Get Driving -> Cruise control Guide for Fiat Scudo Van Third Generation (2022-2025)

Driving

Exceeding the programmed speed

The new speed setting value is displayed on the

instrument panel.

In the event of a malfunction, dashes are

displayed ﬂashing and then ﬁxed instead of the

speed setting.

Have it checked by a Fiat Dealership or a

qualiﬁed workshop.

setting

You can temporarily exceed the speed

setting by pressing the accelerator pedal (the

programmed speed ﬂashes).

To return to the speed setting, release the

accelerator pedal (when the set speed is

reached again, the displayed speed stops

ﬂashing).

Temporarily exceeding the

programmed speed

► To temporarily exceed the programmed

speed threshold, fully depress the accelerator

pedal.

The speed limiter is deactivated temporarily and

the displayed programmed speed ﬂashes.

If it is exceeded for a prolonged period of time,

an audible warning is triggered.

Simply release the accelerator pedal to return to

below the programmed speed.

When the limit speed is exceeded but this is not

due to action by the driver (in case of a steep

slope, for example), an audible signal triggers

immediately.

Once the speed of the vehicle returns to the

programmed setting, the speed limiter functions

again: the display of the programmed speed

setting becomes ﬁxed again.

Cruise control - Speciﬁc

recommendations

The cruise control function does not

guarantee compliance with the maximum

authorised speed and the safety distance

between vehicles, the driver remains

responsible for their driving.

In the interest of public safety, only use cruise

control if the traﬃc conditions enable vehicles

to drive at a steady speed and maintain an

adequate safety distance.

Remain vigilant while cruise control is

activated. If you press and hold one of the

speed setting modiﬁcation buttons, your

vehicle may change speed very abruptly.

When descending a steep hill, the cruise

control system cannot prevent the vehicle

from exceeding the set speed. Brake if

necessary to control the vehicle speed.

On steep climbs or when towing, the set

speed may not be reached or maintained.

Operating limits

Never use the system in the following

situations:

– In an urban area with the risk of

pedestrians crossing the road.

– In heavy traﬃc.

– On winding or steep roads.

– On slippery or ﬂooded roads.

– In poor weather conditions.

– In the event of restricted visibility for the

driver.

– Driving on a speed circuit.

– Driving on a rolling road.

– When using snow chains, non-slip covers

or studded tyres.

Switching oﬀ

► Turn the thumbwheel 1 to the "0" position:

the display of information on the speed limiter

disappears.

Cruise control

Malfunction

For more information, refer to the

General recommendations on the use

of driving and manoeuvring aids and the

157

Driving

Cruise control - Speciﬁc

recommendations.

Steering-mounted control

Information displayed on

the instrument panel

This system automatically maintains the

vehicle’s speed at the value programmed

by the driver (speed setting), without the use of

the accelerator pedal.

Cruise control is switched on manually.

It requires a minimum vehicle speed of 25 mph

(40 km/h).

With a manual gearbox, third gear or higher must

be engaged.

With an automatic gearbox, mode D or second

gear or higher in mode M must be engaged.

With a drive selector, mode D or B must be

engaged.

1. ON (CRUISE position)/OFF (position 0)

2. Activate cruise control at the current speed/

decrease speed setting

3. Activate cruise control at the current speed/

increase speed setting

Head-up display

Cruise control remains active after

changing gear, regardless of the gearbox

type, on engines ﬁtted with the Stop & Start

function.

4. Pause/resume cruise control with the speed

setting previously saved

5. Depending on version:

Display the speed thresholds saved using the

Memorising speeds function

Switching oﬀ the ignition cancels any

Use the speed suggested by the Road signs

recognition function (MEM display)

speed setting.

6. Cruise control pause/resume indication.

7. Cruise control mode selection indication.

8. Speed setting value.

For more information on Memorising speeds

or the Road signs recognition, refer to the

corresponding sections.

Switching on/pausing

► Turn thumbwheel 1 to the "CRUISE" position

to select cruise control mode; the function is

paused.

158

Driving

To return to the programmed speed, simply

► Press button 2-SET- or 3-SET+ to activate

cruise control and save a speed setting when

the vehicle has reached the desired speed; the

vehicle’s current speed is saved as the speed

setting.

► Release the accelerator pedal.

► Pressing button 4-II temporarily pauses the

function (pause).

As a precaution, we recommend setting

a cruise speed fairly close to the current

speed of your vehicle, to avoid any sudden

acceleration or deceleration of the vehicle.

release the accelerator pedal.

Once the vehicle has returned to the

programmed speed, cruise control takes over

again and the programmed speed setting stops

ﬂashing.

To change the cruise speed setting using

memorised speed settings and from the touch

screen:

► Press 5-MEM to display the memorised

speed settings.

► Press the touch screen button for the desired

speed setting.

The selection screen closes after a few

moments.

When descending a steep hill, the cruise

control system cannot prevent the

vehicle from exceeding the programmed

speed.

You may have to brake to control the speed of

your vehicle. In this case, the cruise control is

automatically paused.

► Pressing button 4-II again resumes operation

of the cruise control (ON).

Cruise control can also be paused

temporarily:

– by pressing the brake pedal.

– by pressing the clutch pedal with a manual

gearbox (depending on the engine ﬁtted).

– automatically, if the electronic stability

control (ESC) system is triggered.

To activate the system again, with the vehicle

speed above 25 mph (40 km/h), press button

This setting becomes the new cruise speed.

To change the cruise speed setting using the

speed suggested by the Road signs recognition

function displayed on the instrument panel:

► Press 5-MEM once; a message is displayed,

conﬁrming the memorisation request.

► Press 5-MEM again to save the suggested

speed.

Switching oﬀ

► Turn the thumbwheel 1 to the "0” position: the

cruise control information disappears from the

screen.

Changing the cruise speed

setting

The cruise control must be active.

To change the cruise speed setting, based on

the vehicle’s current speed:

The new speed setting value is displayed on the

instrument panel.

Malfunction

Temporarily exceeding the

programmed speed

If needed (when overtaking, for example),

it is possible to exceed the programmed

speed by pressing the accelerator pedal.

Cruise control is temporarily deactivated and the

programmed speed displayed ﬂashes.

► For steps of +/- 1 mph (1 km/h), brieﬂy

press 2-SET- or 3-SET+ repeatedly.

► For steps of +/- 5 mph (5 km/h), press and

hold 2-SET- or 3-SET+.

In the event of a malfunction, dashes are

displayed ﬂashing and then ﬁxed instead of the

speed setting.

Have it checked by a Fiat Dealership or a

qualiﬁed workshop.

Pressing and holding 2-SET- or 3-SET+

results in a rapid change in the speed of

the vehicle.

159

Download User Manual App

Driving -> Cruise control for Your Fiat Scudo Van Third Generation (2022-2025)

Related Topics

Driving

Popular Owner Manuals

Latest Owner Manuals