Get Starting And Operating -> Lanesense Guide for Fiat 500 E 4 Door Second Generation (2020-2024)

106 STARTING AND OPERATING

CAUTION!

If the vehicle continues to drift beyond the lane

boundary without any driver intervention, a warning

light will illuminate on the instrument cluster display,

urging the driver to steer the car back into the lane’s

boundaries.

CHANGING LANESENSE STATUS

The LaneSense system has settings to adjust the

intensity of the torque warning and the warning zone

sensitivity (early/medium/late) that you can configure

above or below the sensors will not be detected

when they are in close proximity.

● The vehicle must be driven slowly when using

ParkSense in order to be able to stop in time when

an obstacle is detected. It is recommended that

the driver looks over his/her shoulder when using

ParkSense.

through the Uconnect system screen

page 113.

NOTE:

The LaneSense system is operational at speeds above

37 mph (60 km/h) and below 93 mph (150 km/h).

The LaneSense system uses a forward facing camera

to detect lane markings and measure vehicle position

within the lane boundaries.

NOTE:

Once active, the system will operate when the following

conditions are met:

● The driver maintains at least one hand on the

steering wheel at all times.

LANESENSE — IF EQUIPPED

TURNING LANESENSE ON OR OFF

● The vehicle's speed falls within the range of 37 mph

to 93 mph (60 km/h to 150 km/h).

LANESENSE OPERATION

The LaneSense button is located on the end

of the turn signal stalk, located on the left

side of the steering column.

● The lane is marked on at least one side.

● Visibility conditions are appropriate.

The LaneSense system utilizes a windshield-mounted

camera to identify lane boundaries and determine the

car’s position within those boundaries, ensuring it stays

within the lane.

To turn the LaneSense system on, push the

LaneSense button once. A “Lane Sense On” message is

shown in the instrument cluster display.

● The road is straight or with wide radius bends.

● The turn signal is not engaged in the same direction

as the lane departure.

When one of the lane markings are detected and the

driver drifts out of the lane (no turn signal applied),

the LaneSense system provides a haptic warning in

the form of torque applied to the steering wheel to

prompt the driver to remain within the lane boundaries.

If the driver continues to drift out of the lane, the

LaneSense system provides a visual warning through

the instrument cluster display to prompt the driver to

remain within the lane boundaries.

To turn the LaneSense system off, push the LaneSense

button twice within 5 seconds.

NOTE:

The system will not apply torque to the steering wheel

whenever a safety system engages. (Anti-Lock Brakes,

Traction Control System, Electronic Stability Control, Full

Brake Control system, etc.).

On some models, when LaneSense is disabled, a

message along with a warning light will be displayed

on the instrument cluster display.

NOTE:

LANESENSE WARNING MESSAGE

The LaneSense system alerts the driver when the

car drifts out of its lane by displaying symbols and

messages on the instrument panel display.

The system will retain the last state (on or off) that

was active during engine shut down. The next time the

engine is started, the system will either be active or

stay off.

NOTE:

The torque applied to the steering wheel by the system

is sufficient for the driver to notice it, but always limited,

so that they can easily override it. The driver may

manually override the haptic warning by applying force

to the steering wheel at any time.

While the system is in operation and hasn't detected

the lane boundaries, the lane lines appear in grey, and

a specific icon is displayed in the dedicated upper

section of the display.

STARTING AND OPERATING 107

Lane Approached (Flashing

Yellow Line/Flashing Yellow Telltale)

Lanes Sensed (White Lines/Green Telltale)

System On (Gray Lines/White Telltale)

NOTE:

Single Lane Departure — Only Left Lane Detected

NOTE:

Based on the various conditions it detects, the

system can grab the driver's attention by modifying

the characteristics of the lane identification lines on

the display. Specifically, it can change their color

(from white to yellow and vice versa) and make them

flash. Additionally, the system adjusts the color of

the car icon displayed on the screen as needed.

● When the system is active and has detected only

the left lane, the car icon is displayed in the

dedicated area of the screen. In this state, the

system is prepared to deliver visual warnings in case

of unintentional lane departure to the left (with no

direction indicator activation).

