Get Driving -> Gear control Guide for Renault Zoe 4 Door Third Generation (2019-2024)

GEAR CONTROL (1/3)

Operation

With the engine running READY mes-

sage lit on the instrument panel ➥ 2.2,

the gear control is automatically in N

position.

To exit position N, it is essential to de-

press the front brake pedal.

With your foot on the brake pedal

^{(warning light}c on display A goes

out), move the lever out of position N.

4: position accessible from the cur-

rent position by moving the selec-

tor lever 1 two notches forwards or

backwards.

Selector lever 1

R:reverse.

N:neutral.

D:moving off forwards normally.

B:moving off forwards with strong

regenerative braking.

The vehicle can only be started if

the charging cord is unplugged from

the vehicle.

The 3 or 4 symbols are displayed to in-

dicate the gears that can be selected. If

these symbols are absent this indicates

that the gears cannot be selected from

the current position.

The A indicator light displays the gear

engaged.

The following informative symbols may

appear on the instrument panel dis-

play B:

Obstructions to the driver

On the driver’s side, only

use mats suitable for the

The required gear will flash on the in-

strument panel if a gear is not acces-

sible from the engaged position of the

lever.

vehicle, attached with the

2: position of the gear engaged;

pre-fitted components, and check

the fitting regularly. Do not lay one

mat on top of another. There is a

risk of wedging the pedals

3: position accessible from the cur-

rent position by moving the selector

lever 1 one notch forwards or back-

wards;

2.5

GEAR CONTROL (2/3)

Driving in mode B

This mode allows driving with a more

dynamic regenerative mode. When

releasing the accelerator, the vehicle

uses regenerative braking to slow down

the vehicle. Thus the motor generates

higher electrical current which allows

the traction battery to be recharged.

When you select position B when the

vehicle is stationary, the vehicle moves

forward as soon as you release the

brake pedal (without pressing on the

accelerator pedal).

In B mode, the regenerative braking will

be reduced if the accumulator is cold or

completely charged.

One-touch selector

Driving in mode D

Move the selector lever 1 one or two

notches forwards or backwards to

engage the desired position (R, N, D

or B) then release the lever and it will

return to a stable position.

When you select position D when the

vehicle is stationary, the vehicle moves

forward as soon as you release the

brake pedal (without pressing on the

accelerator pedal).

While driving, press the accelerator

pedal to achieve the desired speed.

Move from D position to B or

B to D

To switch from one position to the other,

tilt the lever to one notch or two notches

backwards.

The selected position is displayed on

the instrument panel along with the 2

warning light in front of the position.

The selected position, lit up on the in-

strument panel, alongside warning

light 2, will confirm the position of the

gear control.

If certain conditions prevent shifting

from one position to another, the re-

quested position flashes on the instru-

ment panel.

The last selected position (B or D) is stored and will be the first of the two posi-

tions accessible from the current position N or R.

2.6

GEAR CONTROL (3/3)

To select reverse gear

Operating faults

With the vehicle stationary, engine run-

ning, Nposition, D or B engaged, de-

press the brake pedal and move for-

ward the lever by two notches, R lights

up on the instrument panel.

During driving:

– if the message “WARNING: Check

Gearbox” appears on the instrument

panel, this indicates a fault.

When the door is opened, the mes-

sage “Select NEUTRAL N” is dis-

played on the instrument panel

if the gear control is in a position

other than N and the engine is not

switched off.

Contact your approved Dealer as

soon as possible;

The reversing lights will illuminate as

soon as reverse gear is selected (igni-

tion on) and, depending on the vehicle,

the reversing camera ➥ 2.70.

– if the message “WARNING: Gearbox

Overheating” appears on the instru-

ment panel, stop as soon as possi-

ble to allow the gearbox to cool down

and wait for the message to disap-

pear.

Note: with the engine running, the ve-

hicle moving between 0 and 5 mph

(8 km/h) and position N or R engaged, it

is not necessary to depress the brake

pedal to engage the position D. This is

useful when parking manoeuvres re-

quire alternating forward and reverse

gearing.

In the event of an impact to

the underside of the vehicle

(e.g.: striking a post, raised

kerb or other street furni-

ture), this may result in damage to

the vehicle (e.g.: twisted axle), the

electrical circuit or the traction bat-

tery.

Do not touch the circuit elements or

any fluids or liquids.

Parking the vehicle

With the vehicle stationary, stop the

engine. Neutral position is engaged

and the electronic parking brake is ap-

plied automatically.

To prevent any risk of accident,

have your vehicle checked by an

authorised dealer.

Risk of serious injury or electric

shock and risk to life.

The N position of the lever

does not mechanically lock

the drive wheels, make

sure it is immobilised before

leaving the vehicle.

2.7

Driving -> Gear control for Your Renault Zoe 4 Door Third Generation (2019-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals