2024-2026 Cupra Terramar SUV Assistant systems User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Assistant systems for Your Cupra Terramar SUV First Generation (2024-2026)

194
Assistant systems
Assistant systems
General notes
Safety advice
WARNING
●
Responsibility for driving rests with the
driver at all times. The drive assist systems
are not a replacement for driver attention.
Focus all your attention on driving and be
prepared to intervene at all times.
●
Use the drive assist systems only when con-
ditions allow. The driving style must always
be suitable for the weather, visibility, road
and traic conditions.
●
In order for drive assist systems to react
correctly, sensors and cameras must operate
without limitations. Please read the notes on
sensors and cameras in this chapter.
Note
●
Keep in mind the specic rules of each
country, especially when it comes to driving,
formation of an emergency corridor, braking
distance, speed, parking position, wheel po-
sition, etc. The driver is solely responsible
for always complying with the specic regu-
lations of each country.
●
The area in front of and around the radar
sensor should not be covered with adhesives,
additional headlights or similar items, as this
could have a negative impact on the oper-
ation of the assistants. If the vehicle is not
properly repaired or structural modications
are made to it, the operation of the assistants
may be aected.
●
The repair and adjustment of sensors and
cameras requires special knowledge and
tools. This is why CUPRA recommends visit-
ing a specialised CUPRA dealer or any SEAT
network dealer.
System limits
WARNING
●
Drive assist systems can not overcome the
laws of physics. Depending on the circum-
stances, a collision may not be avoidable.
●
Warnings, notices and control lamps may
not be displayed on time, or may be displayed
incorrectly, e.g. if a vehicle approaches too
quickly.
●
Corrective interventions by drive assist sys-
tems (e.g. interventions in the steering or
brakes) may be insuicient or may never oc-
cur, depending on the circumstances. As a
driver, you must be prepared to act at all
times.
Note
●
Due to the system's detection limits in
the surroundings, the systems may not give
warnings or intervene on time, or they might
do so even if it is not desired. In addition, the
auxiliary systems may incorrectly interpret a
manoeuvre and, as a result, warn the driver in
an unexpected manner.
●
When the towing mode is selected, some
assist systems may react with limitations, in
an unusual way or may not be available. Keep
in mind the instructions relating to the tow-
ing mode.
Button for the assistant systems
Fig.123 Left side of the multifunction
steering wheel: button for driver assistance
systems (depending on the version).
Assistant systems
195
Drive assist sensors and cameras
The button for the driver assistance systems is
located on the multifunction steering wheel.
This button can be used to switch the driver
assistance systems in the Assistants menu on
and o.
●
Press the button to open the Assistants
menu.
●
Select the assistance system in question and
turn it o or on. A mark indicates that assistant
system is switched on.
●
Next, conrm the selection by pressing
the button on the multifunction steering
wheel.
The assistant systems can also be switched on
and o in the infotainment system, in the vehi-
cle settings menu ›››page39.
Drive assist sensors and
cameras
Front radar
Fig.124 On the front bumper: front and
side radar sensors.
Fig.125 Detection area.
The vehicle may be tted with radar sensors on
the front bumper ›››
Fig.124.
The front radar detects any objects in its de-
tection zone ›››
Fig.125 and provides support
for the following functions:
●
Front Assist ›››page211.
●
Adaptive Cruise Control (ACC) ›››page204.
The radar can have a range of up to 120m
(400ft) depending on road and weather con-
ditions.
Side radars ›››Fig.124 detect objects in their
detection zone in order to prevent the vehicle
from colliding with crossing vehicles when en-
tering an intersection or junction. These radars
provide support to the:
●
Junction assist function ›››page213.
Automatic deactivation of supported func-
tions
The front sensors deactivate automatically
when, among other reasons, it is detected that
they are permanently covered. This may be the
case if, for example, there is a layer of snow or
ice on top of the sensor.
If the sensor is deactivated, the instrument
cluster will temporarily display the message
“Driver assist now limited. Front sensors
without visibility” accompanied by an audible
signal.
Due to the front sensor systems not being able
to see, each of the ACC and Front Assist func-
tions will be shown as permanently disabled.
196
Assistant systems
WARNING
●
The visibility of the radar sensors can be
impaired by dirt or environmental inuences,
such as rain, fog, snow, mud, dust, insects,
etc.
●
Clean the sensor area on the bumper as
indicated in ›››page395, Cleaning the
exterior. When the radar sensor starts cor-
rectly detecting again, the message disap-
pears from the screen and the functions be-
come available again.
NOTICE
●
If the radar sensors are dirty or poorly ad-
justed, the Front Assist or Junction assist sys-
tem may give unnecessary warnings and ap-
ply the brakes inappropriately.
●
The operation of the radar sensors can be
aected by strong reections of the emitted
signal. This may occur, for example, in an
enclosed car park or due to the presence
of metallic objects (e.g. guard rails or sheets
used in road works).
●
The sensor may not be adjusted correctly if
it receives an impact. This may compromise
the system's eicacy or disconnect it. If you
have the feeling that the radar sensor is dam-
aged or adjusted incorrectly, switch o the
Front Assist, ACC and Junction assist func-
tions to avoid any damage. If this occurs have
it adjusted.
●
The rear bumper should only be painted
with paint authorised by CUPRA. Junction as-
sist functions may be limited or work incor-
rectly if other paints are used.
Interior camera
Depending on the equipment, the vehicle may
be tted with a camera on the interior rear
view mirror. This camera detects the driver and
his/her driving behaviour to provide support to
the:
●
driver attention monitoring function
›››page29.
NOTICE
Take the following points into consideration
to ensure the camera’s functionality is not
aected:
●
Do not cover the eld of vision of the cam-
era.
●
Adjust the mirror correctly.
Front camera
Fig.126 On the windscreen: eld of vision
of the Lane Assist system camera.
Depending on the equipment, the vehicle may
be tted with a front camera on the front
windscreen. This camera detects lane bounda-
ries (lines) to provide support for the following
functions:
●
Lane Assist ›››page215.
●
Travel Assist ›››page218.
●
Emergency assist ›››page221.
Automatic deactivation of supported func-
tions
The front camera automatically switches o
when, among other things, it detects that it is
permanently covered. This may be the case if,
for example, there is a layer of snow or ice.
Assistant systems
197
Drive assist sensors and cameras
If the camera is deactivated, the instrument
cluster will temporarily display the message
“Driver assist now limited. Front sensors
without visibility” accompanied by an audible
signal.
Due to the front sensor systems not being able
to see, each of the Lane Assist, Travel Assist
and Road Sign Recognition functions will be
shown as permanently disabled.
NOTICE
To avoid aecting the operation of the sys-
tems, take the following points into consider-
ation:
●
Clean the eld of vision of the camera reg-
ularly and make sure it is free of snow and ice.
●
Do not cover the eld of vision of the cam-
era.
●
Check that the windscreen is not damaged
in the area of the camera's eld of vision.
Rear radar
Fig.127 Rear view of the vehicle: radar
sensor areas.
Fig.128 Sensor detection zones.
The rear radar sensors are located on the left
and right of the bumper and are not visible
from the outside ›››
Fig.127. The sensors
monitor both the blind spot and traic behind
the vehicle ›››Fig.128.
They support the following functions:
●
Side Assist ›››page222.
●
Rear Cross Traic Alert ›››page256.
●
Exit Warning ›››page257.
Automatic deactivation of supported func-
tions
The rear radar sensors deactivate automati-
cally when, among other reasons, one of the
sensors is detected to be permanently cov-
ered. This may be the case if, for example,
there is a layer of snow or ice in front of one
of the sensors.
The relevant text message will appear in the
instrument cluster display.
Control lamps
Side Assist function not available
Rear Cross Traic Alert function not avail-
able.
Exit Warning not available.
198
Assistant systems
NOTICE
●
The radar sensors on the rear bumper may
be damaged or shifted in the event of a colli-
sion, for example, when entering or exiting a
parking space. This may result in the system
disconnecting itself, or at least potential di-
minished functionality.
●
In order to ensure that the radar sensors
work properly, keep the rear bumper free of
snow and ice and do not cover it.
●
The rear bumper should only be painted
with paint authorised by CUPRA. The lane
departure warning's functions may be limited
or work incorrectly if other paints are used.
●
The visibility of radar sensors may be aec-
ted due to leaves, snow, dense haze or dirt,
among others. Clean the area in front of the
sensors.
●
Never use auto lane changing or the rear
cross traic alert if the radar sensors are
dirty.
●
Radar operation may also be aected if ob-
jects such as bicycle racks or luggage racks
interfere with the visibility of the radars.
Ultrasound sensors
The bumpers are tted with ultrasound sen-
sors to perform the following functions:
●
Park Assist ›››page235.
●
Park assist plus ›››page231.
●
Rear park assist ›››page234.
NOTICE
●
Damage to the radiator grille, bumper,
wheel arch and vehicle underbody can mod-
ify the orientation of the sensors. This can af-
fect the parking aid function. Have the func-
tion checked by a specialised workshop.
●
A number plate or number plate holder
with dimensions that exceed the space for
the number plate, or a curved or deformed
number plate can cause false detections or a
loss of sensor visibility.
Note
●
In order to guarantee good operation, keep
the sensors clean, free of snow and ice, and
do not cover them with stickers or other ob-
jects.
●
If you use high-pressure or steam equip-
ment for cleaning, do not apply it directly,
unless you do so very briey, and always keep
a distance of more than 10 cm away.
●
Fitting certain accessories to the front of
the vehicle, such as a plate holder with ad-
vertising, may interfere with the operation of
the Park Assist.
Area View system
Fig.129 On the rear lid handle: location of
the rear assist camera.
Depending on your vehicle’s equipment, it can
be tted with 1 or 4 cameras that provide sup-
port to the following functions:
●
Top View Camera ›››page251.
●
Rear View Camera ›››page248.
WARNING
Fitting a number plate frame may interfere
with the view shown on the screen, as it may
reduce the camera’s eld of vision.
Assistant systems
199
Cruise control system
NOTICE
●
In order to guarantee good system opera-
tion, keep the cameras clean, free of snow or
ice, and do not cover them with stickers or
other objects. The camera can be cleaned by
operating the wiper.
●
Never use abrasive cleaning products to
clean the camera lens.
●
Do not use hot or warm water to remove ice
or snow from the camera lens. Doing so could
damage the camera.
Cruise control system
Introduction
The cruise control system (GRA) helps main-
tain a constant speed set by you.
Speed range
The cruise control system is available when
driving in forward gear at a speed of over ap-
prox. 20km/h (15mph).
Temporarily switching o the cruise control
The saved speed can be exceeded at any
time, e.g. for overtaking. The cruise control is
suspended during acceleration and is then re-
sumed with the saved speed.
Status display
When the cruise control system is switched on,
the instrument cluster display shows the saved
speed and the system status:
Lights up grey.
The cruise control system is switched
on, but regulation is not active.
It lights up green.
The cruise control system is switched on
and regulation is active.
If there is no speed saved, the instrument clus-
ter display shows ––– instead of speed.
Driving down slopes
Shift into a low gear before descending a long
hill. This makes use of engine braking and re-
lieves the brakes.
The vehicle cannot maintain the saved speed
in all driving situations. Always be ready to ap-
ply the vehicle’s brakes.
WARNING
If it is impossible to drive with suicient brak-
ing distance and at a constant speed, using
the cruise control system may cause acci-
dents and serious injuries may occur.
●
Do not use Travel Assist when visibility is
bad, on steep roads, on windy roads or in slip-
pery circumstances (such as snow, ice, rain or
loose gravel), or on ooded roads.
●
Only use the cruise control system on
paved roads with a rm surface.
●
Adapt your speed and safety distance to
the vehicle in front of you at all times to suit
the visibility, weather, road and traic condi-
tions.
●
After use, always switch o the speed lim-
iter to prevent the speed being regulated
against your wishes.
●
It is dangerous to use a set speed which
is too high for the prevailing road, traic or
weather conditions.
Operating the cruise control
Fig.130 On the multifunction steering
wheel: cruise control operation buttons.
Connecting
●
Press the button.
Then select “Cruise control” from the driving
assistants menu.
200
Assistant systems
Regulation has not yet taken place.
Start regulation
●
While driving, press the button .
The cruise control system saves and regulates
the current speed.
Adjusting the speed
While the GRA is set, the stored speed can be
adjusted:
+ 1 km/h (1mph)
- 1 km/h (1mph)
+ 10 km/h (5mph)
- 10 km/h (5mph)
Interrupting the adjustment
●
Briey press the button or press the brake
pedal.
The speed is stored.
Reinstating the cruise control
●
Press the button.
The cruise control system resumes the saved
speed and regulates it.
Troubleshooting
Fault in the speed regulator
The control lamp switches on yellow.
Abnormal operation. Switch o the cruise con-
trol system and take the vehicle to a specialist
workshop.
The adjustment is interrupted unexpectedly
●
The vehicle has exceeded the saved speed
for a long time.
●
No forward gear has been selected.
●
A brake assistance system, e.g. TCS or ESC,
has intervened.
●
Front Assist has braked the vehicle.
●
If the fault continues, disconnect the Emer-
gency Assist and consult a specialised work-
shop.
Speed limiter
Introduction
The speed limiter helps the driver not to ex-
ceed a set speed.
Speed range
The speed limiter helps avoid exceeding a pro-
grammed speed, from 30km/h (20mph) ap-
prox. and faster.
Selecting the speed limiter
The speed limit can be interrupted at any time
by depressing the accelerator pedal fully, be-
yond the point of resistance. As soon as the
saved speed is exceeded, the green indicator
light ashes and an audible warning signal may
sound. The speed is stored.
The limiter is reactivated automatically after re-
turning to less than the set speed.
Status display
When the speed limiter is switched on, the
instrument cluster display shows the saved
speed and the system status:
Lights up grey
The speed limiter is switched on but reg-
ulation is not active.
Lights up green
The speed limiter is switched on and ac-
tive.
Driving down slopes
Shift into a low gear before descending a long
hill. This makes use of engine braking and re-
lieves the brakes.
The vehicle cannot maintain the saved speed
in all driving situations. Always be ready to ap-
ply the vehicle’s brakes.
Assistant systems
201
Speed limiter with proactive speed adjustment
WARNING
After use, always switch o the speed limiter
to prevent the speed being regulated against
your wishes.
●
The speed limiter does not relieve the
driver of their responsibility to drive at the
appropriate speed. Do not drive at high
speed if not necessary.
●
Using the speed limiter under adverse
weather conditions is dangerous and can
cause serious accidents, e.g. aquaplaning,
snow, ice, leaves, etc. Only use the speed
limiter when the status of the road and the
weather conditions allow it.
Operating the speed limiter
Fig.131 On the multifunction steering
wheel: buttons to control the speed limiter.
Connecting
●
Press the button.
Then select “Speed limiter” from the driving
assistants menu.
Regulation has not yet taken place.
Start regulation
●
While driving, press the button .
The current speed is saved as a limit speed.
Adjusting the speed
The programmed speed can be set:
+ 1 km/h (1mph)
- 1 km/h (1mph)
+ 10 km/h (5mph)
- 10 km/h (5mph)
Interrupting the adjustment
●
Press the button.
The speed is stored.
Reinstating the cruise control
●
Press the button.
The limiter will re-activate as soon as the vehi-
cle is moving at a speed lower than the saved
one.
Troubleshooting
The speed limiter is not available
The control lamp lights up in yellow.
●
Malfunctions: Switch o the speed limiter
and go to a specialist workshop.
Regulation is interrupted unexpectedly
●
You have switched o the Electronic Stabili-
zation Control (ESC).
●
The brakes have overheated. Wait for the
brakes to cool down and check the operation
again.
●
If the fault continues, consult a specialised
workshop.
For safety reasons, the speed limiter only
switches o fully whenever the driver stops
pressing the accelerator pedal or switches the
system o manually.
Speed limiter with proac-
tive speed adjustment
Introduction
The speed limiter with proactive speed adjust-
ment automatically adapts a maximum speed
that you have saved to the detected speed lim-
its.
202
Assistant systems
The speed limiter with proactive speed adjust-
ment is an additional function of the speed
limiter and uses the infotainment system’s dy-
namic road sign display ›››page31 and navi-
gation data.
The speed limiter with proactive speed adjust-
ment is available depending on the equipment,
but not in all countries.
WARNING
The smart technology of the speed limiter
with proactive speed adjustment cannot
overcome the limits imposed by the laws of
physics and only works within the limits of
the system. Never allow the greater conven-
ience oered by this function to induce you
to take any risk that compromises safety. Se-
rious accidents and injuries can occur if the
speed limiter with proactive speed adjust-
ment is used carelessly or unintentionally.
The system is not a replacement for driver
awareness.
●
Always adapt your speed to suit visibility,
weather, road and traic conditions.
●
Always pay attention to traic and always
keep the vehicle's surroundings in mind.
●
Always be prepared to adjust the speed
yourself. If the road sign recognition system
is not working properly or the navigation data
is not updated, the speed may change unex-
pectedly and suddenly or may not be suitable
for the current traic situation. In addition,
the speed adjusted by the system may not
suit your driving style.
●
Always be prepared to adjust the speed
yourself. If you drive without any active gui-
ded route, if you leave the route calculated
by the navigation system or if the position of
the vehicle cannot be determined correctly
because the GPS does not provide accurate
data, the speed may change unexpectedly
and suddenly or may not be suitable for the
current traic situation.
●
Always use up to date navigation data.
●
Always take into account the speed limit. In
the case of speed limits that are not included
in the navigation data, the speed limit may be
exceeded.
Note
Please also note the information of relevance
to safety on the speed limiter ›››page200.
Limitations of proactive speed ad-
justment
In addition to the limitations of the dynamic
road sign display system, the speed limiter with
proactive speed adjustment has the following
limitations inherent to the system:
●
The speed limiter with proactive speed ad-
justment only recognises road signs showing a
speed limit.
●
Road signs that indirectly show a speed re-
striction, e.g. signs at the entrance to towns,
are only recognised on the basis of navigation
data.
●
If a warning is given of a speed restriction
based on navigation data, without it being de-
tected by the dynamic road sign display, the
indicated speed will be adjusted to the most
recently saved speed.
●
The speed limiter with proactive speed ad-
justment is not available for speed restrictions
lower than approx. 30 km/h (approx. 20 mph)
that are detected. In this case, a relevant mes-
sage is displayed on the instrument cluster dis-
play.
Activate proactive speed adjust-
ment
The speed limiter with proactive speed adjust-
ment can be activated in the infotainment sys-
tem’s assistants menu.
Driving with proactive speed ad-
justment
●
Activate the proactive speed adjustment.
●
Switch on the speed limiter and start the
control ›››
page200.
Assistant systems
203
Eco Assist
●
When the system recognises a new speed
limit, a warning is displayed on the instrument
cluster. This speed will be stored in the speed
limiter.
The system has recognised a new speed
limit and uses it for regulation.
Interrupting speed adjustment
●
Press the button on the multifunction
steering wheel or release and press the accel-
erator pedal twice. The last saved speed is re-
sumed.
●
Press the button on the multifunction
steering wheel. The current speed is taken.
●
Press the button on the multifunction
steering wheel. The system switches to a pas-
sive state.
Adjust the displayed speed using the buttons
on the multifunction steering wheel
+ 1 km/h (1mph)
- 1 km/h (1mph)
+ 10 km/h (5mph)
- 10 km/h (5mph)
If you adjust the indicated speed excessively,
the proactive speed adjustment is interrupted.
Note
●
When a speed restriction is recognised, the
proactive speed adjustment also adapts the
saved speed, even if the speed limiter is not
active.
●
If the speed of travel considerably exceeds
the speed limit detected by the road signal
detection system, a relevant warning is dis-
played in the instrument cluster display.
●
When merging onto a motorway or dual
carriageway, the recommended speed is au-
tomatically saved as the desired speed.
Troubleshooting
A message is displayed indicating that pro-
active speed adjustment is not currently
available or not oered in your country.
●
If this message is displayed for a longer pe-
riod of time and proactive speed adjustment
is available in your country, please contact a
specialist workshop.
Note
Depending on the anomaly in question, addi-
tional information may be displayed in Vehi-
cle status ›››page41.
Eco Assist
Fig.132 Eco Assist indication (schematic
representation).
Eco-eicient driving assistance helps you drive
with care and with low energy consumption
by following instructions superimposed in the
digital cockpit, depending on the situation.
When you approach places such as a junc-
tion, a roundabout or a section of road with
a speed limit, the symbol
is displayed along
with an event on the digital instrument cluster
›››Fig.132.
As soon as you follow the indication and
take your foot o the accelerator, the vehicle
adapts, based on the selected drive prole and
distance to the event, brake energy recupera-
tion and speed.
204
Assistant systems
Eco Assist uses the trip data from the infotain-
ment system and the sensors of certain driver
assistance systems. If no destination guidance
is active, the most likely route is used.
Pressing the accelerator can cancel the inter-
vention of the assistance at any time.
Eco Assist can be activated and deactivated in
the infotainment system, in the assistance sys-
tem settings ›››page39.
Eco Assist is temporarily deactivated if:
●
The gear selector is in the S position.
●
The Performance or CUPRA drive prole is
used.
●
Driving with adaptive cruise control (ACC) or
cruise control (GRA).
When these conditions no longer exist, the as-
sistance is reactivated if it is switched on in the
assistance system settings.
Eco Assist is available depending on equip-
ment and not in all countries.
WARNING
The system is not a replacement for driver
awareness.
●
Adapt your speed and driving style at all
times to suit visibility, weather, road and traf-
c conditions.
●
Road signs on the road and traic regula-
tions have priority over eco-driving notes.
Note
●
The appearance of the symbols may vary
slightly depending on the equipment and
model. System updates may modify or ex-
pand the symbols.
●
When the system is active, Eco Assist may
also increase recuperation without display-
ing any indication. This can occur in situa-
tions such as when the accelerator pedal is
released when a vehicle is driving in front. In
this case, energy recuperation is adapted to
match the speed of the vehicle in front with-
out any indication being displayed.
ACC - Adaptive Cruise
Control
Introduction
Adaptive Cruise Control (ACC) maintains a
constant speed set by the driver. When ap-
proaching another vehicle in front, the ACC
detects it and adapts the speed automatically,
maintaining a distance set by the driver.
Does my vehicle have ACC?
Your vehicle has ACC if it has the ACC function
buttons on the multifunction steering wheel
›››
page123, or if it has the conguration
menu in the infotainment system.
Speed range
ACC regulates at speeds between 20 and
210km/h (15 and 130mph).
When Electric mode is activated in hybrid ve-
hicles, the ACC speed range may vary.
The ACC can bring the vehicle to a standstill if
a vehicle in front stops.
Driving with ACC
You can override the ACC at any time. Brak-
ing interrupts the ACC. If you accelerate, reg-
ulation is interrupted during acceleration and
then resumed.
Driver intervention prompt
ACC is subject to certain limitations in-
herent to the system. This means that the
driver will have to control the speed and
distance from other vehicles in certain sit-
uations. In this case, the instrument clus-
ter display will tell you to intervene by
applying the brake, and an audio warning
will be played.
Radar sensors
The ACC uses the front radar technology. Read
its maintenance instructions and information
about its limitations ›››
page194.
Assistant systems
205
ACC - Adaptive Cruise Control
1
2
WARNING
The ACC’s technology cannot overcome the
system's inherent limitations or change the
laws of physics. If used negligently or invol-
untarily, it may cause serious accidents and
injuries. The system is not a replacement for
driver awareness.
●
Always be prepared to brake or accelerate.
●
If you press the accelerator pedal the ACC
will stop working. Therefore, it will not brake
or request any braking intervention.
●
Adapt your speed and safe distance to the
vehicle in front of you at all times to suit visi-
bility, weather, road and traic conditions.
●
Do not use the ACC in poor visibility, or on
roads that are steep, with lots of curves or
slippery.
●
Never use ACC when driving o-road or on
unpaved roads.
●
The system may not react in time to
stationary obstacles (such as a traic jam
queue), particularly at high speeds. React
soon enough to avoid a hazardous situation.
●
The system may not react to stopped vehi-
cles in the same lane. You must react early
enough yourself in this case.
●
The system does not react to people, an-
imals or vehicles that are crossing or ap-
proaching in the opposite direction.
●
If you are driving with a spare wheel tted,
the ACC system could automatically switch
o. Switch o the system when starting o.
●
Brake immediately if the ACC does not slow
down enough.
●
Brake immediately when a driver interven-
tion instruction is displayed on the instru-
ment cluster screen.
●
If the vehicle continues to move involun-
tarily after a driver intervention prompt,
brake the vehicle.
●
The brake pedal may move downwards dur-
ing braking. Be careful not to position your
foot under the pedal.
Note
If the ACC does not work as described in
this chapter, do not use it until it has been
checked by a specialised workshop. CUPRA
recommends visiting a specialised CUPRA
dealer or any SEAT dealership.
ACC operation
Fig.133 On the instrument cluster display:
ACC active.
Fig.134 On the multifunction steering
wheel: buttons for operating the ACC.
›››
Fig.133
Vehicle detected in front. It will light up if
the distance to the vehicle is set.
Distance selected.
206
Assistant systems
Connecting
●
Press the button on the multifunction
steering wheel ›››Fig.134.
●
Then select the “ACC (Adaptive Cruise
Control)” checkbox in the driving assistants
menu.
The ACC does not regulate anything yet
(standby).
Start regulation
Activating the ACC system also automatically
activates the ESC and traction control (TCS).
●
To start regulation, press the button
›››Fig.134.
The ACC saves the current speed and main-
tains the set distance. If the current speed
is outside the predened speed range, ACC
adjusts the speed to the nearest limit of the
range.
Depending on the driving situation, the follow-
ing control lamps come on:
Lights up green
ACC connected, no vehicle detected in
front.
Lights up green
ACC connected, vehicle detected in
front.
When the ACC is in standby, the control lamps
light up grey.
Program the speed
+ 1 km/h (1mph)
- 1 km/h (1mph)
+ 10 km/h (5mph)
- 10 km/h (5mph)
Program the distance setting
The distance can be set to one of ve levels,
from very short to very long:
●
Press the button and then or button
›››Fig.134.
●
Alternatively, press button as many times
as necessary to set the desired distance.
Keep in mind each country’s regulations on
minimum braking distances.
Suspend regulation (standby)
●
Briey press button ›››Fig.134 or press
the brake pedal.
The ACC indicator lamp is grey; the speed and
distance are saved.
If the ESC or TCS is switched o, the ACC is
automatically interrupted.
Reinstating the cruise control
●
Press the button. The ACC regulates to
the last speed and distance setting.
●
OR: Press button to regulate to the cur-
rent speed.
Exceeding the speed regulated by the ACC
While driving with the ACC switched on, the
driver can increase speed by pressing the ac-
celerator pedal. ACC regulation is suspended
until you release the accelerator pedal ›››
.
Changing the drive prole
The drive prole selected can aect
ACC acceleration and braking behaviour
›››page185.
WARNING
Before driving o, check that the road is
clear. The radar sensor may not detect ob-
stacles that could be on the road. This can
lead to an accident and serious injury. Press
the brake if necessary.
NOTICE
If you increase speed using the accelerator
pedal, the ACC may not be able to safely
adjust the speed or the distance due to the
limitations of the system.
●
Be prepared to react if required by the sit-
uation.
Assistant systems
207
ACC - Adaptive Cruise Control
1)
Or on the left, in countries that drive on the left hand side of the road.
Special driving situations
Fig.135 On the instrument cluster screen:
ACC active, vehicle detected on the left.
Be aware of the limitations and warnings
described at the beginning of this chapter
›››
page204, Introduction.
Avoid undertaking on the right
1)
If a vehicle is detected in the left lane that is
travelling at a speed slower than that set by
the driver, it will brake the vehicle within the
comfort limits of the system to avoid passing it
on the right ›››
Fig.135.
You can cancel this regulation by changing the
set speed or by pressing the accelerator pedal.
The function works at speeds over 80km/h
(50mph). It may not be available in certain
countries.
Overtaking
When the turn signal is switched on for over-
taking, the ACC reduces the distance from the
vehicle in front to help with the overtaking ma-
noeuvre. The set cruising speed will not be ex-
ceeded.
The function works at speeds over 80km/h
(50mph). It may not be available in certain
countries.
Stop&Go function
The ACC can bring the vehicle to a standstill if
the vehicle in front stops.
The ACC remains active and the message ACC
ready to start is displayed on the instrument
cluster for a few seconds. You can extend or
reactivate this warning by pressing the
but-
ton or by grabbing the wheel if your vehicle is
tted with Travel Assist. During this time, the
vehicle will move o again if the vehicle in front
moves forwards.
To move o when the message ACC ready to
start is not longer displayed, once the vehicle
in front has moved o:
●
Vehicles with automatic transmission:Briey
depress the accelerator pedal.
●
OR: press the button on the multifunc-
tion steering wheel.
●
OR: grab the steering wheel again if your ve-
hicle has Travel Assist.
The ACC does not remain active in the follow-
ing cases:
●
The stopping phase lasts for several minutes.
●
When a vehicle door is opened.
●
If the ignition is switched o.
WARNING
If the message ACC ready to start is displayed
on the instrument cluster display and the
vehicle in front moves o, your vehicle will
move o automatically. In this case, any ob-
stacles in the road may not be detected. This
may cause serious accidents and injuries.
●
Always check the road before moving o,
and apply the vehicle brakes yourself if nec-
essary.
ACC system limitations
The limits of the ACC system mean that it is not
appropriate in all situations ›››
in Introduc-
tion on page205.
CUPRA does not recommend using the func-
tion in the following cases ››› :
●
Heavy rain, snow or fog.
●
When going through tunnels.
●
On stretches of road with roadworks.
●
On routes with curves, e.g. on mountain
roads.
208
Assistant systems
●
On o-road routes.
●
In covered car parks.
●
On roads with embedded metal objects such
as train or tram tracks.
●
On roads with loose gravel.
Pay special attention when using ACC in the
following situations:
On curves
Fig.136 Vehicle on a bend.
The ACC may not detect the vehicle in front
on a curve, or may regulate the distance from
vehicles in other lanes ›››
Fig.136.
Vehicles outside the sensor zone
Fig.137 Motorcyclist ahead out of range of
the radar sensor.
Fig.138 Vehicle changing lanes.
In the following situations the ACC may not
react, or may react slowly or inappropriately:
●
Vehicles that are not aligned while driving or
that are outside the sensor's detection area,
such as motorcycles ›››
Fig.137.
●
Vehicles that move into your lane, a short
distance from your vehicle ›››Fig.138.
●
Vehicles with loads or accessories that pro-
trude from the sides, rear or roof.
Objects that are not detected
Fig.139 A vehicle turning and another
stationary.
The ACC function only detects and reacts to
vehicles moving in the same direction. There-
fore it does not detect:
●
People
●
Animals
●
Vehicles travelling in the opposite direction
or crossing the road.
●
Other stationary obstacles
The ACC may not react to stationary vehicles.
If, for example, a vehicle detected by the ACC
turns or moves over and there is a stationary
vehicle in front of it, the ACC will not react to
the second vehicle ›››Fig.139.
WARNING
Using the ACC in the above situations can
cause serious accidents and injuries, and you
could break the law.
Assistant systems
209
Predictive speed adjustment
Troubleshooting
ACC not available
The indicator lamp lights up yellow:
●
The radar sensor is dirty or adjusted in-
correctly. Take into account the warnings
described at the beginning of this chapter
›››page195
●
There is a fault or a defect. Turn o the vehi-
cle's ignition and turn it on again after a few
minutes.
●
If the problem persists, consult a specialised
workshop.
The ACC does not work as expected
●
Make sure that the conditions are met for the
radar sensor to operate properly ›››page195.
●
If the brakes overheat, regulation stops au-
tomatically. Wait for them to cool down and
check the operation again.
●
Unusual noises during automatic ACC brak-
ing are normal and do not indicate any anoma-
lies.
The following conditions may lead the ACC
not to react:
●
The accelerator or brake is depressed.
●
No gear is engaged or the vehicle is in gear R.
●
The vehicle is reversing.
●
ESC is operating.
●
The driver is not wearing his/her seat belt.
●
The RPM is too high or too low.
●
A vehicle brake light is faulty.
●
A trailer brake light is faulty.
●
The parking brake is applied.
●
Driving on an excessive slope.
Predictive speed adjust-
ment
Introduction
The predictive speed adjustment adapts the
speed to the speed limits detected and to the
road layout (curves, crossings, roundabouts,
etc.).
Predictive speed adjustment is an additional
function of the ACC ›››
page204 and uses
the road signal detection system and the navi-
gation data of the infotainment system.
Predictive speed adjustment is available de-
pending on the equipment, although not in all
countries.
Reaction at the end of a traic jam
Vehicles with Car2X technology (depending on
the equipment and not in all countries) can
interact with other vehicles in their vicinity.
This allows your vehicle to receive information
about the presence of a traic jam ahead and
to reduce speed in time.
Requirements:
●
Car2X activated in the infotainment system.
●
The option to react at the end of traic
jams is activated in the infotainment system
›››page210.
WARNING
The predictive speed adjustment smart tech-
nology cannot overcome the limits imposed
by the laws of physics and it only works within
the limits of the system. Never allow the en-
hanced convenience of this function to in-
duce you to take any risk that compromises
safety. If used negligently or involuntarily,
it may cause serious accidents and injuries.
The system is not a replacement for driver
awareness.
●
Always adapt your speed to suit visibility,
weather, road and traic conditions.
●
Always pay attention to traic and always
keep the vehicle's surroundings in mind.
●
Always be prepared to adjust the speed
yourself. If the road sign recognition system
is not working properly or the navigation data
is not updated, the speed may change unex-
pectedly and suddenly or may not be suitable
for the current traic situation. In addition,
the speed adjusted by the system may not
suit your driving style.
210
Assistant systems
●
Always be prepared to adjust the speed
yourself. If you drive without any active gui-
ded route, if you leave the route calculated
by the navigation system or if the position of
the vehicle cannot be determined correctly
because the GPS does not provide accurate
data, the speed may change unexpectedly
and suddenly or may not be suitable for the
current traic situation.
●
Always use up to date navigation data.
●
Always take into account the speed limit. In
the case of speed limits that are not included
in the navigation data, the speed limit may be
exceeded.
Note
Also note the information related to the ACC
relevant to safety ›››page204.
Limitations of the predictive speed
adjustment
In addition to the limitations of the road sign
detection system and the limitations of the
ACC, predictive speed adjustment has the fol-
lowing limitations inherent to the system:
●
Predictive speed adjustment only recognises
road signals that show a speed limit. The pre-
dictive speed adjustment does not take into
account, above all, the rules on priority of pas-
sage or traic lights.
●
Road signs that indirectly show a speed re-
striction, e.g. signs at the entrance to towns,
are only recognised on the basis of navigation
data.
●
On roads that are not included in the naviga-
tion data, or that are included with low accu-
racy, predictive speed adjustment is not availa-
ble.
●
If a speed limit is notied based on the nav-
igation data without it being detected by the
road signal detection system, the indicated
speed will be adjusted to the speed that was
saved the last time.
●
Predictive speed adjustment is not available
for speed limits below approx. 20 km/h (ap-
prox. 15 mph). In this case, a relevant message
is displayed on the instrument cluster display.
Activating the predictive speed ad-
justment
In the infotainment system, in the assist serv-
ices menu, you can individually adjust the
type of incident the vehicle should react to
›››
page39:
●
Response to road layout.
●
Response at permitted speeds.
●
Reaction to a traic jam.
Driving with predictive speed ad-
justment
●
Connect the ACC ›››page205.
●
Set the distance and speed.
●
Activate the predictive speed adjustment.
As soon as the system recognises a speed limit
or a relevant road layout during the route, a
warning will appear on the instrument cluster
display. This warning will indicate the reason
and the speed to which the vehicle will adjust
due to said limitation.
Indication of turning intention
If the turn signals are activated to indicate the
intention to turn, the predictive cruise control
can reduce the speed at the next available
turn.
The predictive cruise control does not detect
the intention to turn in the following situations:
●
A dashed line is recognised in the direction in
which the turn signal is activated.
●
The turn signals are not activated suiciently
far in advance.
Indication of regulation in progress
Adjustment due to a speed limit.
Adjustment due to the end of a speed
limit.
Assistant systems
211
Emergency brake assistance system (Front Assist)
Adjustment due to a roundabout.
Adjustment due to a junction.
Adjustment due to a road layout.
Regulation due to a traic jam.
In the event of adjustment due to a speed limit,
the detected speed will be saved as the new
desired speed. In the event of adjustment due
to the road layout, the vehicle will accelerate
again after leaving the reason for the adjust-
ment behind and the speed will be adjusted to
the saved speed.
The speeds indicated for curves depend on
the drive prole ›››page185.
Interrupting speed adjustment
●
During the warning, press the button .
●
During the regulation, press the button .
Adjust the announced speed
The announced speed can only be adjusted in
the event of adjustment due to a speed limit.
Multifunction steering wheel
●
Tapping the buttons or will change the
speed by 10km/h (5mph).
If you adjust the indicated speed excessively,
the predictive speed adjustment is interrupted.
Note
●
When a speed limit is recognised, the pre-
dictive speed adjustment also adapts the
saved speed even if the ACC is switched o.
However, it will not regulate.
●
If the speed of travel considerably exceeds
the speed limit detected by the road signal
detection system, a relevant warning is dis-
played in the instrument cluster display.
●
In the event of joining a highway without
a speed limit, the recommended speed is au-
tomatically saved as the desired speed. If a
higher speed has previously been saved for a
motorway without a speed limit, this is used
instead of the recommended speed.
Troubleshooting
A message is displayed indicating that pre-
dictive speed adjustment is not currently
available or not available in your country.
●
If this message is displayed for a long time
and predictive speed adjustment is available in
your country, contact a specialised workshop.
Note
Depending on the anomaly in question, addi-
tional information may be displayed in Vehi-
cle status ›››page41.
Emergency brake assis-
tance system (Front As-
sist)
Introduction
The objective of the system is to prevent head-
on collisions against objects that may be in the
vehicle’s path or minimise the consequences
of such impacts.
Front Assist detects dierent road users, such
as other vehicles, pedestrians, bicycles and
motorcycles, using a camera on the top of
the windscreen and three radar sensors on the
front of the vehicle ›››
page195.
Depending on several factors and how critical
the situation is, the system operates in a stag-
gered manner.
First by informing the driver, and if there is no
or insuicient reaction, then by activating an
autonomous emergency braking or an evasive
manoeuvre as indicated by the conditions that
will be discussed in the following points.
212
Assistant systems
The system can be cancelled if the accelerator
pedal is pressed or the steering wheel is turned
rmly.
Depending on the equipment and the country,
Front Assist also includes the following func-
tions:
●
Pedestrian protection ›››page213
●
Cyclist protection ›››page213
●
Dodge assist ›››page213
●
Turn-o assist ›››page213
●
Junction assist ›››page213
WARNING
●
Front Assist is a driving assistance function
that can never replace the driver’s attention.
●
Front Assist cannot change the laws of
physics or replace the driver in terms of
keeping control of the vehicle and reacting
to a possible emergency situation.
●
Following a Front Assist emergency warn-
ing, pay immediate attention to the situation
and try to avoid the collision where appropri-
ate.
Warning levels and brake assist
Front Assist is active from 5km/h (3mph).
Depending on dierent conditions (vehicle
speed, speed and type of object recognised,
etc.), some of the stages described below are
omitted to optimise the performance of the
system.
Safety distance warning
If the system detects that you are
driving too close to the vehicle in
front, it will warn the driver with
this indication on the instrument cluster
display.
The timing of the warning varies depending
on driver behaviour, vehicle speed and relative
speed between both.
The safety distance warning is active from ap-
prox. 65km/h (40mph).
Advance warning
If the system detects a possible collision
with the vehicle in front, it alerts the
driver by means of an audible warning
and an indication on the instrument clus-
ter display.
The warning moment varies depending on the
traic situation and driver behaviour. At the
same time, the vehicle will prepare for a possi-
ble emergency braking ›››
in Introduction
on page212.
When Front Assist is connected, the indica-
tions of other functions on the screen may be
hidden.
Critical warning
If the driver fails to react to the advance warn-
ing, the system may actively intervene in the
brakes and generate a brief jolt to warn the
driver of the imminent danger of a collision.
Automatic braking
If the driver also fails to react to the critical
warning, the system may initiate independent
emergency braking by progressively increasing
the braking in accordance with the criticality of
the situation.
Driver emergency braking assistance system
If the driver, after the critical warning, starts
braking but the system detects that the brake
is not being applied with suicient force, the
braking intensity will be increased. This brake
assist only occurs if the pedal is pressed rmly.
WARNING
●
The system cannot prevent a collision, al-
though it can signicantly minimise the con-
sequences by reducing the speed and the
force of the impact.
●
If Front Assist applies the brakes, the brake
pedal is “harder”.
●
Automatic interventions by Front Assist
on the brakes may be interrupted by press-
ing the accelerator or moving the steering
wheel.
Assistant systems
213
Emergency brake assistance system (Front Assist)
●
Front Assist may decelerate the vehicle un-
til it stops completely. However, the brake
system does not halt the vehicle perma-
nently. Use the foot brake!
Pedestrian and cyclist recognition
The system recognises pedestrians and cyclists
who travel in the same lane and direction and
pedestrians and cyclists who transversely cross
the vehicle's path.
Pedestrian and cyclist recognition technology
cannot exceed the physically prescribed limits
and works exclusively within the system’s limits.
The responsibility for braking always depends
on the driver.
The pedestrian and cyclist recognition can
cause undesired warnings and braking inter-
ventions, e.g. with a hidden radar sensor or a
dirty camera eld of vision.
Be ready to take charge of the vehicle at any
time.
The pedestrian and cyclist recognition operat-
ing speed range is lower than that of Front As-
sist.
Dodge assist
Dodge assist helps the driver avoid an obstacle
in critical conditions.
Once the Front Assist has activated a critical
warning, if the driver intends to dodge the ob-
ject, the swerve assist will help correct the tra-
jectory. The driver must start and nish the
manoeuvre, as this is an assistance system and
not an autonomous one.
The system is active between approximately
30km/h (20mph) and 150km/h (90mph).
Limitations
This system does not react to objects crossing
the path of the vehicle or to animals. The basic
limitations of Front Assist must also be taken
into account›››
page214.
Turn-o assist
Turn-o assist can avoid a collision with a vehi-
cle approaching in the opposite direction, by
braking the vehicle itself when the intention is
to turn.
This system is active up to 20km/h (12mph).
Limitations
The turn-o assist function is available if you
have indicated your intention to turn by acti-
vating the turn signal, you have turned the
steering wheel and the turning path has star-
ted.
It only reacts to vehicles that are in the path of
the vehicle (not to animals, people, etc.).
The basic limitations of Front Assist must also
be taken into account›››
page214.
Junction assist
Junction Assist can prevent the vehicle from
colliding with a vehicle crossing the road as it
enters an intersection or junction.
If there is a risk of collision when exiting an
exit or entering a junction, Junction Assist can
issue a visual and audible warning and brake
the vehicle. This can reduce the risk of an acci-
dent.
Displays
At low speeds, the park assist display uses
coloured segments to show detected crossing
traic.
Fig.140 In the infotainment system:
junction assist display.
214
Assistant systems
Yellow segment: Junction assistant has
detected crossing traic. Pay attention
and be prepared to brake.
Red segment: Junction assist has detec-
ted a potential collision with crossing traf-
c. Brake!
Depending on the situation, the coloured ar-
rows are also shown on the head-up display or
on the instrument cluster. These indicate the
direction from which cross traic is approach-
ing.
Speed range
Junction assist is available in a speed range
from 0km/h (0mph) to around 65km/h (close
to 40mph).
Limitations
Junction assist does not react to road users
who are hidden by structures or other road
users. Road users leaving a place where they
were concealed may be detected with a delay.
Always keep in mind the basic limitations of the
Front Assist ›››page214 system.
System limitations
Front Assist has certain limitations inherent to
the system. Thus, in certain circumstances,
some of the reactions may be inappropriate
from the driver's standpoint. So pay attention
in order to intervene if necessary.
The following conditions may cause Front
Assist not to react or to do so too late:
The indication will be shown on the in-
strument cluster display in the rst few
instants of driving after switching on the
ignition, due to the system’s initial auto-
calibration.
Unrecognised objects
●
Vehicles travelling outside the reach of the
sensors at close range from your own vehicle.
●
Vehicles that suddenly change to the lane on
which your vehicle is travelling.
●
Pedestrians that cannot be recognised be-
cause they are partially or totally hidden.
●
Objects such as walls, posts, fences, trees or
garage doors.
●
Loads and accessories of other vehicles that
protrude over the sides, backwards or over the
top.
●
In the case of pedestrians or cyclists standing
or approaching in the opposite direction.
Operating limitations
In the following situations, Front Assist may not
work, or may work in a limited or unwanted
way:
●
If Front Assist or the front camera are disa-
bled or broken.
●
If the radar sensor or the front camera are
dirty or covered.
●
On taking tight bends or complex paths.
●
When pressing the accelerator rmly or at
full throttle.
●
If the ESC is adjusting or is broken.
●
If several brake lights of the vehicle or electri-
cally connected trailer are damaged.
●
If the vehicle is reversing.
●
In case of snow or heavy rain.
●
In case of dazzling sun or total darkness.
●
Entrances and exits of tunnels.
●
In complex driving situations (such as traic
islands, cut-through roundabouts, etc.), Front
Assist may issue warnings and unnecessarily in-
tervene in braking.
For more details, see section ›››page194,
System limits.
Manual activation and deactivation
of the function
Front Assist indicators appear on the instru-
ment cluster display.
Front Assist is active whenever the ignition is
switched on. When the vehicle is started, Front
Assist may not be available for a short period of
Assistant systems
215
Lane Assist system
time while the system starts. During this phase,
the instrument cluster screen will display the
following indication .
When Front Assist is deactivated, so too are
the advance warning and the distance warning
functions.
CUPRA recommends leaving Front Assist ac-
tivated except in the situations explained in
section page215, Temporarily deactivating
Front Assist.
Activating and deactivating Front Assist
With the ignition switched on, Front Assist can
be deactivated or activated as follows:
●
In the infotainment system: press the func-
tion button > Driver assist > Smart Assis-
tants > Front Assist ›››page39.
●
OR: Select the corresponding menu option
using the button for the assistants systems
›››page194.
This indication will be displayed in the in-
strument cluster when Front Assist is de-
activated.
Each time the ignition is switched on, Front
Assist will reappear as active.
Switching distance warning on and o
The safety distance warning can be activated
or deactivated in the infotainment system us-
ing the function button
> Driver assist >
Smart Assistants > Front Assist ›››page39.
Each time the ignition is switched on, the dis-
tance warning will reappear as active.
CUPRA recommends having the safety dis-
tance warning activated, with the exceptions
described in section
page215, Temporarily
deactivating Front Assist.
Activating or deactivating the swerve and
turn and junction assist
The swerve and turn assistance systems can
be activated or deactivated in the infotain-
ment system using the function button >
Driver assist > Smart Assistants > Front Assist
›››page39.
Whenever the ignition is switched on, the
swerve and turn and junction assist will reap-
pear as active.
CUPRA recommends having the swerve and
turn assistance systems activated except in
the exceptions described in section page215,
Temporarily deactivating Front Assist .
Temporarily deactivating Front Assist
In the following situations Front Assist should
be deactivated due to the system's limitations:
●
When the vehicle is to be towed.
●
If the vehicle is on a test bed.
●
If the radar sensor or the front camera is
faulty.
●
If the radar sensor or the front camera has
suered a violent blow.
●
If it intervenes several times unnecessarily.
●
If the radar sensor or the front camera is
temporarily covered by an accessory.
●
When the vehicle is going to be loaded onto
transportation.
●
If the windscreen is damaged in an area that
covers the vision of the front camera.
Lane Assist system
Introduction
The Lane Assist System helps the driver stay
in his/her lane within the physical limits of the
system. This function is not suitable and is not
designed to keep the vehicle automatically in
the lane.
Using the camera located in the windscreen,
the Lane Assist system detects the lane boun-
daries dividing the lanes in which the vehi-
cle is travelling. If the vehicle gets too close
to the detected lane limits, the system alerts
the driver through a corrective motion of the
steering wheel. The driver can cancel the
steering corrective action at any time.
No warning will be given when the turn signals
are activated, given that the Lane Assist system
understands that a lane change is required.
System limits
Use the Lane Assist system only on large, well-
maintained motorways and highways.
Assistant systems
217
Lane Assist system
Control lamps
Lights up grey
Lane departure warning system
switched to passive and not available for
guidance.
Lights up green
Lane Assist system active and available.
Lights up yellow
The Lane Assist system is intervening by
adjusting the steering.
Switching the lane assist system on or o
In some countries, the Lane Assist system is
always activated when the ignition is switched
on. It is switched on and o and displayed in
the infotainment system’s Vehicle menu
and also in the driving assistants menu dis-
played on the instrument cluster, by pressing
the button on the multifunction steering
wheel.
The Lane Assist system is designed to actively
intervene as of approximately 65 km/h (40
mph) and if it has detected the lane bounda-
ries (system status: active).
When a turn signal is activated, the system
temporarily switches to a passive state in the
indicated direction and is available for opera-
tion in the opposite direction.
An energetic rotation or rectication of the
steering wheel by the driver causes the system
to temporarily switch to a passive state.
When Lane Assist is switched o, the yel-
low disconnection warning lamp lights up
in the instrument cluster (depending on
the country).
Note
If a system fault persists, Lane Assist may
switch o automatically.
Driver intervention prompt
If the steering is not corrected manually, the
system prompts the driver an indication on the
instrument cluster display and audible warn-
ings.
If no reaction is obtained from the driver, the
system switches to a passive state.
Depending on the equipment, Emergency As-
sist is activated.
Regardless of the steering manoeuvres, an in-
dication on the instrument cluster display and
audible warnings also prompt the driver to
drive in the middle of the lane if the steering
correction lasts longer than reasonable.
Steering wheel vibration
The following situations may result in a steering
wheel vibration:
●
The lane ceases to be recognised during a
sudden intervention in the steering by the sys-
tem.
It is also possible to select steering wheel vibra-
tion in the Vehicle menu of the infotainment
system. In this case, when a vehicle with Lane
Assist switched on crosses over a detected lane
marking, the steering wheel will vibrate.
Troubleshooting
The lane departure warning assistant
is not available
The control lamp lights up in yellow. A relevant
warning is also displayed on the instrument
cluster display.
●
There is a fault or a defect. Switch the engine
o and on again.
●
The eld of vision of the camera is dirty.
Clean the windscreen ›››page394.
●
The camera has decreased visibility due to
accessories or adhesives.
If the camera’s eld of view is aected by dirt,
snow, accessories, stickers or other obstruc-
tions, the following temporary message may
appear on the instrument cluster, accompa-
nied by an audible warning:
“ Driver assist limited now. Front sensors
without visibility.”
See more information on this topic in the
section “Drive assist sensors and cameras”
›››
page195.
218
Assistant systems
The system behaves dierently than expec-
ted
●
The camera has been altered or damaged,
e.g. because of damage caused to the wind-
screen. Check for visible damage.
●
Do not mount objects on the steering wheel.
If the problem persists, consult a specialised
workshop.
Note
After switching on the ignition, it may take a
few seconds before a fault is detected in the
system.
Note
If lane assist is not available, Emergency As-
sist and Travel Assist are not available either.
Travel Assist
Introduction
Travel Assist combines adaptive cruise control
(ACC) and the adaptive lane guidance func-
tion. Within the limitations of the system, the
vehicle can maintain a distance from the vehi-
cle in front that is preselected by the driver
and remain in the preferred position within the
lane.
Travel Assist uses the same sensors as Adaptive
Cruise Control (ACC) and Lane Assist. There-
fore, carefully read the information about
the ACC ›››
page204 and the Lane Assist
›››page215 and take into account the limita-
tions of the systems and the indications given
in the information.
How to know if the vehicle is tted with
Travel Assist
The vehicle is tted with Travel Assist if the
Travel Assist option appears in the instrument
cluster menu when the button on the multi-
function steering wheel is pressed.
Speed range
Travel Assist regulates at speeds between 20
and 210km/h (15 and 130mph).
Driving with Travel Assist
Travel Assist automatically controls the accel-
erator pedal, the brakes and the steering. In
addition, Travel Assist may, within its limita-
tions, decelerate the vehicle until it stops be-
hind another that stops, and automatically
start again.
You can override assisted adjustment at all
times.
Status display
Fig.142 On the instrument cluster display:
display of active regulation (schematic
representation).
1
The colour of the lane markings indicates
the status of the adaptive lane guidance
function.
●
Green: adaptive lane guidance function
active.
●
Grey: passive adaptive lane guidance
function.
2
Distance set.
Depending on the equipment, there is
also an indication on the Head-up-Display
›››
page22.
Depending on the equipment, additional de-
tails, e.g. dashed road markings and vehicles
in front, can also be shown on the instrument
cluster display.
Assistant systems
219
Travel Assist
Control lamps indicate the status of the system
on the instrument cluster display:
Indicator lamp green: Travel Assist ac-
tive, adaptive cruise control and adap-
tive lane guidance function are active.
Partially green lamp: Travel Assist ac-
tive, adaptive cruise control active and
adaptive lane guidance function pas-
sive.
Grey lamp: Travel Assist deactivated,
not regulating.
Driver intervention prompt
If you remove your hands from the steering
wheel, after a few seconds the system asks
you to take over the steering with an indication
on the instrument cluster display and audible
warnings.
If you do not react, Travel Assist is deactivated.
Depending on the equipment, Emergency As-
sist activates in its place.
WARNING
The Travel Assist smart technology cannot
overcome the limits imposed by the laws of
physics and it only works within the limits
of the system. If Travel assist is used negli-
gently or involuntarily, it may cause serious
accidents and injuries. The system is not a
replacement for driver awareness.
●
Bear in mind the system limitations and
the indications regarding the control of the
Adaptive Cruise Control (ACC) and Lane As-
sist.
●
Adapt your speed and safety distance to
the vehicle in front of you at all times to
suit visibility, weather, road and traic condi-
tions.
●
Do not use Travel Assist when visibility is
bad, on steep roads, on windy roads or in slip-
pery conditions (e.g., snow, ice, rain or loose
gravel), or on ooded roads.
●
Do not use Travel Assist oroad or on roads
where the surface is not rm. Travel Assist
has been designed for use on paved roads
only.
●
Travel Assist does not react to people or
animal or vehicles crossing your path or
which approach you head-on in the same
lane.
●
Brake immediately if Travel Assist does not
slow down enough.
●
Brake immediately when instructed to do
so on the instrument cluster display, or if
Travel Assist does not reduce speed sui-
ciently.
●
Brake when the vehicle continues to move
forward without it being desired after an indi-
cation to brake.
●
If possible, do not wear gloves while driv-
ing. The system could interpret this as no
driving activity.
●
If driver intervention is requested on the
instrument cluster display, immediately re-
sume control of the vehicle.
●
Keep your hands on the steering wheel
at all times, to ensure you always have con-
trol over the steering. The driver is always re-
sponsible for keeping the vehicle in its own
lane.
●
Always be prepared to adjust the speed
yourself.
Note
Online services provided and activated
through CUPRA CONNECT (depending on
device and country) may enhance the opera-
tion of Travel Assist when connected to the
Internet.
220
Assistant systems
Operating Travel Assist
Fig.143 Left side of the multifunction
steering wheel
Switch on and start regulation
The Travel Assist function is activated via the
driving assistance menu displayed on the in-
strument cluster.
1. Press the
button on the multifunction
steering wheel.
2. Then select the Travel Assist option from
the menu.
Depending on the driving situation, the vehi-
cle switches to the following system statuses in
Travel Assist:
●
If the ACC was already regulating, Travel As-
sist maintains the current speed and the preset
distance to the vehicle in front.
When lane markings are detected, the vehicle
is also kept in the lane by steering movements.
●
If ACC was not already regulating, Travel As-
sist remains selected but in a passive status
(not regulating).
Press the button.
Travel Assist switches to the active system sta-
tus, depending on the driving situation.
The indicator lamp for the driving situation
lights up on the instrument cluster display. A
message is also displayed.
Interrupting regulation
1. Briey press the button .
OR: press the brake pedal.
The set distance remains saved.
Making other adjustments
All other aspects of Travel Assist are controlled
like the ACC.
Troubleshooting
Travel Assist is not available or does
not work as expected
The control lamp lights up in yellow. A relevant
warning is also displayed on the instrument
cluster display.
●
There is a fault in the sensors. Check the
causes and solutions described in the informa-
tion about the ACC ›››page209 or the Lane
Assist ›››page217.
●
There is a fault or a defect. Switch the engine
o and on again.
●
The system limits are exceeded.
●
If the problem persists, consult a specialised
workshop. CUPRA recommends visiting a spe-
cialised CUPRA dealer or any SEAT dealership.
Grip the steering wheel
The warning lamp lights up white and a mes-
sage is then shown on the instrument cluster
display.
●
You released the steering wheel for a few
seconds. Take hold of the steering wheel and
take control of the vehicle.
Grip the steering wheel
The warning lamp lights up red and a message
is shown on the instrument cluster display. De-
pending on the situation, an audio warning
sounds or the steering wheel vibrates.
●
You have let go of the steering wheel for
a long time, or the system limits have been
reached. Immediately take hold of the steering
wheel and take control of the vehicle.
Travel Assist disconnects automatically
●
There is a fault or a defect. Switch the engine
o and on again.
●
If the problem persists, consult a specialised
workshop. CUPRA recommends visiting a spe-
cialised CUPRA dealer or any SEAT dealership.
Assistant systems
221
Emergency Assist
Emergency Assist
How it works
Emergency Assist can detect whether the
driver is inactive and can automatically keep
the car in its lane and stop it altogether if nec-
essary. This way the system can actively help
avoid an accident or reduce its consequences.
Emergency Assist uses the same sensors as
Adaptive Cruise Control (ACC) and Lane As-
sist Therefore, carefully read the information
about the ACC ›››
page204 and Lane Assist
›››page215 and take into account the limita-
tions of the systems and the indications given
in the information.
Emergency assist always available after the ig-
nition has been switched on and is activated if
the following conditions are met:
●
Travel Assist or Lane Assist is switched on.
●
The system has detected at least one lane
boundary to the left or right of the vehicle.
Note
If emergency assist is faulty, it may switch o
automatically.
Note
If Lane Assist is unavailable, Emergency Assist
is also unavailable.
Driver intervention prompt
If Emergency Assist detects that the driver
is not actively doing anything, he or she is
prompted to take control of the vehicle by
audio warnings and a brief application of the
brake. In addition, a warning is shown on the
instrument cluster display and the volume of
the infotainment system is lowered.
Depending on the equipment, the driver’s seat
belt is tightened at the same time.
System intervention
If the driver does not react, the system can
brake the vehicle and keep it in its lane. The
following control lamp lights up on the instru-
ment cluster display:
The system is regulating, lane guidance
is activated.
The system is regulating, passive lane
guidance.
You can cancel the adjustment at any time by
moving the steering wheel, over-accelerating
or braking.
While the emergency assistant is in operation,
other road users are warned as follows:
●
The hazard warning lights are switched on
soon after.
●
The horn sounds (depending on the speed).
The following happens as soon as the vehicle
stops:
●
The electronic parking brake and gear shift
position P are engaged.
●
All doors are unlocked.
●
The vehicle interior lighting comes on.
●
Depending on the features, an emergency
call (eCall) is made.
WARNING
The Emergency Assist smart technology can-
not overcome the limits imposed by the laws
of physics; it only works within the limits of
the system. The driver is responsible for driv-
ing the vehicle.
●
Adapt your speed and safety distance to
the vehicle in front of you at all times to suit
the visibility, weather, road and traic condi-
tions.
●
Emergency Assist cannot always avoid acci-
dents or serious injuries by itself.
●
If the radar sensor or the camera are cov-
ered or have been altered or damaged, the
system may inappropriately apply the brakes
or intervene in the steering.
●
The Emergency Assist does not react to
people or animal or vehicles crossing your
path or which approach you head-on in the
same lane.
222
Assistant systems
WARNING
If Emergency Assist intervenes inoppor-
tunely, serious accidents and injuries may
occur.
●
If the vehicle behaves dierently than ex-
pected, interrupt the intervention of the
Emergency Assist by over-accelerating, brak-
ing or moving the steering wheel.
●
Do not use Travel Assist or Lane Assist.
Have the system checked by a specialised
workshop.
Troubleshooting
Emergency Assist not available
The control lamp lights up in yellow. A relevant
warning is also displayed on the instrument
cluster display.
●
There is a fault or a defect. Turn the drive
system o and on again.
●
If the problem persists, switch o the Emer-
gency Assist and go to a specialised workshop.
Lane departure warning
(Side Assist)
Introduction
The lane departure warning uses radar sen-
sors to monitor the areas behind the vehicle
›››
page6. The system does this by measuring
the vehicle's distance from other vehicles and
its speed dierential. The lane departure warn-
ing will not work at speeds of less than approx.
15km/h (9mph).
Lane width is not detected individually, but is
rather pre-congured in the system. Thus if
you are driving in wide lanes or in between
two lanes, the indications may be incorrect.
Furthermore, the system can detect vehicles
driving in the lane next to you (if there are any),
and can also detect stationary objects such as
dividers, and thus give an incorrect indication.
Trailer mode
Side assist is automatically deactivated and
cannot be switched on if the factory-tted
tow-bar is electrically connected to a trailer or
similar device.
As soon as the driver starts to drive with a
trailer connected electrically to the vehicle, a
message is displayed on the instrument cluster
display indicating that side assist is switched
o. Once the vehicle trailer has been disen-
gaged, side assist will return to the initial state
prior to the moment the trailer was electrically
connected.
If the tow-bar is not factory tted, side assist
should be switched o manually when driving
with a trailer.
Physical limitations inherent to the system
In some situations the lane departure warning
may not interpret the traic situation correctly.
I.e. in the following situations:
●
on tight bends;
●
in the case of lanes with dierent widths;
●
in areas with signicant gradient changes;
●
in adverse weather conditions;
●
in the case of special constructions to the
side of the vehicle, e.g., high or irregular divid-
ers.
WARNING
The smart technology incorporated into Side
Assist cannot overcome the limits imposed
by the laws of physics; it only works within the
limits of the system. Accidents and severe
injury may occur if Side Assist is used negli-
gently or involuntarily. The system is not a
replacement for driver awareness.
●
Adapt your speed and safe distance to the
vehicle in front of you at all times to suit visi-
bility, weather, road and traic conditions.
Assistant systems
223
Lane departure warning (Side Assist)
●
Keep your hands on the wheel at all times
to be ready to intervene in the steering at any
time.
●
Pay attention to the control lamps that may
come on in the external interior mirrors and
on the instrument cluster, and follow any in-
structions they may give.
●
The lane departure warning could react to
any special constructions that might be pres-
ent to the sides of the vehicle, e.g. high or
irregular dividers. This may cause erroneous
warnings.
●
Never use the lane departure warning on
unpaved roads. The lane departure warning
has been designed for use on paved roads.
●
Always pay attention to the vehicle's sur-
roundings.
●
The control lamps of the lane departure
warning may have limited functionality due
to solar radiation.
Note
If Side Assist does not work as described in
this chapter, stop using it and contact a spe-
cialised workshop.
Driving with Side Assist
Fig.144 Control lamp of the lane departure
warning.
Fig.145 Control lamp of the lane departure
warning.
Connecting and disconnecting
Side Assist can be switched on and o by ac-
cessing the Assistants menu in the infotain-
ment system.
Additionally it can be switched on and o by
accessing the Assistants menu on the instru-
ment cluster.
When the lane departure warning is ready to
operate, the indications in the control lamps
will turn on briey as conrmation.
When the vehicle is restarted, the last adjust-
ment in the system will remain active.
Light indication
The control lamp provides an indication on the
corresponding side regarding the traic situa-
tion behind the vehicle, if it is deemed to be
critical. The control lamp on the left-hand side
indicates the traic situation to the rear left of
the vehicle, and the control lamp on the right-
hand side indicates the traic situation to the
rear right of the vehicle .
Keep the warning lamps zone of the lane de-
parture warning free of objects, stickers or the
likes that may interfere with your visibility.
It lights up
It turns on once briey: the lane departure
warning is activated and ready to operate, i.e.
when activating the system.
It lights up continuously: the lane departure
warning has detected a vehicle in the blind
spot.
224
Assistant systems
Flashes
A vehicle has been detected in the adjacent
lane and the turn signal has been engaged in
the direction of the detected vehicle.
For vehicles that are also equipped with Lane
Assist ›››page215, a warning to switch lanes
will also appear even though the turn signal
has not been engaged (Lane Assist “Plus”).
The control lamps light up when the ignition is
switched on and should turn o after approxi-
mately 2 seconds. This is the time taken for the
function check.
If there are no indications from the control
lamp of the lane departure warning, this means
that the lane departure warning has not detec-
ted any other vehicles at the rear area.
When the exterior lighting is low, the intensity
with which the control lamps come on is dim-
med. The user can modify the intensity of the
control lamps with up to 5 levels in the infotain-
ment system menu.
Lane assist Plus.
The Lane Assist Plus function can be used by
activating the Lane Assist ›››page215 and
Side Assist functions. In this case its functions
are expanded as described below.
If the driver initiates a lane change manoeuvre
in a potential critical situation:
●
The lamp ashes in the corresponding rear-
view mirror even though the turn signal has not
been activated.
●
The steering wheel vibrates to warn the
driver of the risk of collision.
●
torque is applied to correct the steering and
return the vehicle to its lane.
Driving situations
Fig.146 Overtaking with traic behind the
vehicle.
Fig.147 Overtaking in the central lane and
then joining the right lane.
In the following situations, an indication will be
displayed by the control lamp ›››
Fig.144 ,
›››Fig.145 (arrow):
●
When being overtaken by another vehicle
›››Fig.146.
●
When overtaking another vehicle
›››Fig.147 with a speed dierence of approx.
10 km/h (6 mph). If the vehicle is passing at
a considerably higher speed, no indication will
be displayed.
The faster the vehicle approaches, the sooner
an indication will be displayed in the control
lamp, because the lane departure warning
takes into account the speed dierential with
other vehicles. Thus even though the distance
from the other vehicle is identical, the indica-
tion will appear sooner in some cases and later
in others.

Related Topics

Popular Owner Manuals