washer switch toward you.
— The headlight cleaner operates with the wind-
shield washer operation. This operation acti-
vates once each time either the ignition switch
or the headlight switch is turned off and on.
— After the first operation, the headlight cleaner
operates once at every fifth operation of the
windshield washer.
See “Wiper and washer switch” (P.2-47).
CAUTION:
. Do not operate the washer if the window
washer fluid reservoir is empty.
TURN SIGNAL SWITCH
T32A130827-37FAA258-280A-4947-AF44-BF748654C1C2
JVI0857X
Type A
JVI0995X
Type B
CAUTION:
The turn signal switch will not be cancelled
automatically if the steering wheel turning angle
does not exceed the preset amount. After the
turn or lane change, make sure that the turn
signal switch is returned to its original position.
Condition: 'Except for China'/

Related Topics

Instruments and controls
Cockpit Instrument panel Meters and gauges Compass (if equipped) Warning/indicator lights and audible reminders Vehicle information display Fog light switch Wiper and washer switch Defogger switch Horn Windows Sunroof (if equipped) Power outlets Ashtrays and cigarette lighter (if equipped) Storages Luggage compartment Coat hook Tonneau cover (if equipped) Roof rail (if equipped) Sun visors Interior lights HomeLink? Universal Transceiver (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot