2022-2026 Nissan X Trail SUV Instruments and controls -> Headlight and turn signal switch User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Headlight and turn signal switch for Your Nissan X Trail SUV Fourth Generation (2022-2026)

HEADLIGHT AND TURN SIGNAL SWITCH  
Turning the TSR system on and off  
Maintenance  
HEADLIGHT SWITCH  
Turning the LDW system on or off is done using  
the "Settings" menu in the vehicle information  
display. For details, see “Vehicle information  
display” (P.2-21).  
The TSR uses the same multi-sensing front  
camera unit that is used by the Lane Departure  
Warning (LDW) system, located in front of the  
interior rearview mirror. For maintenance of the  
camera, see “System maintenance” (P.5-44).  
Perform the following steps to enable or  
disable the TSR system:  
1. In the "Settings" menu, select the "Driver  
Assistance" key.  
2. Touch "Traffic Sign" to turn the system ON/  
OFF.  
JVI0854X  
System temporarily unavailable  
Type A  
If the vehicle is parked in direct sunlight under  
high temperature conditions (over approxi-  
mately 40°C (104°F ) and then started, the TSR  
system may be deactivated automatically. The  
“Not available high cabin temperature” warning  
message will appear in the vehicle information  
display.  
Action to take:  
When the interior temperature is reduced, the  
TSR system will resume operating automati-  
cally.  
JVI0859X  
System Malfunction  
Type B  
NISSAN recommends that you consult the local  
regulations concerning the use of lights.  
If the TSR system malfunctions it will be turned  
off automatically and the system "Malfunc-  
tion"/"System error" warning message will  
appear in the vehicle information display.  
position  
The position turns on the front clearance,  
tail, license plate and instrument panel lights.  
Action to take:  
If the TSR "Malfunction"/"System error" mes-  
sage appears, pull off the road at  
a
safe  
location and stop the vehicle. Turn the engine  
off and restart the engine. If the TSR "Malfunc-  
tion"/"System error" message continues to  
appear, have the system checked by a NISSAN  
dealer.  
Instruments and controls 2-43  
Automatic headlights off delay (if equipped):  
position  
You can keep the headlights on for up to 180  
seconds after you place the ignition switch in  
the “OFF” position and open any door then  
close all the doors.  
The  
addition to the other lights.  
position turns on the headlights in  
AUTO position (if equipped)  
When the ignition switch is in the “ON” position  
and the headlight switch is in the “AUTO”  
position, the headlights, front clearance lights,  
instrument panel lights, rear combination lights  
and other lights turn on automatically depend-  
ing on the brightness of the surroundings.  
You can adjust the period of the automatic  
headlights off delay from 0 seconds (OFF) to  
180 seconds. The factory default setting is 45  
seconds.  
For automatic headlights off delay setting, see  
“Lighting” (P.2-25).  
JVI0994X  
The headlights will turn on automatically at  
twilight or in rainy weather (when the wind-  
shield wiper is operated continuously) (if  
equipped).  
Type B  
To turn on the high beam, push the lever  
towards the front position  
Headlight beam  
.
To turn off the high beam, return the lever to  
the neutral position  
When the ignition switch is placed in the “LOCK”  
or “OFF” position, the lights will turn off auto-  
matically.  
.
To flash the headlights, pull the lever towards  
the rearmost position . The headlights can be  
flashed even when the headlights are not on.  
If equipped, when the lever is pulled towards  
the rearmost position  
after the ignition  
switch is placed in the “OFF” or “LOCK” position,  
the headlight will turn on and stay on for 30  
seconds. The lever can be pulled 4 times for up  
to 2 minutes.  
JVI0856X  
Type A  
High beam assist (if equipped)  
The high beam assist system will operate when  
the vehicle is driven at speeds of approximately  
40 km/h (25 MPH) and above. If an oncoming  
vehicle or leading vehicle appears in front of  
your vehicle when the headlight high beam is  
on, the headlight will be switched to the low  
beam automatically.  
JVI0510X  
if equipped  
CAUTION:  
Do not place any objects on top of the sensor  
. The sensor senses the brightness level  
and controls the auto headlight/Intelligent  
Auto Headlight function. If the sensor is  
covered, it reacts as if it is dark, and the  
headlights will illuminate.  
2-44 Instruments and controls  
— When a headlight on your vehicle is  
damaged or dirty.  
Precautions on high beam assist:  
WARNING:  
High beam assist operations:  
— When the vehicle is leaning at an  
angle due to a punctured tire, being  
towed, etc.  
.
The high beam assist system is a con-  
venience but it is not a substitute for safe  
driving operation. The driver should re-  
main alert at all times, ensure safe driving  
practices and switch the high beam and  
low beam manually when necessary.  
.
The timing of switching the low beam  
and high beam may change under the  
following situations.  
— The brightness of the headlights of  
the oncoming vehicle or leading ve-  
hicle.  
.
The high beam or low beam may not  
switch automatically under the following  
conditions. Switch the high beam and low  
beam manually.  
— The movement and direction of the  
oncoming vehicle and the leading  
vehicle.  
JVI0974X  
Type A  
— During bad weather (rain, fog, snow,  
wind, etc.).  
— When only one light on the oncoming  
vehicle or the leading vehicle is illu-  
minated.  
— When a light source similar to a head-  
light or tail light is in the vicinity of  
the vehicle.  
— When the oncoming vehicle or the  
a
leading vehicle is  
vehicle.  
two-wheeled  
— When the headlights of the oncoming  
vehicle or the leading vehicle are  
turned off, when the color of the light  
is affected due to foreign materials  
on the lights, or when the light beam  
is out of position.  
— Road conditions (incline, curve, the  
road surface, etc.).  
— The number of passengers and the  
amount of luggage.  
JVI0996X  
— When there is a sudden, continuous  
change in brightness.  
Type B  
To activate the high beam assist system, turn  
the headlight switch to the “AUTO” position  
— When driving on a road that passes  
over rolling hills, or a road that has  
level differences.  
and push the lever forward  
(high beam  
position). The high beam assist indicator light  
in the meter will illuminate while the headlights  
are turned on.  
— When driving on a road with many  
curves.  
— When a sign or mirror-like surface is  
reflecting intense light towards the  
front of the vehicle.  
If the high beam assist indicator light does not  
illuminate in the above condition, it may  
indicate that the system is not functioning  
properly. Have the system checked by a NISSAN  
dealer.  
— When the container, etc. being towed  
by  
intense light.  
a
leading vehicle is reflecting  
When the vehicle speed lowers to less than  
Instruments and controls 2-45  

Related Topics

Instruments and controls
Cockpit Instrument panel Meters and gauges Warning lights, indicator lights and audible reminders Vehicle information display Intelligent Driver Alertness (if equipped) Battery saver system Adaptive Front lighting System (AFS) (if equipped) Headlight cleaner (if equipped) Turn signal switch Fog light switch Wiper and washer switch Defogger switch Horn Heated steering wheel (if equipped) Windows Sunroof (if equipped) Power outlets Ashtrays and cigarette lighter (if equipped) Storage Sun visors Interior lights HomeLink? Universal Transceiver (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot