Get Instruments and controls -> Vehicle information display Guide for Nissan X Trail SUV Fourth Generation (2022-2026)

VEHICLE INFORMATION DISPLAY

ignition switch.

HOW TO USE THE VEHICLE INFORMA-

TION DISPLAY

For more information, see “Stop/Start System

or Idling Stop System” (P.5-24).

JVI0641X

The vehicle information display

is located

between the tachometer and the speed-

ometer. It displays following items if the vehicle

is equipped with them:

JVI1566X

The vehicle information display can be chan-

ged using the buttons OK

,

located on the left side of the

,

.

Vehicle settings

and

steering wheel.

Trip computer information

Driver Assistance

OK - change or select an item in the

vehicle information display

Speed limiter information

Cruise control system information

- navigate through the items in vehi-

cle information display

Intelligent Cruise Control (ICC) system in-

formation

- go back to the previous menu

.

Intelligent Key operation information

Audio information

- change from one display screen

to the next (i.e. trip, Fuel economy)

Navigation - turn by turn

Indicators and warnings

Tyre pressure information

Chassis Control

The buttons on the steering wheel mounted

controls are also used to control audio func-

tions. For additional information, see “Steering

wheel mounted controls for audio” (P.4-72) or

the separate NissanConnect Owner’s Manual (if

equipped).

AdBlue® Selective Catalytic Reduction (SCR)

system information

.

Other information

Please note that the information used in this

manual is written in UK English. There are a few

differences in the information for the UK and

U.S. English versions of the system.

For language settings, see “Language” (P.2-29).

Instruments and controls 2-21

.

Driving Aids (if equipped)

Driver Attention (if equipped)

Traffic Sign (if equipped)

Parking Aids (if equipped)

Chassis Control

Driver Attention (if equipped) :

STARTUP DISPLAY

Intelligent Driver Alertness ON/OFF

When the ignition switch is placed in the “ON”

position, the screens that display in the vehicle

information display include:

Traffic Sign (if equipped) :

Traffic Sign ON/OFF

.

Trip computer

Fuel economy

Warnings

Parking Aids (if equipped) :

Driving Aids (if equipped) :

To change the status or turn on or off any of

the systems displayed in the “Parking Aids”

To change the status, warnings or turn on or

off any of the systems/warnings displayed in

the “Driving Aids” menu, use the

to select and the OK button

menu item:

Warnings will only display if there are any

present, for more information on warnings

and indicators, see “Vehicle information display

warnings and indicators” (P.2-30).

menu, use the button to select and the

OK button to change a menu item:

button

to change a

.

Moving Object (if equipped)

Press the OK button to turn the Moving

Object Detection (MOD) (if equipped) ON/

OFF.

To control what items display in the vehicle

information display, see “Settings” (P.2-22).

.

Emergency Brake (if equipped)

Press the OK button to turn the Intelli-

gent Emergency Braking system ON/OFF.

SETTINGS

Cross Traffic (if equipped)

.

Lane (if equipped)

The setting mode allows you to change the

information displayed in the vehicle informa-

tion display:

Press the OK button

to turn the Rear

— Warning

Cross Traffic Alert (RCTA) (if equipped) ON/

OFF.

Press the OK button

to turn the Lane

Departure Warning (LDW) system ON/

OFF.

.

Front Sensor (if equipped)

.

Driver Assistance

Clock

Press the OK button to turn ON/OFF.

Rear Sensor (if equipped)

— Assist (if equipped)

Press the OK button

Display Settings

Vehicle Settings

Maintenance

to turn the

Intelligent Lane Intervention system

ON/OFF.

Press the OK button

Display (if equipped)

Press the OK button

Volume (if equipped)

— High/Med./Low

Range (if equipped)

— Far/Mid./Near

to turn ON/OFF.

.

Blind Spot (if equipped)

Alert

Press the OK button to turn the Blind

Spot Warning (BSW) system ON/OFF.

Tyre Pressures (if equipped)

Units (if equipped)

Language (if equipped)

Factory Reset

— Warning (if equipped)

Press the OK button

to turn the Blind

Spot Warning (BSW) system ON/OFF.

For additional information, see “Rear Cross

Traffic Alert (RCTA)” (P.5-55), “Parking sensor

(sonar) system” (P.5-95) and “Intelligent Around

View Monitor/Around View Monitor” (P.4-11).

Driver Assistance

For additional information, see “Intelligent

Emergency Braking” (P.5-78), “Intelligent Emer-

gency Braking with pedestrian detection sys-

tem” (P.5-83), “Lane Departure Warning (LDW)”

(P.5-40) and “Blind Spot Warning (BSW)” (P.5-49).

To change the status, warnings or turn on or

off any of the systems/warnings displayed in

the “Driver Assistance” menu, use the

button to select and the OK button

change a menu item:

to

2-22 Instruments and controls

Chassis Control:

Automatic Time:

Display Settings

The display settings allows the customer to

choose from the various meter selections.

To change the status, warnings or turn on or

off any of the systems/warnings displayed in

the “Chassis Control” menu.

The adjustment settings can be selected from

“Auto”, “Manual” and “Time Zone”.

.

Auto

The display settings can be changed using the

and the OK

Use the

button

to change a menu item:

to select and the OK

buttons.

Manual

Time Zone

Contents Selection:

.

Trace Control

12H/24H:

The items that display when the ignition switch

is placed in the “ON” position can be enabled/

disabled. To change the items that are dis-

— See “Intelligent Trace Control” (P.5-36) for

more information.

The time setting can be selected from 12 hour

and 24 hour formats.

Press the OK button

to turn ON/OFF.

played, use the

OK button

button

to select a menu item.

to scroll and the

D.S.T:

.

Engine Brake (if equipped)

— See “Intelligent Engine Brake (Continu-

ously Variable Transmission (CVT)/Dual

Clutch Transmission (DCT) models)” (P.5-

37) for more information.

Turns the Daylight Savings Time on or off.

Body Colour:

Time Zone:

The color of the vehicle that displays in the

vehicle information display when the ignition

switch is placed in the “ON” position can be

changed.

Select the applicable time zone from the list.

Press the OK button

to turn ON/OFF.

Set Clock Manually:

The clock can be adjusted manually using the

and the OK

Clock

For models without navigation or audio

system:

1. Use the

button until “Body Colour” is

.

buttons.

selected, and press OK button

NOTE:

2. Select the body color using the

and press OK button

button

.

The clock is synchronized with the clock on

the center display. To set the clock on center

display, see the separate NissanConnect

Owner’s Manual.

Set Clock:

ECO Mode Settings (if equipped):

The clock setting can be changed using the

and the OK

buttons.

This setting allows the customer to change the

ECO mode system settings.

12H/24H:

For models with navigation or audio system

(except for NissanConnect):

Use the

Settings” is selected, and press OK button

button

until “ECO Mode

.

The time setting can be selected from 12 hour

and 24 hour formats.

To set the clock, see “Clock” (P.4-7), “Audio main

operation” (P.4-47), “Audio main operation” (P.4-

55) or “Audio main operation” (P.4-61) or the

separate Navigation System Owner’s Manual (if

equipped).

- ECO Glow

D.S.T (if equipped):

This setting allows the customer to enable/

disable the ambient ECO indicator in the

vehicle information display.

Turns the Daylight Savings Time on or off.

Time Zone (if equipped):

1. Use the

button

to select “ECO Glow”.

Select the applicable time zone from the list.

2. Press the OK button

to turn ON/OFF the

For models with NissanConnect navigation or

audio system:

ambient ECO in the vehicle information

display.

Instruments and controls 2-23

- Display

2. Press the OK button

to turn ON/OFF the

Stop/Start (if equipped):

ECO management display in the vehicle

information display.

To change the status, warnings or turn on or

off any of the systems/warnings displayed in

- View History

the “Stop/Start” menu, use the

select and the OK button

item:

button to

to change a menu

This setting allows the customer to reset the

past history of the fuel economy and the best

fuel economy.

.

Display

— Stop/Start display ON/OFF

Trip CO2 Saving

Welcome Effect:

.

You can choose whether or not to display the

welcome screen when the ignition switch is

placed in the “ACC” or “ON” position. You can

also choose the following items to define how

the welcome screen looks:

The “Trip CO2 Saving” and engine stop time

mode shows the CO2 saving and engine

stop time since the last reset. The CO2

saving and engine stop time can be reset

WAC0086X

Type A

by pushing the OK button

.

Dial and Pointer

Display Effect

.

Total CO2 saving

The “Total CO2 Saving” and engine stop

time mode shows:

Select “Welcome Effects” using the

and press the OK button

menu. Use the button

between the menu options and press the OK

button to turn each function ON/OFF.

button

to select this

to navigate

— The estimated CO2 exhaust emissions

prevented.

— The engine stop time that the engine

has been stopped by the “Stop/Start or

Idling Stop” System.

Vehicle Settings

The vehicle settings allows the customer to

change settings for the following settings.

NOTE:

The “Total CO2 saving” and engine stop

time values cannot be reset and show

accumulated “Stop/Start or Idling Stop”

System information since the vehicle was

built.

JVI0665X

.

Lighting

Type B

This setting allows the customer to enable/

disable the ECO pedal guide function.

Turn Indicator

Unlocking

Wipers

1. Use the

button

to select “Display”.

to select “Pedal

Mirrors

ECO Drive Report (if equipped):

- Display

2. Press the OK button

Guide” or “Fuel econ.”.

Remote Start (if equipped)

Driving Position (if equipped)

This setting allows the customer to enable/

disable the ECO Drive Report in the vehicle

information display.

For detailed information, see “ECO mode sys-

tem” (P.5-91).

The vehicle settings can be changed using the

, and the OK buttons.

1. Use the

Report”.

button

to select “ECO Drive

2-24 Instruments and controls

Lighting:

Unlocking (if equipped):

Wipers:

Speed Dependent (if equipped)

The “Lighting” menu has the following options:

There are the following options in the “Unlock-

ing” menu:

.

The “Speed Dependent” feature can be

activated or deactivated. From the “Wipers”

menu, select “Speed Dependent”. Use the

OK button to turn this feature ON or OFF.

.

Welcome Light

.

I–Key Door Lock (if equipped)

The welcome lighting can be set to be ON

or OFF. From the “Lighting” menu, select

“Welcome Light”. Use the OK button

turn this feature ON or OFF.

When this item is turned on, the request

switch on the door is activated. From the

“Unlocking” menu, select “I-Key Door Lock”.

Use the OK button to activate or

deactivate this function.

to

Auto Wipe (if equipped)

The “Auto Wipe” feature can be activated or

deactivated. From the “Wipers” menu, select

“Auto Wipe”. Use the OK button

this feature ON or OFF.

Int. Lamp Timer

The internal light timer can be set to be ON

or OFF. From the “Lighting” menu, select

“Int. Lamp Timer”. Use the OK button

turn this feature ON or OFF.

to turn

.

Selective Unlock (if equipped)

to

When this item is turned on, and the door

handle request switch on the driver’s or

front passenger’s side door is pushed, only

the corresponding door is unlocked. All the

doors can be unlocked if the door handle

request switch is pushed again within 1

minute. When this item is turned to off, all

the doors will be unlocked when the door

handle request switch is pushed once.

From the “Unlocking” menu, select “Selec-

Rain Sensor (if equipped)

The “Rain sensor” feature can be activated

or deactivated. From the “Wipers” menu,

select “Rain Sensor”. Use the OK button

to turn this feature ON or OFF.

Auto Lights (if equipped)

The sensitivity of the Auto Light or the

Intelligent Auto Headlight can be adjusted.

From the “Lighting” menu, select “Auto

Lights”. Use the button

button to select the required sensitivity.

The following options are available:

— On Earliest

Reverse Link

and the OK

The “Reverse Link” wiper feature can be set

to be ON or OFF. From the “Wipers” menu,

select “Reverse Link”. Use the OK button

to turn this feature ON or OFF.

tive Unlock”. Use the OK button

activate or deactivate this function.

to

— On Earlier

Drip Wipe

— Standard

.

Auto Door Unlock (if equipped)

The “Drip Wipe” feature can be set to be ON

or OFF. From the “Wipers” menu, select “Drip

— On Later

This menu allows the user to customize the

auto door unlock options. The following

options are available:

.

Headlight Off Delay (if equipped)

Wipe”. Use the OK button

feature ON or OFF.

to turn this

The duration of the automatic headlights

can be changed from 0 to 180 seconds.

From the “Lighting” menu, select “Headlight

Off delay”. Use the OK button

the duration.

— Ignition OFF

Mirrors (if equipped):

— Shift to Park

— Off

to change

.

Auto Fold Off

When this item is turned on, the auto fold

feature for the outside rearview mirrors is

Answer Bk. Horn (if equipped)

Turn Indicator:

When the answer back horn is on the horn

will chirp and the hazard indicators will

flash once when locking the vehicle with

the Intelligent Key or remote keyless entry

function.

disabled. Use OK button

function.

to select this

The “3 Flash On” overtaking feature can be set

to be ON or OFF. From the “Turn Indicator”

menu, select “3 Flash On”. Use the OK button

to turn this feature ON or OFF.

.

Unfold at Ignition

When this item is turned on, the outside

rearview mirrors automatically fold when

the ignition switch is placed in the “OFF”

position, and unfold when the ignition

switch is placed in the “ON” position. Use

Instruments and controls 2-25

the OK button

to select this function.

maintenance booklet.

Maintenance

.

Unfold at Unlock

Tyre:

When this item is turned on, the outside

rearview mirrors automatically fold when

the vehicle doors are locked, and unfold

when the vehicles doors are unlocked. Use

This indicator appears when the customer set

distance comes for replacing tires. You can set

or reset the distance for replacing tires.

the OK button

to select this function.

WARNING:

Remote Start (if equipped):

The tire replacement indicator is not a sub-

stitute for regular tire checks, including tire

pressure checks. See “Changing tires and

wheels” (P.8-43). Many factors including tire

inflation, alignment, driving habits and road

conditions affect tire wear and when tires

should be replaced. Setting the tire replace-

ment indicator for a certain driving distance

does not mean your tires will last that long.

Use the tire replacement indicator as a guide

only and always perform regular tire checks.

Failure to perform regular tire checks, includ-

ing tire pressure checks could result in tire

failure. Serious vehicle damage could occur

The “Remote Start” feature allows user to turn

the remote engine start on or off. When turned

on, the engine can be started remotely. See

“Remote engine start” (P.3-20) for more infor-

mation.

WAC0092X

1. Service

Driving Position (if equipped):

Displays the available driving position options.

2. Filter (if equipped)

3. Tyre

.

Exit Seat Slide

When this item is turned on, this feature will

move the driver’s seat backward for an

easy exit when the ignition is turned off and

the driver’s door is opened. After getting

into the vehicle and placing the ignition

switch in the ON position, the driver’s seat

will move to the previous set position. See

“Automatic drive positioner” (P.3-44) for

more information.

4. Other

5. AdBlue Status (if equipped)

The maintenance mode allows you to set alerts

for the reminding of maintenance intervals. To

change an item:

and may lead to

result in serious personal injury or death.

a

collision, which could

Select “Maintenance” using the

.

button

Other:

and press OK button

This indicator appears when the customer set

distance comes for checking or replacing

maintenance items other than the engine oil,

oil filter and tires. Other maintenance items can

include such things as air filter or tire rotation.

You can set or reset the distance for checking

or replacing the items.

Service:

This indicator appears when the customer set

distance comes for changing the engine oil and

filter. You can set or reset the distance for

checking or replacing these items. For sched-

uled maintenance items and intervals, see a

separate maintenance booklet.

AdBlue Status (if equipped):

Filter (if equipped):

You can use this option to check the level of

fluid in the AdBlue® tank. For more details, see

“AdBlue® Selective Catalytic Reduction (SCR)

system (if equipped for diesel engine model)”

(P.5-5).

This indicator appears when the customer set

distance comes for changing the oil filter. You

can set or reset the distance for checking or

replacing these items. For scheduled mainte-

nance items and intervals, see

a

separate

2-26 Instruments and controls

Phone (if equipped):

Target Rear:

Alert

This setting allows the customer to set alarms.

This setting allows the customer to enable/

disable the alert for an incoming call in the

vehicle information display.

The “Target Rear” tire pressure is the pressure

specified for the rear tires on the tire placard.

(See “Tire Pressure Monitoring System (TPMS)”

(P.5-9) and “Tire placard” (P.9-13).)

Select “Alert” using the

OK button

button and press

.

1. Use the

button

to select “Phone”.

Outside Temp. (if equipped):

Use the

button

and the OK button

to

2. Press the OK button

alert.

to turn ON/OFF the

This setting allows the customer to enable/

disable the alert for outside temperature in the

vehicle information display.

select and change the value for the “Target

Rear”/“Target rear” tire pressure.

Mail (if equipped):

This setting allows the customer to enable/

disable the alert for a mail receiving in the

vehicle information display.

1. Use the

Temp.”.

button

to select “Outside

2. Press the OK button

alert.

to turn ON/OFF the

1. Use the

button

to select “Mail”.

2. Press the OK button

alert.

to turn ON/OFF the

Timer:

This setting allows the customer to set an alert

to notify the driver that the set time has been

reached.

Tyre Pressures (if equipped)

The settings in the “Tyre pressures” menu are

all related to the Tire Pressure Monitoring

System (TPMS). (See “Tire Pressure Monitoring

System (TPMS)” (P.6-2), “Tire Pressure Monitor-

ing System (TPMS)” (P.5-9) and “Tire Pressure

Monitoring System (TPMS)” (P.8-42).)

1. Use the

button

to select “Timer”.

.

2. Press the OK button

3. To change the timer amount, use the

button and the OK button to save the

selected time amount.

.

Target Front

Target Rear

Tyre Pressure Unit

Calibrate

Navigation (if equipped):

This setting allows the customer to enable/

disable the alert for navigation in the vehicle

information display.

Target Front:

1. Use the

tion”.

button

to select “Naviga-

The “Target Front” tire pressure is the pressure

specified for the front tires on the tire placard.

(See “Tire Pressure Monitoring System (TPMS)”

(P.5-9) and “Tire placard” (P.9-13).)

2. Press the OK button

alert.

to turn ON/OFF the

Use the

button

and the OK button

to

select and change the value for the “Target

Front”/“Target front” tire pressure.

Instruments and controls 2-27

Tyre Pressure Unit:

The unit for tire pressure that displays in the

vehicle information display can be changed to:

.

kPa

bar

psi

Kgf/cm2

Use the

select and change the unit.

button

and the OK button

to

If necessary, refer to the following table to

convert between units.

JVI0938X

Units (if equipped)

The units that are shown in the vehicle

information display can be changed:

Calibrate:

The tire pressure is affected by the tempera-

ture of the tire; the tire temperature increases

when the car is driven. To be able to accurately

monitor the tire air leakage and to prevent false

TPMS warnings due to changes in temperature,

the TPMS system uses temperature sensors in

the tires to perform temperature compensa-

tion calculations.

.

Distance/Fuel

Tyre pressures (if equipped)

Temperature

Use the

button , and the OK button

to

select and change the units of the vehicle

information display.

On rare occasions it may be necessary to

recalibrate the TPMS system reference tem-

perature. This operation should only be per-

formed when the actual tire pressure has been

adjusted, while the current ambient tempera-

ture is significantly different to the current

calibration temperature. (See “Tire Pressure

Monitoring System (TPMS)” (P.5-9).)

Distance/Fuel:

The unit for the mileage that displays in the

vehicle information display can be changed to:

.

km, l/100km

km, km/l

miles, MPG (if equipped)

Use the

button

select and change the unit.

and the OK button

to

Use the

button , and the OK button

to

start or cancel the calibration process. While

the calibration process is active, the message:

“Resetting tyre pressure system” will be dis-

played.

Tyre pressures (if equipped):

See “Tyre Pressure Unit” (P.2-28).

2-28 Instruments and controls

Temperature:

The temperature that displays in the vehicle

information display can be changed from:

.

°C (Celsius)

°F (Fahrenheit)

Use the

button

to toggle choices.

Language (if equipped)

The language of the vehicle information display

can be changed.

Use the

button , and the OK button

to

select and change the language of the vehicle

information display. The language of the center

display/navigation can be changed indepen-

dently of the vehicle information display. For

models with Navigation System, see “Vehicle

information and settings (for type D audio)”

(P.4-5) or the NissanConnect Owner’s Manual.

For models without Navigation System, see

“Audio system” (P.4-39) or the NissanConnect

Owner’s Manual.

Factory Reset

The settings in the vehicle information display

can be reset back to the factory default. To

reset the vehicle information display:

1. Select “Factory Reset” using the

and press the OK button

button

.

2. Select “YES” to return all settings back to

default by pressing the OK button

.

Instruments and controls 2-29

VEHICLE INFORMATION DISPLAY WARNINGS AND INDICATORS

WAC0079X

2-30 Instruments and controls

1. Engine start operation indicator (for

Continuously Variable Transmission (CVT)/

Dual Clutch Transmission (DCT) models)

5. Shift to Park warning (Continuously

Variable Transmission (CVT)/Dual

Clutch Transmission (DCT) models)

This indicator appears when the shift lever is in

the “P” (Park) position.

This warning appears when the ignition switch

is pushed to stop the engine with the shift lever

in any position except the “P” (Park) position.

This indicator means that the engine will start

by pushing the ignition switch with the brake

pedal depressed. You can start the engine

directly in any position of the ignition switch.

If this warning appears, move the shift lever to

the “P” (Park) position or place the ignition

switch in the “ON” position.

An inside warning chime will also sound. (See

“Intelligent Key system” (P.3-11).)

2. Engine start operation indicator (for

Manual Transmission (MT) models)

6. Key battery low warning (if equipped)

This indicator appears when the Intelligent Key

battery is running out of power.

This indicator means that the engine will start

by pushing the ignition switch with the clutch

pedal depressed. You can start the engine

directly in any position of the ignition switch.

If this indicator appears, replace the battery

with a new one. See “Intelligent Key battery”

(P.8-28).

You can also start the engine by pushing the

ignition switch with the brake pedal depressed

when the shift lever is in the “N” (Neutral)

position.

7. Engine start operation for Intelligent

Key system indicator (if equipped)

This indicator appears when the Intelligent Key

battery is running out of power and when the

Intelligent Key system and vehicle are not

communicating normally.

3. Steering lock release malfunction

indicator (if equipped)

This indicator appears when the steering lock

cannot be released.

If this indicator appears, push or turn the

ignition switch while lightly turning the steering

wheel right and left.

If this indicator appears, touch the ignition

switch with the Intelligent Key while depressing

the brake pedal. (See “Intelligent Key battery

discharge” (P.5-16).)

See “Steering lock” (P.5-15).

8. Key ID incorrect warning (if equipped)

4. No Key detected warning (if equipped)

This warning appears when the ignition switch

is placed from the “LOCK” position and the

Intelligent Key cannot be recognized by the

system. You cannot start the engine with an

unregistered key. Use the registered Intelligent

Key.

This warning appears when the door is closed

with the Intelligent Key left outside the vehicle

and the ignition switch in the “ON” position.

Make sure that the Intelligent Key is inside the

vehicle.

WAC0546X

See “Intelligent Key system” (P.3-11) for more

details.

See “Intelligent Key system” (P.3-11).

Instruments and controls 2-31

sure Monitoring System (TPMS)” (P.5-9) and

“Tire Pressure Monitoring System (TPMS)” (P.8-

42).)

9. Release parking brake warning

13. Key System Fault warning (if equipped)

This warning appears when the vehicle speed

is above 7 km/h (4 MPH) (models not equipped

with electronic parking brake) or 4 km/h (2

MPH) (models equipped with electronic parking

brake) and the parking brake is applied. Stop

the vehicle and release the parking brake.

This warning appears if there is a malfunction

in the Intelligent Key system.

If this warning appears while the engine is

stopped, the engine cannot be started. If this

warning appears while the engine is running,

the vehicle can be driven. However, contact a

NISSAN dealer for repair as soon as possible.

17. Low oil pressure Stop vehicle warn-

ing (if equipped)

This warning appears if low engine oil pressure

is detected. If the warning appears during

normal driving, pull off the road in a safe area,

stop the engine immediately and call a NISSAN

dealer.

10. Low fuel level warning

This warning appears when the fuel level in the

fuel tank is getting low. Refuel as soon as it is

convenient, preferably before the fuel gauge

reaches 0 (Empty). There will be a small reserve

of fuel in the tank when the fuel gauge needle

reaches 0 (Empty).

14. Loose Fuel Cap warning (if equipped)

This warning appears when the fuel-filler cap is

not tightened correctly after the vehicle has

been refueled. (See “Fuel-filler cap” (P.3-32).)

The low oil pressure warning is not designed to

indicate a low oil level. Use the dipstick to check

the oil level. (See “Engine oil” (P.8-13).)

15. Low tyre pressure warning (if equipped)

CAUTION:

This warning (“Low tyre pressure” and a vehicle

icon - if equipped) appears when the low tire

pressure warning light in the meter illuminates

and low tire pressure is detected. The warning

appears each time the ignition switch is placed

in the “ON” position as long as the low tire

pressure warning light remains illuminated. If

this warning appears, stop the vehicle and

adjust the pressure to the recommended COLD

tire pressure shown on the tire placard. (See

“Low tire pressure warning light” (P.2-14), “Tire

Pressure Monitoring System (TPMS)” (P.6-2),

“Tire Pressure Monitoring System (TPMS)” (P.5-

9) and “Tire Pressure Monitoring System

(TPMS)” (P.8-42).)

11. Door/back door open warning

Running the engine with the engine oil

pressure warning displayed could cause

serious damage to the engine.

This warning appears if any of the doors and/

or the back door are open or not closed

securely. The vehicle icon indicates which door

or the back door is open on the display.

18. Oil Level Low indicator (if equipped)

12. Second row seat belt warning (if equipped)

If the low level indicator is displayed, the engine

oil level is low. If the low level reminder is

displayed, check the level using the engine oil

dipstick. (See “Engine oil” (P.8-13).)

This second row seat belt warning appears

after the ignition switch is placed in the “ON”

position. If any of the second row seat passen-

ger seat belts is not fastened, a chime will

sound and the seat icon illuminates in red to

show which seat belt is not fastened. The seat

icon illuminates in red until the corresponding

second row seat passenger’s seat belt is

fastened. The warning will automatically turn

off after approximately 35 seconds.

CAUTION:

The oil level should be checked regularly

using the engine oil dipstick. Operating with

an insufficient amount of oil can damage the

engine and such damage is not covered by

the warranty.

16. Tyre pressure system fault warning

(if equipped)

For precautions on seat belt usage, see “Seat

belts” (P.1-10).

This warning illuminates when there is

a

malfunction in the Tire Pressure Monitoring

System (TPMS).

If this warning comes on, have the system

checked by

a

NISSAN dealer. See “Low tire

pressure warning light” (P.2-14), “Tire Pressure

Monitoring System (TPMS)” (P.6-2), “Tire Pres-

2-32 Instruments and controls

19. Oil level sensor warning (if equipped)

26. Battery Voltage Low Charge Battery warning

32. Press brake pedal warning (for elec-

tronic parking brake equipped models)

If the oil sensor warning is displayed, the engine

oil level sensor may be malfunctioning. Contact

a NISSAN dealer immediately. For more details,

see “Oil control system” (P.2-36).

This warning appears when the battery voltage

is low and the battery needs to be charged.

This indicator appears in the following situa-

tions:

27. Shipping Mode On Push Storage Fuse warning

.

The driver tries to release the electronic

parking brake manually without depressing

the brake pedal.

This warning may appear if the extended

storage fuse switch is not pushed in (switched

on). When this warning appears, push in (switch

on) the extended storage fuse switch to turn

off the warning. For more information, see

“Extended storage fuse switch” (P.8-33).

20–21. 4WD system fault/AWD Error

warning (if equipped)

.

The vehicle is stopped on a steep hill and

there is a possibility of moving backward,

even if the electronic parking brake is

applied.

This warning appears when the Four-Wheel

Drive (4WD)/All-Wheel Drive (AWD) system is not

functioning properly while the engine is run-

ning. Reduce vehicle speed and have your

vehicle checked by a NISSAN dealer. See “4WD

warning” (P.5-30) or “Intelligent 4x4 (if equipped

for Korea)” (P.5-33).

.

This warning appears if the vehicle moves

while the automatic brake hold is activated.

28. Headlight system fault warning (if equipped)

This warning appears if the LED headlights are

malfunctioning. Have the system checked by a

NISSAN dealer.

33. Time for a driver break? indicator (if equipped)

This indicator appears when the set “Time for a

driver break?” indicator activates. You can set

the time for up to 6 hours.

22-23. 4WD/AWD High Temp. Stop ve-

hicle warning (if equipped)

29. Power will turn off to save the battery warning

This warning appears after a period of time if

the shift lever has not moved from the “P” (Park)

position while the ignition switch is in the “ON”

position for a certain period of time.

This warning may appear while trying to free a

stuck vehicle due to increased oil temperature.

The driving mode may change to Two-Wheel

Drive (2WD). If this warning is displayed, stop the

vehicle with the engine idling, as soon as it is

safe to do so. Then if the warning turns off, you

can continue driving. See “4WD warning” (P.5-

30) or “Intelligent 4x4 (if equipped for Korea)”

(P.5-33).

34. Take a break? indicator (if equipped)

This indicator appears when the set “Take a

break?” indicator activates. You can set the

time for up to 6 hours.

30. Power turned off to save the battery warning

This warning appears after the ignition switch

is automatically turned “OFF” to save the

battery.

35. Low outside temperature warning

(if equipped)

This warning appears if the outside tempera-

ture is below 3°C (37°F). The warning can be set

not to be displayed.

31. Turn off headlights warning

24–25. Tyre size incorrect warning (if equipped)

This warning appears when the driver side

door is opened with the headlight switch is left

ON and the ignition switch is placed in the “OFF”

or “LOCK” position. Place the headlight switch in

“OFF” or “AUTO” (if equipped) position. For

additional information, see “Headlight and turn

signal switch” (P.2-43).

This warning may appear if there is a large

difference between the diameters of the front

and rear wheels and tires. Pull off the road in a

safe area, with the engine idling. Check that all

the tire sizes are the same, that the tire

pressure is correct and that the tires are not

excessively worn. See “4WD warning” (P.5-30) or

“Intelligent 4x4 (if equipped for Korea)” (P.5-33).

36. Chassis control system fault warning

This warning appears if the chassis control

module detects an error in the chassis control

system. Have the system checked by a NISSAN

dealer. (See “Chassis control” (P.5-36).)

Instruments and controls 2-33

37. Speed limiter indicator (if equipped)

This indicator shows the speed limiter system

status. The status is shown by the color.

42. CVT/DCT System Fault warning (for

Continuously Variable Transmission (CVT)/

Dual Clutch Transmission (DCT) models)

48. Adaptive Front lighting System

(AFS) warning (if equipped)

This warning appears when the Adaptive Front

lighting System (AFS) is not functioning prop-

erly. Have the system checked by a NISSAN

dealer. (See “Adaptive Front lighting System

(AFS)” (P.2-54).)

For more details, see “Speed limiter” (P.5-60).

This warning appears when there is a malfunc-

tion with the CVT/DCT system. If this warning

38. Cruise indicator (if equipped)

This indicator shows the cruise control system

status. The status is shown by the color.

comes on, have the system checked by

NISSAN dealer.

a

49. Intelligent Cruise Control (ICC) sys-

tem ON indicator (if equipped)

This indicator shows the Intelligent Cruise

Control (ICC) system status. The status is

shown by the color. (See “Intelligent Cruise

Control (ICC)” (P.5-64).)

43. Navigation indicator (if equipped)

This indicator appears when a corner point is

coming.

See “Cruise control” (P.5-62) for details.

39. Continuously Variable Transmission

(CVT)/Dual Clutch Transmission (DCT)

position indicator (for CVT/DCT models)

This indicator shows the automatic shift posi-

tion.

44. Stop/Start System or Idling Stop

System indicator (if equipped)

This indicator shows the Stop/Start System or

Idling Stop System status. See “Stop/Start

System or Idling Stop System” (P.5-24).

50. System fault warning (if equipped)

This indicator shows the status of the following

systems if the vehicle is equipped with them.

In the manual shift mode, when the transmis-

sion does not shift to the selected gear due to a

transmission protection mode, the CVT/DCT

position indicator will blink and a chime will

sound.

45. System fault warning (if equipped)

This warning appears when the Intelligent

Driver Alertness system malfunctions.

.

Lane Departure Warning (LDW)

Intelligent Lane Intervention

Blind Spot Warning (BSW)

See “Driving with Continuously Variable Trans-

mission (CVT)/Driving with Dual Clutch Trans-

mission (DCT)” (P.5-19) for further details.

For more details, see “Intelligent Driver Alert-

ness” (P.2-40).

Rear Cross Traffic Alert (RCTA)

Intelligent Emergency Braking

Intelligent Emergency Braking with pedes-

trian detection

46. System fault warning (if equipped)

This warning appears when the Traffic Sign

Recognition system malfunctions.

40. SPORT mode system indicator (if equipped)

For more details, “Lane Departure Warning

(LDW)” (P.5-40), “Intelligent Lane Intervention”

(P.5-44), “Blind Spot Warning (BSW)” (P.5-49),

“Rear Cross Traffic Alert (RCTA)” (P.5-55), “In-

telligent Emergency Braking” (P.5-78) or “Intel-

ligent Emergency Braking with pedestrian

detection system” (P.5-83).

The SPORT mode indicator appears when the

SPORT mode system is turned on.

For more details, see “Traffic Sign Recognition”

(P.2-41).

(See “SPORT mode system (for Korea)” (P.5-91).)

41. ECO mode system indicator (if equipped)

47. Parking Sensor System Fault warn-

ing (if equipped)

The ECO mode indicator appears when the

ECO mode system is turned on.

This warning illuminates when there is

a

(See “ECO mode system” (P.5-91).)

problem with the parking sensor system. If this

warning comes on, have the system checked

by a NISSAN dealer.

2-34 Instruments and controls

51. Not available Front radar obstructed

warning (if equipped)

54. Not available warning (if equipped)

59. Exhaust filter maintenance warning

(if equipped)

This message appears when the Intelligent

Lane Intervention system becomes unavailable

because the VDC/ESP is turned off. For more

details, “Intelligent Lane Intervention” (P.5-44).

