Get Ease of use and comfort -> Moduwork Guide for Fiat Scudo Van Third Generation (2022-2025)

Ease of use and comfort

► Lock the vehicle from the outside.

Rear view mirror

Equipped with an anti-dazzle system, which

darkens the mirror glass and reduces the

nuisance to the driver caused by the sun,

headlamps of other vehicles, etc.

If the mirrors are folded using control A,

they will not unfold when the vehicle is

unlocked.

Electric unfolding

Day/night position

The door mirrors are unfolded electrically when

the vehicle is unlocked using the remote control

or key. Unless folding was selected with control

A, pull the control in the central position towards

the rear again.

For the version without athermic

windscreen, to limit the obstruction of you

ﬁeld of vision through the windscreen, we

recommend you to place the toll badge in the

upper part of the windscreen.

Folding/unfolding when locking/unlocking

the vehicle can be deactivated. Contact a

Fiat Dealership or a qualiﬁed workshop.

If necessary, the mirrors can be folded

manually.

► Pull the lever to change to the anti-dazzle

"night” position.

► Push the lever to change to the normal "day"

position.

Moduwork

Heated mirrors

Windscreen zone for toll

badge

The cushion of the bench seat's outer seat can

be folded up against the backrest to create a

loading area inside the cab.

A removable ﬂap on the partition can be

removed to allow long objects to be loaded.

Depending on the version, the vehicle can be

equiped with a athermic windscreen type.

For a best functionnement of the toll badge

system, it is necessary to place the toll badge on

the zone of windscreen provided for the purpose

symbolised with of black dotteds around of the

interior rear view mirror base.

► Press one of these buttons.

For more information on Rear screen

demisting/de-icing, refer to the

corresponding section.

52

Ease of use and comfort

► While holding the ﬂap with one hand, turn the

control at the top of the ﬂap with the other hand

to release it.

► Lower the ﬂap to remove it from its housing.

► Stow it behind the driver’s seat, clipping it into

the attachment lugs.

Removable ﬂap (type 2)

3

► Turn the control at the top of the ﬂap to

secure it.

Reﬁtting the ﬂap

Once the removable ﬂap has been

removed, you can load long objects

under the outer seat.

► To open or close the ﬂap, slide it to the left

or right.

The ﬂap is kept in the closed or open position

with magnets located at each end position.

Removable ﬂap (type 1)

Removing the ﬂap

Folding seat cushion

Raising the seat cushion

► Tilt the ﬂap, with the yellow hinges pointing

downwards.

► Insert the hinges into their housing then press

down fully (to avoid vibrations).

► With one hand lift the ﬂap to close it, then

with the other hand turn the control at the top of

the ﬂap to secure it.

► With one hand, ﬁrmly pull the strap forwards

to unlock the seat cushion.

► A strut lifts the seat cushoin against the

backrest.

53

Ease of use and comfort

Never put your hand underneath the seat

cushion to guide it upwards, as your

ﬁngers may become trapped.

Always use only the strap.

Lowering the seat cushion

Anti-slip net

Installing the net

When the outer seat is raised and the

ﬂap is removed, you must install the

anti-slip net.

Refer to the Anti-slip net section.

► Remove the anti-slip net.

► To reposition the seat cushion, press ﬁrmly

on the top of the seat with one hand to lower the

seat cushion until it locks into the seat position.

Ensure that there are no objects or feet

obstructing the anchorage points or

preventing the assembly from locking

properly.

► Put the ﬁrst fastener into the upper cut-out 1,

located beneath the folded seat cushion. Keep

the fastener pressed against the structure, then

54

Ease of use and comfort

turn it a quarter turn (in a clockwise direction) to

lock it.

► Put the second fastener into the lower cut-out

2, located on the seat base. Keep the fastener

pressed against the structure, then turn it a

quarter turn (in a clockwise direction) to lock it.

Install the anti-slip net (supplied with the

vehicle) every time that the seat is raised and

the partition ﬂap removed.

3

Never use the net for any other purposes.

Regularly check the condition of the anti-

slip net. As soon as signs of wear or tear

appear, contact a Fiat Dealership to have it

replaced by an anti-slip net that meets the

speciﬁcations required by Fiat for the vehicle.

Always ﬁt the removable ﬂap back into place

when you are not carrying any long loads.

"Rotating writing table"

► Secure the ﬁrst hook to the ring 3 located in

the glove box.

► Secure the second hook to the ring 4 located

on the ﬂoor.

Never use the table while the vehicle is

being driven.

In the event of sudden braking or impact, any

objects on the table might become dangerous

projectiles that could cause injury.

If ﬁtted to your vehicle, the central seat cushion

of the bench seat can be tilted to form a pivoting

writing table, thus creating a mobile desk (with

the vehicle stationary).

Removing the net

► Pull the handle located at the top of the

backrest cushion.

► Release the hooks from the rings 4 and 3.

► Remove the lower fastener 2 then the upper

fastener 1, turning them by a quarter turn

backwards to unlock them.

Make sure that the size, shape and

volume of the loads carried are

compatible with the highway code and safety

regulations and do not impair the driver’s ﬁeld

of vision.

All loads must be appropriately secured

to prevent or minimise displacement and

prevent injury.

55

Download User Manual App

Ease of use and comfort -> Moduwork for Your Fiat Scudo Van Third Generation (2022-2025)

Related Topics

Ease of use and comfort

Popular Owner Manuals

Latest Owner Manuals