2017-2022 Renault Scenic 4 Door Getting to know your vehicle -> Trip computer User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Getting to know your vehicle -> Trip computer for Your Renault Scenic 4 Door Fourth Generation (2017-2022)

TRIP COMPUTER: general information (1/2)  
Display selection keys 2  
1
Scroll through the following information  
by repeated short presses on button 2  
(the display depends on the vehicle  
equipment and country):  
3
2
2
a) total mileage and trip mileage re-  
corder;  
b) journey parameters:  
– average fuel consumption;  
– current fuel consumption;  
– Estimated range with remaining  
fuel;  
– distance travelled;  
– average speed;  
c) current speed;  
Trip computer and warning  
d) distance before service;  
e) reset the tyre pressure;  
system 1 or 3  
Depending on the vehicle, this includes  
the following functions:  
f) trip log, operating faults and informa-  
tion message readout;  
– distance travelled;  
g) Estimated range with remaining rea-  
gent.  
– journey parameters;  
– information messages;  
– operating fault messages (associ-  
ated with the © warning light);  
– warning messages (associated with  
the ® warning light);  
All these functions are described on the  
following pages.  
1.82  
ON-BOARD COMPUTER: general information (2/2)  
Interpreting some of the  
values displayed after  
resetting  
The values showing average fuel con-  
sumption and average speed will  
become more stable and reliable the  
further you have travelled since the last  
time the Reset button was pressed.  
The average fuel consumption may de-  
crease when:  
4
– the vehicle stops accelerating;  
– the engine reaches its operating  
temperature (if the engine was cold  
when the reset key was pressed);  
Trip mileage resetting  
– when driving from an urban area  
With “trip mileage recorder” selected  
on the display, press key OK 4 until the  
mileage recorder resets to zero.  
onto the open road.  
Automatic resetting of the  
journey parameters  
Resetting occurs automatically when  
the maximum value of any of the pa-  
rameters is exceeded.  
Resetting the journey  
parameters (reset button)  
with the display showing one of the trip  
settings, press key OK 4 until the dis-  
play is reset to zero.  
1.83  
ON-BOARD COMPUTER: trip settings (1/5)  
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  
Examples of selections  
Interpreting the display selected  
101778 km  
112.4 km  
a) Total mileage and trip mileage recorder.  
Average  
b) Journey parameters:  
Average fuel consumption.  
The value is displayed after having travelled at least 400 metres since the last  
reset.  
5.8 L/100  
Current  
Current fuel consumption.  
Value displayed after reaching a speed, depending on the vehicle, from 6.2 mph  
(10 km/h) to 18.6 mph (30 km/h).  
7.4 L/100  
1.84  
ON-BOARD COMPUTER: trip settings (2/5)  
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  
Examples of selections  
Interpreting the display selected  
Range  
b) Journey parameters (continued):  
Estimated range with remaining fuel.  
The value is displayed after driving 400 metres.  
541 km  
Distance  
522 km  
Distance travelled since last reset.  
Average  
Average speed since the last reset.  
The value is displayed after driving 400 metres.  
123.4 km/h  
c) Current speed.  
55.8 mph (90 km/h)  
1.85  
ON-BOARD COMPUTER: trip settings (3/5)  
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  
Examples of selections  
Interpreting the display selected  
On-board computer with mileage-  
before-service message  
d) Mileage before service or oil change.  
Mileage before service  
Service in  
SERVICE  
INTERVALS  
With the ignition switched on, the engine not running and  
the display set to “SERVICE INTERVALS”, press and hold the  
OK button for approximately 5 seconds to display the mileage  
before service (distance or time to the next service). When the  
distance value approaches its limit, there are several possible  
scenarios:  
30 000 km / 12 mo  
Service due in  
– range less than 930 miles (1,500 km) or one month: the  
message “Service due in” is displayed accompanied by the  
nearest term (distance or time);  
300 km / 24 days  
– range equal to 0 miles (0 km) or date of service reached:  
the message “Service required” is displayed accompanied by  
the warning light ©.  
Service required  
The vehicle requires a service as soon as possible.  
Reset: to reset the distance before the next service, press and hold button 2 for approximately 10 seconds until the display  
shows the mileage before service permanently.  
Note: If a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the  
event of an oil change, both the distance before the next service and the next oil change should be reset.  
1.86  
TRIP COMPUTER: trip settings (4/5)  
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  
Examples of selections  
Interpreting the display selected  
On-board computer with distance before  
next service message (cntd.)  
d) Mileage before service or oil change.  
Mileage before service  
Oil change in  
SERVICE  
With the ignition on, the engine not running and the display  
selected “ SERVICE INTERVALS “, press button OK for about  
5 seconds to display the mileage before the next service, then  
press the button 2 to view the mileage before the next oil change  
(distance or time remaining before the next service). When the  
distance value approaches its limit, there are several possible  
scenarios:  
– range less than 930 miles (1,500 km) or one month: the  
message “Service due in” is displayed accompanied by the  
nearest term (distance or time);  
INTERVALS  
30 000 km / 24 mo  
Service due in  
300 km / 24 days  
– range equal to 0 miles (0 km) or date of oil change reached:  
the message “Service required” is displayed accompanied by  
the warning light ©.  
Service required  
The vehicle requires an oil change as soon as possible.  
Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,  
door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can  
therefore decrease more quickly in some cases than the actual distance travelled.  
Resetting: to reset the mileage before a service, press and hold button 2 for approximately 10 seconds until the display shows  
the range permanently.  
NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the  
event of an oil change, both the distance before the next service and the next oil change should be reset.  
1.87  
ON-BOARD COMPUTER: trip settings (5/5)  
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  
Examples of selections  
Interpreting the display selected  
e) Reset the tyre pressure.  
Refer to the information on the “Tyre pressure  
monitoring system” in Section 2.  
+
Tyre pressure  
f) Trip log.  
No message  
memorised  
Successive display:  
– information messages (passenger airbag OFF  
etc.);  
– operating fault messages (Check injection  
system, etc.).  
g) Estimated range with remaining reagent.  
Top Up AdBlue  
before 2400 km  
Refer to the information on “Reagent tank” in  
Section 1.  
1.88  
TRIP COMPUTER AND WARNING SYSTEM: information messages  
These can help in the vehicle starting phase, or give information about a selection or a driving status.  
Examples of information messages are given in the following pages.  
Examples of messages  
“Parking brake on”  
Interpreting the display selected  
Indicates that the parking brake has been applied.  
“Checking control  
functions”  
Displayed with the ignition on when the vehicle is running self-diagnostics.  
“Turn steering  
wheel + START”  
Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steering  
column.  
“Steering wheel  
not locked”  
Indicates that the steering column has not been locked.  
1.89  
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages  
These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as  
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.  
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The  
© warning light stays on. Examples of operating fault messages are given in the following pages.  
Examples of messages  
“Clean diesel filter”  
Interpreting the display selected  
Indicates the presence of water in the diesel filter; contact an approved Dealer  
as soon as possible.  
“Check lighting”  
“Check vehicle”  
Indicates a fault in the headlights.  
Indicates a fault in one of the pedal sensors, battery management system or oil  
level sensor.  
“Check airbag”  
Indicates a fault in the restraint system in addition to the seat belts. In the event  
of an accident, it is possible that they may not be triggered.  
“Check anti- pollution system”  
– Indicates a fault in the vehicle’s particle filter system.  
– Indicates a fault in the emissions reduction system when it is accompanied  
by the  
Section 1.  
warning light. Refer to the information on “Reagent tank” in  
1.90  
TRIP COMPUTER AND WARNING SYSTEM: warning message  
These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traf-  
fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.  
Some examples of warning messages are given below. Note: the messages appear on the display either individually or al-  
ternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.  
Examples of messages  
“Engine failure hazard”  
Interpreting the display selected  
Indicates an injection fault, the vehicle’s engine has overheated or there is a  
serious engine fault.  
“Power steering fault”  
Indicates a fault in the steering system.  
“Braking system fault” or “Stop vehicle” Indicates a fault in the braking system. Apply the electronic parking brake ma-  
nually and ensure that the vehicle is immobilised using a chock.  
“Electric failure DANGER”  
“Puncture”  
Indicates a fault in the vehicle battery charging circuit (alternator etc.).  
Indicates a puncture on the tyre displayed on the instrument panel.  
1.91  

Related Topics

Getting to know your vehicle
Key, radio frequency remote control: general information, use The RENAULT card: general information and use Locking, unlocking the opening elements Opening and closing the doors Automatic locking when driving Steering wheel/Power-assisted steering Headrests - Seats Seat belts Additional methods of restraint: in addition to the front seat belts Additional methods of restraint: to the rear seat belts Additional methods of restraint: side protection Child safety: General information Choosing a child seat Choosing a child seat mounting Fitting a child seat, general information Child seats: attachment by seat belt or by Isofix system Driving position Instrument panel Vehicle settings customisation menu Clock and outdoor temperature Rear view mirrors Audible and visual signals Exterior lighting and signals Headlight beam adjustment Windscreen wash, wipe Rear windscreen wash, wiper Fuel tank (filling with fuel) Reagent tank

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot