Get Getting to know your Vehicle -> Seat belts Guide for Renault Captur SUV Second Generation (2019-2026)

SEAT BELTS (1/5)

Always wear your seat belt when trav-

elling in your vehicle. You must also

comply with the legislation of the par-

ticular country you are in.

Adjusting your driving

position

– Sit well back in your seat (having

first removed your coat or jacket).

This is essential to ensure your back

is positioned correctly;

Before starting, first adjust your driv-

ing position, then ask all occupants

to adjust their seat belts to ensure

optimum protection.

– adjust the distance between the

seat and the pedals. Your seat

should be as far back as possible

while still allowing you to fully de-

press the pedals. The seatback

should be adjusted so that your arms

are slightly bent when you hold the

steering wheel;

Make sure that the rear bench seat

is locked in position correctly so that

the rear seat belts will operate cor-

rectly. ➥ 3.35.

– adjust the position of your head-

rest. For maximum safety, your head

must be as close as possible to the

headrest;

Incorrectly adjusted or

twisted seat belts may

cause injuries in the event

of an accident.

– adjust the height of the seat. This

adjustment allows you to select the

seat position which offers you the

best possible view;

Use one seat belt per person,

whether child or adult.

– adjust the position of the steering

wheel.

Even pregnant women should wear

a seat belt. In this case, ensure that

the lap belt is not exerting too much

pressure on the abdomen, but do

not allow any slack.

1.23

SEAT BELTS (2/5)

– move the shoulder strap 1 as close

as possible to the base of the neck

without it actually resting against it

(if necessary, adjust the height of the

seat belt if available) and make sure

that the chest strap 1 is in contact

with the shoulder;

Locking

Unwind the belt slowly and smoothly

and ensure that buckle 3 locks into

catch 5 (check that it is locked by pull-

ing on buckle 3).

If the belt jams, allow it to return slightly

before attempting to unwind it again.

– position the lap belt 2 so that it lies

flat on the thighs and against the

pelvis.

If your seat belt is completely jammed,

pull slowly, but firmly, so that just over

3 cm unwinds. Allow it to return slightly

before attempting to unwind it again.

The belt should be worn so that it is

as close as possible to your body, i.e.:

avoid wearing heavy clothing or keep-

ing bulky objects under the belts, etc.

If there is still a problem, contact an ap-

proved dealer.

Adjusting the seat belts

Unlocking

For correct adjustment and positioning

of the seat belts at all seats:

Press button 4 and the seat belt will be

rewound by the inertia reel. Guide the

belt.

– adjust the seats (seat position and

seatback angle if available);

– sit with your back firmly against the

seatback;

1.24

SEAT BELTS (3/5)

Driver’s seat belt reminder

and, depending on the vehi-

cle, front passenger seat belt re-

minder

It is accompanied by the 6 symbol which

appears for approximately 60 seconds

each time one of the rear seat belts is

fastened or unfastened.

This appears on the central display

when the ignition is switched on and

if the driver’s and/or front passenger’s

seat belt(s) (if the passenger seat is

occupied) is not fastened. Depending

on the vehicle, if the seat is occupied

and one of these seat belts is not fas-

tened or becomes unfastened while

the vehicle is moving at a speed over

approximately 12 mph (20 km/h), the

When the vehicle speed reaches or ex-

ceeds 12 mph (20 km/h), if one of the

rear seat belts is or becomes unfas-

tened during the journey:

– the

the central display;

™

warning light flashes on

and

– a beep is emitted for 30 to 120 sec-

onds (depending on the version);

™

warning light flashes and a beep

sounds for approximately 120 seconds.

and

playback of 6 graphic:

– indicator green: seatbelt fastened;

– indicator in red: the seat is occupied

and the seat belt is not fastened;

– indicator grey: seat not occupied.

– the 6 symbol is displayed for at least

approximately 60 seconds and

the symbol for the seat concerned

changes to red.

Note: an object placed on the passen-

ger seat may activate the warning light

in some cases, depending on the ve-

hicle.

Always make sure that the rear pas-

sengers are properly fastened and that

the number of fastened seat belts in-

dicated corresponds to the number of

rear seats occupied.

Depending on the vehicle, the

™

Rear seat belt reminder (depending

on the vehicle)

The 6 graphic is displayed on the in-

strument panel when the ignition is

switched on. This informs the driver of

the fastening status of each of the rear

seat belts every time:

– the ignition is switched on;

– a door is opened;

– fastening or unfastening of a rear

seat belt.

warning light on the central display also

appears when the ignition is switched

on, if a rear seat is occupied and the

seat belt is not fastened. When the ve-

hicle speed is less than approximately

Note: in some cases the alerts may be

activated if an object is placed on one

of the rear seats, depending on the ve-

hicle.

12 mph (20 km/h), the

light on the central display appears

when a rear seat belt is unfastened.

™

warning

1.25

SEAT BELTS (4/5)

Adjusting the height of the

front seat belts

Use button 7 to adjust the seat belt

height so that the shoulder strap is worn

as shown previously. Press the button 7

and raise or lower the seat belt. Make

sure that the seat belt is locked in posi-

tion correctly after you have adjusted it.

Rear side seat belts 8

The belts are locked, unlocked and

adjusted in the same way as the front

belts.

Rear centre seat belt

Slowly unwind belt 9.

Click buckle 10 into black catch 11.

Fasten the tongue 12 in the red

buckle 13.

Check that the rear seat

belts are positioned and

operating correctly each

time the rear bench seat is

moved.

Ensure that you always leave the

tongue 10 fastened in the buckle 11

even if no passenger is present in

the centre seat.

1.26

SEAT BELTS (5/5)

The following information applies to the vehicle’s front and rear seat belts.

– No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and

their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.

– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too

loosely may cause injury in the event of an accident.

– Never wear the shoulder strap under your arm or behind your back.

– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around

them.

– The belt should never be twisted.

– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as

they show any signs of wear.

– When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so that they

can be used properly.

– Make sure that the buckle is inserted into the appropriate catch.

– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly secured.

– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or ob-

jects).

1.27

Getting to know your Vehicle -> Seat belts for Your Renault Captur SUV Second Generation (2019-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals