Get Instruments and controls -> HomeLink? Universal Transceiver (if equipped) Guide for Nissan X Trail SUV Second Generation (2007-2012)

(119,1)

[ Edit: 2014/ 11/ 7 Model: T32-A ]

. The ignition switch is placed in the “ON” position.

When the switch is in the “OFF” position

, the room

light does not illuminate, regardless of any condition.

REAR PERSONAL LIGHTS (if equipped)

T32A130827-E33A0418-71E4-4783-8776-95BDD8E0633C

SIC3250

To turn the rear personal lights on, push the switch. To

turn them off, push the switch again.

VANITY MIRROR LIGHT

T32A130827-60D8B568-1434-44D8-97EC-1FD013843CF8

SIC3869

To access the vanity mirror, pull the sun visor down and

flip open the mirror cover.

The vanity mirror light illuminates when the vanity mirror

cover is opened. When the cover is closed, the light

will turn off.

LUGGAGE ROOM LIGHT

T32A130827-B967DCD8-A40C-4BBC-9740-0F3A54FAB83F

The luggage room light illuminates when the back door

is opened. When the back door is closed, the light will

turn off.

BATTERY SAVER SYSTEM

T32A130827-2EE0927A-B246-4DC2-A9F2-1E86EFF57FE0

When the interior light stays on, it will auto-

matically turn off after a period of time when the

ignition switch has been placed in the “OFF”

position. To turn on the light again, place the

ignition switch in the “ON” position.

The interior light will automatically turn off within a

period of time after the latest operation of the following

with the ignition switch in the “OFF” position:

. Opening or closing any door

. Locking or unlocking with a key, the power door

lock switch, or using the Intelligent Key system

. Pushing the ignition switch

The light will turn on again when any of the above

operations is performed after the light has turned off

automatically.

GUID-D1681C6A-CB33-46B3-BDB8-12E1079EFE21

The HomeLink

Universal Transceive r provides a

convenient way to consolidate the functions of up to

three individual hand-held transmitters into one built-in

device.

HomeLink

Universal Transceiver:

. Will operate most Radio Frequency (RF) devices

such as garage doors, gates, home and office

lighting, entry door locks and security systems.

. Is powered by your vehicle’s battery. No separate

batteries are required. If the vehicle’s battery is

discharged or is disconnected, HomeLink

will

retain all programming.

When the HomeLink

Universal Transceiver is

programmed, retain the original transmitter for

future programming procedures (Example: new

vehicle purchases). Upon sale of the vehicle, the

programmed HomeLink

Universal Transceiver

buttons should be erased for security purposes.

For additional information, refer to “Program-

ming HomeLink

” (P.2-64).

WARNING:

. During the programming procedure your

garage door or security gate will open and

close (if the transmitter is within range).

Make sure that people or objects are clear of

the garage door, gate, etc. that you are

programming.

. Your vehicle’s engine should be turned off

while programming the HomeLink

Univer-

sal Transceiver. Do not breathe exhaust

gases; they contain colorless and odorless

carbon monoxide. Carbon monoxide is dan-

gerous. It can cause unconsciousness or

death.

Instruments and controls 2-63

HomeLink

UNIVERSAL

TRANSCEIVER (if equipped)

Condition: 'Except for China'/

(120,1)

[ Edit: 2014/ 11/ 7 Model: T32-A ]

2-64 Instruments and controls

PROGRAMMING HomeLink

GUID-0B22A911-974D-4638-8D21-BC973EB880FA

If you have any questions or are having difficulty

programming your HomeLink

buttons, refer to the

HomeLink

web site at:

NOTE:

It is also recommended that a new battery be

placed in the hand-held transmitter of the device

being programmed to HomeLink

for quicker

programming and accurate transmission of the

radio-frequency.

1. Position the end of your hand-held transmitter 26 -

76 mm (1 - 3 in) away from the HomeLink

surface, keeping the HomeLink

indicator light

in view.

JVI0428X

2. Using both hands, simultaneously press and hold

the desir ed HomeLink

butt on and handheld

transmitter button. DO NOT release until the

HomeLink

indicator light

flashes slowly and

then rapidly. When the indicator light fla s he s

rapidly, both buttons may be released. (The rapid

flashing indicates successful programming.)

JVI0429X

3. Press and hold the programmed HomeLink

button and observe the indicator light.

If the indicator light

is solid/continuous,

programming i s complete and your device

should activate when the HomeLink

button

is pressed and released.

If the indicator light

blinks rapidly for two

seconds and then turns to a solid/continuous

light, continue with Steps 4-6 for a rolling code

device. A second person may mak e the

following steps easier. Use a ladder or other

device. Do not stand on your vehicle to perform

the next steps.

4. At the receiver located on the garage door opener

motor in the garage, locate the “learn” or “smart”

button (the name and color of the button may vary

by manufacturer but it is usually located near

where the hanging antenna wire is attached to the

unit). If there is difficulty locating the button,

reference the garage door opener’s manual.

5. Press and release the “learn” or “smart” button.

NOTE:

O nce the button is pressed, you have

approximate ly 30 seconds to initiate the

next step.

6. Return to the vehicle and firmly press and hold the

programmed HomeLink

button for two seconds

and release. R epeat the “press/hold/r elease”

sequence up to 3 times to complete the program-

ming process. HomeLink

should now activate

your rolling code equipped device.

7. If you have any questions or are having difficulty

programming your HomeLink

buttons, refer to the

HomeLink

web site at:

OPERATING THE HomeLink

UNIVERSAL

TRANSCEIVER

GUID-68441759-7704-47A0-BE37-19F4DFFABB83

The HomeLink

Universal Tr ansceiver, af ter it is

programmed, can be used to activate the programmed

device. To operate, simply press and release the

appropriate programmed HomeLink

Universal Trans-

ceiver button. The amber indicator light will illuminate

while the signal is being transmitted.

For convenience, the hand-held transmitter of the

device may also be used at any time.

PROGRAMMING TROUBLESHOOTING

GUID-A6AD2DFC-C4A4-4F60-AE87-75B4679FD409

If the HomeLink

does not quickly learn the hand-held

transmitter information:

. replace the hand-held transmitter batteries with

new batteries.

. position the hand-held transmitter with its battery

area facing away from the HomeLink

surface.

. press and hold both the HomeLink

and hand-

held transmitter buttons without interruption.

. position the hand-held transmitter 26 to 76 mm (1

to 3 in) away from the HomeLink

surface. Hold

Condition: 'Except for China'/

(121,1)

[ Edit: 2014/ 11/ 7 Model: T32-A ]

the transmitter in that positio n for up to 15

seconds. If HomeLink

is not programmed within

that time, try holding the transmitter in another

position - keeping the indicator light in view at all

times.

If you have any questions or are having difficulty

programming your HomeLink

buttons, refer to the

HomeLink

web site at:

CLEARING THE PROGRAMMED INFOR-

MATION

GUID-08D972A2-A208-4044-ACAD-8B01836AC192

Th e fol lowing proce dure clears the programmed

information from both buttons. Indiv idual but tons

cannot be cleared. However, individual buttons can

be reprogrammed, see “Reprogramming a single

HomeLink

button” (P.2-65).

To clear all programming

GUID-3AEA6B1C-6970-4F3D-9E19-D2B4279D6E00

1. Press and hold the two outer HomeLink

buttons

until the indicator light begins to flash in approxi-

mately 10 seconds. Do not hold for longer than 20

seconds.

2. Release both buttons.

HomeLink

is now in the programming mode and can

be programmed at any time beginning with “Program-

ming HomeLink

” - Step 1.

REPROGRAMMING A SINGLE HomeLink

BUTTON

GUID-F98BB3C6-C31D-4655-A19F-8D5E8137BA0B

To reprogram a HomeLink

Universal Transceiver

button, complete the following.

1. Press and hold the desired HomeLink

button. Do

not release the button.

2. The indicator light will begin to flash after 20

seconds. Without releasing the HomeLink

but-

ton, proceed with “Programming HomeLink

” -

Step 1.

For questions or comments, contact HomeLink

at:

The HomeLink

Universal Transceiver button has now

been reprogrammed. The new device can be activated

by pushing the HomeLin k

button that was just

programmed. This procedure will not affect any other

programmed HomeLink

buttons.

IF YOUR VEHICLE IS STOLEN

GUID-E0EEA60A-412E-4342-A1A7-F725E8A1D589

If your vehicle is stolen, you should change the codes

of any non-rolling code device that has been pro-

grammed into HomeLink

. Consult the Owner’s

Manual of each device or call the manufacturer or

dealer of those devices for additional information.

When your vehicle is recovered, you will need to

reprogram the HomeLink

Universal Transceiver

with your new transmitter information.

Instruments and controls 2-65

Condition: 'Except for China'/

Instruments and controls -> HomeLink? Universal Transceiver (if equipped) for Your Nissan X Trail SUV Second Generation (2007-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals