2018-2026 Suzuki Jimny SUV INSPECTION AND MAINTENANCE -> Tyres User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

INSPECTION AND MAINTENANCE -> Tyres for Your Suzuki Jimny SUV Fourth Generation (2018-2026)

Brake discs and brake drums
Brake disc
Brake location
Minimum thickness
Front wheels
8.0 mm (0.3 in.)
Brake drum
Brake location
Maximum inner
diameter
Rear wheels
222 mm
(8.74 in.)
If the measured thickness or inner diame-
ter of the most worn part falls below or
exceeds the value indicated above, the
parts should be replaced with a new one.
The measurement involves disassembling
each brake and requires the use of a
micrometer or caliper, which must be done
according to the instructions described in
the relevant service manual or available
from the relevant repair information site.
Steering wheel
78RB07012
Steering wheel play
11
c":
0- 30 mm (0.0 -1.2 in.)
Check the free play of the steering wheel
by gently turning it from left to right and
measuring the distance that it moves
before you feel slight resistance. The play
should be between the specified values.
Check that the steering wheel turns easily
and smoothly without rattling by turning it
all the way to the right and to the left while
driving very slowly in an open area. If the
amount of free play is not as specified or
you find anything else to be wrong, an
inspection must be performed by a
SUZUKI dealer.
INSPECTION AND MAINTENANCE
Tyres
78RB07013
The front and rear tyre pressure specifica-
tions are listed in the tyre information label.
Both front and rear tyres should have the
specified tyre pressure.
NOTE:
The tyre pressure will change due to
changes in atmospheric pressure, tem-
perature or tyre temperature when driving.
To reduce the chance that the low tyre
pressure warning light (if equipped) will
come on due to normal changes in tem-
perature and atmospheric pressure, it is
important to check and adjust the tyre
pressures when the tyres are cold. If you
check tyres after driving, they are warm.
Even if the tyre pressure seems to be good
in this condition, it could fall below the
6-36
INSPECTION AND MAINTENANCE
specified pressure when tyres cool down.
Also, tyres that are inflated to the specified
pressure in a warm garage may have pres-
sure below the specification when the vehi-
cle is driven outside in very cold
temperature. If you adjust the tyre pres-
sure in a garage that is warmer than the
outside temperature, you should add 1 kPa
to the recommended cold tyre pressure for
every O.B'C difference between garage
temperature and outside temperature.
6-37
Tyre inspection
Inspect your vehicle's tyres at least once a
month or before long trip by performing the
following checks:
1) Measure the air pressure with a tyre
gauge. Adjust the pressure if neces-
sary. Remember to check the spare
tyre, too.
A WARNING
• Air pressures should be checked
when the tyres are cold or you may
get inaccurate readings.
Check the inflation pressure from
time to time while inflating the tyre
gradually, until the specified pres-
sure is obtained.
Never under-inflate or over-inflate
the tyres.
Under-inflation can cause unusual
handling characteristics or can
cause the rim to slip on the tyre
bead, resulting in an accident or
damage to the tyre or rim.
Over-inflation can cause the lyre to
burst, resulting in personal injury.
Over-inflation can also cause
unusual handling characteristics
which may result in an accident.
(1)
(2)
78RB07048
(1) Tread wear indicator
(2) Indicator location mark
2) Check that the depth of the tread
groove is more than 1.6 mm (0.06 in.).
To help you check this, the tyres have
molded-in tread wear indicators in the
grooves. When the indicators appear
on the tread surface, the remaining
depth of the tread is 1.6 mm (0.06 in.)
or less and the tyre should be replaced.
3) Check for abnormal wear, cracks and
damage. Any tyres with cracks or other
damage should be replaced. If any
tyres show abnormal wear, have them
inspected by a SUZUKI dealer.
A CAUTION
Hitting curbs and running over rocks
can damage tyres and affect wheel
alignment. Have tyres and wheel
alignment checked periodically by a
SUZUKI dealer.
4) Check for loose wheel nuts.
5) Check that there are no nails, stones or
other objects sticking into the tyres.
A WARNING
• Your SUZUKI vehicle is equipped
with tyres which are all the same
type and size. This is important to
ensure proper steering and han-
dling of the vehicle. Never mix
tyres of different size or type on the
four wheels of your vehicle. The
size and type of tyres used should
be only those approved by SUZUKI
as standard or optional equipment
for your vehicle.
Replacing the wheels and tyres
equipped on your vehicle with cer-
tain combinations of aftermarket
wheels and tyres can significantly
change the steering and handling
characteristics of your vehicle.
Therefore, use only those wheel
and tyre combinations approved by
SUZUKI as standard or optional
equipment for your vehicle.
NOTICE
Replacing the original tyres with
tyres of a different size may result
in false speedometer or odometer
readings. Check with a SUZUKI
dealer before purchasing replace-
ment tyres that differ in size from
the original tyres.
Replacing a tyre with one of a dif-
ferent size, or using different
brands among the four tyres can
result in damage to the drive train.
INSPECTION AND MAINTENANCE
Tyre rotation
5-tyre rotation
L A
65D445
L: Left hand drive
R: Right hand drive
NOTE:
If your vehicle is equipped with the tyre
pressure monitoring system, the spare tyre
TPMS sensor must be recognized when
you include the spare tyre during a tyre
rotation. For details, refer to "Replacing
Tyres and/or Wheels" in "Tyre Pressure
Monitoring System (TPMS)" in the "OPER-
ATING YOUR VEHICLE" section.
6-38
AND MAINTENANCE
4-tyre rotation
65D459
To avoid uneven wear of your tyres and to
prolong their life, rotate the tyres as illus-
trated. Tyres should be rotated every
10000 km (6000 miles). After rotation,
adjust front and rear tyre pressures to the
specification listed on your vehicle's Tyre
Information Label.
6-39
Changing Wheels
78RB07014
To change a wheel, use the following pro-
cedure:
1) Remove the jack, tools and spare
wheel from the vehicle.
NOTE:
How to remove the spare wheel:
78RB07052
1. Remove the center nut (1 ), then
remove the spare wheel half cover
(2) (if equipped).
2. Remove the wheel nuts of the spare
wheel, then remove the spare wheel
with both hands.
2) Loosen, but do not remove the wheel
nuts.
3) Jack up the vehicle (follow the jacking
instructions in the "EMERGENCY SER-
VICE" section in this manual)
4) Remove the wheel nuts and wheel.
5) Before installing the new wheel, clean
any mud or dirt off from the surface of
the wheel and hub with a clean cloth.
Clean the hub carefully; it may be hot
from driving.
6) Install the new wheel and replace the
wheel nuts with their cone shaped end
facing the wheel. Tighten each nut
snugly by hand until the wheel is
securely seated on the hub.
78RB07017
Tightening torque for wheel nut:
100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts
in a crisscross fashion with a wrench as
shown in the illustration.
A WARNING
Use genuine wheel nuts and tighten
them to the specified torque as soon
as possible after changing wheels.
Incorrect wheel nuts or improperly
tightened wheel nuts may come
loose or fall off, which can result in
an accident. If you do not have a
torque wrench, have the wheel nut
torque checked by a SUZUKI dealer.
INSPECTION AND MAINTENANCE
NOTE:
How to install the spare wheel:
(3)
78RB07053
When you install a 195/B0R 15 spare wheel to
the vehicle, set the spare tyre bracket (3) (if
equipped) with the mark of "195" on up posi-
tion, and handle it in the reverse order of
removal. For vehicles equipped with the
spare wheel half cover; when you install the
spare wheel half cover, check that the hollow
(4) of the cover is positioned below the center
of the spare wheel half cover.
6-40

Related Topics

Popular Owner Manuals