Get Getting to know your Vehicle -> Exterior lighting and signals Guide for Renault Captur SUV Second Generation (2019-2026)

EXTERIOR LIGHTING AND SIGNALS (1/6)

Depending on the vehicle, the dipped

beam headlights will appear automati-

cally after several sweeps of the wind-

screen wiper blades.

2

1

3

Side lights

Turn ring 2 until the symbol is

opposite mark 3.

Dipped beam

headlights

š

k

Manual operation

Turn ring 2 until the symbol is opposite

mark 3. This indicator light on the in-

strument panel comes on.

This indicator light on the instrument

panel comes on.

Before driving at night,

check that the electrical

equipment is operating cor-

Daytime running lights

function

Automatic operation

(depending on the vehicle)

rectly and adjust the head-

Turn ring 2 until the AUTO symbol is op-

posite mark 3: with the engine running,

the dipped beam headlights switch on

or off automatically depending on the

brightness of the light outside, without

any action on stalk 1.

light beams (if your vehicle is not

carrying its normal load).➥ 1.100.As

a general precaution, check that

the lights are not obscured (by dirt,

mud, snow or objects being trans-

ported).

The daytime running lights come on

automatically with no action on stalk 1

when the engine is started, and they go

off once the engine is switched off.

1.93

EXTERIOR LIGHTING AND SIGNALS (2/6)

During deactivation of the main beam

headlights, the dipped beam headlights

return to their original position.

The main beam headlights come on au-

tomatically if:

– exterior light is weak;

2

1

– no other vehicles or lighting are de-

tected;

– the vehicle speed is above approxi-

mately 25 mph (40 km/h).

Automatic main beam

headlights



Depending on the vehicle, this system

switches the main beam headlights on

and off automatically. It uses a camera

located behind the interior rear-view

mirror to detect vehicles that are being

followed and those coming in the oppo-

site direction.

If any of the above conditions are not

fulfilled, the system switches to dipped

beam headlights.

3

Note: make sure the windscreen is not

obscured (dirt, mud, snow, condensa-

tion etc.).

To activate automatic main beam

headlights:

Main beam headlights

With the engine running and

the dipped beam headlights lit, push

stalk 1. This indicator light on the instru-

ment panel comes on.

To return to the dipped headlight posi-

tion, pull stalk 1 towards you again.

á

turn ring 2 until the symbol AUTO is

Warning light

strument panel.

^{opposite mark}^{3 and push the stalk 1.}

comes on the in-

The system may encounter difficul-

ties under certain conditions, inclu-

ding:

– extreme weather conditions (rain,

snow, fog, etc.);

– obstruction in front of the wind-

screen or camera;

“Raise lights during driving”

function

When the main beam headlights are

activated, the “Raise lights during driv-

ing” function improves driver visibil-

ity by automatically raising the dipped

beam headlight and the main beam

headlights.

– when a following or oncoming ve-

hicle has weak or hidden lighting;

– incorrect settings for the front

headlights;

– reflective systems;

– ...

1.94

EXTERIOR LIGHTING AND SIGNALS (3/6)

Operating faults

2

1

When the message “Check Automatic

Lighting” appears on the instrument

panel, the system is deactivated.

Consult an approved dealer.

3

Using the portable naviga-

tion system at night in the

windscreen area below the

camera may disturb the op-

eration of the “automatic main beam

headlights” system (risk of reflection

on the windscreen).

Automatic main beam

headlights (continued)



To deactivate automatic main beam

headlights:

– turn ring 2 to a position other than

AUTO;

or

– pull the stalk 1.

The “automatic main beam

headlights” system should

under no circumstances be

Warning light

strument panel.



goes out on the in-

used to replace driver atten-

Note: the main beam headlights will be

activated upon deactivation of the au-

tomatic main beam headlights function.

tion and responsibility with regard

to vehicle lighting and adapting to

light, visibility and traffic conditions.

1.95

EXTERIOR LIGHTING AND SIGNALS (4/6)

Lights-on reminder buzzer

Welcome and goodbye

function

(depending on the vehicle)

2

If the lights are on after the engine is

switched off, a warning beep sounds

when the driver’s door is opened to

warn you that the lights are still on.

Once the function is activated, the day-

time running lights and the rear side

lights will light up automatically upon

detection of the card or when the vehi-

cle is unlocked.

Operating faults

If the “Check lighting” message ap-

^{pears with the}© warning light and

They switch off automatically:

– approximately one minute after light-

ing up;

the

k

warning light flashes on the

instrument panel, this indicates a light-

ing fault.

– when starting the engine based on

the position of the lighting stalk;

Consult an authorised dealer.

or

Switching off the lights

Depending on the vehicle:

– manually move ring 2 to position 0;

or

– upon locking the vehicle.

Activating/deactivating the

function

– the lights will go out automatically

when the engine is switched off, the

driver’s door is opened or the vehicle

is locked. In this case, the next time

the engine is started the lights will be

switched back on according to the

position of the ring 2.

For activation or deactivation of the ex-

ternal reception, refer to the multimedia

manual.

Select ON or OFF.

Note: if the fog lights are lit, the lights

are not switched off automatically.

1.96

EXTERIOR LIGHTING AND SIGNALS (5/6)

With the engine and lights switched

2

off, the 2 ring in AUTO position (or, de-

pending on the vehicle, in 0 position)

pull the stalk 1 towards you: the side

lights and dipped beam headlights will

switch on for approximately 30 seconds

1

along with the

ing lights on the instrument panel.

š

and

k

warn-

To increase this duration, you may pull

the stalk up to four times (total time re-

stricted to approximately two minutes).

On the instrument panel, the message

“lighting on _ _ _” followed by the re-

maining time will appear as confirma-

tion. You can then lock your vehicle.

“See-me-home lighting”

function

This function enables you to briefly

switch on the side lights and dipped

beam headlights (e.g. to provide light

when opening a gate).

To switch off the lights before they

switch off automatically, turn the 2 ring

to any position then return it to AUTO

position (or, depending on the vehicle,

to 0 position).

1.97

EXTERIOR LIGHTING AND SIGNALS (6/6)

Switching off the lights

2

1

Turn the centre ring 4again until the 3

symbol is opposite the symbol for the

fog lights. The corresponding indicator

light on the instrument panel goes out.

3

4

The rear fog lights switch off when the

exterior lights are switched off.

Rear fog lights

Turn centre ring 4 on the stalk

until the symbol faces mark 3, then re-



lease it.

Operation of the fog lights depends on

the exterior lighting selected, and an in-

dicator light will light up on the instru-

ment panel.

When driving in fog or snow, or

when transporting objects which are

higher than the roof, the headlights

do not come on automatically.

Do not forget to switch off the fog lights

when they are no longer needed, to

avoid inconveniencing other road

users.

Switching on the fog lights remains

the responsibility of the driver: the

indicator lights on the instrument

panel inform you whether the fog

lights are lit (indicator light on) or not

(indicator light not on).

1.98

Getting to know your Vehicle -> Exterior lighting and signals for Your Renault Captur SUV Second Generation (2019-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals