Get Maintenance -> Light bulbs Guide for Hyundai Bayon SUV Second Generation (2021-2024)

Maintenance

LIGHT BULBS

We recommend that you consult a

HYUNDAI authorised repairer to re-

place most vehicle light bulbs. It is diffi-

cult to replace vehicle light bulbs be-

cause other parts of the vehicle must

be removed before you can get to the

bulb. This is especially true for remov-

ing the headlight assembly to get to the

bulb(s).

Information

i

The headlight and tail light lenses

could appear frosty if the vehicle is

washed after driving or the vehicle is

driven at night in wet weather. This

condition is caused by temperature dif-

ference between the light inside and

outside and, it does not indicate a

problem with your vehicle. When

moisture condenses in the light, it will

be removed after driving with the

headlight on. The removable level may

differ depending on light size, light po-

sition and environmental condition.

However, if moisture is not removed,

we recommend that your vehicle is in-

spected by a HYUNDAI authorised re-

pairer.

Removing/installing the headlight as-

sembly can result in damage to the ve-

hicle.

WARNING

Prior to replacing a light, depress

the foot brake, move the shift lever

into the N (Neutral, for Automated

manual transmission vehicle) or

neutral (for manual transmission ve-

hicle), apply the parking brake, place

the ignition switch in the LOCK/OFF

position, and take the key with you

when leaving the vehicle to avoid

sudden movement of the vehicle and

to prevent possible electric shock.

Information (For Europe)

i

Traffic Change

The low beam light distribution is

asymmetric. If you go abroad to a

country with opposite traffic direction,

this asymmetric part will dazzle on-

coming car driver. To prevent dazzle,

ECE regulation demand several tech-

nical solutions (for example, automatic

change system, adhesive sheet, down

aiming). These headlights are designed

not to dazzle opposite drivers. So, you

need not change your headlights in a

country with opposite traffic direction.

Be aware the bulbs may be hot and

may burn your fingers.

NOTICE

Be sure to replace the burned-out

bulb with one of the same wattage

rating. Otherwise, it may cause dam-

age to the fuse or electric wiring sys-

tem.

9-56

09

Type B

Headlight, Position Light,

Turn signal Light, Fog Light

and Daytime Running Light,

Low Beam Assist-Static light

bulb replacement

Type A

OAC3083023TU

Type C

OAC3083024TU

(1) Headlight (Low/High) *¹

(2) Turn Signal Light

(3) Daytime Running Light

& Position Light

OAC3N082023TU

(4) Front Fog Light (if equipped)

(1) Headlight (Low/High) *²

(2) Low Beam Assist-Static Light

(3) Turn Signal Light

(4) Daytime Running Light

& Position Light

*¹: MFR (Multi Focus Reflector) Head-

light

(5) Front Fog Light (if equipped)

*²: Bi-Function Projection Headlight

9-57

Maintenance

Headlight (Low/High)

1. Turn the front tyre at a right angle.

OLMB073042L

WARNING

OAC3089042TU

OAC3089043TU

OAC3089044TU

• Handle halogen bulbs with care.

Halogen bulbs contain pressur-

ized gas that will produce flying

pieces of glass that could cause

injuries if broken.

• Wear eye protection when chang-

ing a bulb. Allow the bulb to cool

down before handling it.

• Always handle them carefully, and

avoid scratches and abrasions. If the

bulbs are lit, avoid contact with liq-

uids.

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only when

installed in a headlight.

• If a bulb becomes damaged or

cracked, replace it immediately and

carefully dispose of it.

2. Remove the Wheel guard clips (B),

bumper cover bolt (A) and bumper

upper cover bolt (C).

3. Push the wheel guard aside and re-

move the headlight bulb cover by

turning it counterclockwise.

9-58

09

Type A

Information

i

Bi-Function projection headlight

This headlight is bi-function type that

switches the low beam to high or the

high beam to low using solenoid sys-

tem. So, the moving sound may be

heard when the headlight switches the

low beam to high or the high beam to

low and it does not indicate malfunc-

tion of the headlight.

OAC3089045TU

Type B,C

Type A

OAC3089051TU

[1] : Headlight

OAC3089035TU

Type B,C

4. Disconnect the headlight bulb sock-

et-connector.

5. Unsnap the headlight bulb retaining

wire by depressing the end and

pushing it upward.

6. Remove the bulb from the headlight

assembly.

7. Install a new headlight bulb and snap

the headlight bulb retaining wire into

position by aligning the wire with the

groove on the bulb.

OAC3089036TU

[2] : Low Beam Assist-Static Light

[3] : Turn signal light

8. Connect the headlight bulb socket

connector.

9. Install the headlight bulb cover by

Turn signal light, Low Beam

Assist-Static Light

1. Open the bonnet.

2. Remove the turn signal light or low

beam assist-static light bulb cover by

turning it counterclockwise.

turning it clockwise.

10. Install the wheel guard in the re-

verse order.

9-59

Maintenance

3. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

2. Reach your hand into the back of the

front bumper.

3. Disconnect the power connector

from the socket.

4. Insert a new bulb by inserting it into

the socket and rotating it until it locks

into place.

5. Install the socket in the assembly by

aligning the tabs on the socket with

the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

6. Install the turn signal light or low

beam assist-static light bulb cover by

turning it clockwise.

4. Remove the bulb-socket from the

housing by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots on the

housing.

5. Install the new bulb-socket into the

housing by aligning the tabs on the

socket with the slots in the housing.

Push the socket into the housing and

turn the socket clockwise.

6. Connect the power connector to the

socket.

7. Reinstall the front bumper under

Daytime Running Light &

Position Light, Front Fog Light

(if equipped)

cover.

Daytime Running Light &

Position Light

(LED Type, if equipped)

Daytime Running Light & Position Light

Your vehicle is equipped with LED

lights. LED lights do not have replace-

able bulbs. If the LED light does not op-

erate, we recommend that the vehicle

be checked by a HYUNDAI authorised

repairer.

OAC3089038TU

Front Fog light

OAC3089037TU

1. Remove the under cover by rotating

the screws and bolts.

9-60

09

5. To aim the low beam left or right,

Headlight and front fog light

aiming

Headlight aiming

turn the driver clockwise or counter-

clockwise. To aim the low beam up

or down, turn the driver clockwise or

counterclockwise.

Type A

To aim the high beam up or down,

turn the driver clockwise or counter-

clockwise.

Front fog light aiming

Type A

OAC3089039TU

Type B,C

OAC3083026TU

Type B

OAC3089040TU

1. Inflate the tyres to the specified pres-

sure and remove any loads from the

vehicle except the driver, spare tyre,

and tools.

2. The vehicle should be placed on a

OAC3N083026TU

flat floor.

3. Draw vertical lines (Vertical lines

passing through respective head

light centres) and a horizontal line

(Horizontal line passing through cen-

tre of head lights) on the screen.

4. With the headlight and battery in nor-

mal condition, aim the headlights so

the brightest portion falls on the hori-

zontal and vertical lines.

The front fog light can be aimed as the

same manner of the head lights aiming.

With the front fog lights and battery nor-

mal condition, aim the front fog lights.

To aim the front fog light up or down,

turn the driver clockwise or counter-

clockwise.

9-61

Maintenance

Aiming point (5 Door)

H1 : Lighting centre Ground clearance of Headlight Low & High Beam

H3 : Lighting centre Ground clearance of Front fog light

W1 : Lighting centre Distance between Headlight Low & High Beam

W3 : Lighting centre Distance between Front fog light

OAC3083027TU

Unit: mm (in)

W3

H3

Vehicle condition

Multi Focus Reflector

H1

W1

Fog

768

1,342

1,361

(53.6)

Headlight

Bi-Function Projection

Headlight

(30.23)

761.5

(29.9)

(52.8)

1,357

(53.4)

392

(15.4)

Without driver

Multi Focus Reflector

Headlight

761

(29.9)

1,342

(52.8)

385

1,361

(53.6)

With driver

(15.2)

Bi-Function Projection

Headlight

754.5

(29.7)

1,357

(53.4)

9-62

09

Aiming point (N line)

H1 : Lighting centre Ground clearance of Headlight Low & High Beam

H3 : Lighting centre Ground clearance of Front fog light

W1 : Lighting centre Distance between Headlight Low & High Beam

W3 : Lighting centre Distance between Front fog light

OAC3N083027TU

Unit: mm (in)

W3

H3

Vehicle condition

Multi Focus Reflector

H1

W1

Fog

768

1,342

1,309

(51.5)

Headlight

Bi-Function Projection

Headlight

(30.23)

761.5

(29.9)

(52.8)

1,357

(53.4)

378

(14.9)

Without driver

Multi Focus Reflector

Headlight

761

(29.9)

1,342

(52.8)

371

1,309

(51.5)

With driver

(14.6)

Bi-Function Projection

Headlight

754.5

(29.7)

1,357

(53.4)

9-63

Maintenance

Head light low beam

OAC3N080033TU

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting

the horizontal aiming.

4. If head light levelling device is equipped, adjust the head light levelling device

switch with 0 positions.

9-64

09

Front fog light

Based on 10m screen

OAC3089034TU

1. Turn the front fog light on with the driver (75 kg) aboard.

2. The cut-off line should be projected in the allowable range (shaded region).

9-65

Maintenance

4. Remove the bulb by pulling it straight

Side repeater light replacement

out.

5. Insert a new bulb in the socket.

6. Reassemble the socket and the lens

part.

7. Connect the bulb electrical connec-

tor.

8. Reinstall the light assembly to the

body of the vehicle.

Rear combination light bulb

replacement

OAI3089022

Type A

If the LED light does not operate, we

recommend you to have the vehicle

checked by a HYUNDAI authorised re-

pairer.

OAC3N083059TU

(1) Turn Signal Light

(2) Tail/Stop Light

(3) Reflex Reflector Light

(4) Rear Fog Light

(5) Back-up Light

OAC3083047TU

Type B

1. Remove the light assembly from the

vehicle by prying the lens and pulling

the assembly out.

2. Disconnect the bulb electrical con-

nector.

3. Separate the socket and the lens

parts by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the lens part.

9-66

09

2. Loosen the light assembly retaining

Type B

screws with a cross-tip screwdriver.

3. Remove the rear combination light

assembly from the body of the vehi-

cle.

OAC3N083058TU

(1) Tail Light

(2) Stop Light

(3) Turn signal light

(4) Reflex Reflector Light

(5) Rear fog Light

(6) Back-up Light

OAC3089041TU

[1] : Turn Signal Light, [2] : Tail/Stop Light

4. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

Turn Signal Light, Tail/Stop Light

5. Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

6. Insert a new bulb by inserting it into

the socket and rotating it until it locks

into place.

OAC3089048TU

7. Install the socket in the assembly by

aligning the tabs on the socket with

the slots in the assembly. Push the

socket into the assembly and turn

the socket clockwise.

8. Reinstall the light assembly to the

body of the vehicle.

OAC3089049TU

1. Open the tailgate

9-67

Maintenance

Rear fog light, Back-up Light

High mounted stop light

replacement

OAC3N083029TU

OAC3089046TU

[1] : Rear Fog Light, [2] : Back-up Light

1. Remove the rear tyre and wheel cov-

If the LED light does not operate, we

recommend you to have the vehicle

checked by a HYUNDAI authorised re-

pairer.

er.

2. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

3. Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

License plate light bulb

replacement

4. Insert a new bulb in the socket.

5. Reinstall the light assembly to the

body of the vehicle.

OAI3089029

1. Using a flat-blade screwdriver gently

pry the lens cover from the light

housing.

2. Remove the socket from the assem-

bly by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the assembly.

3. Remove the bulb by pulling it straight

out.

4. Install a new bulb.

5. Reinstall in the reverse order.

9-68

09

Interior light bulb replacement

NOTICE

Room lamp

• Type A

Be careful not to damage the cover,

tab, and plastic housing.

OAC3083030TU

• Type B

OIB074041

Luggage room lamp

OAC3089031TU

1. Using a flat-head screwdriver, gently

pry the lens from the interior light

housing.

2. Remove the bulb by pulling it straight

out.

3. Install a new bulb into the socket.

4. Align the lens tabs with the interior

light housing notches and snap the

lens into place.

9-69

Maintenance -> Light bulbs for Your Hyundai Bayon SUV Second Generation (2021-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals