Get Getting to know your vehicle -> Headrests - Seats Guide for Renault Scenic 4 Door Fourth Generation (2017-2022)

FRONT HEADRESTS

A

To adjust side supports B

Depending on the vehicle, sections B

can be adjusted independently to the

desired position.

B

3

To remove the headrest

Raise it to its highest position (tilt the

seatback backwards if necessary).

Press button 2 and lift the headrest to

release it.

1

2

To refit the headrest

Check that the headrest rods are

clean 3.

Insert the headrest rods into the holes 1

(tilt the seatback backwards if neces-

sary).

Lower the headrest until it locks, press

button 2 and lower the headrest as far

as it will go.

To raise the headrest

Pull the headrest upwards to the de-

sired height.

To lower the headrest

Press button 2 and guide the headrest

down to the desired height.

Check that the headrest is properly

locked in place.

The headrest is an impor-

tant safety component:

ensure that it is in place and

To adjust the angle of the

headrest

Depending on the vehicle, move sec-

tion A towards or away from you to the

required position.

in the correct position. The

distance between your head and the

headrest and the distance between

the head and section A should be

as small as possible.

1.20

FRONT SEATS WITH MANUAL CONTROL (1/3)

To tilt the seatback

Lift handle 3 and tilt the seatback to the

desired position. Release the handle at

the desired position and make sure that

it is locked.

2

1

3

Settings

To move the seat forwards or back

For safety reasons, make

these adjustments only

when the vehicle is station-

ary.

Lift and hold the handle 1 to unlock the

seat. Release the handle at the desired

position and make sure that it is locked.

To raise or lower the seat base

We would advise you not to recline

the seatbacks too far to ensure that

the effectiveness of the seat belts is

not reduced.

Move the lever 2 as many times as nec-

essary upwards or downwards until the

required position is reached.

Nothing should be placed on the

floor (area in front of driver) as such

objects may slide under the pedal

during braking manoeuvres, thus

obstructing its use.

1.21

FRONT SEATS WITH MANUAL CONTROL (2/3)

5

4

To adjust the seat’s lumbar position

Heated seats

Lower handle 4 to increase the support

With the ignition on:

and lift it to decrease it.

– pressing the switch 5 on the required

seat for the first time activates the

heating system at maximum power.

Both integrated switch warning lights

come on;

– a second press decreases the heat-

ing to minimum power. One inte-

grated warning light comes on;

– pressing for the third time turns the

heating off.

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

1.22

FRONT SEATS WITH MANUAL CONTROL (3/3)

When using the passenger seat in table

position, you must not use the two rear

seats immediately behind it.

Repositioning the seat

Make sure that nothing prevents the

seat from moving.

It is essential to pull the handle 7 to

raise the seatback. Ensure it is cor-

rectly locked in place.

7

Be sure to hold the seat-

back when placing the seat

in table position.

Risk of injury.

Table function

When the front seat is in

table position, the front pas-

senger airbag airbag must

be deactivated (see the in-

formation on “Child safety: activat-

ing/deactivating the front passenger

airbag” in Section 1).

Depending on the vehicle, the passen-

ger seatback may be folded down onto

the seat base to create a table.

– Lower the headrest;

– move the seat back;

– lower the seat base fully;

– pull the handle 7 and fully lower the

seatback.

Risk of serious injury caused by

items resting on the seatback table

which may be dislodged when the

airbagairbag is deployed.

The label (on the dashboard) and

the markings (on the windscreen)

remind you of these instructions.

For your safety, attach any

transported objects when

the seat is in the table po-

sition.

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

1.23

DRIVER’S SEAT WITH ELECTRIC CONTROLS (1/2)

Adjusting the seatback

To tilt the seatback, move the top of

switch 2 forwards or backwards.

Adjusting the lumbar support

on the seat

Move the switch 3 forwards, back-

wards, up or down.

2

1

3

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

On equipped vehicles, switch 1 grants

access to the seats menu on the multi-

function screen (please refer to the fol-

lowing pages).

Make sure that the seatbacks are

correctly locked in place.

We would advise you not to recline

the seatbacks too far to ensure that

the effectiveness of the seat belts is

not reduced.

No object should be placed on the

floor (in front of the driver). such

objects may slide under the pedals

during sudden braking manoeuvres

and obstruct their use.

Make sure that the seat-

backs are correctly locked

in place.

