READY TO SET OFF -> Cruise Control for Your Peugeot Bipper Van First Generation (2007-2018)

Steering mounted controls  
When the system is activated, the "Cruise  
control" warning lamp comes on in the  
instrument panel.  
Temporarily exceeding  
of the speed  
It is possible to accelerate  
and drive momentarily at  
a speed greater than the  
programmed speed (for example to overtake  
another vehicle).  
When the accelerator pedal is released, the  
vehicle will return to the programmed speed.  
Deactivation  
Selecting the function  
-
Press the button on  
the end of the control.  
-
Place the ring in the  
ON position. the cruise  
control is selected but  
is not yet active and  
no speed has been  
programmed.  
CRUISE CONTROL  
or  
-
Press the brake or clutch pedal.  
"this is the speed at which the driver wishes  
to drive".  
the cruise control is also deactivated if the  
ABS or DSC system is invoked.  
this aid to driving in free-flowing traffic  
enables the vehicle to maintain the speed  
programmed by the driver, without use of the  
accelerator pedal.  
First activation /  
Programming  
a speed  
Reactivation  
-
Press the button on the  
end of the control again.  
-
Reach the chosen  
speed by pressing the  
accelerator.  
In order for it to be programmed or  
activated, the vehicle speed must be greater  
than 18 mph (30 km/h) with at least second  
gear engaged on the manual gearbox.  
or  
-
Press the accelerator pedal until a speed  
close to the programmed speed.  
-
Move the control up (+) for at least one  
second then release it.  
-
engage the gear selected when  
programming the speed.  
this programmes the reference speed. You  
can release the accelerator pedal, and the  
vehicle will maintain this speed.  
Your vehicle will return to the last  
programmed speed.  
3
Steering mounted controls  
Changing the programmed speed  
Cancelling the programmed speed  
there are two methods of memorising a  
speed higher than the previous one:  
Without using the  
When the vehicle becomes stationary, after  
switching off the ignition, the system no  
longer memorises a speed.  
accelerator:  
Operating fault  
-
move the control up (+).  
In the event of an operating fault, turn the  
ring to the OFF position and contact a  
PeugeOt dealer or a qualified workshop.  
each brief press increases  
the speed by 1 mph (km/h).  
A maintained press increases the speed  
gradually.  
Good practice  
using the accelerator:  
When changing the programmed speed by  
means of a maintained press, pay attention  
as the speed can increase or decrease  
rapidly.  
Do not use the cruise control on slippery  
roads or in heavy traffic.  
FIXED SPEED LIMITER  
-
exceed the memorised speed until the  
speed required is reached,  
This function allows a fixed maximum speed  
limit to be set for the vehicle (according  
to version and only on the 1.3 HDi 75 hp  
engine).  
the maximum speed can be set to one of  
4 pre-defined values: 56, 62, 68 or 80 mph  
(90, 100, 110 or 130 km/h).  
-
move the control up (+) for at least one  
second, then release it.  
to memorise a speed lower  
than the previous one:  
Never engage neutral while the system is  
operating.  
-
move the control  
down (-); the new speed  
will be memorised  
automatically.  
In the event of a steep slope, the cruise  
control cannot prevent the vehicle from  
exceeding the programmed speed.  
In any event, the cruise control cannot  
replace the need to observe the speed limits,  
nor can it replace the need for vigilance and  
responsibility on the part of the driver.  
It is advisable to leave your feet near the  
pedals.  
A label in the passenger compartment  
indicates the presence of this function  
and its setting.  
A brief press decreases the speed by 1 mph (km/h).  
A maintained press decreases the speed gradually.  
this function cannot be deactivated or set  
by the driver.  
Switching the function off  
-
Place the ring in the  
OFF position or switch  
off the ignition to switch  
everything off.  
to avoid any jamming under the pedals:  
-
ensure that the mat and its fixings on the  
floor are positioned correctly,  
-
never place one mat on top of another.