● The LaneSense system operates with similar

behavior for a right lane departure when only the

right lane marking has been detected.

● The system will only provide visual warnings and will

not make steering corrections to realign the car's

path.

● When the LaneSense system senses a lane drift

situation, the left lane line turns solid yellow. The

LaneSense telltale changes from solid green to solid

yellow. At this time torque is applied to the steering

wheel in the opposite direction of the lane boundary.

● As the system detects the car's proximity to the lane

line, the left lane line on the display turns yellow,

and the car icon displayed also turns yellow. If the

system detects that the car is approaching the lane

line and is about to cross it, the left lane line (in

yellow) flashes, and the car icon displayed also turns

yellow.

Lane Departure — Both Lanes Detected

● When the LaneSense system is on, the lane lines

turn from gray to white to indicate that both of the

lane markings have been detected. The LaneSense

telltale is solid green when both lane markings have

been detected and the system is ready to provide

visual warnings in the instrument cluster display and

a torque warning in the steering wheel if a lane

departure occurs.

For example: If approaching the left side of the lane

the steering wheel will turn to the right.

108 STARTING AND OPERATING

driven under normal conditions, the system may not be

fully available.

note will disappear. The ParkView camera is located on

the rear of the vehicle on the boot tailgate.

Once the conditions restricting the system's functions

are resolved, it will return to its normal and complete

operation. However, if the fault continues, it's advisable

to get in touch with an authorized dealer for further

assistance.

No Hands On Steering Wheel Detection

When the system detects the absence of hands on

the steering wheel during active system intervention, it

will initiate a series of escalating visual and acoustic

warnings. This process will span 15 seconds, with the

goal of prompting the driver to place their hands back

on the steering wheel.

Lane Sensed (Solid

Yellow Line/Solid Yellow Telltale)

● When the LaneSense system senses the lane

has been approached and is in a lane departure

situation, the left lane line flashes yellow (on/off).

The LaneSense telltale changes from solid yellow to

flashing yellow. At this time torque is applied to the

steering wheel in the opposite direction of the lane

boundary.

Back Up Camera Location

If the driver does not return their hands to the

wheel within this 15-second window, the system will

disengage and issue an additional warning lasting 5

seconds.

When the vehicle is shifted out of REVERSE with

camera delay turned off, the rear camera mode is

exited and the navigation or audio screen appears

again.

System Fault

When the vehicle is shifted out of REVERSE with

camera delay turned on, the camera image will

continue to be displayed for up to 10 seconds unless

the vehicle speed exceeds 8 mph (13 km/h), the

vehicle is shifted into PARK, or the ignition is placed

in the OFF position.

If the system deactivates and displays a message on

the instrument cluster display, it signifies a fault within

the system. It is still possible to drive the car, but it is

strongly recommended that you contact an authorized

dealer.

For example: If approaching the left side of the lane

the steering wheel will turn to the right.

System Limited Operation Warning

If a dedicated message appears on the display, it

could indicate a condition that limits the system's

operation. Possible reasons for this limitation include

an obstruction blocking the camera's view or a system

fault.

A touchscreen button to disable the camera is available

when the vehicle is not in REVERSE. Display of the

camera image after shifting out of REVERSE can be

disabled via Uconnect Settings.

PARKVIEW REAR BACK UP CAMERA

The ParkView Rear Back Up Camera allows you to see

an on-screen image of the rear surroundings of your

vehicle when the gear selector is put into REVERSE.

The image will be displayed on the touchscreen display

along with a note to “Check Entire Surroundings”

across the top of the screen. After five seconds this

If an obstruction is detected, clean the area of the

windshield near the interior rearview mirror and verify

if the message disappears. Even if the car can still be

When enabled, active guidelines are overlaid on the

image to illustrate the width of the vehicle and its

projected back up path based on the steering wheel

position.

Starting And Operating -> Lanesense for Your Fiat 500 E 4 Door Second Generation (2020-2024)

Related Topics

Starting And Operating

Popular Owner Manuals

Latest Owner Manuals