1.24

DRIVER’S SEAT WITH ELECTRIC CONTROLS (2/2)

Heated seats

With the ignition on:

– pressing the switch 6 on the rele-

vant seat for the first time activates

the heating system on high. Both in-

tegrated switch warning lights come

on. The system automatically de-

cides whether or not the heating is

needed;

4

6

– pressing the switch for the second

time changes the heating to low. One

integrated warning light comes on;

5

– pressing for the third time turns the

heating off.

Adjusting the seat position

To move the seat forwards or back

Move switch 4 forwards or backwards.

Adjusting the seat length

Lift handle 5 to unlock. Release the

handle at the desired position and

make sure that it is locked.

Operating faults

When an operating fault is detected,

the warning lights in the switch 6 for

the seat concerned flash or, depending

on the vehicle, switch off after approxi-

mately five seconds.

To raise or lower the seat base

Move the back of switch 4 up or down.

To tilt the seat base

(depending on the vehicle)

Move the front of switch 4 upwards or

downwards.

Consult an approved dealer

1.25

FRONT SEATS: Functions (1/3)

Browse menu “Driver” or “Passenger”

to:

Massage

Driver

Passenger

– select the type of massage (Tonic,

Relaxing or Lumbar);

Massage

ON

– adjust the intensity (+ or -);

– adjust the speed (+ or -);

Lumbar

Relaxing

Tonic

1

– reset the selected settings. Press 2

then “Reset”;

Intensity

– activate/deactivate the massage

seat (ON or OFF).

Speed

Note:

2

– the duration of the massage is ap-

proximately ten minutes. Then the

function is disabled automatically

(back in OFF position);

Using the multifunction screen, de-

pending on the vehicle you can access

a number of seat functions.

Massage

You can activate the driver and front

passenger seat massage function.

– the mode that you select in the

“Multi-Sense” menu may affect the

massage configuration (please refer

to the information on “Multi-Sense” in

Section 3);

On equipped vehicles, the switch 1 per-

mits direct access to the “Seats” menu

on the multifunction screen.

Using the multifunction screen,

select menu “Vehicle”, “Seats” then

“Massage”.

Please refer to the multimedia equip-

ment instructions for further informa-

tion.

– with the engine switched off, the

massage function will run just once.

1.26

FRONT SEATS: Functions (2/3)

Easy driver and passenger access

Press “ON” or “OFF” to activate or de-

activate this function.

Easy access driver

ON

Easy access passenger

ON

When this function is activated, the seat

moves backwards automatically as the

driver or passenger leaves the vehicle.

Courtesy for passenger

OFF

Position

3

The passenger seat returns to its origi-

nal position when the door is closed.

The driver’s seat returns to its origi-

nal position when you press the start

button with the door closed.

4

5

2

Courtesy for passenger

Settings

Press “ON” or “OFF” to activate or de-

activate this function.

Using the multifunction screen, select

menu “Vehicle”, “Seats” then “Settings”.

When this function is activated, the

driver can adjust the passenger seat

using switches 3, 4 and 5.

You can activate or deactivate the fol-

lowing elements:

– easy driver access;

– easy passenger access;

– Courtesy for passenger;

– visual feedback of current move-

ment.

1.27

FRONT SEATS: Functions (3/3)

Position

Visual feedback

It is possible to store the driving posi-

tion of the driver seat.

ON

3

The driving position includes all the

electric settings for the seat base and

seatback.

The driving position can be stored and

recalled by pressing the buttons:

3

– RENAULT hands-free card detected;

– when the driver’s door is opened.

4

Recall

Save

5

Storing your driving position

– Adjust the driver seat using

switches 3, 4 and 5 (refer to previous

page);

– from the multifunction screen, select

menu “Vehicle”, “Seats”, “Settings”

then “Position” and select “Save”.

Recalling the driving position

With the vehicle at a standstill, using

the multifunction screen, select menu

“Vehicle”, “Seats”, “Settings” then

“Position”, select “Recall” and confirm.

Note: recall of the saved driving po-

sition is interrupted if one of the seat

adjustment buttons is pressed during

recall.

The position of the driver is then stored.

When driving, it is not possible to

recall a driving position.

For safety reasons, carry

out any adjustments when

the vehicle is stationary.

1.28

Getting to know your vehicle -> Headrests - Seats for Your Renault Scenic 4 Door Fourth Generation (2017-2022)

Related Topics

Popular Owner Manuals

Latest Owner Manuals