Get INSPECTION AND MAINTENANCE -> Bulb replacement Guide for Suzuki Jimny SUV Fourth Generation (2018-2026)

INSPECTION AND MAINTENANCE

Bulb replacement

_A CAUTION

Light bulbs can be hot enough to

burn your finger right after turning

off lights. This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

To avoid injury by sharp-edged

parts of the body, wear gloves and

a long-sleeved shirt when replacing

light bulbs.

NOTICE

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

NOTICE

Frequent bulb replacement indicates

the need for an inspection of the elec-

trical system. This should be carried

out by a SUZUKI dealer.

6-47

Headlights

LED type

Since special procedures are required, it is

recommended that you take your vehicle

to a SUZUKI dealer for light replacement.

Halogen type

78RB07025

(1) Bulb

8~'",,,

'\:~

(3) ~f I

r-,.t:: l'1

Jlilt10or\01 ~o

"-" [l!l

78RB07026

1) Open the engine hood while the engine

is stopped. Disconnect the coupler (2).

Remove the sealing rubber (3) by pull-

ing the grip (4).

78RB07027

2) Push the retaining spring (5) forward

and unhook it. Then remove the bulb.

Install a new bulb in the reverse order

of removal.

78RB07028

NOTE:

You can see the position of retaining

spring from the hole of headlight.

Front turn signal light and

front position light

For front LED position light (if equipped), it

is recommended that you take your vehicle

to a SUZUKI dealer for light replacement

since special procedures are required.

Vehicle with the halogen headlights

(1)

(1) Front turn signal light

(2) Front position light

78RB07029

INSPECTION AND MAINTENANCE

Vehicle with the LED headlights

(1)

(1) Front turn signal light

(2) Front LED position light

78RB07030

6-48

INSPECTION AND MAINTENANCE

68PH00732

1) Open the engine hood while the engine

is stopped. To remove the bulb holder

of the front turn signal light or the front

position light (for vehicle with halogen

headlights) from the light_ housing, turn

the holder counterclockw1se and pull 1t

out.

6-49

.(2)

Q(3)

78RB07051

(2) Removal

(3) Installation

2) To remove and install the bulb of the

front position light (1 ), simply pull out or

push in the bulb.

Side turn signal light

78RB07031

Since the bulb is built-in type, replace ii as

the light assembly. Remove the light

assembly by sliding the light housing left-

ward with your finger.

Front fog light (if equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the b~

6 light to be replaced to repla_ce the

easily. Then turn off the engine.

2) Remove the clips (1) and screw (2) at

the bottom of bumper. d

For removing the clip, use a _flat-blade

screwdriver as shown in the ,11ustrat1on.

78RB07033

3) Open the end of the cover inside the

fender.

52R70140

) Disconnect the coupler (3)

the lock release. Turn the u .

(4) counterclockwise and remove ,t.

INSPECTION AND MAINTENANCE

Daytime running light (if equipped)

Models without front fog light

78RB07034

6-50

INSPECTION AND MAINTENANCE

Models with front fog light

78RB07035

1) To approach the daytime running light,

open the end of the cover inside the

front fender. Refer to the procedure for

the bulb replacement of the "Front Fog

Light" in this section.

6-51

78RB07049

2) Disconnect the coupler by pushing the

lock release. Turn the bulb holder coun-

terclockwise and remove ii.

NOTE:

Depending on the vehicle's specification,

the daytime running light is located under

the front fog light, but the replace method

is same as the above.

Rear combination light

78RB07036

1) Remove the nuts (1) and pull the rear

combination light from the rear bumper

by pushing the hooks (A).

(2)

(4)(5)

78R807037

(2) Brake/tail light

(3) Rear turn signal light

(4) Reversing light

(5) Rear fog light (if equipped)

2) To remove the bulb holder of the above

light from the light housing, turn the

holder counterclockwise and pull it out.

(2) / (3) / (4) / (5)~ ,

.. (6)

Q(7)

78RB07038

(6) Removal

(7) Installation

3) To remove and install the bulb of the

brake/tail light (2), the rear turn signal

light (3), the reversing light (4), or the

rear fog light (5) (if equipped), simply

pull out or push in the bulb.

INSPECTION AND MAINTENANCE

License plate light

52RM70070

1) Remove the cover (1) by turning it

counterclockwise.

6-52

INSPECTION AND MAINTENANCE

76MH0A126

2) To remove and install the bulb of the

license plate light (2), simply pull out or

push in the bulb.

High-mount stop light

LED is used. It is recommended that you

take your vehicle to a SUZUKI dealer for

bulb replacement since special procedures

are required.

6-53

Interior light

Remove the lens by using a flat-bladed

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

Front

76MH0A139

Luggage compartment (if equipped)

78RB07039

INSPECTION AND MAINTENANCE -> Bulb replacement for Your Suzuki Jimny SUV Fourth Generation (2018-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals