Get Maintenance Guide for Hyundai Bayon SUV Second Generation (2021-2024)

9. Maintenance

Engine compartment .........................................................................................9-3

Maintenance services ....................................................................................... 9-4

Owner’s responsibility.................................................................................... 9-4

Owner maintenance precautions.................................................................. 9-4

Owner maintenance...........................................................................................9-5

Owner maintenance schedule .......................................................................9-5

Scheduled maintenance services .....................................................................9-7

Explanation of scheduled maintenance items................................................ 9-8

Engine oil............................................................................................................9-11

Checking the engine oil level ........................................................................9-11

Checking the engine oil and filter................................................................ 9-12

Engine coolant.................................................................................................. 9-14

Checking the coolant level ........................................................................... 9-14

Changing the engine coolant....................................................................... 9-16

Brake/Clutch fluid..............................................................................................9-17

Checking the brake/clutch fluid level...........................................................9-17

Washer fluid ...................................................................................................... 9-19

Checking the washer fluid level ................................................................. 9-19

Parking brake ................................................................................................... 9-19

Checking the parking brake.......................................................................... 9-19

Air cleaner ........................................................................................................ 9-20

Filter replacement........................................................................................ 9-20

Climate control air filter ...................................................................................9-22

Filter inspection.............................................................................................9-22

Filter replacement.........................................................................................9-22

Wiper blades .....................................................................................................9-24

Blade inspection............................................................................................9-24

Blade replacement ......................................................................................9-24

9

Battery ...............................................................................................................9-26

For best battery service ................................................................................9-26

Battery capacity label ..................................................................................9-28

Battery recharging.........................................................................................9-28

Reset items ....................................................................................................9-29

Tyres and wheels.............................................................................................. 9-30

Tyre care........................................................................................................ 9-30

Recommended cold tyre inflation pressures ............................................. 9-31

Check tyre inflation pressure........................................................................ 9-31

Tyre rotation .................................................................................................9-32

Wheel alignment and tyre balance..............................................................9-33

Tyre replacement...........................................................................................9-33

Wheel replacement ......................................................................................9-35

Tyre traction ..................................................................................................9-35

Tyre maintenance..........................................................................................9-35

Tyre sidewall labelling ...................................................................................9-35

Low aspect ratio tyres.................................................................................. 9-38

Fuses................................................................................................................. 9-39

Instrument panel fuse replacement ........................................................... 9-40

Engine compartment panel fuse replacement........................................... 9-41

Fuse/relay panel description....................................................................... 9-42

Light bulbs........................................................................................................ 9-56

Headlight, position light, turn signal light, fog light and daytime

running light, low beam assist-static light bulb replacement ..................9-57

Headlight and front fog light aiming............................................................9-61

Side repeater light replacement.................................................................. 9-66

Rear combination light bulb replacement ................................................. 9-66

High mounted stop light replacement ....................................................... 9-68

License plate light bulb replacement ......................................................... 9-68

Interior light bulb replacement ................................................................... 9-69

Appearance care...............................................................................................9-70

Exterior care...................................................................................................9-70

Interior care....................................................................................................9-76

9

Emission control system ..................................................................................9-79

1. Crankcase emission control system ........................................................9-79

2. Evaporative emission control system ......................................................9-79

3. Exhaust emission control system............................................................9-80

09

ENGINE COMPARTMENT

Smartstream G1.0

Smart stream G1.0 T-GDi

Smartstream G1.2

The actual engine room in the vehicle may differ from the illustration.

OAC3089001R/OAC3N080001R/OAC3089002R

1. Engine coolant reservoir

2. Engine oil ꢀller cap

3. Brake/clutch* ꢁuid reservoir

4. Air cleaner

6. Battery

7. windscreen washer ꢁuid reservoir

8. Radiator cap

9. Engine oil dipstick

5. Fuse box

* : if equipped

9-3

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care to

prevent damage to your vehicle and in-

jury to yourself whenever performing

any maintenance or inspection proce-

dures.

We recommend you have your vehicle

maintained and repaired by a HYUN-

DAI authorised repairer. A HYUNDAI

authorised repairer meets HYUNDAI’s

high service quality standards and re-

ceives technical support from HYUN-

DAI in order to provide you with a high

level of service satisfaction.

Owner maintenance

precautions

Inadequate, incomplete or insufficient

servicing may result in operational

problems with your vehicle that could

lead to vehicle damage, an accident, or

personal injury. This chapter provides

instructions only for the maintenance

items that are easy to perform.

Your vehicle should not be modified in

any way. Such modifications may ad-

versely affect the performance, safety

or durability of your vehicle and may, in

addition, violate conditions of the limit-

ed warranties covering the vehicle.

Owner’s responsibility

Maintenance service and record reten-

tion are the owner’s responsibility.

NOTICE

You should retain documents that show

proper maintenance has been per-

formed on your vehicle in accordance

with the scheduled maintenance ser-

vice charts shown on the following pag-

es. You need this information to estab-

lish your compliance with the servicing

and maintenance requirements of your

vehicle warranties.

Improper owner maintenance during

the warranty period may affect war-

ranty coverage. For details, read the

separate Warranty Booklet provided

with the vehicle. If you’re unsure

about any servicing or maintenance

procedure, we recommend that the

system be serviced by a HYUNDAI

authorised repairer.

Detailed warranty information is pro-

vided in your Warranty Booklet.

Repairs and adjustments required as a

result of improper maintenance or a

lack of required maintenance are not

covered.

9-4

09

OWNER MAINTENANCE

The following lists are vehicle checks

WARNING

and inspections that should be per-

formed by the owner or a HYUNDAI

authorised repairer at the frequencies

indicated to help ensure safe, depend-

able operation of your vehicle.

Performing maintenance work on a

vehicle can be dangerous. If you

lack sufficient knowledge and expe-

rience or the proper tools and equip-

ment to do the work, we recommend

that the system be serviced by a

HYUNDAI authorised repairer. AL-

WAYS follow these precautions for

performing maintenance work:

Any adverse conditions should be

brought to the attention of your dealer

as soon as possible.

These Owner Maintenance vehicle

checks are generally not covered by

warranties and you may be charged for

labour, parts and lubricants used.

• Park your vehicle on level ground,

move the shift lever into the N

(Neutral, for Automated Manual

Transmission vehicle) position or

1st gear (for Manual transmission

vehicle) position, apply the park-

ing brake, and place the ignition

switch in the LOCK/ OFF position.

Owner maintenance schedule

When you stop for fuel:

• Check the coolant level in the engine

coolant reservoir.

• Block the tyres (front and back) to

prevent the vehicle from moving.

• Check the windscreen washer fluid

level.

Remove loose clothing or jewel-

lery that can become entangled in

moving parts.

• Check for low or under-inflated tyres.

• Check the radiator and condenser.

Check if the front of the radiator and

condenser are clean and not blocked

with leaves, dirt or insects, etc.

If any of the above parts are extreme-

ly dirty or you are not sure of their

condition, we recommend that you

contact a HYUNDAI authorised re-

pairer.

• If you must run the engine during

maintenance, do so in an outdoor

area or in an area with plenty of

ventilation.

• Keep flames, sparks, or smoking

materials away from the battery

and fuel-related parts.

WARNING

Be careful when checking your cool-

ant level if the engine is hot. This

may result in coolant being blown

out of the opening and cause seri-

ous burns and other injuries.

9-5

Maintenance

Whilst operating your vehicle:

At least twice a year:

(for example, every Spring and

Autumn)

• Check radiator, heater and air condi-

tioning hoses for leaks or damage.

• Check windscreen washer spray and

wiper operation. Clean wiper blades

with a clean cloth dampened with

washer fluid.

• Note any changes in the sound of the

exhaust or any smell of exhaust

fumes in the vehicle.

• Check for vibrations in the steering

wheel. Notice if there is any increased

steering effort or looseness in the

steering wheel, or change in its

straight-ahead position.

• Notice if your vehicle constantly turns

slightly or “pulls” to one side when

travelling on smooth, level road.

• Check headlight alignment.

• Check muffler, exhaust pipes, shields

and clamps.

• When stopping, listen and check for

unusual sounds, pulling to one side,

increased brake pedal travel or “hard-

to-push” brake pedal.

• If any slipping or changes in the op-

eration of your transmission occurs,

check the transmission fluid level.

• Check the seat belts for wear and

function.

At least once a year:

• Clean body and door drain holes.

• Lubricate door hinges and bonnet

hinges.

• Check the parking brake.

• Lubricate door and bonnet locks and

• Check for fluid leaks under your ve-

hicle (water dripping from the air con-

ditioning system during or after use is

normal).

latches.

• Lubricate door rubber weather strips.

• Lubricate door checker

• Check the air conditioning system.

At least monthly:

• Check coolant level in the engine

coolant reservoir.

• Inspect and lubricate Automated

manual transmission linkage and

controls.

• Clean the battery and terminals.

• Check the brake fluid level.

• Check the operation of all exterior

lights, including the stoplights, turn

signals and hazard warning flashers.

• Check the inflation pressures of all

tyres including the spare for tyres that

are worn, show uneven wear, or are

damaged.

• Check for loose wheel lug nuts.

9-6

09

SCHEDULED MAINTENANCE SERVICES

Follow Normal Maintenance Schedule if the vehicle is usually operated where none

of the following conditions apply.

If any of the following conditions apply, you must follow the Maintenance Under

Severe Usage Conditions.

• Repeated driving short distance of less than 5 mi. (8 km) in normal temperature

or less than 10 mi. (16 km) in freezing temperature

• Low speed driving for long distances

• Driving on rough, dusty, muddy, unpaved, graveled or salt-spread roads

• Driving in areas using salt or other corrosive materials or in very cold weather

• Driving in heavy dust condition

• Driving in heavy traffic area

• Driving on uphill, downhill, or mountain roads repeatedly

• Towing a trailer or using a camper, or driving with loads on the roof

• Driving as a patrol car, taxi, other commercial use of vehicle towing

• Frequently driving under high speed or rapid acceleration/deceleration

• Frequently driving in stop-and-go conditions

• Engine oil usage which is not recommended

(Mineral type, Semi-synthetic, Lower grade, etc.)

If your vehicle is operated under the above conditions, you should inspect, replace

or refill more frequently than Normal Maintenance Schedule which is provided in

your Service Passport.

Information

i

• As it is normal for engine oil to be consumed during driving, the engine oil level

should be checked on regular basis.

• The engine oil change interval for normal operating conditions is based on the

use of the recommended engine specification. If the recommended engine oil

specification is not used, then replace the engine oil according to the mainte-

nance schedule under severe operating conditions.

9-7

Maintenance

EXPLANATION OF SCHEDULED MAINTENANCE ITEMS

Engine oil and filter

Fuel filter

The engine oil and filter should be

changed at the intervals specified in the

maintenance schedule. If the vehicle is

being driven in severe conditions, more

frequent oil and filter changes are re-

quired.

This petrol powered vehicle is equipped

with a lifetime fuel filter that is integrat-

ed with the fuel tank. Regular mainte-

nance or replacement is not needed;

however, the quality of fuel used may

impact the frequency of maintenance

needed. If there are any fuel related

problems like fuel flow restriction, surg-

ing, loss of power, hard starting prob-

lem etc, fuel filter inspection or replace-

ment may be needed. We recommend

the fuel filter be inspected or replaced

by a HYUNDAI authorised repairer.

Drive belts

Inspect all drive belts for evidence of

cuts, cracks, excessive wear or oil satu-

ration and replace if necessary. Drive

belts should be checked periodically for

proper tension and adjusted as neces-

sary.

Fuel lines, fuel hoses and

connections

Check the fuel lines, fuel hoses and

connections for leakage and damage.

We recommend that the fuel lines, fuel

hoses and connections be replaced by

a HYUNDAI authorised repairer.

CAUTION

When you are inspecting the belt,

place the ignition switch to the lock/

off or ACC position.

Vapour hose and fuel filler cap

The vapour hose and fuel filler cap

should be inspected at those intervals

specified in the maintenance schedule.

Make sure that a new vapour hose or

fuel filler cap is correctly replaced.

9-8

09

Vacuum crankcase ventilation

hoses (if equipped)

WARNING

Do not disconnect and inspect spark

plugs when the engine is hot. You

may burn yourself.

Inspect the surface of hoses for evi-

dence of heat and/or mechanical dam-

age. Hard and brittle rubber, cracking,

tears, cuts, abrasions, and excessive

swelling indicate deterioration. Particu-

lar attention should be paid to examine

those hose surfaces nearest to high

heat sources, such as the exhaust

manifold.

Cooling system

Check the cooling system parts, such

as radiator, coolant reservoir, hoses

and connections for leakage and dam-

age. Replace any damaged parts.

Inspect the hose routing to assure that

the hoses do not come in contact with

any heat source, sharp edges or mov-

ing component which might cause heat

damage or mechanical wear. Inspect

all hose connections, such as clamps

and couplings, to make sure they are

secure, and that no leaks are present.

Hoses should be replaced immediately

if there is any evidence of deterioration

or damage.

Engine coolant

The coolant should be changed at the

intervals specified in the maintenance

schedule.

Manual transmission fluid

(if equipped)

Inspect the manual transmission fluid

according to the maintenance sched-

ule.

Air cleaner filter

We recommend that the air cleaner fil-

ter be replaced by a HYUNDAI autho-

rised repairer.

Automated manual

transmission fluid (if equipped)

Inspect the Automated manual trans-

mission fluid according to the mainte-

nance schedule.

Spark plugs

(for petrol engine)

Make sure to install new spark plugs of

the correct heat range.

NOTICE

When assembling parts, be sure to

wipe out foreign substances inside and

outside of the boot bottom of the igni-

tion coil and the insulator of the spark

plug with a soft cloth to prevent con-

tamination of the spark plug insulator.

The use of non-specified fluid (even

marked as compatible with genuine)

could result in shift quality deterio-

ration and vibrations, eventually, the

transmission failure.

Use only specified Automated man-

ual transmission fluid. (Refer to

“Recommended lubricants and ca-

pacities” in chapter 2.)

9-9

Maintenance

Brake hoses and lines

Suspension mounting bolts

Visually check for proper installation,

chafing, cracks, deterioration and any

leakage. Replace any deteriorated or

damaged parts immediately.

Check the suspension connections for

looseness or damage. Retighten to the

specified torque.

Steering gear box, linkage &

boots/lower arm ball joint

With the vehicle stopped and engine

off, check for excessive free-play in the

steering wheel.

Check the linkage for bends or dam-

age. Check the dust boots and ball

joints for deterioration, cracks, or dam-

age. Replace any damaged parts.

Brake/clutch fluid (if equipped)

Check brake/clutch fluid level in the

brake fluid reservoir. The level should

be between “MIN” (Minimum) and

“MAX” (Maximum) marks on the side of

the reservoir. Use only hydraulic brake/

clutch fluid conforming to DOT4 specifi-

cation.

Parking brake

Drive shafts and boots

Inspect the parking brake system in-

cluding the parking brake lever and ca-

bles.

Check the drive shafts, boots and

clamps for cracks, deterioration, or

damage. Replace any damaged parts

and, if necessary, repack the grease.

Rear brake drums and linings

(if equipped)

Check the rear brake drums and linings

for scoring, burning, leaking fluid, bro-

ken parts, and excessive wear.

Air conditioning refrigerant/

compressor

Check the air conditioning lines and

connections for leakage and damage.

Brake pads, calipers and rotors

Check the pads for excessive wear,

discs for run out and wear, and calipers

for fluid leakage.

For more information on checking the

pads or lining wear limit, refer to the

HYUNDAI web site.

(http://service.hyundai-motor.com)

9-10

09

ENGINE OIL

Checking the engine oil level

WARNING

Engine oil is used for lubricating, cool-

ing, and operating various hydraulic

components in the engine. Engine oil

consumption whilst driving is normal,

and it is necessary to check and refill

the engine oil regularly. Also, check

and refill the oil level within the recom-

mended maintenance schedule to pre-

vent deterioration of oil performance.

Radiator hose

Be very careful not to touch the ra-

diator hose when checking or add-

ing the engine oil as it may be hot

enough to burn you.

NOTICE

• Do not overfill the engine oil. It

may damage the engine.

Check the engine oil following the be-

low procedure.

• Do not spill engine oil, when add-

ing or changing engine oil. If you

drop the engine oil on the engine

room, wipe it off immediately.

• When you wipe the oil level gauge,

you should wipe it with a clean

cloth. When mixed with debris, it

can cause engine damage.

OAC3089003TU

1. Follow all of the oil manufacturer’s

precautions.

2. Be sure the vehicle is on the level

ground in P (Park) with the parking

brake set and the wheels blocked.

3. Turn the engine on and warm the en-

gine up until the coolant temperature

reaches a constant normal tempera-

ture.

4. Turn the engine off, remove the oil

filler cap and pull the dipstick out.

Wait for 15 minutes for the oil to re-

turn to the oil pan.

5. Wipe the dipstick clean and re-insert

it fully.

6. Pull the dipstick out again and check

the level. The level should be be-

tween F (Full) and L (Low).

9-11

Maintenance

Checking the engine oil and

filter

OAC3089004TU

7. If the oil level is near or below the L,

add enough oil to bring the level to F.

Use a funnel to help prevent oil from

being spilled on engine components.

Use only the specified engine oil. (Re-

fer to “Recommended lubricants and

capacities” in chapter 2.)

• We recommend that the engine oil

and filter be replaced by

HYUNDAI authorised repairer.

a

• If the maintenance schedule to re-

place engine oil is exceeded, the

engine oil performance may dete-

riorate, and the engine condition

may be affected. Therefore, re-

place the engine oil according to

the maintenance schedule.

• To keep the engine in optimal con-

dition, use the recommended en-

gine oil and filter. If the recom-

mended engine oil and filter are

not used, replace it according to

the maintenance schedule under

severe usage conditions.

• The purpose of the maintenance

schedule for engine oil replace-

ment is to prevent oil deterioration

and it is irrelevant to oil consump-

tion. Check and refill engine oil

regularly.

NOTICE

To prevent damage to your engine:

• Do not spill engine oil when add-

ing or changing engine oil. Wipe

off spilled oil immediately.

• The engine oil consumption may

increase whilst you break in a new

vehicle and it will be stabilized af-

ter driving 4,000 miles (6,000 km).

• The engine oil consumption can

be affected by driving habits, cli-

mate conditions, traffic conditions,

oil quality, etc. Therefore, it is rec-

ommended that you inspect the

engine oil level regularly and refill

it if necessary.

9-12

09

NOTICE

Information

i

Never add any additives to the en-

gine oil. Engine oil additives can

change the properties of engine oil

and may cause serious engine fail-

ure.

When the oil pressure is low due to in-

sufficient engine oil, the Engine Oil

Pressure (

) warning light will il-

luminate. In addition, the enhanced

engine protection system, which limits

the engine’s power is activated and the

Malfunction Indicator Light (

) will

illuminate when the vehicle is driven in

this state continuously. When oil pres-

sure is restored, the Engine Oil

Pressure warning light will turn off

and the engine power will no longer be

limited.

CAUTION

The engine oil is very hot immedi-

ately after the vehicle has been driv-

en and can cause burns during re-

placement. Replace the engine oil

after the engine oil has cooled down.

WARNING

Used engine oil may cause irrita-

tion or cancer of the skin if left in

contact with the skin for prolonged

periods of time. Used engine oil

contains chemicals that have

caused cancer in laboratory ani-

mals. Always protect your skin by

washing your hands thoroughly

with soap and warm water as soon

as possible after handling used oil.

9-13

Maintenance

ENGINE COOLANT

The high-pressure cooling system has

a reservoir filled with year-round anti-

freeze coolant. The reservoir is filled at

the factory.

Checking the coolant level

Check the antifreeze protection and

coolant concentration level at least

once a year, at the beginning of the

winter season, and before travelling to

a colder climate.

NOTICE

OAC3089005TU

• When the engine overheats from

low engine coolant, suddenly add-

ing engine coolant may cause

cracks in the engine. To prevent

damage, add engine coolant slow-

ly in small quantities.

Check the condition and connections of

all cooling system hoses and heater

hoses. Replace any swollen or deterio-

rated hoses.

The coolant level should be filled be-

tween F (Full) and L (Low) marked on

the side of the coolant reservoir when

the engine is cool.

• Do not drive with no engine cool-

ant. It may cause water pump fail-

ure and engine seizure, etc.

If the coolant level is low, add enough

distilled (deionized) water.

Bring the level to F (Full), but do not

overfill. If frequent additions are re-

quired, we recommend that the system

be inspected by a HYUNDAI authorised

repairer.

9-14

09

Recommended engine coolant

• When adding coolant, use only dis-

tilled (deionized) water for your vehi-

cle and never mix hard water in the

coolant filled at the factory. An incor-

rect coolant mixture can result in seri-

ous malfunction or engine damage.

• The engine in your vehicle has alu-

minium engine parts and must be

protected by an phosphate based

ethylene-glycol coolant to prevent

corrosion and freezing.

• DO NOT USE alcohol or methanol

coolant or mix them with the specified

coolant.

• Do not use a solution that contains

more than 60% antifreeze or less

than 35% antifreeze, which would re-

duce the effectiveness of the solu-

tion.

OAC3089006TU

WARNING

Never remove the radiator

cap or the drain plug

whilst the engine and ra-

diator are hot. Hot coolant

and steam may blow out

under pressure, causing serious in-

jury.

Turn the engine off and wait until the

engine cools down. Use extreme

care when removing the radiator

cap. Wrap a thick towel around it,

and turn it counterclockwise slowly

to the first stop. Step back whilst the

pressure is released from the cool-

ing system. When you are sure all

the pressure has been released,

press down on the cap, using a thick

towel, and continue turning counter-

clockwise to remove it.

For mixture percentage, refer to the fol-

lowing table.

Mixture Percentage

(volume)

Ambient

Temperature

Antifreeze

Water

65

35

40

50

60

-15°C (5°F)

-25°C (-13°F)

-35°C (-31°F)

-45°C (-49°F)

60

50

40

WARNING

Information

i

The electric motor for the

cooling fan may continue

to operate or start up

when the engine is not

running and can cause

serious injury.

If in doubt about the mix ratio, a 50%

water and 50% antifreeze mix is the

easiest to mix together as it will be the

same quantity of each. It is suitable to

use for most temperature ranges of

-35°C (-31°F) and higher.

Keep hands, clothing and tools away

from the rotating fan blades of the

cooling fan.

9-15

Maintenance

Changing the engine coolant

We recommend that the coolant be re-

placed by a HYUNDAI authorised re-

pairer.

NOTICE

Put a thick cloth or fabric around the

radiator cap before refilling the cool-

ant in order to prevent the coolant

from overflowing into engine parts

such as alternator.

WARNING

Do not use engine coolant or anti-

freeze in the washer fluid reservoir.

Engine coolant can severely ob-

scure visibility when sprayed on the

windscreen and may cause loss of

vehicle control or damage to paint

and body trim.

9-16

09

BRAKE/CLUTCH FLUID (IF EQUIPPED)

Checking the brake/clutch fluid

level

Information

i

Use only the specified brake/clutch

fluid. Refer to “Recommended lubri-

cants and capacities” in chapter 2.

Information

i

Before removing the brake/clutch filler

cap, read the warning on the cap.

Information

i

OAC3089007R

Clean the filler cap before removing.

Use only DOT4 brake/clutch fluid

from a sealed container.

Check the fluid level in the reservoir pe-

riodically. The fluid level should be be-

tween MAX and MIN marks on the side

of the reservoir.

Before removing the reservoir cap and

adding brake/clutch fluid, clean the

area around the reservoir cap thor-

oughly to prevent brake/clutch fluid

contamination.

If the level is low, add fluid to the MAX

level. The level will fall with accumulat-

ed mileage. This is a normal condition

associated with the wear of the brake

linings.

WARNING

If the brake/clutch system requires

frequent additions of fluid this could

indicate a leak in the brake/clutch

system. We recommend that the ve-

hicle be inspected by a HYUNDAI au-

thorised repairer.

If the fluid level is excessively low,

we recommend that the system be

checked by a HYUNDAI authorised re-

pairer.

9-17

Maintenance

WARNING

Do not let brake/clutch fluid enter

into your eyes. If brake/clutch fluid

gets in your eyes, flush your eyes

with clean water for at least 15 min-

utes and get immediate medical at-

tention.

NOTICE

• Do not allow brake/clutch fluid to

contact the vehicle’s body paint,

as it will result in paint damage.

• NEVER use brake/clutch fluid

which has been exposed to open

air for an extended time, as its

quality cannot be guaranteed. It

should be disposed of properly.

• Don’t put in the wrong type of flu-

id. A few drops of mineral-based

oil, such as engine oil in your

brake/clutch system can damage

system parts.

9-18

09

WASHER FLUID

Checking the washer fluid level

PARKING BRAKE

Checking the parking brake

OAC3089008TU

OAC3069002R

Check the fluid level in the washer fluid

reservoir and add fluid if necessary.

Plain water may be used if washer fluid

is not available.

Check the stroke of the parking brake

by counting the number of “clicks’’

heard whilst fully applying it from the re-

leased position.

Also, the parking brake alone should

securely hold the vehicle on a fairly

steep grade. If the stroke is more or

less than specified, we recommend that

the system be inspected by a HYUN-

DAI authorised repairer.

However, use washer solvent with anti-

freeze characteristics in cold climates

to prevent freezing.

WARNING

To prevent serious injury or death,

take the following safety precau-

tions when using washer fluid:

Stroke : 5-7 “clicks’’ at a force of 20

kg (44 lbs, 196 N).

• Do not use engine coolant or anti-

freeze in the washer fluid reser-

voir. Engine coolant can severely

obscure visibility when sprayed on

the windscreen and may cause

loss of vehicle control resulting in

an accident or damage to paint

and body trim.

• Do not allow sparks or flames to

contact the washer fluid or the

washer fluid reservoir. Washer flu-

id may contain alcohol and can be

flammable.

• Do not drink washer fluid and

avoid contact with skin. Washer

fluid is poisonous to humans and

animals.

• Keep washer fluid away from chil-

dren and animals.

9-19

Maintenance

AIR CLEANER

Filter replacement

Type A

2. Remove the used filter and wipe the

inside of the air cleaner housing to

remove dust in cover housing.

3. Replace the new filter with clean

hands and ensure the rubber gasket

is not taken off.

4. Reassemble in the reverse order of

removal.

OAC3089009TU

The air cleaner filter can be cleaned for

inspection using compressed air.

Do not attempt to wash or to rinse it, as

water will damage the filter.

If soiled, the air cleaner filter must be

replaced.

OAC3089050TU

5. The protrusions in the filter should

be mounted either on the left or right

side of the air cleaner upper side. If

incorrectly installed to the bottom

side, it may be difficult to assemble.

OAC3089010TU

OAC3089011TU

1. Remove the cleaner cover by open-

ing the clips.

9-20

09

Type B

OAC3N080055TU

OAC3N080053TU

2. Open the air cleaner filter cover by

lifting the lock(2) in the direction of

the arrow.

The air cleaner filter can be cleaned for

inspection using compressed air. Do

not attempt to wash or to rinse it, as wa-

ter will damage the filter. If soiled, the

air cleaner filter must be replaced.

OAC3N080056TU

3. Pull down the lever to the “UNLOCK”

position.

OAC3N080054TU

4. Remove the used filter and wipe the

inside of the air cleaner housing to

remove dust in cover housing.

1. Push the open button in the direction

of the arrow (1).

5. Replace the new filter with clean

hands and ensure the rubber gasket

is not taken off.

9-21

Maintenance

CLIMATE CONTROL AIR

FILTER

Information

i

Filter inspection

If the vehicle is operated in extremely

dusty or sandy areas, replace the ele-

ment more often than the usual recom-

mended intervals.

The climate control air filter should be

replaced according to the Maintenance

Schedule. If the vehicle is operated in

severely air-polluted cities or on dusty

rough roads for a long period, it should

be inspected more frequently and re-

placed earlier. When you replace the

climate control air filter, replace it per-

forming the following procedure, and be

careful to avoid damaging other com-

ponents.

NOTICE

• Do not drive with the air cleaner fil-

ter removed. This will result in ex-

cessive engine wear.

• When removing the air cleaner fil-

ter, be careful that dust or dirt does

not enter the air intake, or damage

may result.

Replace the filter according to the Main-

tenance Schedule.

• Use HYUNDAI genuine parts or the

equivalent speficied for your vehi-

cle. Use of parts without the match-

ing quality could damage the en-

gine.

Filter replacement

OAC3059042R

1. Open the glove box.

9-22

09

OAC3089012R

ODH073012

2. Push in both sides of the glove box

as shown. This will ensure that the

glove box stopper pins will get re-

leased from its holding location al-

lowing the glove box to hang.

4. Replace the climate control air filter.

5. Reassemble in the reverse order of

disassembly.

NOTICE

Install a new climate control air filter

in the correct direction with the ar-

row symbol () facing downwards,

otherwise, it may be noisy and the

effectiveness of the filter may be re-

duced.

OAH2078021

3. Remove the climate control air filter

cover.

9-23

Maintenance

WIPER BLADES

Blade inspection

Blade replacement

Contamination of either the windscreen

or the wiper blades with foreign matter

can reduce the effectiveness of the

windscreen wipers.

When the wipers no longer clean ade-

quately, the blades may be worn or

cracked, and require replacement.

Common sources of contamination are

insects, tree sap, and hot wax treat-

ments used by some commercial car

washes. If the blades are not wiping

properly, clean both the window and

the blades with a good cleaner or mild

detergent, and rinse thoroughly with

clean water.

CAUTION

Do not allow the wiper arm to fall

against the windscreen, since it may

chip or crack the windscreen.

Front windscreen wiper blade

NOTICE

To prevent damage to the wiper

blades, arms or other components,

do not:

• Use petrol, kerosene, paint thin-

ner, or other solvents on or near

them.

• Attempt to move the wipers manu-

ally.

• Use non-specified wiper blades.

OGSR076067

Information

i

Commercial hot waxes applied by au-

tomatic car washes have been known

to make the windscreen difficult to

clean.

Information

i

OGSR076066

1. Lift up the wiper blade clip. Then lift

up the wiper blade.

2. Whilst pushing the lock (1), pull down

the wiper blade (2).

Wiper blades are consumable item.

Normal wear of the wipers may not be

covered by your vehicle warranty.

9-24

09

Rear window wiper blade

(if equipped)

OGSR076068

3. Remove the wiper blade from the

wiper arm.

OLMB073023

4. Install a new wiper blade assembly

in the reverse order of removal.

1. Raise the wiper arm and rotate the

wiper blade assembly (1).

2. Pull out the wiper blade assembly.

5. Return the wiper arm on the wind-

screen.

OLMB073024

3. Install the new blade assembly by

inserting the centre part into the slot

in the wiper arm until it clicks into

place.

4. Make sure the blade assembly is in-

stalled firmly by trying to pull it slight-

ly.

To prevent damage to the wiper arms

or other components, we recommend

that the wiper blade be replaced by a

HYUNDAI authorised repairer.

9-25

Maintenance

BATTERY

For best battery service

The electrolyte level should be between

LOWER (MIN) and UPPER (MAX).

When the electrolyte level is low, add

distilled (or de-mineralized) water.

(Never add sulfuric acids or other elec-

trolyte).

Be careful not to spill distilled (or de-

mineralized) water over the battery

surface or other adjacent components.

Also, do not overfill the battery cells.

If not, it may corrode the battery or

other components. Finally, securely

close the cell cap. However, we recom-

mend you to contact a HYUNDAI au-

thorised repairer for better battery

service.

OAC3089013TU

• Keep the battery securely mounted.

• Keep the battery top clean and dry.

• Keep the terminals and connections

clean, tight, and coated with petro-

leum jelly or terminal grease.

WARNING

• Rinse any spilled electrolyte from the

battery immediately with a solution of

water and baking soda.

• If the vehicle is not going to be used

for an extended time, disconnect the

battery cables.

To prevent SERIOUS INJURY or

DEATH to you or bystanders, always

follow these precautions when work-

ing near or handling the battery:

Always read and follow

instructions carefully

when handling a battery.

Information

- For batteries marked with

UPPER and LOWER

i

Wear eye protection de-

signed to protect the eyes

from acid splashes.

Keep all flames, sparks,

or smoking materials

away from the battery.

Hydrogen is always pres-

ent in battery cells, is

highly combustible, and

may explode if ignited.

OHYK077011

If your vehicle is equipped with a bat-

tery marked with LOWER (MIN) and

UPPER (MAX) on the side, you should

check the electrolyte level.

9-26

09

• The battery may rupture or ex-

plode when you jump start with a

low or frozen battery.

Batteries contain sulfuric

acid which is highly cor-

rosive. Do not allow acid

to contact your eyes, skin

or clothing.

• Leaked battery electrolyte due to

repeated driving on sharp curves

(for example, on circuits) may

cause safety problem. Avoid re-

peated driving on sharp curves.

If acid gets into your eyes, flush your

eyes with clean water for at least 15

minutes and get immediate medical

attention. If acid gets on your skin,

thoroughly wash the area. If you feel

pain or a burning sensation, get

medical attention immediately.

NOTICE

Always follow these instructions

when handling your vehicle’s bat-

tery to prevent damage to your bat-

tery:

• When lifting a plastic-cased bat-

tery, excessive pressure on the

case may cause battery acid to

leak. Lift with a battery carrier or

with your hands on opposite cor-

ners.

• When you do not use the vehicle

for a long time in a low tempera-

ture area, disconnect the battery

and keep it indoors.

• Do not attempt to jump start your

vehicle if your battery is frozen.

• Always charge the battery fully to

prevent battery case damage in

low temperature areas.

• NEVER attempt to recharge the

battery when the vehicle’s battery

cables are connected to the bat-

tery.

• Prevent liquid from wetting the

battery terminals. The perfor-

mance of the battery may be de-

graded, and may cause injury. Be

cautious when loading liquid in the

boot.

• The electrical ignition system

works with high voltage. NEVER

touch these components with the

engine running or when the igni-

tion switch is in the ON position.

• Do not tilt the battery.

• If you connect unauthorised elec-

tronic devices to the battery, the

battery may be discharged. Never

use unauthorised devices.

• Do not allow the (+) and (-) jumper

cables to touch. It may cause

sparks.

9-27

Maintenance

Battery capacity label

WARNING

Example

When recharging the battery, ob-

serve the following precautions:

• Before performing maintenance or

recharging the battery, turn off all

accessories and stop the engine.

• Do not allow cigarettes, sparks, or

flame near the battery.

• Wear eye protection when check-

ing the battery during charging.

• The battery must be removed from

the vehicle and placed in an area

with good ventilation.

OAC3089014TU

h The actual battery label in the vehicle

• Watch the battery during charging,

and stop or reduce the charging

rate if the battery cells begin gas-

sing (boiling) violently or if the

temperature of the electrolyte of

any cell exceeds 49°C (120°F).

may differ from the illustration.

1. AGM50L-DIN : The HYUNDAI mod-

el name of battery

2. 12V : The nominal voltage

3. 50Ah (20HR) : The nominal capacity

(in Ampere hours)

• The negative battery cable must be

removed first and installed last

when the battery is disconnected.

4. RC 80 : The nominal reserve capac-

ity (in min.)

• Disconnect the battery charger in

the following order.

5. CCA 560A : Cold-test current in am-

peres by SAE/EN

1. Turn off the battery charger

main switch.

2. Unhook the negative clamp

from the negative battery termi-

nal.

Battery recharging

Your vehicle has a maintenance-free,

calcium-based battery.

• If the battery becomes discharged

over a short time (because, for ex-

ample, the headlights or interior lights

were left on whilst the vehicle was not

in use), recharge it by slow charging

(trickle) for 10 hours.

3. Unhook the positive clamp from

the positive battery terminal.

• If the battery gradually discharges

because of high electrical load whilst

the vehicle is being used, recharge it

at 20-30A for two hours.

9-28

09

By jump starting

NOTICE

After a jump start from a good battery,

drive the vehicle for at least 30 minutes

or operate at idle for at least 60 minutes

before it is shutoff. The vehicle may not

restart if you shut it off before the bat-

tery had a chance to adequately re-

charge. See “Jump Starting” in chapter

8 for more details on jump starting pro-

cedures.

AGM battery (if equipped)

• Absorbent Glass Mat (AGM) bat-

teries are maintenance-free and

we recommend that the AGM bat-

tery be serviced by a HYUNDAI au-

thorised repairer. For charging

your AGM battery, use only fully

automatic battery chargers that

are specially developed for AGM

batteries.

Information

i

• When replacing the AGM battery,

we recommend that you use parts

for replacement from a HYUNDAI

authorised repairer.

An inappropriately dis-

posed battery can be harm-

ful to the environment and

human health. Dispose of

the battery according to

your local law(s) or regula-

tion.

• Do not open or remove the cap on

top of the battery. This may cause

leaks of internal electrolyte that

could result in severe injury.

Reset items

Items should be reset after the battery

has been discharged or the battery has

been disconnected.

• Auto up/down window

(See chapter 5)

• Trip computer (See chapter 4)

• Climate control system

(See chapter 5)

9-29

Maintenance

TYRES AND WHEELS

Tyre care

WARNING

For proper maintenance, safety, and

maximum fuel economy, you must al-

ways maintain recommended tyre infla-

tion pressures and stay within the load

limits and weight distribution recom-

mended for your vehicle.

Tyre failure may cause loss of vehi-

cle control resulting in an accident.

To reduce risk of SERIOUS INJURY

or DEATH, take the following pre-

cautions:

• Inspect your tyres monthly for

proper inflation as well as wear

and damage.

• The recommended cold tyre pres-

sure for your vehicle can be found

in this manual and on the tyre label

located on the driver’s side centre

pillar. Always use a tyre pressure

gauge to measure tyre pressure.

Tyres with too much or too little

pressure wear unevenly causing

poor handling.

OAC3019023TU

• Check the pressure of the spare

every time you check the pressure

of the other tyres on your vehicle.

All specifications (sizes and pressures)

can be found on a label attached to the

left side centre pillar.

• Replace tyres that are worn, show

uneven wear, or are damaged.

Worn tyres can cause loss of brak-

ing effectiveness, steering control,

or traction.

• ALWAYS replace tyres with the

same size as each tyre that was

originally supplied with this vehi-

cle. Using tyres and wheels other

than the recommended sizes could

cause unusual handling character-

istics, poor vehicle control, or neg-

atively affect your vehicle’s Anti-

Lock Brake System (ABS) resulting

in a serious accident.

9-30

09

Recommended cold tyre

inflation pressures

NOTICE

• Under-inflation results in exces-

sive wear, poor handling and re-

duced fuel economy. Wheel defor-

mation is also possible. Keep your

tyre pressures at the proper levels.

If a tyre frequently needs refilling,

we recommend it be checked by a

HYUNDAI authorised repairer.

All tyre pressures (including the spare)

should be checked when the tyres are

cold. “Cold tyres” means the vehicle

has not been driven for at least three

hours or has been driven for less than 1

mile (1.6 km).

Warm tyres normally exceed recom-

mended cold tyre pressures by 28 to 41

kPa (4 to 6 psi). Do not release air from

warm tyres to adjust the pressure or the

tyres will be under-inflated. For recom-

mended inflation pressure, refer to

“Tyre and Wheels” in chapter 8.

• Over-inflation produces a harsh

ride, excessive wear at the centre

of the tyre tread, and a greater pos-

sibility of damage from road haz-

ards.

Check tyre inflation pressure

Check your tyres, including the spare

tyre, once a month or more.

WARNING

Recommended pressures must be

maintained for the best ride, vehicle

handling, and minimum tyre wear.

How to check

Over-inflation or under-inflation can

reduce tyre life, adversely affect ve-

hicle handling, and lead to sudden

tyre failure that could result in loss

of vehicle control resulting in an ac-

cident.

Use a good quality tyre pressure gauge

to check tyre pressure. You can not tell

if your tyres are properly inflated simply

by looking at them. Radial tyres may

look properly inflated when they are

under-inflated.

Severe under-inflation can lead to

severe heat build-up, causing blow-

outs, tread separation and other tyre

failures that can result in the loss of

vehicle control resulting in an acci-

dent. This risk is much higher on hot

days and when driving for long peri-

ods at high speeds.

Remove the valve cap from the tyre

valve stem. Press the tyre gauge firmly

onto the valve to get a pressure mea-

surement. If the cold tyre inflation pres-

sure matches the recommended pres-

sure on the tyre and loading information

label, no further adjustment is neces-

sary. If the pressure is low, add air until

you reach the recommended pressure.

Make sure to put the valve caps back

on the valve stems. Without the valve

cap, dirt or moisture could get into the

valve core and cause air leakage. If a

valve cap is missing, install a new one

as soon as possible.

9-31

Maintenance

With a full-size spare tyre (if equipped)

If you overfill the tyre, release air by

pushing on the metal stem in the centre

of the tyre valve. Recheck the tyre pres-

sure with the tyre gauge. Be sure to put

the valve caps back on the valve stems.

Without the valve cap, dirt or moisture

could get into the valve core and cause

air leakage. If a valve cap is missing,

install a new one as soon as possible.

CBGQ0706

CBGQ0707

CBGQ0707A

Tyre rotation

Without a spare tyre

To equalize tread wear, HYUNDAI rec-

ommends that the tires be rotated ac-

cording to the maintenance schedule or

sooner if irregular wear develops.

During rotation, check the tyres for cor-

rect balance.

When rotating tyres, check for uneven

wear and damage. Abnormal wear is

usually caused by incorrect tyre pres-

sure, improper wheel alignment, out-of-

balance wheels, severe braking or se-

vere cornering. Look for bumps or

bulges in the tread or side of the tyre.

Replace the tyre if you find any of these

conditions. Replace the tyre if fabric or

cord is visible. After rotation, be sure to

bring the front and rear tyre pressures

to specification and check lug nut tight-

ness (proper torque is 11-13 kgf·m [79-

94 lbf·ft]).

Directional tyres (if equipped)

Disc brake pads should be inspected

for wear whenever tyres are rotated.

9-32

09

Information

i

NOTICE

Incorrect wheel weights can damage

your vehicle’s aluminium wheels.

Use only approved wheel weights.

The outside and inside of the unsym-

metrical tyre is distinguishable. When

installing an unsymmetrical tyre, be

sure to install the side marked “out-

side” face the outside. If the side

marked “inside” is installed on the out-

side, it will have a negative effect on

vehicle performance.

Tyre replacement

Tread wear indicator

WARNING

• Do not use the compact spare tyre

for tyre rotation.

• Do not mix bias ply and radial ply

tyres under any circumstances.

This may cause unusual handling

characteristics that may cause

loss of vehicle control resulting in

an accident.

OLMB073027

If the tyre is worn evenly, a tread wear

indicator will appear as a solid band ac-

ros s the tread. This shows there is less

than 1/16 in. (1.6 mm) of tread left on

the tyre. Replace the tyre when this

happens.

Wheel alignment and tyre

balance

Do not wait for the band to appear

across the entire tread before replacing

the tyre.

The wheels on your vehicle were

aligned and balanced carefully at the

factory to give you the longest tyre life

and best overall performance.

In most cases, you will not need to have

your wheels aligned again. However, if

you notice unusual tyre wear or your

vehicle pulling one way or the other, the

alignment may need to be reset.

If you notice your vehicle vibrating

when driving on a smooth road, your

wheels may need to be rebalanced.

9-33

Maintenance

Compact spare tyre replacement

(if equipped)

WARNING

To reduce the risk of DEATH or SE-

RIOUS INJURY:

A compact spare tyre has a shorter

tread life than a regular size tyre. Re-

place it when you can see the tread

wear indicator bars on the tyre. The re-

placement compact spare tyre should

be the same size and design tyre as the

one provided with your new vehicle and

should be mounted on the same com-

pact spare tyre wheel. The compact

spare tyre is not designed to be mount-

ed on a regular size wheel, and the

compact spare tyre wheel is not de-

signed for mounting a regular size tyre.

• Replace tyres that are worn, show

uneven wear, or are damaged.

Worn tyres can cause loss of brak-

ing effectiveness, steering control,

and traction.

• Always replace tyres with the

same size as each tyre that was

originally supplied with this vehi-

cle. Using tyres and wheels other

than the recommended sizes could

cause unusual handling character-

istics, poor vehicle control, or neg-

atively affect your vehicle’s Anti-

Lock Brake System (ABS) resulting

in a serious accident.

WARNING

The original tyre should be repaired

or replaced as soon as possible to

avoid failure of the spare and loss of

vehicle control resulting in an acci-

dent. The compact spare tyre is for

emergency use only. Do not operate

your vehicle over 50 mph (80 km/h)

when using the compact spare tyre.

• When replacing tyres (or wheels),

it is recommended to replace the

two front or two rear tyres (or

wheels) as a pair. Replacing just

one tyre can seriously affect your

vehicle’s handling.

• Tyres degrade over time, even

when they are not being used. Re-

gardless of the remaining tread,

HYUNDAI recommends that tyres

be replaced after six (6) years of

normal service.

• Heat caused by hot climates or fre-

quent high loading conditions can

accelerate the aging process. Fail-

ure to follow this warning may

cause sudden tyre failure, which

could lead to a loss of vehicle con-

trol resulting in an accident.

9-34

09

1

Wheel replacement

When replacing the metal wheels for

any reason, make sure the new wheels

are equivalent to the original factory

units in diameter, rim width and offset.

5,6

7

4

3

2

Tyre traction

Tyre traction can be reduced if you

drive on worn tyres, tyres that are im-

properly inflated or on slippery road

surfaces. Tyres should be replaced

when tread wear indicators appear. To

reduce the possibility of losing control,

slow down whenever there is rain, snow

or ice on the road.

1

OLMB073028

1. Manufacturer or brand name

Manufacturer or brand name is shown.

2. Tyre size designation

A tyre’s sidewall is marked with a tyre

size designation. You will need this in-

formation when selecting replacement

tyres for your vehicle. The following ex-

plains what the letters and numbers in

the tyre size designation mean.

Tyre maintenance

In addition to proper inflation, correct

wheel alignment helps to decrease tyre

wear. If you find a tyre is worn uneven-

ly, have a authorised repairer check the

wheel alignment.

Example tyre size designation:

When you have new tyres installed,

make sure they are balanced. This will

increase vehicle ride comfort and tyre

life. Additionally, a tyre should always

be rebalanced if it is removed from the

wheel.

(These numbers are provided as an ex-

ample only; your tyre size designator

could vary depending on your vehicle.)

175/65R14 86T

175 - Tyre width in millimeters.

65 - Aspect ratio. The tyre’s section

height as a percentage of its width.

R - Tyre construction code (Radial).

14 - Rim diameter in inches.

86 - Load Index, a numerical code as-

sociated with the maximum load

the tyre can carry.

T - Speed Rating Symbol. See the

speed rating chart in this section for

additional information.

Tyre sidewall labelling

This information identifies and de-

scribes the fundamental characteristics

of the tyre and also provides the tyre

identification number (TIN) for safety

standard certification. The TIN can be

used to identify the tyre in case of a re-

call.

9-35

Maintenance

Wheel size designation

3. Checking tyre life (TIN : Tyre

Identification Number)

Wheels are also marked with important

information that you need if you ever

have to replace one. The following ex-

plains what the letters and numbers in

the wheel size designation mean.

Any tyres that are over six years old,

based on the manufacturing date, (in-

cluding the spare tyre) should be re-

placed by new ones. You can find the

manufacturing date on the tyre sidewall

(possibly on the inside of the wheel),

displaying the DOT Code. The DOT

Code is a series of numbers on a tyre

consisting of numbers and English let-

ters. The manufacturing date is desig-

nated by the last four digits (characters)

of the DOT code.

Example wheel size designation:

5.5J X 14

5.5 - Rim width in inches.

J - Rim contour designation.

14 - Rim diameter in inches.

Tyre speed ratings

DOT : XXXX XXXX OOOO

The chart below lists many of the differ-

ent speed ratings currently being used

for passenger vehicle tyres. The speed

rating is part of the tyre size designation

on the sidewall of the tyre. This symbol

corresponds to that tyre’s designed

maximum safe operating speed.

The front part of the DOT shows

a

plant code number, tyre size and tread

pattern and the last four numbers indi-

cate week and year manufactured.

For example:

DOT XXXX XXXX 1523 represents that

the tyre was produced in the 15th week

of 2023.

Speed Rating

Maximum Speed

Symbol

112 mph (180 km/h)

S

T

4. Tyre ply composition and

material

118 mph (190 km/h)

H

V

130 mph (210 km/h)

149 mph (240 km/h)

168 mph (270 km/h)

186 mph (300 km/h)

The number of layers or plies of rubber-

coated fabric in the tyre. Tyre manufac-

turers also must indicate the materials

in the tyre, which include steel, nylon,

polyester, and others. The letter “R”

means radial ply construction; the letter

“D“ means diagonal or bias ply con-

struction; and the letter “B” means belt-

ed-bias ply construction.

W

Y

9-36

09

The relative performance of tyres de-

5. Maximum permissible

inflation pressure

pends upon the actual conditions of

their use, however, and may depart sig-

nificantly from the norm due to varia-

tions in driving habits, service practices

and differences in road characteristics

and climate.

This number is the greatest amount of

air pressure that should be put in the

tyre. Do not exceed the maximum per-

missible inflation pressure. Refer to the

Tyre and Loading Information label for

recommended inflation pressure.

These grades are molded on the side-

walls of passenger vehicle tyres. The

tyres available as standard or optional

equipment on your vehicle may vary

with respect to grade.

6. Maximum load rating

This number indicates the maximum

load in kilograms and pounds that can

be carried by the tyre. When replacing

the tyres on the vehicle, always use a

tyre that has the same load rating as

the factory installed tyre.

Traction - AA, A, B & C

The traction grades, from highest to

lowest, are AA, A, B and C. Those

grades represent the tyre’s ability to

stop on wet pavement as measured un-

der controlled conditions on specified

government test surfaces of asphalt

and concrete. A tyre marked C may

have poor traction performance.

7. Uniform tyre quality grading

Quality grades can be found where ap-

plicable on the tyre sidewall between

tread shoulder and maximum section

width.

For example:

WARNING

TREADWEAR 200

TRACTION AA

TEMPERATURE A

The traction grade assigned to this

tyre is based on straight-ahead

braking traction tests, and does not

include acceleration, cornering,

hydroplaning, or peak traction

characteristics.

Tread wear

The tread wear grade is a comparative

rating based on the wear rate of the tyre

when tested under controlled condi-

tions on a specified government test

course. For example, a tyre graded 150

would wear one-and-a-half times (1½)

as well on the government course as a

tyre graded 100.

9-37

Maintenance

Temperature - A, B & C

CAUTION

The temperature grades are A (the

highest), then B and C representing the

tyre’s resistance to the generation of

heat and its ability to dissipate heat

when tested under controlled condi-

tions on a specified indoor laboratory

test wheel.

Sustained high temperature can cause

the material of the tyre to degenerate

and reduce tyre life, and excessive

temperature can lead to sudden tyre

failure. Grades B and A represent high-

er levels of performance on the labora-

tory test wheel than the minimum re-

quired by law.

Because the sidewall of a low aspect

ratio tyre is shorter than a standard

tyre, the rim of the wheel and the tyre

itself is more easily susceptible to

damage. Use caution when driving

and follow the guidelines below to

help minimise damage to the wheel

and tyre:

• When driving on a rough road or

driving off a road, be careful not to

damage the tyres and wheels. Af-

ter driving, inspect the tyres and

wheels.

• When passing over a pothole,

speed bump, manhole, or curb

stone, drive the vehicle slowly so

as not to damage the tyres and

wheels.

WARNING

The temperature grade for this tyre

is established for a tyre that is prop-

erly inflated and not overloaded. Ex-

cessive speed, under-inflation, over-

inflation, or excessive loading, either

separately or in combination, can

cause heat build-up and possible

sudden tyre failure. This may cause

loss of vehicle control resulting in

an accident.

• If the tyre is subjected to a severe

impact, we recommend you have

the tyre and wheel inspected by a

HYUNDAI authorised repairer.

• Inspect the tyre condition and

pressure every 1,800 miles (3,000

km) to prevent tyre damage.

• It is not easy to recognise tyre

damage with your own eyes. But if

there is the slightest hint of tyre

damage, have the tyre checked or

replaced because the tyre damage

may cause air leakage from the

tyre.

Low aspect ratio tyres

Low aspect ratio tyres, the aspect ratio

is lower than 50, are provided for sporty

looks.

• If the tyre is damaged by driving

on a rough road, off road, pothole,

manhole, or kerb stone, it will not

be covered by the warranty.

Because low aspect ratio tyres are opti-

mised for handling and braking, their

sidewall is a little stiffer than a standard

tyre. Also low aspect ratio tyres tend to

be wider and consequently have a

greater contact patch with the road sur-

face. In some instances they may gen-

erate more road noise compared with

standard tyres.

9-38

09

FUSES

Blade type

If the electrical system does not work,

first check the driver’s side fuse panel.

Before replacing a blown fuse, turn the

engine and all switches off, and then

disconnect the negative battery cable.

Always replace a blown fuse with one

of the same rating.

If the replacement fuse blows, this indi-

cates an electrical problem. Avoid us-

ing the system involved. We recom-

mend that you immediately consult a

HYUNDAI authorised repairer.

Normal

Blown

Cartridge type

Normal

Blown

Information

i

Multi fuse

Three kinds of fuses are used: blade

type for lower amperage rating, car-

tridge type, and multi fuse for higher

amperage ratings.

Normal

Blown

WARNING

OTA070039

NEVER replace a fuse with anything

but another fuse of the same rating.

A vehicle’s electrical system is protect-

ed from electrical overload damage by

fuses.

This vehicle has 2 (or 3) fuse panels,

one located in the driver’s side panel

bolster, the other in the engine com-

partment.

If any of your vehicle’s lights, accesso-

ries, or controls do not work, check the

appropriate circuit fuse. If a fuse has

blown, the element inside the fuse will

be melted or broken.

• A higher capacity fuse could cause

damage and possibly cause a fire.

• Do not install a wire or aluminium

foil instead of the proper fuse -

even as a temporary repair. It may

cause extensive wiring damage

and possibly a fire.

NOTICE

Do not use a screwdriver or any oth-

er metal object to remove fuses be-

cause it may cause a short circuit

and damage the system.

9-39

Maintenance

7. Push in a new fuse of the same rat-

ing, and make sure it fits tightly in the

clips. If it fits loosely, we recommend

that you consult a HYUNDAI autho-

rised repairer.

Instrument panel fuse

replacement

In an emergency, if you do not have a

spare fuse, use a fuse of the same rat-

ing from a circuit you may not need for

operating the vehicle, such as the ciga-

rette lighter fuse.

If the headlights or other electrical com-

ponents do not work and the fuses are

undamaged, check the fuse panel in

the engine compartment. If a fuse is

blown, it must be replaced with the

same rating.

OAC3083015R

1. Turn the vehicle off.

2. Turn all other switches OFF.

3. Open the fuse panel cover.

4. Refer to the label on the inside of the

fuse panel cover to locate the sus-

pected fuse location.

OAC3089017TU

5. Pull the suspected fuse straight out.

Use the removal tool provided in the

engine compartment fuses panel.

6. Check the removed fuse; replace it if

it is blown. Spare fuses are provided

in the instrument panel fuse panels

(or in the engine compartment fuse

panel).

9-40

09

Multi fuse (Main fuse)

Engine compartment panel

fuse replacement

OAC3089018TU

OAC3089017TU

If the multi fuse is blown, it must be re-

1. Turn the vehicle off.

2. Turn all other switches OFF.

moved as follows:

1. Turn the vehicle off.

2. Disconnect the negative battery ca-

ble.

3. Remove the fuse panel cover by

pressing the tab and pulling it up.

3. Remove the fuse panel cover by

pressing the tab and pulling up.

4. Check the removed fuse; replace it if

it is blown. To remove or insert the

fuse, use the removal tool in the en-

gine compartment fuse panel cover.

5. Push in a new fuse of the same rat-

ing, and make sure it fits tightly in the

clips. If it fits loosely, we recommend

that you consult a HYUNDAI autho-

rised repairer.

4. Remove the nuts shown in the pic-

ture above.

5. Replace the fuse with a new one of

the same rating.

6. Reinstall in the reverse order of re-

moval.

If the multi fuse is blown, we recom-

mend that you consult a HYUNDAI au-

thorised repairer.

NOTICE

After checking the fuse panel in the

engine compartment, securely

install the fuse panel cover. You may

hear a clicking sound if the cover is

securely latched. If it is not securely

latched, electrical failure may occur

from water contact.

9-41

Maintenance

Fuse/relay panel description

Driver’s side fuse panel

Information

i

Not all fuse panel descriptions in this

manual may be applicable to your ve-

hicle. It is accurate at the time of print-

ing. When you inspect the fuse box on

your vehicle, refer to the fuse box label.

OAC3083020R

Inside the fuse/relay box covers, you

can find the fuse/relay label describing

fuse/relay names and ratings.

OAC3083021TU

9-42

09

Driver’s side fuse panel

FUSE

RATING

SYMBOL

CIRCUIT PROTECTED

SRS Control Module

FUSE NAME

2

01

02

03

AIRBAG 2

10A

25A

20A

HEATED

MIRROR

A/C Control Module, Driver/

Passenger Power Outside MIrror

SAFETY P/

WINDOW

SAFETY

Driver Safety Power Window

Module

Driver/Passenger Seat Warmer

Control Module

04 SEAT WARMER

Power Window Main Switch,

[LHD] Passenger Power Window

Switch

RH

05 P/WINDOW RH

25A

TCM, ATM Shift Lever, Back-Up

Lamp Switch

T

06

08

TCU

10A

Hazard Door Lock Switch, Data

Link Connector

8

MODULE 8

MODULE

Outside Mirror Folding/Unfolding

Relay, A/C Control Module,

Instrument Cluster

Power Window Main Switch,

[RHD] Passenger Power Window

Switch

09

MEMORY

10A

25A

MEMORY

LH

12 P/WINDOW LH

2

14

16

17

MODULE 2

MULTIMEDIA

AIRBAG 1

10A

20A

10A

7.5A

20A

7.5A

Stop Lamp Switch

MODULE

A/V & Navigation Head Unit,

Audio, Low DC-DC Converter

MULTI

MEDIA

1

SRS Control Module

Front USB Charger, Wireless

Charger Indicator

USB

19 USB CHARGER

CHARGER

3

20

21

22

A/C 3

DOOR LOCK

E-CALL

A/C Control Module

A/C

Tailgate Unlock Relay, Door Lock/

Unlock Relay

E-Call Unit

E-CALL

9-43

Maintenance

Driver’s side fuse panel

FUSE

RATING

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

Wireless Cjarger Unit, Data Link

Connector, E-Call Unit, ATM Shift

Lever ILL., Low DC-DC Converter,

Driver/Passenger Seat Warmer

Control Module,

Head Lamp LH/RH, Head Lamp

Leveling Device Switch, A/C

Control Module, A/V & Navigation

Head Unit, Audio

5

23

24

MODULE 5

10A

MODULE

3

ESP 3

10A

7.5A

10A

ESP Control Module

IBU, Stop Lamp Switch

IBU, ECM

BRAKE

SWITCH

25 BRAKE SWITCH

26

27

START

CLUSTER

Instrument Cluster

CLUSTER

IBU, Console Switch, ESP Control

Module, Clutch Sensor,

Front View Camera, Ignition Lock

& Clutch Switch

4

28

29

MODULE 4

IBU 2

10A

15A

MODULE

2

IBU

Power Outlet Relay, Power Outside

Mirror Switch, IBU, Rear USB

Charger, E-Call Unit, A/V &

Navigation Unit, Audio, Low DC-DC

Converter, Front Power Outlet

Driver/Passenger Seat Warmer

Control Module

30

ACC

10A

ACC

7

32

33

34

35

MODULE 7

WASHER

10A

15A

7.5A

20A

MODULE

Multifunction Switch

IBU

6

MODULE 6

MODULE

POWER

OUTLET

2

Front Power Outlet

POWER

OUTLET

9-44

09

Driver’s side fuse panel

FUSE

RATING

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

IBU 1

1

36

37

39

40

41

44

45

10A

7.5A

15A

20A

10A

IBU

A/C Control Module, Instrument

Cluster

IND

A/BAG IND

A/C 1

A/C Control Module, E/R Junction

Block (RLY. 12)

1

A/C

Rear Wiper Motor, E/R Junction

Block (RLY. 3)

WIPER RR

WIPER FRT 2

ECU 5

Front Wiper Motor, E/R Junction

Block (RLY. 11)

2

E5

ECM

MDPS 2

MDPS Unit

2

9-45

Maintenance

Engine compartment fuse panel

Information

i

Not all fuse panel descriptions in this

manual may be applicable to your ve-

hicle. It is accurate at the time of print-

ing. When you inspect the fuse box on

your vehicle, refer to the fuse box label.

OAC3089018TU

Inside the fuse/relay box covers, you

can find the fuse/relay label describing

fuse/relay names and ratings.

OAC3083022TU

9-46

09

Engine compartment fuse panel (for Smartstream G1.0)

SYMBOL

RELAY NAME

Main Relay

TYPE

MINI

RELAY NUMBER

RLY.1

RLY.2

RLY.3

E178

E179

E180

MAIN

FUEL

Fuel Pump Relay

Rear Wiper Relay

MICRO

PUMP

2

Cooling Fan Low Relay

RLY.4

E181

HI

Front Wiper High Relay

A/CON Relay

MICRO

RLY.5

RLY.6

RLY.7

RLY.8

RLY.9

RLY.10

RLY.11

RLY.12

E182

E183

E184

E185

E186

E187

E188

E189

A/C

Start Relay

1

Cooling Fan High Relay

B/Alarm Horn Relay

Horn Relay

LO

Front Wiper Low Relay

Blower Relay

9-47

Maintenance

Engine compartment fuse panel (for Smartstream G1.0)

FUSE

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

RATING

125A (Without

ISG)

Alternator, Multi Fuse - F02, Fuse -

F03/F05/F06/F07/F08

01

ALT

150A

(With ISG)

02

03

MDPS

80A

40A

30A

40A

10A

MDPS Unit

1

BLOWER

E/R Junction Block (RLY.12)

ICU Junction Block (Rear Defogger

Relay)

05 RR DEFOG

2

06

07

08

09

ABS2

ESP Control Module

POWER

OUTLET1

ICU Junction Block (Power Outlet

Relay)

1

POWER

OUTLET

1

ABS1

ESP Control Module

Front Wiper Motor, ECM, IBU, E/R

Junction Block (RLY.11)

1

WIPER1

[With Smart Key] PDM Relay Box

(IG1, ACC Relay)

[W/O Smart Key] Ignition Switch

10

IG1

30A

IG1

11

12

C/FAN

AMT2

30A

40A

E/R Junction Block (RLY.4, RYL.8)

2

TCM

AMT

ICU Junction Block (Long Term

Load Latch Relay, Fuse - F01/F08/

F21/F25/F29)

ICU Junction Block (Power Window

Relay, Fuse - F03/F04)

ICU Junction Block (IPS2 (4CH)/

IPS4 (4CH)/IPS6 (2CH)/IPS9 (2CH)/

IPS10 (1CH))

3

13

14

15

BATT3

BATT2

BATT4

30A

50A

40A

2

4

E3

16

17

18

ECU3

HORN

15A

10A

ECM

E/R Junction Block (RLY.9, RLY.10)

E/R Junction Block (RLY.6)

1

A/CON1

A/C

ICU Junction Block (IPS1 (4CH)/

IPS3 (4CH)/IPS5 (2CH)/IPS7 (2CH)/

IPS8 (2CH)/IPS11 (1CH))

1

19

BATT1

50A

9-48

09

Engine compartment fuse panel (for Smartstream G1.0)

FUSE

RATING

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

1

20

AMT1

40A

TCM

AMT

E/R Junction Block (RLY.7)

[With Smart Key] PDM Relay Box

(IG2 Relay)[W/O Smart Key] Ignition

Switch

21

23

IG2

30A

IG2

3

AMT3

15A

10A

15A

30A

15A

TCM

AMT

FUEL

24 FUEL PUMP

E/R Junction Block (RLY.2)

Battery Sensor

PUMP

25

27

29

30

AMS

ECU4

AMS

E4

ECM, Ignition Lock & Clutch Switch

E/R Junction Block (RLY.1)

Ignition Coil #1/#2/#3

E1

ECU1

IGN

IGN COIL

COIL

ECM, E/R Junction Block (RLY.2),

Injector #1-1/#1-2/#2-1/#2-2/#3-

1/#3-2

31

INJECTOR

15A

INJECTOR

E/R Junction Block (RLY.4, RLY.6,

RLY. 8), ECM,

Oil Control Valve #1/#2 (Intake/

Exhaust),

E2

34

ECU2

15A

Oxygen Sensor (Up/Down), Purge

Control Solenoid Valve

9-49

Maintenance

Engine compartment fuse panel (for Smartstream G1.2 )

SYMBOL

RELAY NAME

Main Relay

TYPE

MINI

RELAY NUMBER

RLY.1

RLY.2

RLY.3

E278

E279

E280

MAIN

FUEL

Fuel Pump Relay

Rear Wiper Relay

MICRO

PUMP

2

Cooling Fan Low Relay

RLY.4

E281

HI

Front Wiper High Relay

A/CON Relay

MICRO

RLY.5

RLY.6

RLY.7

RLY.8

RLY.9

RLY.10

RLY.11

RLY.12

E282

E283

E284

E285

E286

E287

E288

E289

A/C

Start Relay

1

Cooling Fan High Relay

B/Alarm Horn Relay

Horn Relay

LO

Front Wiper Low Relay

Blower Relay

9-50

09

Engine compartment fuse panel (for Smartstream G1.2 )

FUSE

RATING

125A

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

(Without ISG) Alternator, Multi Fuse - F02, Fuse -

01

ALT

150A

F03/F05/F06/F07/F08

(With ISG)

02

03

MDPS

80A

40A

30A

40A

10A

MDPS Unit

1

BLOWER

E/R Junction Block (RLY.12)

ICU Junction Block (Rear Defogger

Relay)

05 RR DEFOG

2

06

07

08

09

ABS2

ESP Control Module

POWER

OUTLET1

ICU Junction Block (Power Outlet

Relay)

1

POWER

OUTLET

1

ABS1

ESP Control Module

Front Wiper Motor, ECM, IBU, E/R

Junction Block (RLY.11)

1

WIPER1

[With Smart Key] PDM Relay Box

(IG1, ACC Relay)

[W/O Smart Key] Ignition Switch

10

IG1

30A

IG1

11

12

C/FAN

AMT2

30A

40A

E/R Junction Block (RLY.4, RYL.8)

2

TCM

AMT

ICU Junction Block (Long Term Load

Latch Relay, Fuse - F01/F08/F21/F25/

F29)

ICU Junction Block (Power Window

Relay, Fuse - F03/F04)

ICU Junction Block (IPS2 (4CH)/IPS4

(4CH)/IPS6 (2CH)/IPS9 (2CH)/IPS10

(1CH))

3

13

14

15

BATT3

BATT2

BATT4

30A

50A

40A

2

4

E3

16

17

18

ECU3

HORN

15A

10A

ECM

E/R Junction Block (RLY.9, RLY.10)

E/R Junction Block (RLY.6)

1

A/CON1

A/C

ICU Junction Block (IPS1 (4CH)/IPS3

(4CH)/IPS5 (2CH)/IPS7 (2CH)/IPS8

(2CH)/IPS11 (1CH))

1

19

BATT1

50A

9-51

Maintenance

Engine compartment fuse panel (for Smartstream G1.2 )

FUSE

RATING

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

1

20

AMT1

40A

TCM

AMT

E/R Junction Block (RLY.7) [With

Smart Key] PDM Relay Box (IG2

Relay)

21

IG2

30A

IG2

[W/O Smart Key] Ignition Switch

3

23

24

25

27

29

30

AMT3

15A

10A

15A

30A

15A

TCM

AMT

FUEL

PUMP

FUEL

E/R Junction Block (RLY.2)

Battery Sensor

PUMP

AMS

ECU4

AMS

E4

ECM, Ignition Lock & Clutch Switch

E/R Junction Block (RLY.1)

Ignition Coil #1/#2/#3

E1

ECU1

IGN

IGN COIL

COIL

ECM, E/R Junction Block (RLY.2),

Injector #1-1/#1-2/#2-1/#2-2/#3-1/#3-

2/#4-1/#4-2

31 INJECTOR

15A

INJECTOR

E/R Junction Block (RLY.4, RLY.6,

RLY. 8), ECM,

Oil Control Valve #1/#2 (Intake/

Exhaust),

E2

34

ECU2

15A

Oxygen Sensor (Up/Down), Purge

Control Solenoid Valve

9-52

09

Engine compartment fuse panel (for Smart stream G1.0 T-GDi )

SYMBOL

RELAY NAME

Main Relay

TYPE

MINI

RELAY NUMBER

RLY.1

RLY.2

RLY.3

E378

E379

E380

MAIN

FUEL

Fuel Pump Relay

Rear Wiper Relay

MICRO

PUMP

2

Cooling Fan Low Relay

RLY.4

E381

HI

Front Wiper High Relay

A/CON Relay

MICRO

RLY.5

RLY.6

RLY.7

RLY.8

RLY.9

RLY.10

RLY.11

RLY.12

E382

E383

E384

E385

E386

E387

E388

E389

A/C

Start Relay

1

Cooling Fan High Relay

B/Alarm Horn Relay

Horn Relay

LO

Front Wiper Low Relay

Blower Relay

9-53

Maintenance

Engine compartment fuse panel (for Smart stream G1.0 T-GDi )

FUSE

RATING

125A

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

(Without ISG) Alternator, Multi Fuse - F02, Fuse -

01

ALT

150A

F03/F05/F06/F07/F08

(With ISG)

02

03

05

06

07

08

09

MDPS

BLOWER

RR DEFOG

ABS2

80A

40A

30A

40A

10A

MDPS Unit

1

E/R Junction Block (RLY.12)

ICU Junction Block (Rear Defogger

Relay)

2

ESP Control Module

POWER

OUTLET1

ICU Junction Block (Power Outlet

Relay)

1

POWER

OUTLET

1

ABS1

ESP Control Module

Front Wiper Motor, ECM, IBU, E/R

Junction Block (RLY.11)

1

WIPER1

[With Smart Key] PDM Relay Box

(IG1, ACC Relay)

[W/O Smart Key] Ignition Switch

10

IG1

30A

IG1

11

12

C/FAN

AMT2

30A

40A

E/R Junction Block (RLY.4, RYL.8)

2

TCM

AMT

ICU Junction Block (Long Term

Load Latch Relay, Fuse - F01/F08/

F21/F25/F29)

ICU Junction Block (Power Window

Relay, Fuse - F03/F04)

ICU Junction Block (IPS2 (4CH)/

IPS4 (4CH)/IPS6 (2CH)/IPS9

(2CH)/IPS10 (1CH))

3

13

14

15

BATT3

BATT2

BATT4

30A

50A

40A

2

4

E3

16

17

18

ECU3

HORN

15A

10A

ECM

E/R Junction Block (RLY.9, RLY.10)

E/R Junction Block (RLY.6)

1

A/CON1

A/C

ICU Junction Block (IPS1 (4CH)/

IPS3 (4CH)/IPS5 (2CH)/IPS7

(2CH)/IPS8 (2CH)/IPS11 (1CH))

1

19

BATT1

50A

9-54

09

Engine compartment fuse panel (for Smart stream G1.0 T-GDi )

FUSE

RATING

SYMBOL

CIRCUIT PROTECTED

FUSE NAME

1

20

21

AMT1

40A

TCM

AMT

E/R Junction Block (RLY.7)

[With Smart Key] PDM Relay Box

(IG2 Relay)[W/O Smart Key]

Ignition Switch

IG2

30A

IG2

3

23

24

25

27

29

30

AMT3

FUEL PUMP

AMS

15A

10A

15A

30A

15A

TCM

AMT

FUEL

E/R Junction Block (RLY.2)

Battery Sensor

PUMP

AMS

E4

ECU4

ECM, Ignition Lock & Clutch Switch

E/R Junction Block (RLY.1)

Ignition Coil #1/#2/#3

E1

ECU1

IGN

IGN COIL

COIL

ECM, E/R Junction Block (RLY.2),

Injector #1-1/#1-2/#2-1/#2-2/#3-

1/#3-2

31

INJECTOR

15A

INJECTOR

E/R Junction Block (RLY.4, RLY.6,

RLY. 8), ECM,

Oil Control Valve #1/#2 (Intake/

Exhaust),

E2

34

ECU2

15A

Oxygen Sensor (Up/Down), Purge

Control Solenoid Valve

9-55

Maintenance

LIGHT BULBS

We recommend that you consult a

HYUNDAI authorised repairer to re-

place most vehicle light bulbs. It is diffi-

cult to replace vehicle light bulbs be-

cause other parts of the vehicle must

be removed before you can get to the

bulb. This is especially true for remov-

ing the headlight assembly to get to the

bulb(s).

Information

i

The headlight and tail light lenses

could appear frosty if the vehicle is

washed after driving or the vehicle is

driven at night in wet weather. This

condition is caused by temperature dif-

ference between the light inside and

outside and, it does not indicate a

problem with your vehicle. When

moisture condenses in the light, it will

be removed after driving with the

headlight on. The removable level may

differ depending on light size, light po-

sition and environmental condition.

However, if moisture is not removed,

we recommend that your vehicle is in-

spected by a HYUNDAI authorised re-

pairer.

Removing/installing the headlight as-

sembly can result in damage to the ve-

hicle.

WARNING

Prior to replacing a light, depress

the foot brake, move the shift lever

into the N (Neutral, for Automated

manual transmission vehicle) or

neutral (for manual transmission ve-

hicle), apply the parking brake, place

the ignition switch in the LOCK/OFF

position, and take the key with you

when leaving the vehicle to avoid

sudden movement of the vehicle and

to prevent possible electric shock.

Information (For Europe)

i

Traffic Change

The low beam light distribution is

asymmetric. If you go abroad to a

country with opposite traffic direction,

this asymmetric part will dazzle on-

coming car driver. To prevent dazzle,

ECE regulation demand several tech-

nical solutions (for example, automatic

change system, adhesive sheet, down

aiming). These headlights are designed

not to dazzle opposite drivers. So, you

need not change your headlights in a

country with opposite traffic direction.

Be aware the bulbs may be hot and

may burn your fingers.

NOTICE

Be sure to replace the burned-out

bulb with one of the same wattage

rating. Otherwise, it may cause dam-

age to the fuse or electric wiring sys-

tem.

9-56

09

Type B

Headlight, Position Light,

Turn signal Light, Fog Light

and Daytime Running Light,

Low Beam Assist-Static light

bulb replacement

Type A

OAC3083023TU

Type C

OAC3083024TU

(1) Headlight (Low/High) *¹

(2) Turn Signal Light

(3) Daytime Running Light

& Position Light

OAC3N082023TU

(4) Front Fog Light (if equipped)

(1) Headlight (Low/High) *²

(2) Low Beam Assist-Static Light

(3) Turn Signal Light

(4) Daytime Running Light

& Position Light

*¹: MFR (Multi Focus Reflector) Head-

light

(5) Front Fog Light (if equipped)

*²: Bi-Function Projection Headlight

9-57

Maintenance

Headlight (Low/High)

1. Turn the front tyre at a right angle.

OLMB073042L

WARNING

OAC3089042TU

OAC3089043TU

OAC3089044TU

• Handle halogen bulbs with care.

Halogen bulbs contain pressur-

ized gas that will produce flying

pieces of glass that could cause

injuries if broken.

• Wear eye protection when chang-

ing a bulb. Allow the bulb to cool

down before handling it.

• Always handle them carefully, and

avoid scratches and abrasions. If the

bulbs are lit, avoid contact with liq-

uids.

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only when

installed in a headlight.

• If a bulb becomes damaged or

cracked, replace it immediately and

carefully dispose of it.

2. Remove the Wheel guard clips (B),

bumper cover bolt (A) and bumper

upper cover bolt (C).

3. Push the wheel guard aside and re-

move the headlight bulb cover by

turning it counterclockwise.

9-58

09

Type A

Information

i

Bi-Function projection headlight

This headlight is bi-function type that

switches the low beam to high or the

high beam to low using solenoid sys-

tem. So, the moving sound may be

heard when the headlight switches the

low beam to high or the high beam to

low and it does not indicate malfunc-

tion of the headlight.

OAC3089045TU

Type B,C

Type A

OAC3089051TU

[1] : Headlight

OAC3089035TU

Type B,C

4. Disconnect the headlight bulb sock-

et-connector.

5. Unsnap the headlight bulb retaining

wire by depressing the end and

pushing it upward.

6. Remove the bulb from the headlight

assembly.

7. Install a new headlight bulb and snap

the headlight bulb retaining wire into

position by aligning the wire with the

groove on the bulb.

OAC3089036TU

[2] : Low Beam Assist-Static Light

[3] : Turn signal light

8. Connect the headlight bulb socket

connector.

9. Install the headlight bulb cover by

Turn signal light, Low Beam

Assist-Static Light

1. Open the bonnet.

2. Remove the turn signal light or low

beam assist-static light bulb cover by

turning it counterclockwise.

turning it clockwise.

10. Install the wheel guard in the re-

verse order.

9-59

Maintenance

3. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

2. Reach your hand into the back of the

front bumper.

3. Disconnect the power connector

from the socket.

4. Insert a new bulb by inserting it into

the socket and rotating it until it locks

into place.

5. Install the socket in the assembly by

aligning the tabs on the socket with

the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

6. Install the turn signal light or low

beam assist-static light bulb cover by

turning it clockwise.

4. Remove the bulb-socket from the

housing by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots on the

housing.

5. Install the new bulb-socket into the

housing by aligning the tabs on the

socket with the slots in the housing.

Push the socket into the housing and

turn the socket clockwise.

6. Connect the power connector to the

socket.

7. Reinstall the front bumper under

Daytime Running Light &

Position Light, Front Fog Light

(if equipped)

cover.

Daytime Running Light &

Position Light

(LED Type, if equipped)

Daytime Running Light & Position Light

Your vehicle is equipped with LED

lights. LED lights do not have replace-

able bulbs. If the LED light does not op-

erate, we recommend that the vehicle

be checked by a HYUNDAI authorised

repairer.

OAC3089038TU

Front Fog light

OAC3089037TU

1. Remove the under cover by rotating

the screws and bolts.

9-60

09

5. To aim the low beam left or right,

Headlight and front fog light

aiming

Headlight aiming

turn the driver clockwise or counter-

clockwise. To aim the low beam up

or down, turn the driver clockwise or

counterclockwise.

Type A

To aim the high beam up or down,

turn the driver clockwise or counter-

clockwise.

Front fog light aiming

Type A

OAC3089039TU

Type B,C

OAC3083026TU

Type B

OAC3089040TU

1. Inflate the tyres to the specified pres-

sure and remove any loads from the

vehicle except the driver, spare tyre,

and tools.

2. The vehicle should be placed on a

OAC3N083026TU

flat floor.

3. Draw vertical lines (Vertical lines

passing through respective head

light centres) and a horizontal line

(Horizontal line passing through cen-

tre of head lights) on the screen.

4. With the headlight and battery in nor-

mal condition, aim the headlights so

the brightest portion falls on the hori-

zontal and vertical lines.

The front fog light can be aimed as the

same manner of the head lights aiming.

With the front fog lights and battery nor-

mal condition, aim the front fog lights.

To aim the front fog light up or down,

turn the driver clockwise or counter-

clockwise.

9-61

Maintenance

Aiming point (5 Door)

H1 : Lighting centre Ground clearance of Headlight Low & High Beam

H3 : Lighting centre Ground clearance of Front fog light

W1 : Lighting centre Distance between Headlight Low & High Beam

W3 : Lighting centre Distance between Front fog light

OAC3083027TU

Unit: mm (in)

W3

H3

Vehicle condition

Multi Focus Reflector

H1

W1

Fog

768

1,342

1,361

(53.6)

Headlight

Bi-Function Projection

Headlight

(30.23)

761.5

(29.9)

(52.8)

1,357

(53.4)

392

(15.4)

Without driver

Multi Focus Reflector

Headlight

761

(29.9)

1,342

(52.8)

385

1,361

(53.6)

With driver

(15.2)

Bi-Function Projection

Headlight

754.5

(29.7)

1,357

(53.4)

9-62

09

Aiming point (N line)

H1 : Lighting centre Ground clearance of Headlight Low & High Beam

H3 : Lighting centre Ground clearance of Front fog light

W1 : Lighting centre Distance between Headlight Low & High Beam

W3 : Lighting centre Distance between Front fog light

OAC3N083027TU

Unit: mm (in)

W3

H3

Vehicle condition

Multi Focus Reflector

H1

W1

Fog

768

1,342

1,309

(51.5)

Headlight

Bi-Function Projection

Headlight

(30.23)

761.5

(29.9)

(52.8)

1,357

(53.4)

378

(14.9)

Without driver

Multi Focus Reflector

Headlight

761

(29.9)

1,342

(52.8)

371

1,309

(51.5)

With driver

(14.6)

Bi-Function Projection

Headlight

754.5

(29.7)

1,357

(53.4)

9-63

Maintenance

Head light low beam

OAC3N080033TU

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting

the horizontal aiming.

4. If head light levelling device is equipped, adjust the head light levelling device

switch with 0 positions.

9-64

09

Front fog light

Based on 10m screen

OAC3089034TU

1. Turn the front fog light on with the driver (75 kg) aboard.

2. The cut-off line should be projected in the allowable range (shaded region).

9-65

Maintenance

4. Remove the bulb by pulling it straight

Side repeater light replacement

out.

5. Insert a new bulb in the socket.

6. Reassemble the socket and the lens

part.

7. Connect the bulb electrical connec-

tor.

8. Reinstall the light assembly to the

body of the vehicle.

Rear combination light bulb

replacement

OAI3089022

Type A

If the LED light does not operate, we

recommend you to have the vehicle

checked by a HYUNDAI authorised re-

pairer.

OAC3N083059TU

(1) Turn Signal Light

(2) Tail/Stop Light

(3) Reflex Reflector Light

(4) Rear Fog Light

(5) Back-up Light

OAC3083047TU

Type B

1. Remove the light assembly from the

vehicle by prying the lens and pulling

the assembly out.

2. Disconnect the bulb electrical con-

nector.

3. Separate the socket and the lens

parts by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the lens part.

9-66

09

2. Loosen the light assembly retaining

Type B

screws with a cross-tip screwdriver.

3. Remove the rear combination light

assembly from the body of the vehi-

cle.

OAC3N083058TU

(1) Tail Light

(2) Stop Light

(3) Turn signal light

(4) Reflex Reflector Light

(5) Rear fog Light

(6) Back-up Light

OAC3089041TU

[1] : Turn Signal Light, [2] : Tail/Stop Light

4. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

Turn Signal Light, Tail/Stop Light

5. Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

6. Insert a new bulb by inserting it into

the socket and rotating it until it locks

into place.

OAC3089048TU

7. Install the socket in the assembly by

aligning the tabs on the socket with

the slots in the assembly. Push the

socket into the assembly and turn

the socket clockwise.

8. Reinstall the light assembly to the

body of the vehicle.

OAC3089049TU

1. Open the tailgate

9-67

Maintenance

Rear fog light, Back-up Light

High mounted stop light

replacement

OAC3N083029TU

OAC3089046TU

[1] : Rear Fog Light, [2] : Back-up Light

1. Remove the rear tyre and wheel cov-

If the LED light does not operate, we

recommend you to have the vehicle

checked by a HYUNDAI authorised re-

pairer.

er.

2. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

3. Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

License plate light bulb

replacement

4. Insert a new bulb in the socket.

5. Reinstall the light assembly to the

body of the vehicle.

OAI3089029

1. Using a flat-blade screwdriver gently

pry the lens cover from the light

housing.

2. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

3. Remove the bulb by pulling it straight

out.

4. Install a new bulb.

5. Reinstall in the reverse order.

9-68

09

Interior light bulb replacement

NOTICE

Room lamp

• Type A

Be careful not to damage the cover,

tab, and plastic housing.

OAC3083030TU

• Type B

OIB074041

Luggage room lamp

OAC3089031TU

1. Using a flat-head screwdriver, gently

pry the lens from the interior light

housing.

2. Remove the bulb by pulling it straight

out.

3. Install a new bulb into the socket.

4. Align the lens tabs with the interior

light housing notches and snap the

lens into place.

9-69

Maintenance

APPEARANCE CARE

Exterior care

Even prompt washing with plain water

may not completely remove all these

deposits.

NOTICE

If you park your vehicle near a stain-

less steel sign or glass facade build-

ing, the vehicle’s exterior plastic

parts such as a bumper, spoiler, gar-

nish, light or exterior mirror might be

damaged due to sunlight reflected

from the sign or building. To prevent

damage of the exterior plastic parts,

you should avoid parking in areas

where light may be reflected or use a

car cover. (The exterior plastic parts

applied to your vehicle may vary.)

A mild soap, safe for use on painted

surfaces, may be used.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water. Do

not allow soap to dry on the finish.

NOTICE

• Do not use strong soap, chemical

detergents or hot water, and do

not wash the vehicle in direct sun-

light or when the body of the vehi-

cle is warm.

Exterior general caution

• Be careful when washing the side

windows of your vehicle.

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning and

caution statements that appear on the

label.

Especially, with high-pressure wa-

ter, water may leak through the

windows and wet the interior.

• To prevent damage to the plastic

parts and lights, do not clean with

chemical solvents or strong deter-

gents.

Finish maintenance

Washing

To help protect your vehicle’s finish

from rust and deterioration, wash it

thoroughly and frequently at least once

a month with lukewarm or cold water.

If you use your vehicle for off-road driv-

ing, you should wash it after each off-

road trip. Pay special attention to the

removal of any accumulation of salt,

dirt, mud, and other foreign materials.

Make sure the drain holes in the lower

edges of the doors and rocker panels

are kept clear and clean.

WARNING

Wet brakes

After washing the vehicle, test the

brakes whilst driving slowly to see if

they have been affected by water. If

braking performance is impaired,

dry the brakes by applying them

lightly whilst maintaining a slow for-

ward speed.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar deposits

can damage your vehicle’s finish if not

removed immediately.

9-70

09

High-pressure washing

NOTICE

• When using high-pressure washers,

make sure to maintain sufficient dis-

tance from the vehicle.

Matte paint finish vehicle

(if equipped)

Automatic car wash which uses ro-

tating brushes should not be used

as this can damage the surface of

your vehicle. A steam cleaner which

washes the vehicle surface at high

temperature may result the oil to ad-

here and leave stains that is difficult

to remove.

Insufficient clearance or excessive

pressure can lead to component

damage or water penetration.

• Do not spray the camera, sensors or

its surrounding area directly with a

high pressure washer. Shock applied

from high pressure water may cause

the device to not operate normally.

Use a soft cloth (for example, micro-

fiber towel or sponge) when washing

your vehicle and dry with a microfi-

ber towel. When you hand wash your

vehicle, you should not use a clean-

er that finishes with wax. If the vehi-

cle surface is too dirty (sand, dirt,

dust, contaminant, etc.), clean the

surface with water before washing

the car.

• Do not bring the nozzle tip close to

boots (rubber or plastic covers) or

connectors as they may be damaged

if they come into contact with high

pressure water.

Waxing

Wax the vehicle when water will no lon-

ger bead on the paint.

Always wash and dry the vehicle before

waxing. Use a good quality liquid or

paste wax, and follow the manufactur-

er’s instructions. Wax all metal trim to

protect it and to maintain its luster. Re-

moving oil, tar, and similar materials

with a spot remover will usually strip the

wax from the finish. Be sure to re-wax

these areas even if the rest of the vehi-

cle does not yet need waxing.

OAC3083032TU

NOTICE

• Water washing in the engine com-

partment including high pressure

water washing may cause the fail-

ure of electrical circuits located in

the engine compartment.

• Never allow water or other liquids

to come in contact with electrical/

electronic components inside the

vehicle as this may damage them.

9-71

Maintenance

Finish damage repair

NOTICE

Deep scratches or stone chips in the

painted surface must be repaired

promptly. Exposed metal will quickly

rust and may develop into a major re-

pair expense.

• Wiping dust or dirt off the body

with a dry cloth will scratch the fin-

ish.

• Do not use steel wool, abrasive

cleaners, or strong detergents

containing highly alkaline or caus-

tic agents on chrome-plated or an-

odized aluminium parts. This may

result in damage to the protective

coating and cause discolouration

or paint deterioration.

NOTICE

If your vehicle is damaged and re-

quires any metal repair or replace-

ment, be sure the body shop applies

anti-corrosion materials to the parts

repaired or replaced.

NOTICE

Matte paint finish vehicle

(if equipped)

Matte paint finish vehicle

(if equipped)

Do not use any polish protector such

as a detergent, an abrasive and a

polish. In case wax is applied, re-

move the wax immediately using a

silicon remover and if any tar or tar

contaminant is on the surface use a

tar remover to clean. However, be

careful not to apply too much pres-

sure on the painted area.

In case of matte paint finish vehicles,

it is impossible to modify only the

damaged area and repair of the

whole part is necessary. If the vehi-

cle is damaged and painting is re-

quired, we recommend that you have

your vehicle maintained and re-

paired by a HYUNDAI authorised re-

pairer. Take extreme care, as it is dif-

ficult to restore the quality after the

repair.

9-72

09

Bright-metal maintenance

WARNING

• To remove road tar and insects, use

a tar remover, not a scraper or other

sharp object.

• To protect the surfaces of bright-met-

al parts from corrosion, apply a coat-

ing of wax or chrome preservative

and rub to a high luster.

• During winter weather or in coastal

areas, cover the bright metal parts

with a heavier coating of wax or pre-

servative. If necessary, coat the parts

with non-corrosive petroleum jelly or

other protective compound.

After washing the vehicle, test the

brakes whilst driving slowly to see if

they have been affected by water. If

braking performance is impaired,

dry the brakes by applying them

lightly whilst maintaining a slow for-

ward speed.

Aluminium wheel maintenance

The aluminium wheels are coated with

a clear protective finish.

NOTICE

Underbody maintenance

• Do not use any abrasive cleaner,

polishing compound, solvent, or

wire brushes on aluminium

wheels.

Corrosive materials used for ice and

snow removal and dust control may col-

lect on the underbody. If these materi-

als are not removed, accelerated rust-

ing can occur on underbody parts such

as the fuel lines, frame, floor pan and

exhaust system, even though they have

been treated with rust protection.

Thoroughly flush the vehicle underbody

and wheel openings with lukewarm or

cold water once a month, after off-road

driving and at the end of each winter.

Pay special attention to these areas be-

cause it is difficult to see all the mud

and dirt. It will do more harm than good

to wet down the road grime without re-

moving it. The lower edges of doors,

rocker panels, and frame members

have drain holes that should not be al-

lowed to clog with dirt; trapped water in

these areas can cause rusting.

• Clean the wheel when it has

cooled.

• Use only a mild soap or neutral de-

tergent, and rinse thoroughly with

water. Also, be sure to clean the

wheels after driving on salted

roads.

• Do not wash the wheels with high-

speed car wash brushes.

• Do not use any cleanser contain-

ing acid or alkaline detergents.

9-73

Maintenance

Moisture breeds corrosion

Corrosion protection

Moisture creates the conditions in

which corrosion is most likely to occur.

For example, corrosion is accelerated

by high humidity, particularly when tem-

peratures are just above freezing. In

such conditions, the corrosive material

is kept in contact with the vehicle sur-

faces by moisture that is slow to evapo-

rate.

Mud is particularly corrosive because it

is slow to dry and holds moisture in

contact with the vehicle. Although the

mud appears to be dry, it can still retain

moisture and promote corrosion.

High temperatures can also accelerate

corrosion of parts that are not properly

ventilated so the moisture can be dis-

persed. For all these reasons, it is par-

ticularly important to keep your vehicle

clean and free of mud or accumulations

of other materials. This applies not only

to the visible surfaces but particularly to

the underside of the vehicle.

Protecting your vehicle from corro-

sion

By using the most advanced design

and construction practices to combat

corrosion, we produces vehicles of the

highest quality. However, this is only

part of the job. To achieve the long-

term corrosion resistance your vehicle

can deliver, the owner’s cooperation

and assistance is also required.

Common causes of corrosion

The most common causes of corrosion

on your vehicle are:

• Road salt, dirt and moisture that is al-

lowed to accumulate underneath the

vehicle.

• Removal of paint or protective coat-

ings; by stones, gravel, abrasion or

minor scrapes and dents which leave

unprotected metal exposed to corro-

sion.

To help prevent corrosion

High-corrosion areas

You can help prevent corrosion from

getting started by observing the follow-

ing:

If you live in an area where your vehicle

is regularly exposed to corrosive mate-

rials, corrosion protection is particularly

important. Some of the common causes

of accelerated corrosion are road salts,

dust control chemicals, ocean air and

industrial pollution.

9-74

09

Keep your vehicle clean

Keep your garage dry

The best way to prevent corrosion is to

keep your vehicle clean and free of cor-

rosive materials. Attention to the under-

side of the vehicle is particularly impor-

tant.

Don’t park your vehicle in a damp,

poorly ventilated garage. This creates a

favorable environment for corrosion.

This is particularly true if you wash your

vehicle in the garage or drive it into the

garage when it is still wet or covered

with snow, ice or mud. Even a heated

garage can contribute to corrosion un-

less it is well ventilated so moisture is

dispersed.

• If you live in a high-corrosion area —

where road salts are used, near the

ocean, areas with industrial pollution,

acid rain, etc.—, you should take ex-

tra care to prevent corrosion. In win-

ter, hose off the underside of your

vehicle at least once a month and be

sure to clean the underside thorough-

ly when winter is over.

• When cleaning underneath the vehi-

cle, give particular attention to the

components under the fenders and

other areas that are hidden from

view. Do a thorough job; just damp-

ening the accumulated mud rather

than washing it away will accelerate

corrosion rather than prevent it. Wa-

ter under high pressure and steam

are particularly effective in removing

accumulated mud and corrosive ma-

terials.

Keep paint and trim in good condition

Scratches or chips in the finish should

be covered with “touch-up” paint as

soon as possible to reduce the possibil-

ity of corrosion. If bare metal is showing

through, the attention of a qualified

body and paint shop is recommended.

Bird droppings : Bird droppings are

highly corrosive and may damage

painted surfaces in just a few hours. Al-

ways remove bird droppings as soon as

possible.

Don’t neglect the interior

Moisture can collect under the floor

mats and carpeting to cause corrosion.

Check under the mats periodically to be

sure the carpeting is dry. Use particular

care if you carry fertilizers, cleaning

materials or chemicals in the vehicle.

• When cleaning lower door panels,

rocker panels and frame members,

be sure that drain holes are kept

open so that moisture can escape

and not be trapped inside to acceler-

ate corrosion.

These should be carried only in proper

containers and any spills or leaks

should be cleaned up, flushed with

clean water and thoroughly dried.

9-75

Maintenance

Cleaning the upholstery and

interior trim

Vehicle interior surfaces

(if equipped)

Remove dust and loose dirt from interi-

or surfaces with a whisk broom or a

vacuum cleaner.

If necessary, clean interior surfaces

with a mixture of warm water and mild

non-detergent cleaner (test all cleaners

on a concealed area before use).

Interior care

Interior general precautions

Prevent chemicals such as perfume,

cosmetic oil, sun cream, hand cleaner

and air freshener from contacting the

interior parts because they may cause

damage or discolouration. If they do

contact the interior parts, wipe them off

immediately.

See the instructions that follow for the

proper way to clean vehicle interior sur-

faces.

Fabric (if equipped)

NOTICE

Remove dust and loose dirt from fabric

with a whisk broom or vacuum cleaner.

Clean with a mild soap solution recom-

mended for upholstery or carpets. Re-

move fresh spots immediately with a

fabric spot cleaner. If fresh spots do not

receive immediate attention, the fabric

can be stained and its colour can be af-

fected. Also, its fire-resistant properties

can be reduced if the material is not

properly maintained.

Never allow water or other liquids to

come in contact with electrical/elec-

tronic components inside the vehi-

cle as this may damage them.

NOTICE

When cleaning leather products

(steering wheel, seats etc.), use neu-

tral detergents or low alcohol con-

tent solutions. If you use high alco-

hol content solutions or acid/alkaline

detergents, the colour of the leather

may fade or the surface may get

stripped off.

NOTICE

Using anything but recommended

cleaners and procedures may affect

the fabric’s appearance and fire-re-

sistant properties.

9-76

09

• Caring for the leather seats

Leather (if equipped)

- Vacuum the seat periodically to re-

move dust and sand on the seat. It

will prevent abrasion or damage of

the leather and maintain its quality.

- Wipe the natural leather seat cover

often with dry or soft cloth.

- Use of proper leather protector may

prevent abrasion of the cover and

helps maintain the colour. Be sure

to read the instructions and consult

a specialist when using leather

coating or protective agent.

- Light coloured (beige, cream beige)

leather is easily contaminated and

the stain is noticeable. Clean the

seats frequently.

• Features of Seat Leather

- Leather is made from the outer skin

of an animal, which goes through a

special process to be available for

use. Since it is a natural product,

each part differs in thickness or den-

sity.

Wrinkles may appear as a natural

result of stretching and shrinking de-

pending on the temperature and hu-

midity.

- The seat is made of stretchable fab-

ric to improve comfort.

- The parts contacting the body are

curved and the side supporting area

is high which provides driving com-

fort and stability.

- Wrinkles may appear naturally from

usage. It is not a fault of the prod-

ucts.

- Avoid wiping with wet cloth. It may

cause the surface to crack.

CAUTION

• Wrinkles or abrasions which ap-

pear naturally from usage are not

covered by warranty.

• Belts with metallic accessories,

zippers or keys inside the back

pocket may damage the seat fab-

ric.

• Make sure not to wet the seat. It

may change the nature of natural

leather.

• Jeans or clothes which could

bleach may contaminate the sur-

face of the seat covering fabric.

9-77

Maintenance

• Cleaning the leather seats

Cleaning the lap/shoulder belt

webbing

- Remove all contaminations instant-

ly. Refer to instructions below for

removal of each contaminant.

- Cosmetic products (sunscreen,

foundation, etc.)

Apply cleansing cream on a cloth

and wipe the contaminated spot.

Wipe off the cream with a wet cloth

and remove water with a dry cloth.

Clean the belt webbing with any mild

soap solution recommended for clean-

ing upholstery or carpet. Follow the in-

structions provided with the soap. Do

not bleach or re-dye the webbing be-

cause this may weaken it.

Cleaning the interior window

glass

- Beverages (coffee, soft drink, etc.)

Apply a small amount of neutral de-

tergent and wipe until contamina-

tions do not smear.

If the interior glass surfaces of the ve-

hicle become fogged (that is, covered

with an oily, greasy or waxy film), they

should be cleaned with glass cleaner.

Follow the directions on the glass

cleaner container.

- Oil

Remove oil instantly with absorb-

able cloth and wipe with stain re-

mover used only for natural leather.

- Chewing gum

NOTICE

Harden the gum with ice and re-

move gradually.

Do not scrape or scratch the inside

of the rear window. This may result

in damage to the rear window de-

froster grid.

9-78

09

EMISSION CONTROL SYSTEM

The emission control system of your

vehicle is covered by a written limited

warranty. Please see the warranty in-

formation contained in the Service

Passport in your vehicle.

Your vehicle is equipped with an emis-

sion control system to meet all emis-

sion regulations.

1. Crankcase emission control

system

The positive crankcase ventilation sys-

tem is employed to prevent air pollution

caused by blow-by gases being emitted

from the crankcase. This system sup-

plies fresh filtered air to the crankcase

through the air intake hose. Inside the

crankcase, the fresh air mixes with

blow-by gases, which then pass

through the PCV valve into the induc-

tion system.

There are three emission control sys-

tems which are as follows.

(1) Crankcase emission control system

(2) Evaporative emission control sys-

2. Evaporative emission

control system

tem

(3) Exhaust emission control system

The Evaporative Emission Control Sys-

tem is designed to prevent fuel vapours

from escaping into the atmosphere.

In order to ensure the proper function of

the emission control systems, it is rec-

ommended that you have your car in-

spected and maintained by a HYUNDAI

authorised repairer in accordance with

the maintenance schedule.

Canister

Fuel vapours generated inside the fuel

tank are absorbed and stored in the on-

board canister. When the engine is run-

ning, the fuel vapours absorbed in the

canister are drawn into the surge tank

through the purge control solenoid

valve.

NOTICE

For the Inspection and Maintenance

Test (with Electronic Stability Con-

trol (ESC) system)

• To prevent the vehicle from misfir-

ing during dynamometer testing,

turn the Electronic Stability Con-

trol (ESC) system off by pressing

the ESC switch.

• After dynamometer testing is com-

pleted, turn the ESC system back

on by pressing the ESC switch

again.

9-79

Maintenance

Purge Control Solenoid Valve

(PCSV)

WARNING

Engine exhaust gases contain car-

bon monoxide (CO). Though colour-

less and odourless, it is dangerous

and could be lethal if inhaled. Follow

the instructions following to avoid

CO poisoning.

The purge control solenoid valve is

controlled by the Engine Control Mod-

ule (ECM); when the engine coolant

temperature is low during idling, the

PCSV closes so that evaporated fuel is

not taken into the engine. After the en-

gine warms-up during ordinary driving,

the PCSV opens to introduce evapo-

rated fuel to the engine.

• Do not operate the engine in confined

or closed areas (such as garages)

any more than what is necessary to

move the vehicle in or out of the area.

• When the vehicle is stopped in an

open area for more than a short time

with the engine running, adjust the

ventilation system (as needed) to

draw outside air into the vehicle.

• Never sit in a parked or stopped ve-

hicle for any extended time with the

engine running.

• When the engine stalls or fails to

start, excessive attempts to restart

the engine may cause damage to the

emission control system.

3. Exhaust emission control

system

The Exhaust Emission Control System

is a highly effective system which con-

trols exhaust emissions whilst main-

taining good vehicle performance.

Engine exhaust gas precautions

(carbon monoxide)

• Carbon monoxide can be present

with other exhaust fumes. Therefore,

if you smell exhaust fumes of any

kind inside your vehicle, have it in-

spected and repaired immediately. If

you ever suspect exhaust fumes are

coming into your vehicle, drive it only

with all the windows fully open. Have

your vehicle checked and repaired

immediately.

9-80

09

Your vehicle is equipped with a catalyt-

Operating precautions for cata-

lytic converters (if equipped)

ic converter emission control device.

Therefore, the following precautions

must be observed:

• Use only UNLEADED FUEL for petrol

engines.

• Do not operate the vehicle when

there are signs of engine malfunction,

such as misfire or a noticeable loss of

performance.

WARNING

The exhaust system and catalytic

system are very hot whilst the en-

gine is running or immediately after

the engine is turned off. To avoid SE-

RIOUS INJURY or DEATH:

• Do not park, idle, or drive the ve-

hicle over or near flammable ob-

jects, such as grass, vegetation,

paper, leaves, etc. A hot exhaust

system can ignite flammable

items under your vehicle.

• Do not misuse or abuse the engine.

Examples of misuse are coasting

with the engine off and descending

steep grades in gear with the engine

off.

• Do not operate the engine at high idle

speed for extended periods (5 min-

utes or more).

• Do not modify or tamper with any part

of the engine or emission control sys-

tem. We recommend that all inspec-

tions and adjustments are made by a

HYUNDAI authorised repairer.

• Avoid driving with a very low fuel lev-

el. If you run out of petrol, it could

cause the engine to misfire and result

in excessive loading of the catalytic

converter.

• Keep away from the exhaust

system and catalytic converter

or you may get burned. Also, do

not emove the heat sink around

the exhaust system, do not seal

the bottom of the vehicle, and

do not coat the vehicle for corro-

sion control. It may present a

fire risk under certain condi-

tions.

Failure to observe these precautions

could result in damage to the catalytic

converter and to your vehicle. Addition-

ally, such actions could void your war-

ranties.

9-81

Maintenance

Petrol Particulate Filter (GPF)

(if equipped)

The Petrol Particulate Filter (GPF) sys-

tem removes the soot in the exhaust

gas.

The GPF system automatically burns

(or oxidizes) the accumulated soot in

accordance with driving situations, un-

like a disposable air filter.

In other words, the accumulated soot is

automatically purged out by the engine

control system and by the high exhaust-

gas temperature at normal/ high driving

speeds.

WARNING

Petrol Fuel

(if equipped with GPF)

We recommend you to use only the

regulated petrol fuels, when your ve-

hicle is equipped with the GPF sys-

tem.

When you use other petrol fuels

which contain unspecified additives,

they may damage the GPF system

and cause exhaust emission prob-

lems.

However, when the vehicle is continu-

ally driven at repeated short distances

or driven at low speed for a long time,

the accumulated soot may not be auto-

matically removed because of low ex-

haust gas temperature. In this case, the

accumulated soot may reach a certain

amount regardless of the soot oxidiza-

tion process, then the GPF light will il-

luminate.

The Petrol Particulate Filter (GPF) Light

stops illuminating, when the driving

speed exceeds 50 mph (80 km/h) with

engine RPM 1,500 ~ 4,000 and the

gear in the 3rd position or above for

about 30 minutes.

When the GPF light starts to blink or the

waning message “Check exhaust sys-

tem” pops up even though the vehicle

was driven as mentioned above, we

recommend that you have the GPF

system checked by a HYUNDAI autho-

rised repairer.

With the GPF light blinking for an ex-

tended period of time, it may damage

the GPF system and lower the fuel

economy.

9-82

Maintenance for Your Hyundai Bayon SUV Second Generation (2021-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals