Get Ease of use and comfort -> Cruise control Guide for Citroen Relay Van 2014-2024

Steering mounted controls

travelling abroad

If using your vehicle in a country

that drives on the other side of the road,

the headlamps must be adjusted to avoid

dazzling on-coming drivers.

Contact a CITROËN dealer or a qualified

workshop.

PArKInG LAMPS

HEAdLAMP BEAM

This system enables you to leave the lamps

on when parked; with the ignition off, key in

the STOP position or key removed.

You are advised to adjust the height of the

headlamp beams in accordance with the

load in your vehicle.

Move the ring on the lighting stalk to position This function works in the dipped and main

O then to dipped or main beam headlamps.

beam headlamps position.

Press these controls, located

the indicator lamp in the

on the dashboard, several times

in succession to adjust the

headlamps.

instrument panel comes on.

The lamps will remain on while

you are parked.

An indicator in the screen shows

the adjustment position selected

(0, 1, 2, 3).

Leaving the lighting on for long periods may

significantly reduce the state of charge of

your vehicle's battery.

Steering mounted controls

When washing the vehicle, switch off the

ignition or deactivate the automatic rain

sensitive wipers.

Good practice

Check that the windscreen wiper blades can

operate freely when using the wipers in icy

weather.

Use the step in the front bumper, to remove

any accumulation of snow at the base of the

windscreen and on the blades.

Slow continuous wiping: 2 notches downwards.

WIPEr cOntrOL StALK

Windscreen wipers

You can change the wiper blades.

Fast continuous wiping: 3 notches

downwards.

Refer to the "Quick help - Worn wiper

blade" section.

Wiping is only active when the ignition key is

in the runnInG position.

Single wipe: pull the control stalk towards

the steering wheel.

With Stop & Start, when the wiper

control stalk is in the fast wipe position,

the STOP mode is not available.

The control stalk has five different positions:

Automatic rain sensitive windscreen

wipers

Wipers off.

If your vehicle is fitted with this system, the

wiping speed is adapted automatically to the

intensity of the rainfall.

Screenwash and headlamp wash

Intermittent wiping: 1 notch downwards.

Pull the wiper control stalk towards you,

the screenwash is accompanied by a timed

operation of the wipers.

In this position, four wiping frequencies

can be selected by turning the ring:

Automatic wiping: 1 notch downwards. This is

conﬁrmed by one wipe. Must be reactivated

each time the ignition is switched on.

Depending on version, the headlamp wash is

coupled with the screenwash, it is triggered if

the dipped beam headlamps are on.

- very slow frequency

- slow frequency

In this position, the sensitivity of the rain

sensor can be increased by turning the ring.

- standard frequency,

- fast frequency.

You can check the fluid level.

Do not cover the rain sensor, located at

the top centre of the windscreen.

Refer to the "Checks - Levels and

checks" section.

3

Steering mounted controls

cruISE cOntrOL

(3 LItrE HdI EnGInE)

"This is the speed at which the driver wishes to

travel".

This aid to driving in free-ﬂowing trafﬁc conditions

enables the vehicle to maintain a constant

speed programmed by the driver, except when a

considerable load is carried on a steep gradient.

In order to be programmed or activated,

the vehicle speed must be greater than

approximately 18 mph (30 km/h), with 2nd gear

or higher engaged.

If your vehicle is fitted with cruise control,

this is displayed on the instrument panel by

an indicator located in the rev counter.

Function selected.

Function deactivated.

Steering mounted controls

temporarily exceeding the

programmed speed

When the cruise control is active, it is still

possible to exceed the programmed speed

by depressing the accelerator pedal (to

overtake another vehicle for example).

Selecting the function - On

Switching off / deactivating the function

Selecting On switches the function on. A

message appears in the instrument panel

screen to confirm the action.

Press the brake or clutch pedal or place

the ring in the OFF position, the indicator

goes off.

changing the programmed speed

while the cruise control is in operation

You can:

If the dynamic stability control system comes

into operation, the cruise control system is

deactivated temporarily.

-

increase the speed in steps, by means of

brief presses, or continuously by pressing

and holding the control upwards (+ sign),

Programming a speed

Accelerate to the required speed, with 2nd

to 6th gear engaged.

restore - rES

Move the control upwards (+), for

approximately one second, to store this

speed.

To restore the vehicle's

programmed speed (for example

after pressing the brake or clutch

pedal), gradually return to the chosen speed

and press rES.

Release the pressure on the accelerator

pedal, the vehicle will maintain this speed.

-

decrease the speed continuously

by pressing and holding the control

downwards (- sign).

The indicator lamp comes on, the cruise

control function is restored.

3

Steering mounted controls

cancelling the programmed speed

Good practice

When the vehicle stops, after the ignition is

switched off, the system no longer stores

any speed.

When changing the programmed reference

speed by pressing and holding the control,

take care as the speed may increase or

decrease rapidly.

Do not use the cruise control on slippery

roads or in heavy traffic.

Operating fault

On a steep gradient, the cruise control will

not be able to prevent the vehicle from

exceeding the programmed speed.

In the event of a fault, the system

is switched off and the indicator

goes off.

The cruise control cannot, in any

circumstances, replace the need to comply

with speed limits or vigilance on the part of

driver.

Contact a CITROËN dealer or a qualified

workshop to have the system checked.

It is advisable to leave your feet near the

pedals.

To prevent the mat from becoming caught

under the pedals:

-

ensure that the mat is positioned

correctly,

-

never fit one mat on top of another.

Steering mounted controls

The status of the cruise control is given

by an indicator in the rev counter and

messages in the instrument panel screen.

Function selected.

Function deactivated.

cruISE cOntrOL

Selecting the function

"This is the speed at which the driver wishes

to drive".

In order for it to be programmed or

activated, the vehicle speed must be greater

than 18 mph (30 km/h) with 2^ndgear or

higher engaged.

-

Turn the ring fully upwards. The cruise

control is selected but is not yet active

and no speed has been programmed.

The indicator comes on in the instrument

panel

This aid to driving in free-flowing traffic

enables the vehicle to maintain the speed

programmed by the driver, unless a

steep gradient or heavy load makes this

impossible.

3

Ease of use and comfort -> Cruise control for Your Citroen Relay Van 2014-2024

Related Topics

Ease of use and comfort

Popular Owner Manuals

Latest Owner Manuals