This message appears when the Intelligent

Cruise Control (ICC) system or Intelligent Emer-

gency Braking system becomes unavailable

because the front radar is obstructed. For more

details, see “Intelligent Cruise Control (ICC)” (P.5-

64), “Intelligent Emergency Braking” (P.5-78) or

“Intelligent Emergency Braking with pedestrian

detection system” (P.5-83).

If your vehicle is fitted with a gasoline engine,

your vehicle may also be fitted with a Gasoline

Particulate Filter (GPF). Under certain less-

favorable driving conditions, the GPF may

become saturated or clogged because these

driving conditions prevent automatic regen-

eration of the filter. In this case, a warning

message will be displayed in the vehicle in-

formation display. For additional details, see

“Gasoline Particulate Filter (GPF)” (P.5-9).

55. Not available High cabin tempera-

ture warning (if equipped)

This message appears when the camera de-

tects an interior temperature of more than

approximately 40°C (104°F). For more details,

see “Traffic Sign Recognition” (P.2-41), “Lane

Departure Warning (LDW)” (P.5-40) or “Intelli-

gent Lane Intervention” (P.5-44).

52. Not available Side radar obstructed

warning (if equipped)

60. Press brake to operate switch

warning (if equipped)

This message appears when the Blind Spot

Warning (BSW)/Rear Cross Traffic Alert (RCTA)

system becomes unavailable because a radar

blockage is detected. For more details, see

“Blind Spot Warning (BSW)” (P.5-49) or “Rear

Cross Traffic Alert (RCTA)” (P.5-55).

56. AdBlue status (if equipped)

This warning appears if the automatic brake

hold switch is pushed without depressing the

brake pedal while the automatic brake hold

function is activated. Depress the brake pedal

and push the switch to deactivate the auto-

matic brake hold function. For more details, see

“Automatic brake hold” (P.3-42).

This indicator appears if there are no system

malfunctions present in the AdBlue® Selective

Catalytic Reduction (SCR) system. See “AdBlue®

status” (P.5-6).

53. Not available Poor Road Conditions

warning (if equipped)

57. AdBlue warning (if equipped)

This warning appears when the AdBlue® level in

the tank is getting low or there is a malfunction

in the AdBlue® Selective Catalytic Reduction

(SCR) system. See “AdBlue® warning display”

(P.5-6).

This warning appears when the Intelligent Lane

Intervention system or Intelligent Cruise Con-

trol (ICC) system is temporarily not available

when the system detects that road conditions

may not be suitable for the system. The

Intelligent Lane Intervention system/ICC sys-

tem will also turn off. For more details, “In-

telligent Lane Intervention” (P.5-44) or

“Intelligent Cruise Control (ICC)” (P.5-64).

61. Caution Steep slope indicator (if equipped)

This indicator appears when the automatic

brake hold function is activated while the

vehicle is on a steep hill.

58. Exhaust filter full warning (if equipped)

62. Steep Slope Apply foot brake in-

dicator (if equipped)

If your vehicle is fitted with a diesel engine, your

vehicle may also be fitted with a Diesel Parti-

culate Filter (DPF). Under certain less-favorable

driving conditions, the DPF may become satu-

rated or clogged because these driving condi-

tions prevent automatic regeneration of the

filter. In this case, a warning message will be

displayed in the vehicle information display. For

additional details, see “Diesel Particulate Filter

(DPF)” (P.5-8).

This indicator appears if “Caution steep slope”

indicator has appeared over about 3 minutes.

Then, the electronic parking brake will auto-

matically be applied and the brake force of the

automatic brake hold will be released, and

vehicle may move or roll away unexpectedly.

Apply the foot brake to stop the vehicle

moving.

Instruments and controls 2-35

oil change, oil level indication and malfunction

of oil level sensor.

OIL CONTROL SYSTEM (if equipped)

4. Oil level sensor warning

If the oil sensor warning is displayed, the engine

oil level sensor may be malfunctioning. Contact

a NISSAN dealer immediately.

1. Distance to oil change

The distance to oil change is displayed if the

distance to oil change is less than 1,500 km

(930 miles).

2. Oil replacement indicator

When the set mileage approaches, the engine

oil replacement indicator will appear on the

display. After the oil is changed, reset the

distance to oil change. The oil replacement

indicator will not be reset automatically. To

reset this indicator, see “Settings” (P.2-22).

The distance to oil change interval cannot be

adjusted manually. The distance to oil change

interval is set automatically.

CAUTION:

If the oil replacement indicator is displayed,

change the engine oil as soon as possible.

Operating your vehicle with deteriorated oil

can damage the engine.

3. Low level reminder

If the low level indicator is displayed, the engine

oil level is low. If the low level reminder is

displayed, check the level using the engine oil

dipstick. (See “Engine oil” (P.8-13).)

CAUTION:

The oil level should be checked regularly

using the engine oil dipstick. Operating with

an insufficient amount of oil can damage the

engine and such damage is not covered by

the warranty.

JVI1312X

Example

When the ignition switch is in the “ON” position,

engine oil information is displayed.

Engine oil information informs the distance to

2-36 Instruments and controls

TRIP COMPUTER

WAC0596X

Instruments and controls 2-37

detection system” (P.5-83).

3. Average speed 1 and 2 (km/h or MPH)

(if equipped)

The average speed 1 mode shows the average

vehicle speed since the last reset. The average

speed 2 mode shows the average vehicle speed

since the time the ignition switch was turned

2. Speed and Average speed 1 and 2

(km/h or MPH) (if equipped)

The (digital) speed shows the current speed at

which the vehicle is travelling.

The average speed 1 mode shows the average

vehicle speed since the last reset. The average

speed 2 mode shows the average vehicle speed

since the time the ignition switch was turned

“ON”. The average speed

reset each time the ignition switch is placed

in the “OFF” position.

2

is automatically

Resetting is done by pushing the OK button.

When the OK button is pushed, the following

menu items are displayed.

“ON”. The average speed

2

is automatically

JVI1566X

reset each time the ignition switch is placed

in the “OFF” position.

The trip computer display can be changed

using the buttons located on the left side of

the steering wheel.

.

Cancel

Resetting is done by pushing the OK button.

When the OK button is pushed, the following

menu items are displayed.

— Return to the previous screen without

resetting.

OK - changes or selects an item in the trip

computer display

.

Average speed

.

Cancel

— Reset the average speed.

All

- navigates through the items in trip

computer display

— Return to the previous screen without

resetting.

— Reset all items of “Average Speed”,

“Elapsed time and trip odometer” and

“Fuel economy”.

.

Average speed

- goes back to the previous menu

— Reset the average speed.

All

- changes from one display

screen to the previous or next screen.

Once the “Average speed 1” is displayed, you

can use buttons to switch between the

“Average speed 1” and “Average speed 2”.

— Reset all items of “Average Speed”,

“Elapsed time and trip odometer” and

“Fuel economy”.

The displays shown in the illustration and

icons/messages in the vehicle information dis-

play may differ depending on the model.

The display is updated every 30 seconds. The

first 30 seconds after a reset, the display shows

“——”.

Once the “Average speed 1” is displayed, you

can use buttons to switch between the

“Average speed 1” and “Average speed 2”.

1. Safety Shield (if equipped)

The driving aids mode shows the operating

condition for the following systems.

4. Elapsed time and trip odometer 1 and

2 (km or mile)

The display is updated every 30 seconds. The

first 30 seconds after a reset, the display shows

“—–”.

.

Lane Departure Warning (LDW) (if equipped)

Intelligent Lane Intervention (if equipped)

Blind Spot Warning (BSW) (if equipped)

Intelligent Emergency Braking (if equipped)

Elapsed time:

The elapsed time 1 mode shows the time since

the last reset. The elapsed time 2 mode shows

the elapsed time since the time the ignition

switch was placed in the “ON”. (The trip

odometer is also reset at the same time.)

For more details, see “Lane Departure Warning

(LDW)” (P.5-40), “Intelligent Lane Intervention”

(P.5-44), “Blind Spot Warning (BSW)” (P.5-49),

“Intelligent Emergency Braking” (P.5-78) or “In-

telligent Emergency Braking with pedestrian

2-38 Instruments and controls

Trip odometer:

6-7. Fuel economy/ECO pedal guide 1

and 2 (l (liter)/100 km, km/l (liter) or MPG)

8. Audio (if equipped)

The audio mode shows the status of audio

information.

The trip odometer 1 mode shows the total

distance the vehicle has been driven since the

last reset. The trip odometer 2 mode shows the

total distance the vehicle has been driven since

the time the ignition switch was placed in the

“ON”. (The elapsed time is also reset at the same

time.)

Current fuel consumption:

The current fuel consumption mode shows the

current fuel consumption.

9. Navigation (if equipped)

When the route guidance is set in the Naviga-

tion System, this item shows the navigation

route information.

Average fuel consumption:

The average fuel consumption 1 mode shows

the average fuel consumption since the last

reset. The average fuel consumption 2 mode

shows the average fuel consumption since the

time the ignition switch was turned “ON”. The

average fuel consumption 2 is automatically

reset each time the ignition switch is placed in

the “OFF” position.

The elapsed time 2 and trip odometer 2 is

automatically reset each time the ignition

switch is placed in the “OFF” position.

10. Compass (if equipped)

This display indicates the heading direction of

the vehicle.

Resetting is done by pushing the OK button.

When the OK button is pushed, the following

menu items are displayed.

11. Intelligent 4x4 torque distribution

display (if equipped)

When the Intelligent 4x4 torque distribution

display is selected, you can view the distribu-

tion ratio of the transmission torque to the

front and rear wheels during driving.

.

Cancel

Resetting is done by pushing the OK button.

When the OK button is pushed, the following

menu items are displayed.

— Return to the previous screen without

resetting.

Distance

.

Cancel

— Reset the elapsed time and trip od-

ometer.

— Return to the previous screen without

resetting.

12. Chassis control

All

When Intelligent Trace Control, Intelligent En-

gine Brake or Intelligent Ride Control system is

operated, it shows the operating condition. It

also shows operating condition of Hill Start

Assist or the Hill Descent Control. The operating

condition of the automatic brake hold system

(if equipped) is also shown. See “Intelligent

Trace Control” (P.5-36), “Intelligent Engine Brake

(Continuously Variable Transmission (CVT)/

Dual Clutch Transmission (DCT) models)” (P.5-

37), “Intelligent Ride Control” (P.5-38), “Hill Start

Assist system” (P.5-39), “Hill descent control

system” (P.5-39) or “Automatic brake hold”

(P.3-42) for more details.

.

Fuel economy

— Reset all items of “Average Speed”,

“Elapsed time and trip odometer” and

“Fuel economy”.

— Reset the fuel economy.

All

Once the “Elapsed time and trip odometer 1” is

displayed, you can use buttons to switch

between the “Elapsed time and trip odometer 1”

and “Elapsed time and trip odometer 2”.

— Reset all items of “Average Speed”,

“Elapsed time and trip odometer” and

“Fuel economy”.

Once the “Fuel economy 1” is displayed, you can

use buttons to switch between the “Fuel

economy 1” and “Fuel economy 2”.

5. Intelligent Cruise Control (ICC) (if equipped)

This display indicates the operation condition

of the Intelligent Cruise Control (ICC) system.

The display is updated every 30 seconds. For

about the first 500 m (1/3 mile) after a reset, the

display shows “——”.

see “Intelligent Cruise Control (ICC)” (P.5-64) for

more details.

Instruments and controls 2-39

Instruments and controls -> Vehicle information display for Your Nissan X Trail SUV Fourth Generation (2022-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals