Get Ease of use and comfort -> Programmable additional heating Guide for Citroen Relay Van 2014-2024

Ventilation

AddItIOnAL HEAtInG SYStEMS

Additional heating

This is passenger compartment heating,

additional to the standard equipment.

It can operate independently of the engine.

Additional heater or programmable

additional heating

This is an additional, programmable and

separate system which heats the Diesel

engine hot coolant loop to make starting

easier.

Supplementary heating

rEAr HEAtInG And / Or AIr

cOndItIOnInG

It improves the demisting and defrosting

performance and that of the heated seats, if

fitted to the vehicle.

On the 2-3 seats version, this is located

under the seat on the driver's side with air

diffusion directed forwards.

If your vehicle is fitted with an additional

air conditioning unit, located in the rear of

the vehicle: the distribution rail located in

the roof and the individual diffusion vents

provide a perfect diffusion of cold air.

The passenger compartment heating is

brought up to temperature more rapidly.

On the 5-9 seats version, it is

located at the rear. Depending

on the model version, the air

This system must be programmed to start up

before you enter the vehicle.

The warm air diffused at the floor, from the

front air conditioning unit, is distributed at

the feet of the rear passengers of rows 2

and 3.

diffusion is either direct from the

rear or comes from the rail located under

each of the two rows of seats.

Automatic additional heating

This is an additional system which starts

automatically when the ignition is switched

on. Its activation depends on the ambient

temperature and the temperature inside the

vehicle.

A warm air diffusion vent, located on the rear

left wheelarch, may complete the assembly

for the feet of the rear passengers of row 3.

Press this control to activate/

deactivate the heating. The LED

is on if the heating is activated.

When rapid demisting and

defrosting is required, switch off the control.

It switches off automatically once the

heating system is started manually.

Ventilation

To deactivate the fan, place the control in

position 0.

However, a safety device will ventilate the

rear circuit automatically, even if the control

is in position 0, to prevent the formation of

condensation.

Activation/deactivation

This control, located on the

MOdE control panel, enables

you to activate/deactivate the

operation of the rear controls

comfort value adjustment

from the driver's seat.

Control positioned:

The first press activates (LED on).

-

on the blue, delivers cool air,

A second press deactivates (LED off).

Air flow

-

on the red, delivers heating

of the ambient air.

The force of the fan blown air,

via the vents, varies from 1 to the

strongest 4.

To obtain a comfortable level of

ambient air, remember to adjust

this control.

The OFF control on the "Mono-zone" central

control panel switches the function off.

3

Ventilation

Time display

Setting the time of the internal clock

Set the clock on the control panel before

programming the deferred switching on of

the heating.

Heating cycle indicator

Time setting and reading indicator

Press and hold the "set" button.

The time setting screen and

indicator come on.

Within ten seconds, press one of the two

setting buttons until the correct time is

displayed:

Display of the programme number

PrOGrAMMABLE AddItIOnAL

selected

HEAtInG

-

">" to increase the time,

"<" reduce the time.

If your vehicle is fitted with separate

programmable heating, it gradually brings

the engine up to a good temperature to

facilitate starting.

or

-

Ventilation indicator

Press and hold the button for more rapid

scrolling of the digits.

An integrated clock permits programming of

its start time. The passenger compartment

will be heated more quickly.

Time setting buttons

Release the "set" button.

When the screen is off, the time is

memorised.

Programme selection button

digital programming control

reading the time

The programmable heating control panel

is located to the side of the steering wheel

below the MOdE switch panel.

Press the "<" or ">" button.

Button for immediate switching on

of the heating

This time reading indicator comes

on and the time is displayed for

approximately ten seconds.

Ventilation

The "- -:- -" symbol or the

Immediate heating

cancelling the programming

previous stored time and the

number (1, 2 or 3) corresponding

to the recalled pre-selection are

Before switching on the heating, check that:

Press the "set" button briefly to

clear the programmed start time.

-

the temperature setting control is in the

"Hot air" position (red),

The screen illumination and the

pre-selection number (1, 2 or 3)

go off.

displayed for ten seconds.

-

the air flow setting control is in

note: if you wish to recall the other pre-

selected times, press the "set" button

repeatedly before the ten seconds have

elapsed.

position "2".

Press this button.

The screen and the heating cycle

indicator come on and remain

on throughout the duration of

operation.

Within ten seconds, press the "<"

or ">" setting button to select the

required start time.

recalling one of the pre-selected

start times

Press the "set" button as many

times as necessary until the

number corresponding to the

required pre-selected start time

(1, 2 or 3) appears.

Setting of the stored time is confirmed by

clearing of the start time, displaying of

the pre-selection number (1, 2 or 3) and

illumination of the screen.

deferred heating

Switching on can be programmed between

one minute and twenty-four hours in

advance.

After ten seconds, the time disappears but

remains stored while the corresponding

number (1, 2 or 3) and the screen

remain on.

You can store up to three different start

times, but programme one deferred start

only.

By default, pre-selected times are

already memorised in the system

(1 = 6 hours; 2 = 16 hours; 3 = 22 hours).

Any modification cancels and replaces the

previous pre-selected time.

note: if you wish to start the heating at a

fixed time each day, simply reprogramme

the stored time each day.

If the battery is disconnected, the default

pre-selected times are restored.

Press the "set" button, the

screen comes on.

3

Ease of use and comfort -> Programmable additional heating for Your Citroen Relay Van 2014-2024

Related Topics

Ease of use and comfort

Popular Owner Manuals

Latest Owner Manuals