Get Instruments and controls -> HomeLink? Universal Transceiver (if equipped) Guide for Nissan X Trail SUV Fourth Generation (2022-2026)

HomeLink® UNIVERSAL

TRANSCEIVER (if equipped)

The HomeLink® Universal Transceiver provides

a convenient way to consolidate the functions

of up to three individual hand-held transmitters

into one built-in device.

PROGRAMMING HomeLink®

If you have any questions or are having

difficulty programming your HomeLink® but-

tons, refer to the HomeLink® web site at: www.

homelink.com.

HomeLink® Universal Transceiver:

Will operate most Radio Frequency (RF)

devices such as garage doors, gates, home

and office lighting, entry door locks and

security systems.

NOTE:

It is also recommended that a new battery be

placed in the hand-held transmitter of the

device being programmed to HomeLink® for

quicker programming and accurate trans-

mission of the radio-frequency.

Is powered by your vehicle’s battery. No

separate batteries are required. If the

vehicle’s battery is discharged or is discon-

nected, HomeLink® will retain all program-

ming.

JVI0429X

1. Position the end of your hand-held trans-

mitter 26 - 76 mm (1 - 3 in) away from the

HomeLink® surface, keeping the HomeLink®

3. Press and hold the programmed

HomeLink® button and observe the indica-

When the HomeLink® Universal Transceiver is

programmed, retain the original transmitter

for future programming procedures (Exam-

ple: new vehicle purchases). Upon sale of the

vehicle, the programmed HomeLink® Univer-

sal Transceiver buttons should be erased for

security purposes. For additional informa-

tion, refer to “Programming HomeLink®” (P.2-

76).

tor light.

indicator light

in view.

If the indicator light

is solid/continu-

ous, programming is complete and your

device should activate when the

HomeLink® button is pressed and re-

leased.

If the indicator light

blinks rapidly for

two seconds and then turns to a solid/

continuous light, continue with Steps 4-6

for

rolling code device.

second

WARNING:

person may make the following steps

easier. Use a ladder or other device. Do

not stand on your vehicle to perform the

next steps.

During the programming procedure your

garage door or security gate will open

and close (if the transmitter is within

range). Make sure that people or objects

are clear of the garage door, gate, etc.

that you are programming.

JVI0428X

4. At the receiver located on the garage door

opener motor in the garage, locate the

“learn” or “smart” button (the name and

color of the button may vary by manufac-

turer but it is usually located near where

the hanging antenna wire is attached to

the unit). If there is difficulty locating the

button, reference the garage door opener’s

manual.

2. Using both hands, simultaneously press

and hold the desired HomeLink® button

and handheld transmitter button. DO NOT

release until the HomeLink® indicator light

flashes slowly and then rapidly. When the

indicator light flashes rapidly, both buttons

may be released. (The rapid flashing indi-

cates successful programming.)

Your vehicle’s engine should be turned

off while programming the HomeLink®

Universal Transceiver. Do not breathe

exhaust gases; they contain colorless

and odorless carbon monoxide. Carbon

monoxide is dangerous. It can cause

unconsciousness or death.

5. Press and release the “learn” or “smart”

button.

2-76 Instruments and controls

NOTE:

position the hand-held transmitter 26 to 76

mm (1 to 3 in) away from the HomeLink®

surface. Hold the transmitter in that posi-

tion for up to 15 seconds. If HomeLink® is

not programmed within that time, try

holding the transmitter in another position

- keeping the indicator light in view at all

times.

REPROGRAMMING A SINGLE HomeLink®

BUTTON

To reprogram a HomeLink® Universal Transcei-

ver button, complete the following.

Once the button is pressed, you have

approximately 30 seconds to initiate the

next step.

6. Return to the vehicle and firmly press and

hold the programmed HomeLink® button

for two seconds and release. Repeat the

1. Press and hold the desired HomeLink®

button. Do not release the button.

“press/hold/release” sequence up to

2. The indicator light will begin to flash after

20 seconds. Without releasing the

HomeLink® button, proceed with “Program-

ming HomeLink®” - Step 1.

If you have any questions or are having

difficulty programming your HomeLink® but-

tons, refer to the HomeLink® web site at: www.

homelink.com.

times to complete the programming pro-

cess. HomeLink® should now activate your

rolling code equipped device.

7. If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site

at: www.homelink.com.

For questions or comments, contact

HomeLink® at: www.homelink.com.

CLEARING THE PROGRAMMED INFOR-

MATION

The HomeLink® Universal Transceiver button

has now been reprogrammed. The new device

can be activated by pushing the HomeLink®

button that was just programmed. This proce-

dure will not affect any other programmed

HomeLink® buttons.

The following procedure clears the pro-

grammed information from both buttons. In-

dividual buttons cannot be cleared. However,

individual buttons can be reprogrammed, see

“Reprogramming a single HomeLink® button”

(P.2-77).

OPERATING THE HomeLink® UNIVERSAL

TRANSCEIVER

The HomeLink® Universal Transceiver, after it is

programmed, can be used to activate the

programmed device. To operate, simply press

and release the appropriate programmed

HomeLink® Universal Transceiver button. The

amber indicator light will illuminate while the

signal is being transmitted.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change the

codes of any non-rolling code device that has

been programmed into HomeLink®. Consult the

Owner’s Manual of each device or call the

manufacturer or dealer of those devices for

additional information.

To clear all programming

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to

flash in approximately 10 seconds. Do not

hold for longer than 20 seconds.

For convenience, the hand-held transmitter of

the device may also be used at any time.

2. Release both buttons.

When your vehicle is recovered, you will need

to reprogram the HomeLink® Universal

Transceiver with your new transmitter infor-

mation.

PROGRAMMING TROUBLESHOOTING

If the HomeLink® does not quickly learn the

hand-held transmitter information:

HomeLink® is now in the programming mode

and can be programmed at any time beginning

with “Programming HomeLink®” - Step 1.

replace the hand-held transmitter batteries

with new batteries.

position the hand-held transmitter with its

battery area facing away from the

HomeLink® surface.

press and hold both the HomeLink® and

hand-held transmitter buttons without in-

terruption.

Instruments and controls 2-77

Instruments and controls -> HomeLink? Universal Transceiver (if equipped) for Your Nissan X Trail SUV Fourth Generation (2022-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals