Get Starting And Operating -> Active Speed Limiter Guide for Fiat 500 E 4 Door Second Generation (2020-2024)

74 STARTING AND OPERATING

NOTE:

handling with a smoother response to accelerator pedal

pressure. This mode helps to adopt a driving style

aimed at maximizing the range.

Refer to “Warning Lights And Messages” in “Getting To

Know Your Instrument Panel” for further information.

● The system does not allow you to change the driving

mode when you drastically reduce the performance

of the electric motor.

If the Electric Power Steering warning icon is displayed

and the “Power Steering System Over Temp” message

is displayed on the instrument cluster display, this

indicates an over temperature condition in the power

steering system. Once driving conditions are safe, pull

over and let the vehicle idle for a few moments until the

icon and message turn off.

SHERPA Mode – In this mode the vehicle has

no acceleration restriction but the top speed is

electronically limited to 50 mph (80 km/h). This mode

significantly helps to adopt a driving style aimed at

maximum efficiency and maximizes the range of the

vehicle. The climate control system and seat heaters

are also automatically deactivated but can be manually

reactivated if necessary.

● When the motor is started, the system usually

maintains the driving mode that was active before

the vehicle was stopped.

The E-Mode Selector is located on the central console.

NOTE:

● Even if the power steering assistance is no longer

operational, it is still possible to steer the vehicle.

Under these conditions there will be a substantial

increase in steering effort, especially at low speeds

and during parking maneuvers.

POWER STEERING

The electric power steering system will provide

increased vehicle response and ease of

maneuverability. The electric power steering system

adapts to different driving conditions.

● If the condition persists, see an authorized dealer for

service.

WARNING!

ACTIVE SPEED LIMITER

The Active Speed Limiter button is positioned on the

right side of the steering wheel.

Continued operation with reduced assist could pose

a safety risk to yourself and others. Service should be

obtained as soon as possible.

E-Mode Selector

The E-Mode Selector consists of the following operating

modes:

Alternate electric power steering efforts can be selected

through the Uconnect system. Refer to ”Customer

Programmable Features” within “Uconnect Settings” in

“Multimedia” for further information.

NORMAL Mode – In this mode the vehicle has no

performance limitations and can be driven fast using

all the power and torque of the traction system. In this

mode the energy consumption of the vehicle depends

on the driving style.

If the Electric Power Steering warning icon is

displayed and the “Service Power Steering”

or the “Power Steering Assist Off – Service

RANGE Mode – In this mode the vehicle continues

to have no speed restrictions but offers comfortable

System” message is displayed within the

instrument cluster display, this indicates the vehicle

needs to be taken to an authorized dealer for service.

STARTING AND OPERATING 75

to set the target speed (or RES button when there is

already a previously set target).

message will appear in the instrument cluster display to

confirm that the feature has been turned off. You can

also deactivate Active Speed Limiter by pressing the

CANC button. In this case, the system is not completely

turned off, and the driver can reactivate the Active

Speed Limiter by pressing the RES button.

Push the SET (+) or SET (–) button to raise or lower the

target speed to the desired value, speed will increase/

decrease by 1 mph (1 km/h). Pushing and holding

down the SET (+) or SET (–) button will increase/

decrease the speed value by increments of 5 mph (10

km/h).

NOTE:

In the event of a system failure, the Active Speed

Limiter will switch off automatically and the indicator

light will switch to grey. In this event, please see an

authorized dealer.

Each time that Active Speed Limiter is activated, it will

be set to the last programmed value from the previous

activation.

Active Speed Limiter Button

NOTE:

INTELLIGENT SPEED ASSIST (ISA)

The Cruise Control (if equipped) and Adaptive Cruise

Control (if equipped) systems will be unavailable while

the Active Speed Limiter is in use.

This feature allows you to program the maximum speed

of travel for your vehicle.

The Intelligent Speed Assist (ISA) system

combines the Active Speed Limiter and

Traffic Sign Assist (TSA) systems to

NOTE:

The Active Speed Limiter can be set with the vehicle

stationary or in motion. The minimum speed it can be

set to is 18 mph (30 km/h).

EXCEEDING THE SET SPEED

By fully pressing the accelerator pedal, the

programmed maximum speed can be exceeded while

the device is active.

automatically adjust the maximum speed of

the vehicle based on detected traffic signs.

The Active Speed Limiter can be set with the vehicle

stationary or in motion. The minimum speed it can be

set to is 18 mph (30 km/h).

ACTIVATION

In the event that the Active Speed Limiter set value

is exceeded manually with a driver acceleration, an

audible indicator will sound. The indicator light will

rapidly flash, and a message will appear in the

instrument cluster display.

To activate the feature, push the Active Speed Limiter

button located on the right side of the steering wheel. A

message will appear along with an indicator light in the

instrument cluster display to signal that Active Speed

Limiter has been activated.

ACTIVATION

To activate the feature, make sure the Traffic Sign

Assist (TSA) system is enabled within Uconnect Settings

page 113, then push the Active Speed Limiter

The feature will remain disabled until the vehicle speed

drops below the set Active Speed Limiter value, where it

will reactivate automatically.

NOTE:

button located on the right side of the steering wheel.

The message “Ready” will appear along with a white

indicator light in the instrument cluster display to signal

that the system has been activated.

If Cruise Control or Adaptive Cruise Control are active,

press the Active Speed Limiter button twice. The first

press will switch off the active function; the second

press will activate the speed limiter.

DEACTIVATION

To turn off Active Speed Limiter, push the Active Speed

Limiter button on the right side of the steering wheel. A

After the Active Speed Limiter on/off button has been

pushed, you must press the SET (+) or SET (–) button

Starting And Operating -> Active Speed Limiter for Your Fiat 500 E 4 Door Second Generation (2020-2024)

Related Topics

Starting And Operating

Popular Owner Manuals

Latest Owner Manuals